C-Monster Standard Foot Switch Instructions - Power
Contents
1. FCC Part 15 19 Warning Statement Required for all Part 15 devices THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION FCC Part 15 21 Warning Statement NOTE THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE SUCH MODIFICATIONS COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT IC RSS GEN Sec 7 1 3 Warning Statement Required for license exempt devices ENGLISH This device complies with Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device FRENCH Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement IC RSS GEN Sec 7 1 2 Warning Statement Required for Transmitters ENGLISH Under Industry Ca2. ach small black cap when pressed should push down and come up when released If the black cap does not push down remove black cap rotate 1 uarter turn and re install i q Figure 4 SWITCH COVER Install rubber switch membrane back into the foot switch base and ensure that the rubber switch membrane is seated properly prior to installing the cover See Figure 4 T Locate a suitable area with a flat surface to mount the UP and DOWN foot switches Mark and drill a hole with 1 8 drill bit to fasten foot switches using the 6 screws C supplied do not over tighten oars Se QPOWER PGLE gt For Technical Support Call 813 689 9932 option 2
3. button will cause the anchor to retract or deploy automatically The anchor will continue to move in said direction until it either retracts completely up or senses a solid bottom surface down NOTE The wireless foot switch comes set to 100 speed setting This can be adjusted by downloading the C Monster App and connecting to the system via Bluetooth with your Android powered smart phone For more information refer to your Owner s Guide For Technical Support Call 813 689 9932 option 2 Changing the Battery and Installation Changing the Battery Figure 1 1 Remove the 3 screws with a 2 Phillips head screwdriver Take the foot switch to a dry location and separate the foot switch cover from its base using a small flat head screwdriver See Figure 1 Remove the rubber switch membrane and the circuit board from the foot switch base See Figure 2 SWITCH COVER Remove the battery from the holder on the back of the circuit board and replace with any CR2032 3V Lithium CIRCUIT BOARD Coin Battery Inspect the inside of the foot switch case for signs of moisture or damage to the rubber seal If the rubber seal appears damaged or if moisture is found please contact our technical support staff at Fi 813 689 9932 option 2 igure 3 CIRCUIT BOARD Place the circuit board back into its base with circuit BLACK CAPS board level and small black caps placed over each circuit board button See Figure 3 NOTE E
4. nada regulations this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that necessary for successful communication FRENCH Conform ment la r glementation d Industrie Canada le pr sent metteur radio peut fonctionner avec une antenne d un type et d un gain maximal ou inf rieur approuv pour l metteur par Industrie Canada Dans le but de r duire les risques de brouillage radio lectrique l intention des autres utilisateurs il faut choisir le type d antenne et son gain de sorte que la puissance isotrope rayonn e quivalente p i r e ne d passepas l intensit n cessaire l tablissement d une communication satisfaisante IC RSS 102 Sec 2 6 Warning Statements ENGLISH The applicant is responsible for providing proper instructions to the user of the radio device and any usage restrictions including limits of exposure durations The user manual shall provide installation and operation instructions as well as any special usage conditions to ensure compliance with SAR and or RF field strength limits For instance compliance distance shall be clearly stated in the user manual FRENCH Le mode d emploi des appareils destin s l utilisation contr l e doi
5. t HPU 1 Press and hold the PROGRAM button on the top of the PROGRAM LED unit for 3 seconds until the LED turns green in color HPU will also beep The unit is now ready to be paired with the foot switches Press the UP foot switch button for 1 second and release See Figure 1 The green LED on the unit s will initially turn off then flash green steadily HPU will also beep indicating that the pairing is complete NOTE If dual units are installed repeat Steps 1 3 to pair multiple units to a single foot switch Up to ten 10 wireless controllers can be programmed to each unit For the DOWN foot switch button repeat Step 1 to enter programming mode Next press the DOWN foot MICRO Driver Unit switch button for 1 second and release See Figure 2 The green LED on the unit s will initially turn off then PROGRAM flash green steadily HPU will also beep indicating that the pairing is complete The foot switches are now paired to the unit Test their functionality by following the operating instructions to ensure that the pairing procedure was completed successtully Figure 1 Figure 2 O r Operating Instructions 1 To raise or lower the Power Pole anchor press and hold either the UP or the DOWN foot switch button The anchor will only continue to move so long as you keep the button depressed Auto Mode Double tapping depressing and releasing 2 times within 1 second either the UP or the DOWN foot switch
6. t aussi inclure des informations sur les caract ristiques de fonctionnement de l appareil les instructions de fonctionnement pour assurer la conformit avec SAR et ou les limites d intensit de champ RF informations sur l installation et l exploitation d accessoires pour assurer le respect des SAR et ou les limites d intensit de champ RF et les coordonn es o l utilisateur peut obtenir des informations sur l exposition canadienne de radiofr quences et la conformit Autres renseignements connexes peuvent galement tre inclus To activate your warranty or find a Power Pole Certified Warranty Center go to www power pole com UlMarine 9010 Palm River Road Tampa Florida 33619 phone 813 689 9932 fax 813 689 8883 power pole com SYSTEMS INC POWER POLE SHALLOW WATER ANCHOR Wireless Standard Foot Switch Congratulations on your purchase of the Power Pole Foot Switch featuring C Monster Control System To add the Power Pole Foot Switch follow these simple step by step instructions Compatible with all C Monster Control Systems Hardware Installation Tools A Qty 1 Up button e 2 Phillips head screwdriver B Qty 1 Down button e 1 8 drill bit C Qr 6 8 x 1 5 Pan head screws e Electric or battery operated drill If any hardware is missing from this package please contact Tech Support immediately at 813 689 9932 opt 2 Pairing and Operation Pairing Foot Switches Hydraulic Pump Uni
Download Pdf Manuals
Related Search