OPERATING INSTRUCTIONS Dust Extractor
Contents
1. but the user must note that the machine components must be protected from knocks and blows Filter and sealing connections are carefully chosen for the environment of the operator Therefore the machine must be handled with care if it is to work correctly for many years Problem Motor does not start Motor stops immediately Motor runs but there is no suction Motor runs but suction is poor Dust blows from motor Abnormal noise Cause No power Switch defective Wrong fuse Hose not connected Hose blocked No plastic bag Damage to the hose Blocked filter Top cover loose Dirt in the flap Sealing defective Defective or loose filter Procedure Connect the machine Change Connect the correct fuse Connect the hose Clean the hose Install plastic bag Change hose Change filter Adjust Clean the flap Use protective eguipment Change current seal Adjust or change Order service SAVE THESE INSTRUCTIONS Revision 2 VOLTAGE POWER MAX AIR FLOW MAX VACUUM HOSE INLET FINE FILTER HEPA FILTER SOUND LEVEL TECHNICAL DATA CFM H20 Inch PLASTIC BAG SYSTEM DIMENSION LxBxH WEIGHT Revision 2 T7500 230 VAc 3 fas 60Hz 7500 W 353 110 33 feet x 3 Ze gt 99 5 Filter area 25 ft HEPA H13 Filter area 54 ft 74 dB A Longopac 49x27x69 in 417 pound T8600 480 VAc 3fas 60 Hz 8600W 353 110 133 feet x 3 O 377 gt 99 5 Filter aere2. 25 ft HEPA H13 Filter area 54 ft 74 dB A Longopac 49x27x69 in 417 pound OM OVERENSSTAMMELSE DECLARATION OF CONFORMITY DECLARATION DE CONFORMITE ERKL RUNG DER BERSTIMMUNG SAMSVARSERKL RING Pullman Scandinavian AB Industriv gen 10 S 777 34 SMEDJEBACKEN F rs krar under eget ansvar att maskinen Declare under our sole responsibility that the machine Certifie sous sa propre responsabilit que le produit ciapr s Versichern auf eigener verantwortung dass das Produkt Forsikrer under eget ansvar at maskinen T7500 Nr No 0700492c0001 T8600 Nr No 0600403a0001 Tillv ar Manufact year Baujahr 2006 som omfattas av denna f rs kring r i verensst mmelse med standarder included in this declaration follows the provisions of the est conforme aux aux normes suivantes den folgenden Normen entspricht er i overensstemmelse med standarder SS EN 292 1 SS EN 60 204 1 1993 11 30 SS EN 55011 1989 SS EN 50082 1 SS EN 60335 1 SS EN 60335 2 69 amp A1 enligt villkoren i according to selon laut i henhold til vilk rene i Machine Directive 98 37 EEG Low Voltage Directive 73 23 EEG EMC Directive 89 336 EEG SMEDJEBACKEN 2006 01 01 Torbj rn Bengtsson VD General Manager Revision 2 7 Exploded view T7500 T8600 Z 33 Revision 2 Spare parts list T7500 T8600 Antal Qty 18600 Benamni
3. 8 Pullman Ermator OPERATING INSTRUCTIONS Dust Extractor T8600 READ ALL INSTRUCTIONS BEFORE USING Introduction Dear Customer Thank you for choosing Pullman Ermator as your supplier We hope that the Pullman Ermator dust extractor will be to your satisfaction and meet your expectations Pullman Ermator has been manufacturing professional dust extractors since 1966 and has over the years acguired a genuine technical knowledge in this area We strive to improve in our product segment and will continue to supply the market with new eguipment Please feel free to browse information about our product programme on our web site www pullman ermator se Notice These instructions are only for the dust extractors T8600 The dust extractors T8600 can only be used with dry non explosive material Pullman Ermator will not be held responsible if the air cleaner is used for other applications or has been used in ways other than those outlined in this instruction manual Before using the machine please read the safety regulations carefully Read the complete instruction manual before using the dust extractor All spare part used for the dust extractor T8600 must be those specified by Pullman Ermator Revision 2 1 Unpacking When unpacking the machine please check for damage and that that following accessories are included e The hose with end fittings e Steel tube e Floor nozzle If any of above mentioned parts are missi
4. cordingly the user should wear protective glasses protective gloves and a breathing mask conforming to protection class FFP3 WARNING Switch off the machine and pull the plug out of the socket Main filter Loosen the two latches between the tank and the lower cyclone Loosen the two latches at the hose connection between the tank and the absolute filter cover Rotate the tank forwards Rotate the filter plate counter clockwise 10 degrees and carefully turn filter and holder upside down Place a plastic bag over the filter unit Lift the filter carefully and pinch up the bag by hand and then tie the bag up This bag must be properly disposed of Insert a new complete filter pack in reverse order Only original filters may be used Absolute filter Loosen the three latches holding the filter cover and carefully Lift the filter up and into a plastic bag This bag must be properly disposed of Insert new filters in reverse order Revision 2 3 Service WARNING Before cleaning and servicing the machine you must switch the machine off and pull out the plug from the outlet e Avoid cleaning with a high pressure cleaner If necessary do not direct at the openings on the machine especially the opening for the cooling air e Before moving the machine from the working area the machine must be cleaned Furthermore the inlet must be locked using the expanding plug attached e All other equipment must be considered to be conta
5. fugal force and partly by gravity Air and finer particles then pass through the tube filter where separation takes place The machine is designed for filter cleaning by reverse air pulse The separated dust accumulates in the cyclone until the machine is switched off when it drops through the bottom flap into the plastic bag Warning Before starting the machine check that the inlet valve is in the lower position Use Before use the user must be trained in the handling of the dust extractor and the hazardous dust Warning Connect the electric plug to a power outlet with the correct voltage see the nameplate The filter must be cleaned from time to time This must be done before changing the plastic bag It can also be done when the work is complete or when there is poor suction Procedure Unplug the hose so that the inlet is covered Cover the intake of the overpressure valve placed between the two hoses connecting the main tank and the cover for the micro filters let the machine build up vacuum for a few seconds then quickly push down on the top handle and release it slowly Repeat this procedure 5 10 times If suction remains poor the filter should be replaced The plastic bag may only be replaced after cleaning the filter The plastic bag must be tied up after removal Only use original parts Filter change Risk of dust dispersion Use of personal safety eguipment Unhealthy dust can be spread during filter change Ac
6. minated and be treated thereafter e possible use a special suitable room e Proper personnel protective equipment must be used e After a service all parts that are contaminated must be taken care of properly in plastic bags according to all regulations e the vacuum cleaner has to be used for other purposes it is extremely important that the vacuum cleaner is cleaned to avoid the spread of hazardous dust Accessories Part no Description No machine 200600596 Complete filter set 1 pcs 200600595 MF5500 HEPA filter 2 pes 1337032 Cleaning set 1 pcs 1376013 Longopac 4 pack 1 pcs For other spare parts see the enclosed spare parts list Warranty All Pullman Ermator devices and accessories have a 12 month factory warranty for material and manufacturing defects The warranty extends to 36 months when returning the attached warranty slip Do not attempt to repair the suction apparatus without the consent of the manufacturer The warranty does not cover defects which are the result of normal wear and tear negligence defective use unauthorised repair or the suction apparatus being connected to the incorrect voltage In the event of any complaint the suction apparatus or an agreed part of it must be returned to us or our authorised representative for warranty examination and for any warranty repair or replacement Revision 2 4 Problem solving The dust extractor T8600 is designed and manufactured for severe environments and tasks
7. ng Description Handle 200600657 Tank complete 15 Filter stretcher Holder kit 1351162 Anti skid 5 Holder for longopac HEPA filter kit 20060071 o oO ai al ag m SE Revisio Pullman Ermator AB Industriv gen 10 777 34 Smedjebacken Tel 46 0 240 66 09 60 Fax 46 0 240 66 30 60 Email info pullman ermator se
8. ng please contact your local distributor or our sales representative Safety Instructions Handling Warning e Cables damaged through crushing or splitting can be dangerous if used and should be replaced immediately Risk of personal injury Warning e Do not connect the machine to an unearthed socket Risk of personal injury Warning e Make sure the assembly area is firm so the dust extractor does not tip over Risk of personal and material injury Warning e Risk of pinching when handling the toggle fastener Warning e The machine must not be used in environments where explosive gases may be present Serious risk of explosion Service Warning e Remove the plug from the wall socket when carrying out maintenance work Risk of personal injury Warning e Dust can be spread when the coarse filter and the absolute filter are replaced that can be dangerous to health Accordingly the user should wear protective glasses protective gloves and a breathing mask conforming to protection class FFP3 Warning e Do not puncture the absolute filter Risk of dust dispersion Revision 2 2 Function The machine is used for sucking and separating dry non combustible dust with an explosion limit value of 0 1mg m The motor is started by the switch Dust laden air is then sucked through the inlet valve at high speed via the suction hose The air is slowed down by the cyclone and coarse dust particles are separated out partly by centri
Download Pdf Manuals
Related Search