User's Manual Paintball Gun
Contents
1. The safety provides protection against accidental or unintentional discharge under normal usage when properly engaged ON To engage the safety push the button all the way to the right To release the safety push the button all the way to the left See Figure 2 which illustrates the positions of the safety Push button on right side of gun to disengage safety Push Button on left side of gun to engage safety Figure 2 The Safety ON and OFF Positions The Phantom User s Manual Description and Operation CO Installation Stock Class Place 12 gram CO cartridge in stock housing Screw stock housing with cartridge onto puncture adapter This action pierces cartridge and pressurizes gun 12 gram CO s gt Figure 3 Stock Housing CO Installation Puncture Adapter Removal To remove the puncture adapter use a 3 8 hex key Figure 4 Puncture Adapter Removal 4 The Phantom User s Manual Description and Operation CO Installation CO Tank Thread the CO tank into the air adapter Tighten with hand to prevent leaks If you have a leak check O ring on tank The gun is now pressurized 4 Tank Air Adapter _ gt Figure 5 CO2 Tank Installation Load and Fire Paintballs Observe all safety precautions Pour paintballs into ammo box or insert paintball tube with paintballs into horizontal feed for stock class gun Hold the gun firml2. User s Manual Paintball Gun User s Manual Component Concepts Inc The Phantom Paintball Gun User s Manual The information in this manual is subject to change without notice and does not represent a commitment on the part of Component Concepts Inc CCI reserves the right to make improvements to products without incurring any obligation to incorporate such improvements in products previously sold This manual contains information protected by copyright No part of this manual may be photocopied or reproduced in any form without prior written consent from Component Concepts Inc Copyright 1989 2002 by Component Concepts Inc All rights are reserved The PHANTOM is a registered trademark of Component Concepts Inc Component Concepts Inc 530 South Springbrook Road Newberg OR 97132 The Phantom User s Manual Phone 503 554 8095 Fax 503 554 9370 Precautions Safety Your Responsibility 1 Description and Operation IHERKOAUCHON Ecke 2 SPECHLAUONS en ee 3 The Gun Safety 3 CO Installation 2 22 tere 4 Puncture Adapter Removal 0 ssseeeeeeees 4 Load and Fire Paintballs 2422240004000 5 Velocity Adjustment HH 6 Service and Maintenance Field SUP DINO fsa sie Ai era 7 Cup Seal and O ring Replacement 8 General Maintenance 4444 nn 8 Service Note Senidea ernennen
3. 10 ParlsEist reene a AO toa ea 12 Expl ded IATA lt 1 AANE 13 ACCESSOS einama ae esee ae dees Ee 14 Warranty and Disclaimers Waranty zu 15 Disclaimers ianari e 16 ii The Phantom User s Manual Precautions Safety Your Responsibilit The Phantom is designed and built to provide safe and dependable service if handled according to instructions Read and understand the instructions and warnings in this manual before using the Phantom Failure to do so could result in personal injury or property damage Phantom owners must comply with the following basic safety precautions These precautions are given here for your safety and for the protection of the gun Review them carefully before using or performing general maintenance or repairs on the gun WARNING The Phantom is a dangerous weapon if mishandled This gun is not a toy nor is it intended for use by persons under the age of 18 Follow the basic rules of safe firearms handling and the laws governing the ownership and use of gas fired guns Careless handling of the Phantom or any other CO powered gun may cause serious injury Do not handle this gun until you are thoroughly familiar with its mechanical characteristics Always wear approved eye protection when operating this or any paintball gun Pressurize with CO only while the gun is in use Keep exposed flesh away from escaping CO2 Always carry the gun with the safety ON Never point the gun in t
4. If your fitting should leak the internal O ring in the fitting needs to be replaced De gas the marker Remove the tube by push ing in the collet and pulling the tube out If you have a metal type tube you also need to remove the rear thumb screw Pull and wiggle the collet back and forth to extract from fitting body Replace the O ring 9428 Compression metal line assembly is the newest type vertical air connection and requires a 7 16 wrench for disassembly The rubber sleeve is designed for positive seal with proper compression 10 The Phantom User s Manual Service Notes Service and Maintenance The Phantom User s Manual Service and Maintenance Parts List 12 Part 9115 9103 9116 9062 9051 9052 9045 9049 9048 9068 9200 9212 9311 9300 9306 9307 9304 9305 9316 9029 9070 9003 9011 9013 9410 9038 9039 9806 9415 9805 9414 9015 9024 9458 9424 9429 9434 9435 9417 9206 9205 3045 9441 9442 Description Retainer Power Tube Modified Short Power Tube Assembly Modified Anti Kink Hammer Assembly Main Spring Tuned Port Compensator Bolt 21A 14 Nylon Set Screw 10 32x1 8 Bolt Assembly TPC Adjusting Rod Hex Pump Bolt Rod with Nut 8 32 Thumbscrew Front Frame Assembly 28 29 30 31 Lock Washer Grip Screw 1 4 20x3 4 SHCS Grip Cover Grip 10 32 Thumbscrew Rear Feed Port Cover Adjusting Rod TPC Breech Top Feeding Horizontal Fe
5. ed Screw 8 32x5 8 SHCS Stock Housing Puncture Pin Assembly includes 40 Puncture Seal O ring 77 614 Stock Puncture Adapter Assembly 39 40 41 43 O ring 15 10 Round Extension Tube 15 Round Extension Tube Ball Retainer Vertical Adapter Screw 8 32x1 4 BHSS Vertical Adapter Push to Connect Elbow Vibra Lock Elbow Metal High Pressure Tube Air Adapter Side Fitting Nylon Washer Return Spring 45 Grip Frame Sleeve Compression Nut The Phantom User s Manual Exploded View Service and Maintenance Item Part 2 9009 3 9006 9007 9008 4 9069 5 9420 9 9036 10 9112 11 9111 12 9113 13 9110 14 9046 The Phantom User s Manual Description Gravity Feed Breech 11 Screw in Barrel 9 Screw in Barrel 14 Screw in Barrel Hex to Slot Adjusting Rod Adapter Air Adapter Valve Spring Cup Seal Eyelet Cup Seal Assembly 10 11 12 O ring 12 13 Service and Maintenance Accessories l SS Braided Air Line Hose Adapter 9439 9455 45 Style Grip 3045 Bottom Line Air Adapter Vertical Adapter Kit Telescope T Stock 9325 45 Air Adapter 3050 L Stock Adapter 9327 Twist Change Adapter 9042 14 The Phantom User s Manual Warranty and Disclaimers Warranty To confirm your warranty fill out and return the enclosed warranty registration card The 180 day limited warran
6. eld Stripping WARNING The Phantom is a dangerous weapon if mishandled Never clean lubricate disassemble assemble or work on the gun while it is pressurized Observe safety precautions The working parts of the Phantom are either hard anodized black oxide electroless nickeled or stainless steel These materials and plating procedures ensure long life however the bolt and hammer must be kept clean and lightly oiled Do not put oil on the O ring seals To field strip Remove the CO and paintballs Remove the front and rear frame mounting thumbscrews and separate the grip frame assembly from the breech barrel assembly Pull the air adapter out of the breech The hammer and main spring will slide out Remove the bolt by pulling the bolt rod up slightly to release the bolt and tilt the breech so the bolt slides out WARNING Any attempted modification unauthorized service or tampering may cause the Phantom to become unsafe or malfunction The Phantom User s Manual Service and Maintenance Service and Maintenance Cup Seal and O ring Replacement Service Notes An extra O ring and cup seal has been supplied to help you To replace nylon tubing push the collet of the fitting in and pull sustain top performance of your gun The O ring is used in both the tubing the bolt and power tube assembly The white seal is for the cup seal assembly Observe safety precautions Field strip the air adapter from t
7. he breech and use a 11 16 open end wrench to remove the power tube assembly Unscrew the To prevent leaks make sure that the end of the nylon tube is cut tube from the seal and turn seal over or replace if performance smooth and round The end of the tube must be inserted pass is poor or during normal operation the gun does not fire the O ring at the base of the fitting General Maintenance The vertical air system may have or may be replaced with a hard line metal tube To install or replace remove the rear Do not store with CO or with gun cocked thumb screw and pull air adapter back but not out of the breech Slide the short angle of metal tube into the vertical adapter The gun must be kept clean for safe and reliable operation Rotate the vertical adapter until tube is aligned with center of air adapter fitting Push the air adapter back into place and secure The bore of the barrel must be clean and dry for ultimate with thumb screw performance Use a paintball squeegee and or swab for a 68 caliber barrel The barrel may be unscrewed for easy cleaning Inspect components to determine if they are in proper working order If you are unsure contact Component Concepts Inc or your dealer If the performance changes dramatically you may need to return for repair Before shipping be absolutely sure that the CO is removed 8 The Phantom User s Manual The Phantom User s Manual 9 Service and Maintenance Service Notes
8. he direction of anything you do not intend to mark Never look directly into the barrel Use only 68 caliber paintballs Do not attempt to service the gun without first removing the CO Do not fire the gun at a target that is less than three feet away For everyone s protection exercise common sense and safety during all situations The Phantom User s Manual 1 Description and Operation Introduction The Phantom is a 68 caliber pump action CO powered gun designed to fire paintballs which burst on impact to mark the aiming point The Phantom cocl all when the pump arm is pulled fully back and returned to its full forward position Releasing the safety and squeezing the trigger fires the gun The gun must be pressurized with COzto cock The desigr mechanism includes a rapid fire capability n the trigger the gun fires with iantom s major components nderstanding the instructions is manual Air Adapter gt Trigger Safety 2 The Phantom User s Manual Description and Operation Caliber 68 Mechanism Pump Action Power CO Safety Trigger Block Muzzle Velocity 180 325 fps Adjustable F Stamped less than 200 fps Non Adjustable Sights Rear sight w Slide Rails Weight 1 8 2 Ibs Length 20 to 34 inches Barrel Aluminum Alloy Roller Burnished 8 14 inch Material 6061 T 6 Aluminum Alloy The Gun Safety The Phantom safety is a push button located next to the trigger
9. s City Comments fold Warranty Registration Card Price Date Purchased State Zip Phone State Zip Phone Component Concepts Inc 530 South Springbrook Road Newberg OR 97132 PLACE NECESSARY POSTAGE HERE COMPONENT CONCEPTS INC 530 South Springbrook Road Newberg OR 97132 www phantomonline com
10. ty begins on the date of purchase This warranty applies to all models of the Phantom products and accessories manufactured or sold by Component Concepts Inc CCl You are the owner if you are the original purchaser of the Phantom products from either CCI or an authorized dealer This warranty only applies to original owners and is not transferable CCI pledges to you the owner that the Phantom products are free from defects in materials and workmanship for 180 days from the date of purchase During the term of this warranty at no additional charge to the owner excluding shipping CCI will repair or replace any defective parts of the Phantom products with new or at the option of CCI refurbished parts The owner must prepay any shipping charges In addition the owner is responsible for insuring any product returned and assumes the risk of loss during shipping All parts and products replaced under this warranty become the property of CCI To obtain this repair or replacement service the owner must return the entire Phantom product to Component Concepts Inc 530 South Springbrook Road Newberg OR 97132 We are open 9AM to 5PM PST Monday through Friday Telephone 503 554 8095 Fax 503 554 9370 The Phantom User s Manual 15 Warranty and Disclaimers Disclaimers This limited warranty does not extend to any products not purchased from Component Concepts Inc CCI or an authorized dealer This limited warrant
11. y also does not extend to any products damaged or made defective A as a accident misuse abuse B by the use of parts not manufactured or sold by CCI C by modifications or D as a result of service or modifications by anyone other than CCI or an authorized dealer or service provider Except as expressly set forth above CCI makes no other warranties express or implied including but not limited to any implied warranties of merchantability and fitness for a purpose beyond its designed use and CCI expressly disclaims all warranties not stated here In the event the Phantom product is not free from defects as warranted above your sole remedy as the owner shall be repair or replacement as provided above CCI will not be liable to the owner or to any user for any damages including any incidental or consequential damages expenses lost wages or other damages arising out of the use of or inability to use safely CCI products Some states do not allow the exclusion or limitation of incidental or consequential damages for consumer products and some do not allow limitations on how long an implied warranty last so the above limitations may not apply to you This warranty gives you specific legal rights and you also have other rights which vary from state to state The Phantom User s Manual FOLD DOWN AND TAPE AFTER COMPLETING REGISTRATION FORM Product Purchased Serial Number Owner Address City Purchased From Addres
12. y in the shooting hand while using the other hand grasp the pump and pull it to the rear as far as it will go then push forward in a continuous movement This action chambers a paintball and cocks the firing hammer The gun is now fully loaded When ready to fire push the safety button to the OFF position and squeeze the trigger The Phantom User s Manual 5 Description and Operation Velocity adjustment Temperature and altitude influences the performance of COz The force generated by the main spring is adjustable to compensate for these environmental effects Although many playing fields allow velocities up to 320 feet per second fps the Phantom performs best at 280 fps To adjust velocity Observe all safety precautions Visually check to be sure that no paintballs remain in the chamber Use adjusting rod or unscrew barrel and use standard screw driver to turn the tuned port compensator Turning the compensator clockwise will increase velocity and counterclockwise will decrease velocity Caution Turning the compensator clockwise more than six turns unseats it causing inconsistent performance and damage to threads Adjust the nylon set screw to provide enough drag to prevent the compensator from moving freely Do not overtighten you will strip out the nylon set screw Adjustment _ Rod eh aa Increase Screw we Figure 6 Compensator Adjustment 6 The Phantom User s Manual Service and Maintenance Fi
Download Pdf Manuals
Related Search