G.S.I AC Controller Installation and User Guide
Contents
1. Figure 17 Twelve Hour Cycle Setting Example If you increase past 24 hours the display changes to d 01 indicating one day You can continue to press F to increase the number of days amp eGalcon s G S I Controller Installation and User Guide Figure 18 Six Day Cycle Setting Example 4 After setting the desired cycle length press G to progress to the next screen which automatically saves the change Setting the Irrigation Start Day and Time The start day is the number of days between the day you define an irrigation program today and the day the program actually begins operating The start time is the time of day the program begins To set the start day and time 1 From the Main screen press G until the Start Day screen appears Figure 19 Figure 19 Start Day Screen Example The default display is d 00 which indicates zero days If you set this value for the start day the irrigation program will start on the current day at the defined start time If that time has already passed for the current day the program starts at that time the next day 2 Press and to increase and decrease the number of days In Figure 19 the value is set to 10 days The maximum supported value is 30 days 3 Press G to save the defined start day and continue to define the start time in the Start Time screen The default setting is Off which means that the irrigation program never starts 4 Press and2. eecalcon G S I Controller Installation and User Guide 10 11 12 13 Galcon does not give any warranty or guarantee whatsoever in respect of any Product or any part s thereof which has not been manufactured and distributed by the Galcon and which has not been purchased from the Galcon or any of its authorized dealers whether such products are branded with any trademarks similar to any trademark belonging to or used by Galcon After replacement or repair of the Product the Warranty for the new or repaired Product shall be valid only for the non expired period of the original Warranty Period Any defective Products or part s which has been replaced shall become Galcon s property Galcon reserves the right to charge the Customer if any warranty service is requested and carried out but no fault is found in the Product or if such defect fault is not under Galcon s Warranty Notwithstanding anything to the contrary Galcon shall not be responsible and or liable under any circumstances and in any way for any loss damage costs expenses expenditures responsibility and or liability including of Customer and or any third party including without limitation direct and or indirect including incidental and or special and or consequential however arising including in respect of damages to or loss of property and or equipment loss of profit loss of use loss of revenue or damages to business or reputation whether o
3. to set the start time The possible range of values is 0 00 to 23 59 Alternatively you can cycle through the time settings until reaching the open option Setting the start time to open causes the irrigation cycle to start immediately after you save the start time setting overriding the defined start day 5 Press G to progress to the next screen which automatically saves the change is 4eGalcon G S I Controller Installation and User Guide Cancelling an Irrigation Program Start To cancel an irrigation program start 1 From the Main screen press G until the Start Time screen appears 2 Press until the start time is set to Off This defines that the irrigation program will never start 3 Press G to progress to the next screen which automatically saves the change Initiating Immediate Irrigation for a Station In addition to defining an irrigation program you can initiate any station to immediately begin irrigating The irrigation is performed for the amount of time defined for that station s duration in the irrigation program you created using the controller s direct interface This is true even if you have already uploaded a different program from the G S Web User Interface If no duration has been defined the duration used is one minute To initiate immediate irrigation for a station 1 From the Main screen press G until the Start Time screen appears 2 Press to select a station
4. Warranty Period provide limited warranty for the Products as provided for and subject to the provisions and limitations of this Limited Warranty Certificate 2 Galcon s Warranty for the Product only extends to the original purchaser of the Product the Customer who upon requesting warranty service must present Galcon with a valid purchase receipt Failure to produce the said documentation will result in the request for warranty being null and void 3 GALCON warrants to the Customer that the Product shall materially conform to the description in Galcon s documentation and shall be free from defects in material and workmanship Accordingly Customer s sole and exclusive remedy under this warranty is the repair or to Galcon s sole discretion the replacement of the Product or any part s according to the terms of this Warranty and no other remedy shall be available Therefore if within the Warranty Period the Product is proven to be defective by reason of faulty workmanship or materials by Galcon Galcon undertakes with reasonable promptness to have the defective Product or any part s thereof repaired or at Galcon s discretion replaced All subject to the terms and conditions of this Limited Warranty Certificate 4 Galcon s warranty for the Product or otherwise shall not apply to any of the following i any conduct by act or omission not by Galcon including any misuse abuse of any Product or part s the
5. control cupboard through the marked holes Figure 4 and Figure 5 with the aid of three screws Close the screws by hand only For water sealing cover the screws with the supplied cover caps Figure 6 4 Close the internal casing and fasten its screws 5 Swing the control panel back into place 6 Close and lock the controller cover escaicon s G S I Controller Installation and User Guide Figure 1 Open Controller Cover Figure 5 Mounting Screw Holes Dimensions Figure 6 Inserting the Mounting Screws with Cover Caps Establishing the Electrical Connections The AC G S Controller has the following output connectors Se 12 or 24 irrigation valves Ss Master valve e calcon G S I Controller Installation and User Guide The G S Controller has the following inputs Ss Rain sensor SG Water meter Flow sensor Connecting the Solenoids to the Controller To connect the solenoids to the controller 1 Insert the solenoid wires through the cable gland at the bottom of the controller and connect them 2 Connect one wire coming from the solenoid to one of the outputs labeled with a number 1 24 3 Connect the second wire to one of the common outputs labeled C __ _ _ E RR ER ER ER ER Rz ES Figure 7 Controller Terminal Blocks ist GC Note It is highly recommended tha
6. place by turning the latch back until it clicks s calcon G S I Controller Installation and User Guide 4 Close the internal casing and fasten its screws 5 Swing the control panel back into place 6 Close and lock the controller cover Connecting a Rain Sensor and Flow Meter The GSI unit supports the following input devices Se Rain sensor Se Flow meter pulse type To connect the input wires Se Rain sensor Connect one of the rain sensor wires to the connector labeled Rs and connect the second sensor wire to one of the connectors labeled C The polarity of the wires is not important Se Flow meter Connect one of the flow meter wires to the connector labeled Ws and connect the second wire to one of the connectors labeled C The polarity of the wires is not important e amp Note You must define the rain sensor and flow meter in the G S I Web User Interface before you can use them Inserting a SIM Card The SIM card case is located on the upper left side of the controller board e Note Your SIM card definitions should already have been set by the manufacturer If you are inserting an independent SIM card and you need to set its definitions yourself refer to the document SIM Card Definitions provided by Galcon To insert a SIM card 1 Unlock and open the controller cover Figure 1 2 Swing out the control panel Figure 2 3 Locate the SIM card case esGalcon v G S I Controller In
7. to move the A cursor and select the station for which you want to define the irrigation duration 3 Press and to set the irrigation duration for the selected station In Figure 15 the duration set is for 2 hours and 40 minutes for station 3 A duration of 0 00 sets the station to never open its valves and therefore the sequence skips to the next station immediately Figure 15 Duration Screen Example 14 calcon G S I Controller Installation and User Guide Setting the Irrigation Cycle Time You can set an irrigation program to occur one time only or to occur repeatedly according to a cycle When setting a recurring cycle the cycle value you set defines the length of time in days which passes between irrigations program start times To set a one time irrigation program 1 Press G until the Cycle screen appears Figure 16 The message Once is displayed by default indicating that the cycle pattern is set to one time only If a cycle value other than OncE was previously set for the system press repeatedly until the message OncE appears 2 Press G to progress to the next screen which automatically saves the change Figure 16 Cycle Screen To set cyclical irrigation programs 1 Press G until the Cycle screen appears Figure 16 2 Press once The display changes from OncE to h 00 indicating zero hours 3 Press and to increase and decrease the number of hours
8. 3 Press bk The station immediately starts irrigating for the length of its defined duration 4 Optionally press F or to increase or decrease the duration of the current irrigation Resetting the Controller If a technical problem occurs you may want to reset your G S I Controller To reset the controller Va as Press the Reset button located in the top left corner of the G S I Controller s circuit board The reset process clears the controller s RAM and performs the flowing sequence of operations a All the screen icons appear simultaneously on the screen and gradually disappear after a few minutes b The screen displays the controller s serial number followed by the current firmware version on the controller c The screen displays the numbers of the valves connected to the controller The controller starts closing the valves one by one as each valve is closed its number disappears from the screen and the CL OS message is displayed Optionally press to abort this process and skip to the next operation d The controller establishes communication with the server the fei icon flashes on the screen as long as the controller is in communication mode eecalcon 17 G S I Controller Installation and User Guide e The controller ends communication and resumes normal operation AlL Note Resetting the controller does not delete or cancel the locally created irrigation program Pausing and Resuming Irrigation f
9. G S 1 AC Controller Installation and User Guide December 2012 Va KEN Gaicon Computerized Control Systems lt The Science of Solutions G S I Controller Installation and User Guide Information in this documentation is subject to change without notice and does not represent a commitment on part of Galcon The software described in this document is subject to the license agreement that is included with the product which specifies the permitted and prohibited uses of the product Any unauthorized duplication or use of this documentation in whole or in part in print or in any other storage or retrieval system is prohibited No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form by any means for any purpose other than the purchaser s personal use without the permission of Galcon 2012 Galcon All rights reserved Contact Us Galcon Kfar Blum 12150 Israel Tel 972 4 6900222 Fax 972 4 6902727 E mail info galconc com Visit us at www galconc com 2 amp calcon Table of Contents 1 ENE EO CNG d EE 3 Goal C OME Oller le e EE 3 2 Setting Up the G S I COMO eh vies vicninisdcnenecuientwenssccunadanenunduulcneuacnientwdneesieuasencnuwiuescneueueleneunnl 5 let ie ebe enge E 5 installing On a Wall OF ia Conto CUDDOGIG EE 5 Establishing the leg ve Reen de CEET 6 Connecting ne Solenoids to the let 7 CONN C
10. O AGC FOV Ci EE 8 CONNECHING Backup Ee E 8 Connecting a Rain Sensor and Flow Meter NNN NENNEN NEEN EE NEE ENEE NEEN 9 Inserting a SIM C rd EE 9 3 On Site Controller Goerend een CERN een Eeer eeh egen 11 Klee ET 11 Establishing Communication with the Server oo ccccccecc tee eee eee eee eee n ee eee EASE EERE Rene n deen aaeee eS 12 Manually Setting Tne Controler CICK EE 13 Te ul e Station ig EE 13 Creating an Irmigalion Progra EE 14 Setting THIgauion Program Durations EE 14 Seng the EE CY CIC TIMO vised ee Eder 15 Setting he Igation Start Day and E RE 16 Cancelling an Irrigation Prograni Start EE 17 Initiating Immediate Irrigation for a Staion NEE 17 ge luet eeng OOT EE 17 Pausing and Resuming Irrigation from the Controller cece ce eeeee eee nesses esses eee eee eeeeeaaaenenees 18 e dell AIC US saxavesadonssenoeavatoueaencracecanaronpiatacanoea var enmeenceereeererereieterereeevaresmeeucrantisrarereieuteasseereeerss 18 SEN EE ete eee ee ee ee ee eee EE EE 19 CMCC NO FAUT ACS soy os ans eet ne eco ae Era canes veteeen ees 19 EE TT VSS Se be 19 Locking and Unlocking the SCreen EE 19 4 Technical SPCCITICAUONS biisskeesinntinrinnnicersierai ee ORE 21 5 Warranty cesieitaimescdcaeensvarvacawnainaiie ieee aA enn veuiesen A A 23 eecalcon 1 List of Figures FOO Opon COMMONC COVEN EE 6 FOUG A COME Oh irae SW QUWI EE 6 Figures Opening tne Internal Casing EE 6 Figure 4 Mounting Screw Holes on Back Of Unit e 6 Fig
11. ectly operate the irrigation system at the desired times the controller clock must first be set correctly The controller clock is automatically updated every time the controller preforms communication with the server However if necessary you can also manually set the time To manually set the controller time 1 Press and hold until the hour and minutes values in the displayed time start flashing This indicates that the clock is in time setting mode Set the current time using the and buttons 2 Press G to exit time setting mode and press G repeatedly until the Main screen is displayed Verify that the time you set is correctly displayed Testing Station Operation The station operation test is intended to verify that all of the solenoids have been correctly installed As you perform the test for each station verify that water is flowing by checking the controller the flow sensor or even by visually inspecting the sprinklers to check that water is flowing from them To test station operation 1 Press G until the Test screen is displayed Figure 13 2 Press and hold until the Test Sequence screen is displayed Figure 14 The controller automatically begins operating the master station and each of the stations in sequence for 60 seconds each The currently operating station is marked with the icon and the screen displays the number of seconds remaining for that station s operation test Figure 13 Test Screen F
12. g information Se Current program number w Current water flow amp Current time Press again to return to the main irrigation screen which displays the current irrigation program countdown In addition on the left side of the screen an icon indicates which screen you are currently viewing according to the list of screens printed on the unit Establishing Communication with the Server When setting up the G S I Controller for the first time establishing communication with the server automatically sets the controller clock Generally communication is established automatically as soon as the G S I Controller is activated However in situations where this does not occur you can manually establish communication with the server To manually establish communication Ze Press and simultaneously The fei icon flashes on the screen while the unit synchronizes with the server After the unit is synchronized the and fei icons flash alternatively as long as the controller is in communication mode When the upload download session is complete the controller automatically ends communication and the controller display returns to the Main screen To end communication manually ZG Press bk and simultaneously Communication immediately ends The controller display returns to the Main screen 12 Galcon G S I Controller Installation and User Guide Manually Setting the Controller Clock In order for the controller to corr
13. hing icon remains on the screen until the valve is restored to successful operation The next time the valve is scheduled to be opened the controller tries opening the valve again Locking and Unlocking the Screen The G S Controller enables you to lock the screen preventing people from editing the unit s programming until the screen is unlocked eeGalcon 19 G S I Controller Installation and User Guide To lock the screen BA as Press G and at the same time The screen is locked and displays To unlock the screen as Press G and at the same time The screen is unlocked and the unit can be programmed 2 G cCclcon Technical Specifications Se Transformer input 230V 50 Hz or 110V 60 Hz for American models amp Transformer output 24VAC 2 5 amp amp Station output 0 5 amps per station Se Maximum output 4 1 Master amp Electronic short circuit protection Se Non Volatile memory for program data Backup Batteries 4X1 5V a type Batteries operators globally Se Dimensions 10 5x24 5x25 5 CM Se Operating ambient temperature 10 C to 60 C 14 F to 140 F amp Cellular modem Quad band GSM modem integrated GPRS class 10 for operating in all GSM eecalcon 2 5 Warranty CH Home Professional Gardening Gardening LIMITED WARRANTY CERTIFICATE 1 Galcon shall for a limited period of 36 months from the retail purchase date of the original first purchaser the
14. igure 14 Test Sequence Screen You can optionally extend or shorten a station operation test as follows Se To extend or to shorten the operation test time of the current station press or respectively Se To close an operating station before its test time has elapsed and move to the next station press WW The icon moves according to your selection Se To end the test sequence completely press and simultaneously The controller closes all the stations eeGalcon 3 G S I Controller Installation and User Guide Creating an Irrigation Program A L Notes ge When locally creating the irrigation program e Stations always run in the order of their numbers e Youcan seta different duration for each station The cycle time start day and start time apply for the first station in the sequence As one station s irrigation duration ends the next station automatically begins Locally created irrigation programs continue operating even after you upload a detailed program from the G S Web User Interface they will both operate simultaneously If you want to end the locally created program you must cancel it in the G S Web User Interface explicitly or from the controller Setting Irrigation Program Durations Irrigation program duration also known as the run time can be defined for each station To set the irrigation program duration 1 Press G until the Duration screen is displayed Figure 15 2 Press
15. ors is calcon G S I Controller Installation and User Guide Fault Messages If a fault occurs in the system the controller screen displays the message FLt or FL and a fault number Table 1 Fault Numbers and Definitions Fault Indication Message Description FLt O Low flow fault FLt 1 High flow fault FLt 2 No water flow fault FLt 3 Uncontrolled water flow fault FL 11 Station definition fault FL 12 Irrigation program fault FL 13 Controller memory fault Canceling Fault Alerts To cancel an alert and remove the fault message from the screen Va Ka With the fault message displayed press and simultaneously General System Messages va K BA KA va K Flashing low battery icon When the backup battery is low a flashing battery icon appears on the display This indicates that the backup battery should be replaced AC Off If for any reason the controller stops receiving AC power from the main line a blinking AC icon is displayed While this is the case the controller can still be programed and manual communication will still be possible as long as backup battery power is available However valves cannot be opened and programs cannot be performed according to the schedule Valve short circuit In the event of a short circuit in a valve or one of its connections a icon flashes on the display over the relevant valve number and the word Shrt is displayed for few seconds The flas
16. r not based on breach of contract tort including negligence product liability or otherwise arising from the performance or non performance of any aspect of the Product or any part thereof All of the above whether or not Galcon and or the Customer shall have been made aware of the possibility of such loss In any event any liability which Galcon may have in connection with the Product and or this Warranty including without limitation in connection with and or resulting from the Product or any part thereof and the use thereof shall be limited to a total amount for all damages claims and causes of action in the aggregate equal to the consideration actually received by Galcon from the Customer for the Product The limitations shall apply whether the liability is based on contract tort Strict liability or any other theory This Warranty and the remedies set forth herein are exclusive and in lieu of all other warranties remedies and conditions whether oral written statutory express or implied Galcon specifically disclaims any and all statutory or implied warranties including without limitation warranties of merchantability and fitness for a particular purpose and warranties against hidden or latent defects The Customer shall be solely responsible for the selection use efficiency and suitability of the Product s The provisions of this Limited Warranty Certificate shall be interpreted and governed solely and exclusively pu
17. reof and or any failure to install and or use any Product in full compliance with Galcon s instructions ii other systems components devices technologies and or the integration interface thereof with any Product iii any part component which has been included installed in any Product not at Galcon s approval and or other than by Galcon iv any actual or attempted change repair interference of with any Product including any use handling of and or interference dealing with any code of any software included used in the Product other than by Galcon v any data information content which has been inserted included in a Product vi malfunction or damage resulting from accidents which occur during transit and or handling and or malfunction or damage due to fire earthquake flood lightning and or any other external disaster vii unforeseen accidents wear and tear or any other external factors beyond Galcon s reasonable control or to any Product installed repaired adjusted rebuilt modified changed or converted by any person including the Customer other than Galcon 5 In addition and without derogating from the provisions of this Warranty Galcon s warranty is conditioned upon the all of the following taking place i Customer s operating and maintaining the Product in accordance with Galcon s instructions ii Customer s not being in default of any payment obligation to the Galcon or its authorized dealer as relevant
18. rom the Controller The controller enables you to pause irrigation While a pause is in effect all irrigation programs currently in progress are paused and any new irrigation programs which were scheduled to start are not started While irrigation is paused in this way you can still perform station operation tests and establish communication with the server When the pause is ended and irrigation is resumed all irrigation programs continue according to the following rules e While paused programs are delayed until midnight As such if the pause is ended before midnight the programs resume where they left off and scheduled programs for that period will also run e Ifthe system pause condition ended after midnight all delayed and scheduled programs are canceled and will initiate irrigation according to their next scheduled timing To pause an irrigation program Se Press continuously until the message PA US is displayed on the screen This indicates that the irrigation is now paused The PA US message flashes on the screen until you resume irrigation To resume irrigation Se Press continuously until the Main screen is displayed Note the controller will react according to the paused rules also in the following occasions va K AC power off Rain sensor activation va Ky System Alerts The G S I Controller features various kinds of system alerts including fault messages and other problem indicat
19. rsuant to the laws of the State of Israel and no other law shall apply Any and all legal actions shall be litigated within the jurisdiction of the courts of Israel and no other jurisdiction shall apply 24 eGalcon
20. screen Figure 12 Main Screen Press to cycle through the following information displays on the Main screen Se Current time hh mm format Flow value currently detected by the flow sensor in m hr Notes Until the flow sensor is defined using the G S Web User Interface this screen does not display actual data When there is no water flow the flow value should be zero If it is not contact Galcon Support amp Current voltage of the controller s backup battery Se Last four digits of the controller unit s 16 digit serial number SS Current firmware version number e amp ecalicon G S I Controller Installation and User Guide The Main screen is the launching point for all other G S controller operations It displays the following information depending on the circumstances Ze By default Displays the current time hh mm format and a list indicating the number of irrigation stations which are currently connected to the controller Se During irrigation Displays a icon below the irrigation station in the list which is currently performing irrigation as well as the amount of time remaining until that irrigation process finishes lf more than one station is currently performing irrigation the icon is displayed for each of them In addition a A icon is displayed below one of those stations and the time displayed applies for that Station Optionally press to cycle through the followin
21. stallation and User Guide Figure 9 SIM Card Case 4 Slide the SIM card case cover to the side to open it as indicated by the arrow labeled OPEN see Figure 11 5 Open the cover and slide the SIM card into the grooves located on the inner part of the case cover Make sure that you have oriented the SIM card correctly Figure 10 SIM Card Insertion Orientation 6 Close the case cover 7 Hold the SIM card case cover down while you slide the cover to the side as indicated by the arrow labeled LOCK Figure 11 Figure 11 Correctly Inserted SIM Card 8 Swing the control panel back into place 9 Close and lock the controller cover io eGalcon On Site Controller Operation The Galcon G S I Controller is designed to run irrigation programs created using the online G S Web User Interface In addition however the G S I Controller includes a control panel which enables basic initial program creation The following sections outline how to set up the G S I Controller create a basic irrigation program and perform other irrigation and troubleshooting tasks AlL Note Programs defined from the G S I Controller control panel continue to operate until Ki you explicitly deactivate them from the G S Web User Interface application even if you upload a different program from the application Main Screen Features You can view information and monitor irrigation processes directly from the G S I Controller Main
22. t you label the input wires by function for future Le AS d reference eecalcon 7 G S I Controller Installation and User Guide Connecting AC Power T Warning When installing the AC unit power installation must be performed by a qualified electrical technician To connect AC power 1 Unlock and open the controller cover Figure 1 2 Swing out the control panel Figure 2 3 For the internal casing on the right side unscrew the two screws and open the casing Figure 3 4 Pullthe three electrical wires through the cable gland at the bottom of the controller 5 Connect the wires to the feed through terminal block The terminal block can be pulled out to be more easily accessed Connect hot to the brown wire natural to the blue wire and ground to the yellow wire Always use 1 2 conduit male adaptor when installing the AC wiring 6 Proceed to backup battery installation below Connecting Backup Batteries You must install backup batteries In the event of a power failure the batteries keep the controller functional including enabling the modem to send power failure alerts To connect a backup battery 1 Turn the battery compartment latch by 90 degrees and pull out the battery compartment Figure 8 Battery Compartment Removed 2 Insert four AA 1 5 Volt batteries not supplied as a backup power source into the battery compartment and connect them 3 Return the battery compartment and lock it in
23. tion For information about using the G S Web User Interface refer to the G S Web User Interface User Guide G S I Controller Models There are two models of the G S I Controller based on the type of power supply used 7 DC unit which supports either Alkaline or Lithium batteries va ZS AC unit This document describes the AC unit type sscalcor 2 Setting Up the G S I Controller Setting up the G S I Controller system includes the following tasks Va Se Installing the Controller see page 5 Va Se Establishing the Electrical Connections see page 6 L Installing the Controller The controller is designed to withstand outdoor installation conditions at a rating of IP65 However it is preferable to provide additional protection from the climate by installing it in a sheltered position Appropriate installation of the controller will ensure dependable operation throughout the years The controller can be installed in two ways E e Installation on a wall or in a control cupboard BA Va Se Installation on a metal pole of 1 to 1 diameter Installing on a Wall or in a Control Cupboard To install the controller on a wall or in a control cupboard 1 Unlock and open the controller cover Figure 1 2 Swing out the control panel Figure 2 3 For the internal casing on the right side unscrew the two screws and open the casing Figure 3 Mount the controller to the wall or to the
24. ure 5 Mounting Screw Holes DIMENSIONS EE 6 Figure 6 Inserting the Mounting Screws with Cover Cape eeh NEEN NEEN NEE EEN 6 Figure 72 Cone oner Kg en ln BOCKE E 7 Figure 8 Battery Compartment REMOVE occccccccccccce cece EEE EEE EEE E EEE E EEE E EEE E EEE E EAHA HEHE EERE EEE EERE EERE EEE EES 8 Figure 9 SIM Card Case EE 10 Fi g re 10 SIM Card Insertion Orientali M EE 10 Figure 1i Correctly Inserted SIM Car EE 10 PIGUES 222 Mali SeNCeM EE 11 Foe NSS MCSl SOKO RE 13 Figure 14 gt Test SEQUENCES SCE EE 13 Figure 15 Duration Screen Example EE 14 FOO LOF Cy Cle SC iS SU E 15 Figure 17 Twelve Hour Cycle Setting Example EE 15 Figure 18 Six Day Cycle Setting Exvample cee EERE EEE E EEE E EEE E EEE E EEE E EEE E EEE E EERE EEE EEE EERE 16 Figure 19 Start Day Screen Example EE 16 2 G cGOlcon 1 Introduction The Galcon G S I Controller is a controller which functions as the intermediary between central Galcon servers and the irrigation valves in the field Creating irrigation programs for the G S I Controller is primarily done from the G S Web User Interface However you can also create a simple irrigation program directly on the controller even before setting up the Web interface You can also perform manual irrigation direct from the controller This manual describes how to install the G S I Controller test to verify successful installation perform basic initial irrigation programming and perform manual valve irriga
Download Pdf Manuals
Related Search