User Manual
Contents
1. L AUDAC www audac eu Index Introduction Caution servicing User interface Login screen Main screen Zone settings Sound settings Test signals Settings screen Digital input selection Time settings Display configuration Address settings Password settings Factory settings Notes AUDAC 3 Introduction 7 Touchscreen display kit M2 The M2DIS is an optional display unit with touchscreen which can be installed internally in the front panel of the M2 Multi Media Digital audio mixer This unit consists of a 7 TFT display panel with a resolution of 800 x 480 px that is fitted with a resistive touchscreen panel It is controlled by a powerful 32 bit processor which communicates directly with the DSP processor This unit allows the user to operate the control functions of the matrix systems without any external equipment This can be useful when the system is installed in a technical room where no external control devices are within reach Touchscreen precautions e Tap the touchscreen gently Never use force e Don t use any sharp object to tap the touchscreen Don t use a pen but only use your fingertips or stylus especially meant for use with touchscreens e Keep the touchscreen dry and clean Don t use any abrasives or cleaning solutions to clean it Only clean it with a soft damp cloth AUDAC User interface 8 AUDAC R2Audio Matrix Password 8 AUDAC R2Audio Matrix A password should be en2. You can also select filters Save This option is only available if logged in as ADMINISTRATOR By pressing this button you can save the settings To make sure the changed zone settings are still effective after shutdown and restart of the M2 the Save button on the main screen of the M2 need to be pressed At the same time the volume and routing settings will be saved gt e 2 HM m Settings This option is only available if logged in as ADMINISTRATOR In the top right corner is a Setup button displayed After pressing this button you will be redirected to the configuration menu of the M2 Info Pressing the AUDAC logo will show the info screen LA AUDAC R2Audio Matrix AUDAC Multimedia Room Amplifier R2 Copyright 2009 2011 Contact AUDAC Belgium Website www audac eu LCD V1 1 DSP V3 9 This option is only available if logged in as ADMINISTRATOR By pressing the Settings button above a slider the Zone Settings screen is displayed In this window you can select an input channel for the selected zone 8 AUDAC R2Audio Matrix Zone 1 SETTINGS CINCH INPUTS WALL INPUTS FIBER INPUTS Input 1 WP In 1 Fbin1 input 2 WPin2 Fbin 2 Sound setting Input 3 WP In 3 Fbin 3 Test Signals Input 4 WP In 4 Fb in 4 Zone linking Input 5 WP in 5 Fo ins Input 6 WP In 6 Fbin6 Input selection Input 7 WP iIn7 Fbin7 Input 8 WP In8 Fbin8 Input channel selection The
3. of no activity The administrator has to log on again Push Logoff time to change the time e Limited control When enabled there is no logon screen At start up the main screen is shown The user can only change volume and mute For other functions the password will be asked e Keyboard Type 3 types of keyboard can be selected AZERTY QWERTY ABC e Screensaver 2 types can be selected Off Clock If Clock is selected after some time an analog clock is shown The time can be configured in Screensaver time e Update software With this button the firmware of the display unit will be updated not the firmware of the M2 The software can be updated by placing a USB memory stick in the USB port at the rear side of the display unit and holding the Update software button for 3 seconds After 3 seconds an update screen appears and the system starts updating When finished updating the display unit restarts and a login screen appears 18 AUDAC UPDATING SOFTWARE e Calibration If the touchscreen isn t working accurate it must be calibrated The calibration must be done by a stylus which is meant for use with touchscreens The cross shown in the diplay needs to be touched three times in a row to calibrate the touchscreen correctly To make an accurate calibration it should be touched exactly at the center position of the cross ATTENTION Don t use any sharp object to
4. Now click the Add button and everything will be saved For more information about this screen please refer to the M2 user manual Settings gt gt Paging Volume In this window the volume for all outputs can be set to a value you seem fit for paging ATDOGCIOING inniinn make SEE ait inertie AUDAC 1 For every output you can set the paging volume and choose if the relay for this ouput should be switched or not In this window you can preset 4 priority settings AV OTTE To LIL Re NTR SELE NER To do a priority setting first choose a channel on which the M2 will trigger your setting Now an input should be chosen You can select every output to which the input should be routed For every output it is possible to set volume and toggle relay position For more info about priority settings please refer to the M2 user manual In this window the time and date of the M2 can be set This can be done by selecting the values from a dropdown list 5 AUDAC R2Audio Matrix TIME SETTINGS Manua Month Da Hour Mir se Press Set Clock to set time and date This window configures the display unit screen not the M2 LA AUDAC R2Audio Matrix LCD CONFIGURATION Auto logoff Panel Brightne Logoff time The settings must be save by pressing the SAVE button The next items can be set e Panel brightness Sets the brightness of the backlight e Auto Logoff When enabled the system logs off after some time
5. ain Assign names to output This option is only available if logged in as ADMINISTRATOR For a better overview of all outputs every fader has a name The name of the output can be changed by pressing and holding the name for 2 seconds After 2 seconds a keyboard screen is displayed to change the name After changing the name press OK CE AUDAC R2Aucio Matrix Press the Save button and confirm to save the zone settings Input channel selection This option is available if logged in as ADMINISTRATOR or USER The desired input signal for an output can be selected by pressing the button below the output name A dropdown list shows 8 audio input signals together with the options Off and Other If logged in as administrator the list can be changed in the Quick menu settings screen This screen can be reached through Settings screen followed by output configuration screen 5 AUDAC R2ZAudio Matrix Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 8 Off Off Off Off Off Off Off Off Sr Settings Settings Settings Settings Settings Settings Settings Input 2 Input 3 Input 4 Input 5 Input 6 Input 7 Input 8 other Oo Output settings This option is only available if logged in as ADMINISTRATOR By pressing the Settings button above a slider the Output Settings screen is displayed In this window you can select all input channels to be mixed for the selected out
6. e to control the bass low tones which can be adjusted from 9 to 9 dB The other controls the treble high tones and can also be adjusted from 9 to 9 dB The settings screen is displayed by pressing the Setup button This button is always shown in the upper right corner of every window Only on Administrator level AUDAC R2Audio Matrix SETTINGS Digital Input LCD configuration In this window the next settings can be changed e Input configuration e Output configuration e Global scenes e Timer e Paging volume e Priority e System configuration e Fiber e Amplifier Bridging If you want to change some settings just click on the corresponding icon All settings will be saved automatically and are still effective after shutdown and restart of the M2 Settings gt gt Input Configuration First select the input which s settings should be changed PATIOS AN OSSE REE EEN S e A A ere Now a new screen appears which allows you to change this input s settings for Line and Mic For both Line and Mic you can set the gain apply ALC automatic Level Control apply several different filters and apply a 3 or 7 band equalizer by clicking the corresponding button Also the input can be muted toggled between mono and stereo and phantom power can be enabled ABEEIAIMG EE NE EA EEEE T gma laavast katke dadada hoiad ade For more info on these settings please refer to the M2 User Manual Settings gt gt Output Co
7. lost 5 AUDAC R2Audio Matrix RESTORE FACTORY SETTINGS CANCEL Click the OK button to reset the settings to factory default In this window the M2 s fiber connections can be managed optional Afbeelding issu For every of the eight fiber channels you can set an input to link with other M2 or R2 units or pass through to take an input from a M2 or R2 unit and pass it through to an other M2 or R2 unit For more info on fiber settings please refer to the M2 user manual Settings gt gt Amplifier Bridging In this window you can select one or more outputs to be bridged Albeeldind am ema ee en Select the output channels you want to bridge Bridging an output will result in a mono output with double power AUDAC 25 Notes 2 AUDAC Notes AUDAC 7 Notes 2 AUDAC
8. n address with a higher value 9 AUDAC R2Audio Matrix R2 ADDRESS R2 Address Co Click the OK button to confirm the address settings In this window the passwords for the M2 can be changed 8 AUDAC R2Audio Matrix PASSWORD SETTINGS Change admin password id Admin Password New Admin Password Retype Admin Password There are two different password levels Administrator level which has full access to all functions and User level which has only access to the basic functions On the left side of the window the settings for the Administrator password can be changed while on the right side the settings for the User password can be changed For changing the password enter the old password in the provided field and enter the new password twice in the provided fields After this all is completed push the OK button When the old password is correct and the new password filled in both fields match the old password will be changed into the new password The factory default password for Administrator is M2 and for User is user If the new password is left blank the user must not log in NOTE Be careful with leaving the admin password blank as everybody has access to the settings BE CAREFULL to press this button It will recall the ORIGINAL factory settings It does not recall the previously saved settings but it recalls the original factory setting and the previous made settings will be
9. nfiguration First select the Output which s settings should be changed fat arte Tre Ty Te isamaa dt Now a new screen appears which allows you to change this output s settings Following options can be adjusted or applied set volume apply several different filters apply a 3 or 7 band equalizer set quick menu settings set output linking settings set talkover settings by clicking the corresponding button Also the output can be toggled between mono and stereo toggled between Single ended and Balanced antiphase can be enabled and you can set a delay time for the output Afbeeldings raen ennemi a eee niente For more info on these settings please refer to the M2 User Manual 4 AUDAC Settings gt gt Global scene In this window global scenes can be made or adjusted Abe e ententes T user een As you can see you can set an input and volume for every output a trigger can also be set When the trigger accurs then this global scene will be enforced allowing you to set global scenes for all kinds of things from commercial messages to the fire alarm To keep things clear you can give each of the eight scenes a name Settings gt gt Timer settings In this window you can add and adjust timers AIDGCIOING TU To create or adjust timers first pick the action that needs to happen when the timerevent takes place Adjust the variables of this action to your desires and specify a day or date when the action needs to be executed
10. screen gives an overview of all input channels that can be patched to the output zone You can select M2 inputs Wall panel inputs Fiber inputs and Line inputs e f no input is needed click the All off button e The M2 inputs are shown as default Here you can select the inputs you want to mix e Click the Wall panel inputs button to select wall panel inputs e Click the Fiber inputs button to select Fiber inputs e Click the Line inputs button to select Line inputs e To save click the apply scene or save as scene button The M2 has an internal digital signal generator which can generate white noise pink noise and sinusoidal signals with a selectable frequency Each of those signals can be patched to any output zone 5 AUDAC R2Audio Matrix Zone 1 TEST SIGNALS Frequency 1000 Hz When one of the test signals is selected Other will appear in the Input Selection box on the main screen e Select white noise to route white noise to the output zone e Select pink noise to route pink noise to the output zone e Select Sine Generator to route a sine wave to the output zone The frequency of the sine wave can be changed by the up and down arrows In this screen you can control the value of bass and treble for this output 5 AUDAC R2Audio Matrix Zone 1 TEST SIGNALS Frequency 1000 Hz This screen shows two faders On
11. tap the touchscreen Don t use a pen but only use your fingertips or stylus especially meant for use with touchscreens The use of sharp objects can cause permanent damage to the touchscreen e Test M2DIS In this window the complete functionality of the display unit can be tested 2 AUDAC 5 AUDAC R2Audio Matrix REAL TIME CLO COMMUNICATION EEPROM USB Update software The REAL TIME CLOCK indicator must be green The COMMUNICATION indicator must be green The EEPROM indicator must be green When a USB memory stick is inserted to the USB port at the back side of the display unit this indicator should also be green The dimming of the backlight can be tested by moving the slider The touchscreen can be tested by making a drawing in the white field Use the Clear button to erase the field Use the Update software button to update the software of M2DIS Use the Calibration button to calibrate the touchscreen Use the BACK to return back to the previous screen In this menu the address of the M2 can be set This address default is 001 and is selectable between 001 and 999 When only one M2 is available the default address can be left to its default value When two or more M2 s are cascaded through the fibre interconnection bus they need to have a unique address The first M2 starts with address 001 and every subsequent M2 should be assigned a
12. tered to get access to the M2 amplifier There are two different access levels administrator level and user level If you log in with the administrator password you get access to all functions and configuration options The factory default password for administrator access is M2 When you log in with the user password you only get access to the basic functions of the main screen such as changing the volume and changing the routing for a particular output zone The factory default password for user access is user After pressing the text field a Keyboard screen is displayed and you can enter the password After the password is entered press the OK button and you will be redirected to the main screen of the M2 interface NOTE The passwords can be changed in the Settings gt gt Password settings menu Only administrator 6 AUDAC The main screen displays all 8 outputs of the M2 with fader volume controls 8 AUDAC R2Audio Matrix Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 7 Zone 8 of on on oft oft oft Off Settings Settings Settings Settings Settings Settings Settings Settings Volume control The volume of each output can be changed by moving the fader At the bottom is a Mute button to mute the volume of the corresponding output If the out is muted the mute button is Red If the zone is unmuted the mute button is Green The mute can be toggled from mute to unmuted by pressing it ag
Download Pdf Manuals
Related Search