SR-2809&SR-1005XX RGB Remote controller User Manual
Contents
1. 5 6 Brightness adjustment Under the static color status or color changing status you can adjust the brightness by press button B and pressing button 8 to increase the brightness The brightness is divided into 8 levels the minimum is 10 and the maximum is 100 5 7 Changing speed adjustment Under color changing mode you can slow down the changing speed by pressing button S or speed up changing speed by pressing button 10 speed levels in total are available 6 Expanded Usage 6 1 Color changing for multiple same ID receivers under same mode One receiver of the sender can be learned unrestricted by multiple receivers a receiver can be only defined one ID No from one sender If one of senders is learned by several receivers all these receivers will share the same ID No When all these receivers are changing color at the same time to ensure long time changing in order one of the receivers from this groups is needed to be set as Master receiver and other receivers need to be set as Slave receivers How to set Master receiver and Slave receiver please refer to 4 2 Receiver learning ID code Notice Only one receiver Master can be set amont a group of receivers otherwise it may cause chaotic phenomena When Master receiver is set this group receivers are changing color at same time synchronized signal will be emited so as to ensure this group receiver will be in order no matter how long the color changes and keep changing forev2. SR 2809 amp SR 1005XX RGB Remote controller User Manual Receiver SR 1005TA Receiver SR 1005FA Product introduction RF Touch RGB remote controller is a wireless color controlling system that consists of a sender and a receiver or several receivers Using RF Touch RGB remote controller you can get whatever color you want you can choose any color to adjust so as to mix more than 100 million kinds of colors With built in kinds of color changing mode you can easily switch color changing modes and adjust speed and brightness Function Pause enables RGB LED to stay at your favorite color under the situation of color changing mode which operation is simple but functional There are three working frequencies for option 434MHZ 868MHZ or 915MHZ which are suitable for Europe Americas and all global market demands All products completely comply with European CE regulations and American FCC regulations 2 Performance Parameter 2 1 Sender model SR 2809 Working frequency 434MHZ 868MHZ 915MHZ optional 2 2 Receiver model SR 1005TA SR 1005FA SR 1005FA3 SR 1005FA7 Input Voltage 12 36VDC Output Voltage 12 36VDC Input Current 3CHx3A max SR 1005TA 3CHx5A max SR 1005FA 3CHx350mA SR 1005FA3 3CHx700mMA SR 1005FA7 Output power 3CHx 36 108W max SR 1005TA 3CHx 60 180W max SR 1005FA 3CHx 4 2 12 6W SR 1005FA3 3CHx 8 4 25 2W SR 1005FA7 Working Frequency 434MHZ 868MHZ 915MHZ optional 3 Compon
3. ents description 3 1 Sender model SR 2809 Working status indicator the sender is in dormant status when the indicator is off The sender is under working when the indicator is flashing rapidly If the indicator continues flashing at the frequency of 1 second it indicates that the sender batteries low and needs to be recharged S Slow down the speed when color is changing S Speed up when color is changing P Multifunction button used for selecting ll Pause B Brightness down B Brightness up 9 Multifunction button used for turn ON OFF and CW WW NW output 1 2 Figure 1 2 is for selecting receiver s ID and ID itself to turn ON OFF Touch wheel for selecting R G B colors m left indicator will be on when charging middle indicator is for reset switch right one is for USB socket 4 Wiring diagram RGB color changing LED light arer w Eg J c E SR 1005FA Ermm EASY RGB CONTROLLER c S PRI ao Uin 12 36VDC mi 2 Power Supply Input 12 36VDC lin 15 8A SEC e mehr ea 2 36 VDC tc 75 C ot A a CEORoHS A 110 240V 5 Basic Usage 5 1 Install battery Initial using RF Touch RGB remote controller Needs remote control charging 5 2 Receiver learning ID Initial using RF Touch RGB remo
4. er For example 10 receivers are learned tobe ID 1 these 10 receivers will change according to one mode in order to avoid chaos of working units after along time one of the receivers is needed to be set as Master the Master will launch synchronized signal when color is changing thus ensure this group of receivers are in good order no matter how long the color is changing 6 2 Usage of ON OFF W 6 2 1 Press of ON OFF button IW for turning ON OFF receiver 6 2 2 Press ON OFF button f for more than 2 seconds it can reveal white light output each channel is 100 output 6 3 The usage of number button 1 2 6 3 1 Press on number button for choosing the corresponding receiver E g to adjust the brightness of receiver 1 you need to press 1 button 1 then press button 8 or button B to adjust its brightness 6 3 2 Pressing number button can turn on Off the corresponding single receiver E g If you need to turn off receiver 1 press button 1 more than 2 seconds if you need turn it on again please press button 1 again for more than 2 seconds Notice If you turn off the extension by pressing the corresponding number button you must turn on this receiver in the same way The receiver can not be switched on through button ON OFF 7 Symptoms and solutions 7 1 The Receiver cannot be learned to the sender Analysis 1 Exceed learning time every learning time is 5Seconds only 2 Sender is under dormancy status solution 1 Press recei
5. r more than 5 seconds when learning indicator is off then the learned ID is deleted If you need the receiver learn anew ID repeat the operation of 4 2 Receiver learning ID 5 4 Choose color by touching color wheel After the receiver learned the ID you can change each receiver s color by touching color wheel If you want to change the color of receiver NO 1 Press button 1 then make rotating touch on color wheel Ody your figures at this time the color of receiver No 1 will be changed constantly when your favorite color appears stop rotating and leave the color wheel If you need change color of several receivers at the same just choose a number for these several receivers first then touch color disc For example change color for receivers NO 1 2 at the same time you need press number 1 to 2 button 1 2 first then touch the color wheel 5 5 Choose color changing mode Selecting the mode button receiver change colors there is 1 color changing mode If you want one or several receivers under color changing mode press number button 1 2 and choose receiver number then press button again press of button W receiver will pause change the receiver will be paused it will stay at one color Press button ll again receiver will continue change The receiver will be at one of static colors by touching the color wheel in color changing modes Then press button receiver will be changed from start
6. te controller must learn the ID of the receiver the purpose of learning ID code is to make a certain receiver which can correspond the sender The method of Receiver learning ID is as follows press the ID learning button on the sender the ID learning indicator is on then press one of the number button 1 2 onthe sender press the number that you want this receiver to be E g If you want this receiver to be No 1 please press button 1 first then touch the wheel or you can press any functional button on the sender such as B B OH s s etc to transmit signal to the Sender after Receiver receives the signal from the sender the indicator will flash a few times and then turns off then receiver ID is activated If the ID activation is failed at the first time please repeat the previous procedures Attention The receiver ID learned by touching color wheel is different from the reciever that learned by pressing function button B B W s 6 The receiver ID learned by touching color wheel that we define it as SLAVE receiver the receiver ID learned by pressing function button B B W Is S that we define itas MASTER receiver The purpose of learning these two kinds of receivers is to ensure the receivers and color changing synchronously to avoid the color changing out of order This point will be noted later 5 3 Delete ID and ID re learning If you need to delete the ID learned in the receiver press ID learning button fo
7. ver learning button LED indicator is ON press the number button before led indicator is OFF then press function button or touch color wheel 2 Press On Off to make the sender under working status 7 2 The sender cannot control the receiver Analysis 1 Receiver isn t learned to the sender 2 The receiver isn t learned to the sender correctly 3 Remote distance is out of range 4 Incorrect receiver solution 1 To learn the receiver by the sender 2 When receiver is learned to the sender press number button first then press function button or touch color wheel 3 Shorten the remote distance 4 Choose correct receiver ID 7 3 Color changing isn t synchronized Analysis 1 MASTER receiver isn t set 2 More than two MASTER receivers are set solution 1 Reset a new MASTER receiver 2 Relearn all the receivers with one Master receiver 7 4 Wrong color Analysis Wrong connection of RGB W electric wires solution Reconnect RGB W electric wires 7 5 LED flashing Analysis the power is not enough solution Change a higher power supply 8 Precautions 8 1 Don t fall the sender from a high place or don t squeeze it 8 2 Please replace new batteries if there is a warning indicator of insufficient power otherwise it would cause damage to the sender 8 3 Receiver is non waterproof not for outdoor use
Download Pdf Manuals
Related Search