Home

S1100w User Manual.book

1. m Subnet mask 255 255 0 0 m Gateway 169 254 The portion is based on the MAC address of the device A device is in APIPA mode m The first time it boots up m After receiving a duplicate IP address m After a factory reset When the DHCP server does not have any available IP addresses DHCP configuration is disabled m After a firmware upgrade m After a factory reset 66 Verint Video Solutions DTE and DCE Connections Before connecting a Nextiva edge device to other serial equipment you need to determine if they are DTE data terminal equipment or DCE data communication equipment Here are examples of both equipment types m DCE Nextiva edge devices modems m DTE Computers switches multiplexers cameras keyboards Verint Video Solutions 67 D DTE and DCE Connections You need to know the equipment type of the other serial device to connect it correctly to the S1100w device which is a DCE In the following descriptions m Voltage is measured when no data is transferred on the Rx and Tx pins m X volts represents a negative voltage value Data Terminal Equipment DTE modules have the following electrical level setup Pin number Signal Measured voltage 3 Tx X volts 2 Rx 0 volt gt o Tx er Rx C ins Ground 0 volt measured for X volts measured the Rx pin for the Tx pin 68 Verint Video Solutions S1100w User Manual Data Communication Equ
2. Compliance To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the effective isotropic radiated power EIRP is not more than that required for successful communication Note The S1100w devices require professional installation They should be installed in a location that would prevent the general population from approaching from 3 feet 1 meter of the radiating element USA This device complies with part 15 of the FCC Federal Communications Commission rules see http www fcc gov Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation of the device This equipment has been tested and found to comply with the limits for Class B Digital Device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in residential installation This equipment generates and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment
3. channel RF automatic selection with DFS 12 available 6 selecting the location 52 113 Index channel RF cont d selecting in the CLI 50 characteristics of the device 2 CLI command line interface access with SConfigurator 42 access with Telnet 71 main menu 43 menus 44 55 timeout 43 client boot sequence with DFS 12 communication with master 27 maximum number in a cell 11 colocated cell 13 17 COM port 42 command line interface See CLI command line interface communication between S3100 and S1100w 27 compatibility of firmware versions 9 compliance 119 computer requirements 26 configuration alarm 34 36 audio 34 36 camera data port 2 default 37 54 57 device 25 27 1 0 34 36 order in the wireless cell 10 connection to a camera losing 37 DCE DTE 67 point to point 28 power iii 25 RS 232 34 serial 25 32 34 connectors on the CAB9P cable 24 console SConfigurator 42 constraints in Europe 11 12 15 17 contact between two masters 15 country available frequency bands 6 selecting in the CLI 51 114 D data throughput 11 DB 9 connector 24 34 DCE data communication equipment 67 default configuration 37 54 57 detection motion See motion detection DFS Dynamic Frequency Selection boot sequence 12 defined 6 setups in Europe 15 17 DHCP Dynamic Host Configuration Protocol 47 65 distance between antennas 13 77 82 between antennas and persons 21 between colocated devices 13 77 82 dome
4. 65 Appendix D DTE and DCE Connections unraranananan n 67 Appendix E CLI with Telnet ns 71 Appendix F Surge Protection mmmmenesens 75 vi Verint Video Solutions S1100w User Manual Appendix G Separation Between Devices Using Adjacent Channels ns nsnssssssssnenenenenenennnnnnnnne 77 Appendix H Motion Track ssnensnsennnse 83 Motion Detection Processing 84 Physical Connections uzsr sanneen nenn nenne nenne nenn nennen 84 Configuring the Dedicated Serial Port 85 Establishing a Connection uusesererenannnne nenn nennen nennen 86 Configuring the DVMD Module 89 Status Information sissi naii i aaa 90 Fil s Settings sn me sen te aden a en ana 91 Display Settings siseasi srutsrasuss a innsin ainia cree 92 E A E E 93 Sensitivity SettingS sissi dessertir ess puita ok iie 95 Target Settings caa ara ke ii 96 Marget SIZE oson aa Neea a Terme eE RAK men Na 98 Appendix I Technical Specifications 101 Glossary unuauanananananununununnnnnnanananununununnnnnnananananununnnnnnn 105 Index unuauananananananununununnnnnnanananunununnnnnnunananananunununnnnn 113 Compliance uuuuununununnnnananananananunununnananananananunununnn nen 119 Verint Video Solutions vii Viii Verint Video Solutions Preface The S1100w User Manual presents the information and procedures for inst
5. To do so you must connect the earth referenced terminal of the equipment to the same AC terminal as the black wire of the devices Failing to do so will short out the AC power supply a Sp a Sr a ls ao A 4 Black Red Black Red Black Red ph Third party equipment Isolated 24V AC AC main Verint Video Solutions iii Verint Video Solutions Contents Preface REPREREFERFOEPERTEPERPREFRFESPEEERPRERESEOPFESFERFEUHEESTECTTEFITRETER ix Who Should Read this Manual cccccceeseceeseeeeseeeeseeeees X How to Use this Manual nun nn x Contents issues diamants agente an nen nen x CONVENTIONS u tiie vader an anna nahe eave passat xii Related Documentation cccccceeceeeeeeveeeeeeeeeeuaeens xii Related Nextiva Products ccccccccesseeeeeeeevseeeeegeeesanens xiii ADOUC US A ann arte RS Te vada ube dans tetas xiii Warranty naron men ans cane Geen dean ans na Flanke aa xiv Chapter 1 OvervieW nununuanananananunununnnunnnnananananunanannnnnnn 1 About the S1100W nain aa aa a a aan a 2 SECUNIEV ee tien ondes than due ad aaa ee 2 VIGGO a EREA TAN ee A a rennen 2 Shipment un nenn 3 Casing Description nen anna 4 Chapter 2 a System and RF Planning zusuanannnununnnnnnnnn 5 Frequency Bands and Channels e eeeeeeeeeeeee teens 6 2 4 GHZ Ban ann
6. including Japan Compare with PAL NTP Network Time Protocol A protocol designed to synchronize the clocks of devices over a network OSD on screen display Status information displayed on the video monitor connected to a receiver edge device PAL Phase Alternation by Line A television signal standard 625 lines 50 Hz 220V primary power used in the United Kingdom much of western Europe several South American countries some Middle East and Asian countries several African countries Australia New Zealand and other Pacific island countries Compare with NTSC PTL push to listen In a two way system the communication mode in which the listener must push a button while listening PTT push to talk In a two way system the communication mode in which the talker must push a button while talking PTZ Camera pan tilt zoom An electronic camera that can be rotated left right up or down as well as zoomed in to get a magnified view of an object or area A PTZ camera monitors a larger area than a fixed camera Receiver A device converting a digital video signal into an analog form Also called decoder Repeater A range extender for wireless links The Nextiva repeater is made up of two S3100 bridges 108 Verint Video Solutions S1100w User Manual RF radio frequency Any frequency within the electromagnetic spectrum associated with radio wave propagation When a modulated signal is supplied to an antenna an electromag
7. 5 28 153 5 765 60 5 30 157 5 785 64 5 32 161 5 805 165 5 825 In Europe the 11 non overlapping channels for indoor or outdoor use are Channel Frequency GHz Channel Frequency GHz 100 5 50 124 5 62 104 5 52 128 5 64 108 5 54 132 5 66 112 5 56 136 5 68 116 5 58 140 5 70 120 5 60 Wireless Cells A wireless network is designed such that information can travel back and forth between two points without the need for wires In the case of the S1100w this information consists of digitized video audio and PTZ data sent to and from the wired network via an outdoor wireless bridge the Nextiva S3100 device Verint Video Solutions 7 2 System and RF Planning A wireless cell consists of a group of wireless devices that communicate together on the same frequency channel and that share the same wireless passkey described on page 49 For example You can colocate many wireless cells if you respect certain conditions see page 13 System Planning When installing many wireless systems in the same area you have to carefully plan their positions in order to prevent radio interference and select the appropriate antennas The grouping of devices in each wireless cell is determined by their respective locations with respect to one another and by the available outdoor wireless bridges As a rule of thumb there should be a clear RF line of
8. Black Yellow 3 Lo olele O47 N C 5 TxD Tx Yellow Black to 1 0 8 N C 6 VG Black Blue ro N C 4 5 CAM4 MON Blue Black RARES Pa paca PNG A SG SC g RxD Rx Black Green i Serial data terminal block Female DB 9 jack 9 SG Brown Black pair Female mating side 0 Female BNC jack video in out where m The RS 422 485 signal terminology is enclosed in parentheses m The other wire of each twisted pair is enclosed in square brackets m N C means not connected Based on the pinout the wiring scheme for a connection to a computer is Cable Computer Signal name Wire pair Wire color Signal name CTS green black green not connected RxD black RxD TxD yellow black yellow TxD RTS black not connected SG brown black brown SG SG black SG Verint Video Solutions 63 B Cable Descriptions CAB8P The CAB8P cable is used for audio and alarms The mating side view of the cable is Alarm In1 Audio Ground Here is its pinout 4 Alarm Out A Red Black Alarm Out 2 Alarm In 2 PTT White Black Alarm In 2 3 Audio In Green Black e Audio In 4 Audio Ground Black Green Black Blue 5 Audio Out Blue Black Audio Out 6 Alarm In 1 Yellow Black 7 Alarm Out B Black Red 8 Alarm Ground Black Yellow Black White 4 s Alarm In 1 Female mating side where m The other wire of the tw
9. F 7 C is required to protect the equipment If required install an external antenna see page 31 Apply silicone grease on the mating connector of the CAB9P cable and on the main connector of the device For the detailed procedure refer to the leaflet shipped with the cable Connect the CAB9P cable to the S1100w device To properly install the cable connector on the device you have to turn until you feel a positive click Plug the BNC video connector of the CAB9P cable on the camera Perform the serial connection to the camera if required see page 32 If you are using a junction box route all wires to it first then route the wires from the box to the target device 10 Power up the transmitter 30 Verint Video Solutions S1100w User Manual Installing an Antenna If you bought a high gain antenna install it after the S1100w is in place The antennas provided by Verint Video Solutions are designed to be mounted on a mast or pole of 2 3 inch 5 7 5 centimeter diameter To install an external antenna 1 Install the antenna above the S1100w device If you bought your antenna from Verint Video Solutions use the supplied pole mount bracket Screw the SMA connector of the antenna cable to the S1100w antenna port and tighten it with a 0 25 inch 0 6 centimeter wrench Warning Do not over tighten to avoid damaging the connector The recommended torque is 8 Ib in 100 N cm You could use a cali
10. GHz OFDM m 802 11g 2 4 GHz OFDM Channel The RF channel used by the S1100w device is determined by its outdoor wireless bridge However in a non DFS context you can specify an initial value for the roaming process by which the S1100w will find its bridge be aware that this initial channel may not be the one used by the bridge Tx Bit Rate The transmission bit rate is the data rate at which the device operates A high bit rate reduces the effective distance between two functional devices When an S1100w connects to its master for the first time it automatically receives the best possible value the Auto value with a default RF margin set to 15 dB to change the margin see page 52 Once the device is operating properly Verint Video Solutions strongly recommends to change the configured bit rate from Auto to the actual bit rate of the connection This way the wireless communication will be more stable in the presence of changing atmospheric conditions or other RF interferers To know the actual bit rate of the connection look in the Advanced gt Communication Status and Statistics gt Wireless Status menu If the quality of the RF link degrades severely the actual bit rate could be lower that the manually configured one The available bit rates for the S1100w device are 6 9 12 18 24 36 48 and 54 Mbps Antenna Gain If you enter the gain of the antenna you connect to the device the S1100w will be able to autom
11. HEHE IE E DE JE JE HE JE E JE JE JE JE DE E JE JE JE JE HE HE FE JE JE JE JE JE HE FE JE JE JE JE JE HE JE JE JE JE JE HEE IE 1 Serial Port 2 Access Management 3 System Status 4 Network 5 Ethernet Communication 6 Advanced Commands s Save Settings r Reboot Systen 1 Load Default Configuration q Quit HEHE IEE E JE HE HE IE DE DE DE JE DE JE HE DE DE DE JE DE DE DE DE DE DE DE DE DE JE FE JE DE DE DE DE DE JE JE JE JE DE DE DE JE JE JE DE JE IE DE JE JE DE IEE IEE Command 14 The CLI has a timeout that is triggered after three minutes of inactivity When the timeout occurs o You lose access to the command line o The Thank you for using the Verint Video Solutions CLI message appears at the command line o The Verint Console window becomes disabled o The Disconnect button switches to Connect 4 To reactivate the CLI after a timeout click Connect 72 Verint Video Solutions S1100w User Manual 5 To work through the CLI menu structure follow these guidelines o To execute a command or open a menu type in the corresponding letter or number then press Enter o To return to the previous menu enter p 6 To end the CLI work session a Save the settings by entering s at the main menu then pressing Enter b Exit the CLI by entering q at the main menu then pressing Enter Depending on the changed settings the device may perform a soft boot c Close the Ver
12. Numbers 172 16 0 25 5005 Local Connection C Local COM Port Timeout 200 TX Delay 5 Module Address Cancel CAMERA0001151100w 1IFFOISNET Localhostunknown In the Module Description field enter a meaningful free format text identifying the DVMD module In the Channel ID field select a number for the DVMD module In a large system you should provide a unique value to each module to easily distinguish it from the others The Channel ID value is displayed under the CameralD column in the connection table Set the communication type to Network as opposed to a local connection In the Type field select UDPLink In the IP Address field enter the IP address of the S1100w MT device In the Port Numbers field enter 5005 the same value as in the Remote Port and Local Port parameters in the CLI as illustrated on page 85 10 In the Module Address field ensure that the value is FFO Verint Video Solutions 87 H Motion Track 11 Click OK The Camera Types window appears Camera Types xj Camera Type Fixed Camera gt Video Type NTSC Cancel PTZ Address jo PTZ Baud Rate 12 In the Camera Type field select Fixed Camera 13 In the Video Type field select the video standard used 14 Click OK The new connection should appear in the connection table fiz Module ManagerNET i je O x CAMERA0001 1100w 1 If a timeout error
13. Video Solutions S1100w User Manual Line Driver By default your device automatically detects the electrical line interface of the serial port RS 232 or RS 422 485 However if your device cannot properly detect the electrical level for instance when there is too much noise on the line or too much signal attenuation due to excessive cable length you can use the line driver setting to force its electrical line interface Here are the possible line driver settings where a indicates that the auto detection mode is activated and f that the line driver is forced Setting Description 232f d RS 232 auto detected full duplex operation 232f f RS 232 forced full duplex operation 485f d RS 422 485 auto detected 4 wire full duplex RS 485 operation 485h d RS 422 485 auto detected 2 wire half duplex RS 485 operation 485h f RS 422 485 forced 2 wire half duplex RS 485 operation 485f f RS 422 485 forced 4 wire full duplex RS 485 operation 422f d RS 422 485 auto detected 4 wire full duplex RS 422 operation 422f f RS 422 485 forced 4 wire full duplex RS 422 operation Warning If the line driver is forced to an RS 422 485 setting you will not have access to the CLI unless you use an RS 485 to RS 232 converter or perform a hardware reset described on page 37 RS 422 485 Operating Mode The operating mode setting enables you to establish the way your RS 422 485 serial equipment will interf
14. a RAR sana nadie nas ee 6 5 GHZ Ban Gl sc aaa na area rares mn dies 6 Wireless Cellst 2 s fn nan ood Saka weal Re AE 7 System Planning anne nat tenes 8 Point to Multipoint Application 9 Compatibility Issues 2u2sssreren anne nenn nenn n nennen en 9 Video Bit Rate and Data Throughput 11 TPE u ee bee oedaceds 11 DRS E een nat done ale dot ae ne Fi 12 Colocated Eells u en nn 13 Distance Limitations zeesesnnennnn nennen nn nn nennen nn nenne 13 5 GHz Band in North America and 2 4 GHZ 13 5 GHz Band in Europe euauaesenenennnnnennnnnen nennen nn 15 RFPlanning 2 2 en eg 17 Location Evaluation ss 17 Antenna Requirements 8 19 Interference u een 20 RF Exposure Considerations 21 Verint Video Solutions v Contents Chapter 3 Configuring and Installing the Device 23 Cable for Power Video and Serial Data 24 Configuring the Wireless System 25 Computer Requirements euussersennnnnnnnnnnnnn nen nennen 26 Setting Parameters ausennnnunnennnnnnnennnnnnnen nn nenn 26 Point to Point Connection uusersennnnennnnnn nennen nennen 28 Installing the Wireless System 2ererannnnnnennn nenn nn 29 Installing the Transmitter s usererennnan nenn nennen nn 29 Installing an Antenna ezererenseeenenn
15. connection 33 DSCP Differentiated Service Code Points 37 DTE data terminal equipment 67 duplex audio 35 duplicate IP address 26 DVMD module for motion track 83 99 Dynamic Frequency Selection See DFS Dynamic Frequency Selection E EIRP 19 electrical line interface 45 emitting power See transmission power enclosure of the device 4 equipment list 3 ETSI European Telecommunications Standards Institute 6 Verint Video Solutions Europe colocation in the 5 GHz band 15 17 DFS context 6 12 TPC context 6 11 evaluating the location 17 event See alarm exposure RF 21 external antenna See antenna F factory default configuration 37 54 57 features of the device 2 firmware update preventing 47 without losing devices 10 firmware version compatibility between devices 9 displayed 53 first Fresnel zone 18 forcing the electrical line interface 45 frame rate 2 frequency band available 6 distance limitations 77 82 selecting in the CLI 50 frequency channel automatic selection with DFS 12 available 6 selecting the location 52 selecting in the CLI 50 Fresnel zone 18 full duplex audio 35 G gain of an antenna 19 50 gateway 48 H hardware reset 37 57 Verint Video Solutions S1100w User Manual I I O alarm or audio 34 36 identifying a device 54 indoor outdoor RF regulation 52 input alarm or audio 34 36 installation antenna 31 device 29 30 integrated antenna 3 interference RF
16. in a surge prone environment This protection will benefit both the camera and the device deviceExcellent international sources for external surge protection equipment and general surge and lightning protection information are m Polyphaser Corporation www polyphaser com m Citel inc www citelprotection com m Transtector www transtector com For the curious mind a surge protector helps to clamp the surge to safe levels and divert its energy to the earthing point preventing device damage Experienced installers know that an effective surge protection must be installed with proper earthing and grounding 76 Verint Video Solutions Separation Between Devices Using Adjacent Channels Verint Video Solutions G Separation Between Devices Using Adjacent Channels If using adjacent frequency channels in a non DFS environment you should respect guidelines relative to the minimum separation between device antennas The guidelines apply to the S1100 S1100w and S3100 devices In the 2 4 GHz band the adjacent channel term applies only to the three non overlapping channels 1 6 and 11 The presented figures represent worse case scenarios By respecting them you can assume that there will not be radio interference between the devices Three physical setups are covered Side by side 3 er T VERINT 7 SmartSight Back to back op VERINT VERINT A SmartSight SmartSight The
17. minimum separation between devices using adjacent channels are Setup 5 GHz 13 dBi antenna 2 4 GHz 8 5 dBi antenna with 40 beam width with 60 beam width Side by side 43 feet 13m 55 8 feet 17m On top 13 feet 4m 6 2 feet 1 9m Back to back 7 8 feet 2 4m 15 7 feet 4 8m If you are using other antennas with narrower beam widths the distances may be reduced For assistance contact the Verint Video Solutions project engineering group 78 Verint Video Solutions S1100w User Manual To help you plan your systems here are installation scenarios that respect the limitations These scenarios include the frequency band and channel m Using only 5 GHz channels all on the same side of a building 5 8GHz 5 3GHz 5 8GHz 5 3GHz 5 8GHz 5 3GHz 5 8GHz 5 3GHz 5 8 GHz 165 56 157 64 149 52 161 60 153 10 75 feet les feet 13m 3 25m each Notice that the devices using the adjacent channels 52 and 56 are separated by the prescribed 43 feet 13m However you can intersperse other devices in between as long as they do not use adjacent channels This way you can increase the device density without encountering interference problems m Using 5 GHz and 2 4 GHz channels all on the same side of a building 5 8 GHz 5 8 GHz 5 8 GHz 5 3 GHz 5 3 GHz 2 4 GHz 2 4GHz 165 5 3GHz 157 5 3GHz 149 24CHz 52 58GHz 60 5 8GHz 1 6 56 64 11 161 153 9 2 f
18. series proposes two receivers with one and four video outputs S1600e The high resolution wired edge device receiver and transmitter providing point to point analog extension with web access S1700e Series The series of wired video transmitters designed for video monitoring and surveillance over IP networks offering DVD quality video and power over Ethernet The transmitter in the series offers one video input and web access Verint Video Solutions 109 Glossary S1708e Series The series of wired video transmitters designed for a variety of video monitoring and surveillance applications in which a high concentration of cameras terminates within the same area The transmitters in the series offer 8 12 or 24 video inputs S2500e The MPEG 4 compliant professional IP camera integrating a video camera and an Ethernet encoder in the same compact enclosure 3100 The outdoor wireless digital video bridging device It has many uses including linking edge devices wireless or wired to an Ethernet LAN and acting as a range extender SConfigurator A proprietary graphical program used to configure and update the firmware of edge device and outdoor wireless bridge devices Serial Port An interface that can be used for serial communication in which only one bit is transmitted at a time A serial port is a general purpose interface that can be used for almost any type of device SSL Secure Sockets Layer A commonly used protocol d
19. set various alarm values o Alarm Duration The number of seconds an alarm remains on after DVMD has identified a target and initiated an alarm as a result The range of values is 0 300 seconds Verint Video Solutions 95 H Motion Track o Minimum Age The number of video frames that a target must be tracked before DVMD generates an alarm The higher the number the longer a target must be tracked before causing an alarm The longer a target is tracked the more certain the system is that the alarm is valid however this will program a delay or lag in the reaction time of the DVMD module The range of values is 0 300 frames The default setting of 30 requires targets to be tracked continuously for one second with NTSC cameras the default for PAL cameras is 25 Minimum Move The number of cells through which a target must move before it generates an alarm The range of values is 0 30 cells To eliminate alarms on stationary objects that have some changes such as a flashing neon sign make sure this setting is greater than 0 A setting of 0 increases the system s ability to detect slow moving or intermittent targets Target Settings This tab allows you to specify when a target will generate an alarm Module Information x Status Files Display Mask Sensitivity Target Target Size Target Elimination 14 Maximum Velocity a _ Left FT Right 0 Minimum Velocity Down a r Luma Limit
20. short the alarm input 1 and alarm ground signals on the S1100w device When receiving an alarm in a point to point configuration the relay output is configured to close the contact between the two alarm output pins up to 48V at 100 mA For example with an S1600e receiver IS1100w 1600e R i s3100 C gt z E 3 Ele Br oo Alarm Alarm Alarm Out Alarm Out Input 1 Ground Relay Relay Input 1 Ground _ pee ann 1 1 ur 7 I TI E E Q With SConfigurator you activate the alarm process by checking the Forward I O box in the Connection Creator window 36 Verint Video Solutions S1100w User Manual Performing a Hardware Reset You can perform a hardware reset on the transmitter This operation will assign the factory default settings to the S1100w listed in Appendix A on page 57 All user defined values will be lost To reset the device parameters to their factory defaults without performing a hardware operation see page 54 Following a reset you will need to reprogram the S1100w device for instance its IP address VSIP port and wireless passkey for proper operation within its network or with its wireless bridge To perform a hardware reset 1 Power down the device 2 Short the TxD and CTS wires together to locate them see page 62 3 Power up the device and wait until the normal boot up sequen
21. waves rather than wiring Verint Video Solutions 111 112 Verint Video Solutions Numerics 0 6 F1 18 2 4 GHz frequency band See frequency band 24V AC power connection warning iii 5 GHz frequency band See frequency band 802 11a See frequency band 802 11g See frequency band A abnormal power up condition 39 Access Management menu 46 account user 46 address IP See IP address adjacent channel in a DFS context 15 distance limitations 77 82 administrator account 46 Advanced menu 53 alarm cable pinout 64 configuring 34 36 motion tracking 83 allocation of frequency bands 6 antenna choosing 19 gain 19 50 installation 31 integrated 3 location for Fresnel zone 18 requirements 19 separation in colocated systems 13 77 82 APIPA service 26 65 audio cable pinout 64 configuring 34 36 Verint Video Solutions Index B band frequency See frequency band bidirectional audio 35 bit rate RF 50 serial port 44 video 11 BNC video connector 24 boot sequence 12 boot soft 55 bridge See S3100 C CAB8P mating view 64 pinout 64 usage 34 CAB9P mating view 62 pinout 63 usage 24 wiring for serial connection 32 34 62 63 cable alarm See CAB8P audio See CAB8P CAB8P See CAB8P CAB9P See CAB9P description 61 64 power 25 serial port See CAB9P camera data port configuration 2 losing a connection 37 casing of the device 4 CD Utilities xii cell wireless See wireless cell
22. 20 IP address APIPA 65 duplicate 26 setting 26 48 temporary 65 L LED status 38 limitations distance 13 77 82 Europe 11 12 15 17 line interface electrical 45 line of sight path 17 list of equipment 3 loading default configuration 54 57 location evaluation 17 login name See user name losing a connection to a camera 37 M main menu of the CLI 43 management software video xiii margin minimum RF 52 mask subnet 48 master constraint in DFS 12 defined 9 ensuring RF contact 15 See also S3100 maximum gain of an antenna 19 maximum number of devices in a cell 11 maximum transmission power See transmission power menus in the CLI 44 55 115 Index minimum RF margin 52 motion detection 83 99 N nDVR with motion tracking 83 network menu in the CLI 47 planning 5 14 O operating mode RS 422 485 45 options when ordering a device 3 order in the configuration and update process 10 output alarm or audio 34 36 P pan tilt zoom 32 parity 44 passkey for serial connection 46 for Telnet connection 46 wireless See wireless passkey ping request 48 pinout of the cables 62 64 planning RF 17 21 system 8 14 plug See connectors on the CAB9P cable point to multipoint system 13 point to point connection 28 port VSIP See VSIP port power connection performing 25 warning on 24V AC iii power requirement 4 power up conditions 39 power transmission See transmission power preventing f
23. 86 9000 Monday to Friday from 8 30 to 17 30 EST m By fax 1 450 686 0198 Warranty Each product manufactured by Verint Systems is warranted to meet all published specifications and to be free from defects in material and workmanship for a period of two 2 years from date of delivery as evidenced by the Verint Systems packing slip or other transportation receipt Products showing damage by misuse or abnormal conditions of operation or which have been modified by Buyer or repaired or altered outside Verint Systems factory without a specific authorization from Verint Systems shall be excluded from this warranty Verint Systems shall in no event be responsible for incidental or consequential damages including without limitation personal injury or property damage The warranty becomes void if the product is altered in any way Verint Systems responsibility under this warranty shall be to repair or replace at its option defective work or returned parts with transportation charges to Verint Systems factory paid by Buyer and return paid by Verint Systems If Verint Systems determines that the Product is not defective within the terms of the warranty Buyer shall pay all handling and transportation costs Verint Systems may at its option elect to correct any warranty defects by sending its supervisory or technical representative at its expense to customer s plant or location Since Verint Systems has no control over conditions of use
24. 9 plug of the cable to a COM port on your computer 5 Power the device using the red and black wires of the CAB9P cable see page 25 The status LED turns steady red and then flashes green indicating normal operation 6 Configure the S1100w parameters with the command line interface a Country of operation b Wireless passkey c IP address d Serial port parameters For the description of the procedures see Chapter 4 on page 41 7 Configure the outdoor wireless bridge for a point to multipoint application For the detailed procedure refer to the S3100 User Manual 8 Using SConfigurator ensure that the S3100 and the S1100w transmitters communicate well together o Inthe Units tab the S1100w should be hierarchically positioned under the S3100 o Inthe Link Status pane of the S3100 the S1100w should be in the Clients Slaves list o Ensure that there is end to end video transmission in the lab before installing the devices in their final location The initial configuration is now complete for the two devices Verint Video Solutions 27 3 Configuring and Installing the Device Point to Point Connection To allow video display on a monitor in a point to point context you have to create a fixed connection between the S1100w transmitter and an S1500e or S1600e receiver Typically both devices sit on the same IP subnet as SConfigurator and have the same VSIP port to access other devices refer to the device di
25. DM also known as 802 11g m 5 GHz OFDM also known as 802 11a 2 4 GHz Band The 2 4 GHz band provides 11 channels in North America and 13 in Europe In these two regions only channels 1 6 and 11 are non overlapping All these channels are for indoor or outdoor use The center frequencies of the channels are Channel Frequency GHz Channel Frequency GHz 1 2 412 8 2 447 2 2 417 9 2 452 3 2 422 10 2 457 4 2 427 11 2 462 5 2 432 12 2 467 Europe only 6 2 437 13 2 472 Europe only 7 2 442 5 GHz Band In the 5 GHz band the number of available channels and sub bands vary depending on the country of operation Most European countries adhere to the DFS Dynamic Frequency Selection and TPC Transmit Power Control regulations established by the European Telecommunications Standards Institute ETSI these regulations apply to the 5 GHz frequency band only To know which bands are available in your country of operation and whether your country adheres to DFS and TPC refer to the Wireless Frequency Plan document located on the Verint Video Solutions extranet Technical Support gt Downloads gt Tools 6 Verint Video Solutions S1100w User Manual In North America nine channels are available in the 5 GHz band all non overlapping and for indoor or outdoor use The center frequencies of these channels are Channel Frequency GHz Channel Frequency GHz 52 5 26 149 5 745 56
26. E 0 Minumum Luma v 255 Maximum Luma v Direction Elimination Up 96 Verint Video Solutions S1100w User Manual m Target Elimination Two settings relative to the target velocity o Maximum Velocity The highest velocity limit for a target to be considered valid This feature reduces nuisance alarms from high speed birds and bugs The range of values is 0 40 Minimum Velocity The lowest velocity limit for a target to be considered valid This feature reduces nuisance alarms from low speed targets such as flashing neon signs The range of values is 0 40 m Luma Limit Two settings to differentiate targets based on luma values You use luma values with thermal or infrared cameras to isolate targets above or below a certain temperature or within a temperature range o Minimum Luma The minimum setting to differentiate targets in thermal cameras using the hot black setting The range of values is 0 255 Maximum Luma The minimum setting to differentiate targets in thermal cameras using the hot white setting The range of values is 0 255 m Direction Elimination To direct the DVMD module to ignore targets moving in a specific direction Verint Video Solutions 97 H Motion Track Target Size The Target Size tab provides configurations for the size of targets that DVMD identifies Sizes are based on cells in the video image Adjusting these settings allows you to eliminate some ta
27. Europe m Point to multipoint applications with hidden masters In this context the two S3100 masters do not see each other while transmitters 2 and 3 do 3 S3100 S3100 E _ 5 ns RF Planning Successful operation of a wireless link depends on proper RF path planning and antenna installation You have to install the devices in such a way that there is a clear RF line of sight between the two antennas Location Evaluation The path between the two antennas must be free of obstacles that could disturb propagation For very short link distances less than 500 feet 152 meters you may be able to establish a working link despite partial path obstruction However radio waves will be in part absorbed and in part diffracted by the obstacles therefore affecting link reliability Because the reliability of such an installation is highly unpredictable Verint Video Solutions does not recommend it A path free of any obstacle is called an RF line of sight path To establish an RF line of sight path you must take into account the beam width of the radio signal transmitted between the two antennas This beam width is an elliptical area immediately surrounding the visual line of sight It varies in thickness depending on the length of the signal line of sight the longer the length the thicker the beam width becomes Verint Video So
28. S1100w User Manual POWERING ACTIONABLE INTELLIGENCE S1100w Firmware Release 3 60 User Manual Verint Video Solutions 2005 Verint Systems Inc All rights reserved By providing this document Verint Systems Inc is not making any representations regarding the correctness or completeness of its contents and reserves the right to alter this document at any time without notice Verint Actionable Intelligence BehaviorTrack Dellis HealthCheck Lanex Loronix Loronix Video Manager MotionTrack microDVR nDVR netDVR Nextiva Powering Actionable Intelligence SmartSight and Video Manager are trademarks of Verint Systems Inc its subsidiaries or affiliates All other registered trademarks trademarks and any associated logos are the properties of their respective owners Published by Verint Video Solutions 1800 Berlier Street Laval Quebec Canada H7L 454 www verint com videosolutions Publication date May 13 2005 Warning If you connect multiple devices on the same 24V AC power supply always wire them the same way The red power wires of all devices must be on the same power supply terminal Since the black power wire of the device is internally connected to its chassis earth swapping the power connection scheme from device to device will short out the AC power supply Warning You can install third party equipment with an earth referenced power input on the same power source as the devices
29. a A LAN can connect workstations personal computers and surveillance equipment like edge devices See also WAN MPEG 4 A graphics and video lossy compression algorithm standard that is derived from MPEG 1 MPEG 2 and H 263 MPEG 4 extends these earlier algorithms with synthesis of speech and video fractal compression computer visualization and artificial intelligence based image processing techniques Multicast Communication between a single sender and multiple receivers on a network the devices can be located across multiple subnets but not through the Internet Multicast is a set of protocols using UDP IP for transport Verint Video Solutions 107 Glossary nDVR The SmartSight video management and storage software This graphical product is used in conjunction with wired and wireless edge devices Nextiva The Verint next generation enterprise class video management and analytics platform Nextiva combines enterprise and security data with mission critical video leveraging existing investments in IT infrastructure security and business systems to enhance security and improve operational performance NTSC National Television Standards Committee The North American standard 525 line interlaced raster scanned video for the generation transmission and reception of television signals In addition to North America the NTSC standard is used in Central America a number of South American countries and some Asian countries
30. a different wireless passkey to each cell 2 Ensure that all masters see one another For more information refer to the RF Contact between Masters appendix in the S3100 User Manual 3 Position the units so that there is at least 3 feet 1 meter between each antenna 4 In each master unit set a different starting order 1 for the first unit 2 for the unit next to it 3 for the third one and so on Installing more than five cells in the 5 40 5 725 GHz band requires the use of adjacent channels This situation demands greater distances between the antennas to reduce potential radio interference Therefore you should contact the Verint Video Solutions project engineering group for assistance Verint Video Solutions 15 2 System and RF Planning Supported Setups The following colocated systems are supported in the 5 40 5 725 GHz band m Two point to multipoint applications in which the transmitters from one system do not see the transmitters from the other cell The two S3100 master units see each other m A point to multipoint repeater The two S3100 master units see each other Master Slave Repeater 16 Verint Video Solutions S1100w User Manual Unsupported Setup You cannot install the following colocated system in the 5 GHz band in
31. ace with the S1100w device The supported modes are m RS 422 4 Wires m RS 485 4 Wires m RS 485 2 Wires Verint Video Solutions 45 4 Setting Parameters with the CLI Access Management The Access Management menu takes care of user accounts user names and passwords and device security HHH DE DE DE DE DE DE DE DE DE DE DE DE DE DE DE DE DE DE DE DE DE DE DE DE DE DE DE DE Main Menu Access Management Menus 1 User Accounts 2 Security Commands p Previous Menu HH HHH HHH HHH HHH HH HH HHH HHH DE DE EEE EEE User Accounts The User Accounts menu enables you to protect the configuration of the device by restricting its access with a user name and a password Once the user account mode is activated you need the user name password combination to access the CLI through a serial connection or a Telnet session HH HHH HHH HHH HHH HH HHH DE DE DE DE DE DE DE DE DE DE EEE EEE DE DE DE DE DE DE DE DE DE DE EN Main Menu Access Management User Accounts Parameters 1 User Accounts Disabled 2 Administrator User Name USERNAME 3 Administrator Password PASSWORD Commands p Previous Menu HEHEHE HE HE HEHE HE HE HE HE HE HEH HE HE HE HE HE HE HH HE HH HH HHH HHH HHH HHH HHH KEEN Security The Security menu holds commands relative to the protection of the device Main Menu Access Management Security Parameters 1 gt IP Firmware Update Enabled 2 gt Telnet Session Enabled 3 gt KML Report Gener
32. al support for assistance m Steady red LED There is an internal error that prevents the device from starting normally Power down the device wait 30 seconds then power it up If the condition persists call Verint Video Solutions technical support m Flashing green red LED not during a firmware update The device requires a new firmware Verint Video Solutions 39 40 Verint Video Solutions Setting Parameters with the CLI The S1100w devices come with a simple command line interface CLI for configuration purposes The CLI is hierarchically organized with menus sub menus and individual options representing configuration parameters Only the parameters that you are likely to change are described Verint Video Solutions 41 4 Setting Parameters with the CLI Getting Started You can access the CLI with m A serial connection and the SConfigurator utility m A network connection and the Telnet utility see Appendix E on page 71 The SConfigurator console enables you to easily access the CLI command line interface tool to configure and customize your S1100w device To access the CLI with the SConfigurator console 1 Connect the S1100w device to a COM port of the computer using the DB 9 connector of the CAB9P cable 2 Start SConfigurator The SConfigurator window appears 3 From the General tab click Console The Verint Console window appears 4a io x a 4 gt 4 Inthe Connec
33. alling configuring and using the Nextiva S1100w wireless video transmitters Verint Video Solutions ix Preface Who Should Read this Manual This manual is intended for managers IT system administrators engineers and technicians who will use the S1100w edge devices It provides conceptual information on how to configure install and operate the devices This manual assumes that you are familiar with m Installation and manipulation of electronic equipment m General use of computers m Local area networks LANs and basic IP data communication concepts and practices m Radio frequency RF platforms m Pan tilt zoom PTZ platforms cameras and keyboards m Microsoft Windows operating systems How to Use this Manual This manual contains all the information needed to install configure and use an S1100w device Contents The S1100w User Manual is divided into the following chapters 1 Overview Provides a brief description of the features of the S1100w device and an illustration of its casing 2 System and RF Planning Lists the available frequency bands and describes planning operations relative to system setup and radio frequency RF 3 Configuring and Installing the Device Presents the configuration and installation procedures for the S1100w device x Verint Video Solutions S1100w User Manual 4 Setting Parameters with the CLI Explains how to program the S1100w device using the Nextiva comman
34. and Statistics 13 gt Quality of Service Commands i gt Identify Unit v gt Display Volatile Stream Information p gt Previous Menu MEERE Verint Video Solutions 53 4 Setting Parameters with the CLI Identifying a Device To recognize an S1100w among a large set of devices you can make its LED flash red rapidly To identify an S1100w device 1 From the main menu choose Advanced then press Enter 2 Enter i to make the LED flash red Re enter i to set the LED to its previous state 3 Enter p until you are in the main menu Enter q to exit Setting the VSIP Port The VSIP port accessible through the VSIP menu is a communication port used for protocol messaging between your computer and Nextiva devices The default VSIP port of all devices is 5510 Note VSIP ports 9541 65500 and those under 1024 are reserved and should not be used not even for serial port video or audio communication Load Default Configuration The Load Default Configuration command located in the main menu resets all device parameters to their factory settings described in Appendix A on page 57 All user defined values will be lost To reset the parameters to their factory defaults with a hardware operation instead see page 37 Following a reset you will need to reprogram the S1100w device for instance its IP address and VSIP port for proper operation within its network 54 Verint Video Solutions S1100w User Manual R
35. asynchronous PTZ serial protocol Electrical level Autolevel sensing RS 232 or RS 422 485 Alarm and Alarm input 2 dry contact inputs 1 mA max Audio Alarm output 1 relay contact output up to 48V at 100 mA Bidirectional audio Input 0 dBm into 600 ohms Output 8 dBm into 600 ohms Power Input voltage 24V AC 10 12V DC 10 optional Consumption 28 VA at 24V AC 12W 970 mA at 12V DC Physical Enclosure NEMA 4X IP 66 powder coat painted die cast aluminum with wall mounting brackets Size 9 0L x 3 9W x 3 8H inches 230L x 100W x 96H mm Weight 3 6 Ib 1 65 kg Environment 22 F to 122 F 30 C to 50 C Humidity 100 at 122 F 50 C Certification USA FCC part 15 subparts B and E Regulation Canada Industry Canada RSS 210 RSS 139 and ICES 003 102 Verint Video Solutions S1100w User Manual Europe CE marked EN 300 328 2 V1 2 1 2001 12 EN 301 893 V1 2 3 2003 08 EN 301 489 01 V1 4 1 2002 08 EN 301 489 17 V1 2 1 2002 08 EN 60950 2000 Verint Video Solutions 103 104 Verint Video Solutions Glossary This glossary is common to the Nextiva line of products Verint Video Solutions 105 Glossary Access Point A device acting as a communication switch for connecting wireless edge devices to a wired LAN Access points are mainly used with wireless transmitters to transfer wireless content onto the wired IP network APIPA Automatic Private IP Addressing A feature of Windows based ope
36. ate Time The precise date and time coming from the video processor the channel was selected m Set Clock To set the time of the DVMD module to the current time and date of the host computer 90 Verint Video Solutions S1100w User Manual Files Settings Use the Files tab to save all DVMD settings on disk or load settings from flash memory Module Information x Status Files Display Mask Sensitivity Target Target Size Load Defaults CAMERA0001 Saved Settings 7 Saved Motion Masks Lead Never saved Load HES Jul 07 12 13 43 Save Save Copy Copy OK Cancel m Load Defaults To load all the default factory settings m Saved Settings To use configurations that have been saved in memory The available options are o Load To load settings that have been previously saved o Save To save the current settings in memory o Copy This setting is unavailable since there is only one video input m Saved Motion Masks To use masks that have been saved in memory The available options are o Load To load a mask that has been previously saved o Save To save the current mask in memory o Copy This setting is unavailable since there is only one video input Verint Video Solutions 91 H Motion Track Display Settings The Display tab helps you choose what overlay text will be displayed over the video either on an analog monitor or on a computer screen It also provides confi
37. atically change its transmission power so that the total power device and antenna does not exceed the maximum value established by your country s regulations For more information about the maximum antenna gain you can use see page 19 50 Verint Video Solutions S1100w User Manual ISO Country Code You must assign the proper country of operation to the device so that it will m Comply to the DFS TPC regulations if applicable m Respect the EIRP rules m Use the proper set of frequency channels Advanced Parameters The Advanced Wireless Setup menu contains specialized RF features PRAIRIE Main Menu Wireless Communication Advanced Wireless Setup Parameters 1 gt Passkey Entry Format String 2 gt Tx Power Scale Maximum 3 Sensitivity Threshold Normal 4 Minimum Margin 15 dB 5 Indoor Outdoor RF Regulation Indoor Outdoor FCCA FCC1 Commands p gt Previous Menu Command Key Entry Format The wireless passkey can have two formats String default or Hexadecimal Tx Power Scale The transmission power scale indicates the level of emitting power of the device radio The available values are Maximum The maximum allowed 50 The power is reduced by 3 dB 25 The power is reduced by 6 dB 12 5 The power is reduced by 9 dB Minimum tThe power is set at 3 dBm By default the transmission power scale of a device subject to the TPC regulations is set to 50 Verint Video Soluti
38. ation Enabled Commands p gt Previous Menu It allows you to control m Firmware updates through the IP network m Access to Telnet 46 Verint Video Solutions S1100w User Manual IP Firmware Update You can prevent firmware updates to be performed on your device through the IP network By default this type of update is allowed For more information about firmware updates refer to the SConfigurator User Manual Telnet Session By default you can use Telnet to access the CLI of your device To improve the security of your system you may prohibit such an access In this case the CLI will only be accessible through a serial connection with the SConfigurator console Network The Network menu allows you to configure several parameters to ensure the compatibility between the S1100w and its IP network Main Menu Network Parameters 1 gt DHCP Configuration Disabled 2 Local IP Address 172 16 23 205 3 gt Subnet Mask 255 255 0 0 4 Gateway 172 16 23 205 5 gt Primary DNS Server Address 8 8 8 8 6 gt Backup DNS Server Address 8 8 8 8 7 Ping Request Target 8 8 8 8 8 gt Ping Request Send Buffer Size 32 Commands i gt Ping Remote Address p gt Previous Menu For more information about these settings contact your network administrator DHCP Configuration DHCP dynamic host configuration protocol allows devices and computers connected to a network to automatically get a valid ne
39. brated SMA torque wrench for instance from the Pasternack company available at www pasternack com Apply two or three layers of electrical tape around all RF connections The antenna cable and connectors are weather tight however vibration caused by the wind will over time loosen the connectors and reduce the efficiency of the gaskets The electrical tape will prevent this situation Carefully align the antennas of the S1100w and outdoor wireless bridge so that they have a clear RF line of sight To improve the signal level between both devices use the antenna alignment utility from SConfigurator Verint Video Solutions 31 3 Configuring and Installing the Device Performing the RS 422 485 Serial Connection The Nextiva edge devices support only the RS 232 RS 422 and RS 485 asynchronous protocols For any other protocol you may need a converter Warning At any time there must be only one serial peripheral connected to the edge device For instance when configuring the device through a COM port of the computer you must unplug any RS 422 485 peripheral RS 422 485 You use the CAB9P cable to properly connect the device to an RS 422 or RS 485 peripheral Here is the wiring scheme for the four wire RS 422 or RS 485 protocol Cable Peripheral Signal name Wire pair Wire color Signal name Rx green black green Rx Rx black Rx Tx yellow black yellow Tx Tx black Tx Signal g
40. ce is completed 4 Remove the short on the TxD and CTS pins The device is ready for use with the factory default settings Red Blue Display If a transmitter currently streaming to a video management software loses its connection to a camera the corresponding display tile will present a half red half blue black pattern Quality of Service Quality of Service QoS is a set of low level networking protocols giving higher priority to more important data flows while ensuring that the less important ones do not fail QoS is an essential technology for organizations rolling out a new generation of network applications such as real time voice communications and high quality video delivery Verint Video Solutions 37 3 Configuring and Installing the Device In the Nextiva edge devices the two available QoS flavors are Type of Service ToS and Differentiated Service Code Points DSCP For QoS to be taken into account the network infrastructure equipment switches and routers must support one of these protocols If any of these devices does not support QoS the QoS data will simply be processed as traditional non QoS data Furthermore all Nextiva edge devices on a network must support the same QoS protocol or no protocols at all You can set a priority flag to three data types coming out of an edge device video audio and control A switch or router uses this flag to determine how the current data compares to what is curren
41. d line interface The manual also includes the following appendixes A Factory Default Configuration Lists the default parameter values of the S1100w device B Cable Descriptions Describes the 8 pin and 9 pin cables supplied with the device C DHCP Support and APIPA Service Explains how the DHCP server and the Microsoft APIPA service work D DTE and DCE Connections Presents diagrams explaining how to differentiate and connect data terminal equipment DTE and data communication equipment DCE E CLI with Telnet Explains how to access the command line interface with the Telnet utility F Surge Protection Describes how to protect the S1100w device from voltage and current surges G Separation Between Devices Using Adjacent Channels Lists the minimum distances between devices using adjacent frequency channels H Motion Track Explains how to configure the optional Radiant DVMD motion track module I Technical Specifications Lists the complete technical specifications of the S1100w devices A glossary an index and compliance information complete the manual Verint Video Solutions xi Preface Conventions The following typographic conventions are used throughout this manual Visual cue Meaning Connect The name of an interface element you have to act on key to press The value of an interface element Advanced gt VSIP Any sequence of steps in the menu structure of a gra
42. eboot System The Reboot System command located in the main menu performs a soft boot on the S1100w A system reboot clears all unsaved changes in the CLI and returns to your preset configuration Verint Video Solutions 55 56 Verint Video Solutions A Factory Default Configuration Verint Video Solutions A Factory Default Configuration The S1100w is programmed at the factory with the following configuration Type Configuration Serial port Bit rate 4800 bauds Parity none Line driver auto detected RS 422 485 operating mode RS422 4 Wires Access management User name USERNAME Password PASSWORD User accounts Disabled Telnet sessions Enabled IP firmware update Enabled Global security profile Disabled SSL passkey lt empty gt Network DHCP configuration Disabled IP address 169 254 MAC address of the device Subnet mask 255 255 0 0 Gateway 169 254 MAC address of the device Communication North America Frequency band 802 11a 5 GHz OFDM Channel Auto Tx bit rate Auto Antenna gain 13 dBi Country USA Video settings m Target frame rate 30 fps North America m Target bit rate 800 kbps m Maximum quantizer 10 m Resolution CIF 352 x 240 m Video standard NTSC Video settings m Target frame rate 30 fps Europe m Target bit rate 800 kbps m Maximum quantizer 10 m Resolution CIF 352 x 240 m Video standard PAL Wi
43. ee the RS 232 connection and does not save your settings Verint Video Solutions 43 4 Setting Parameters with the CLI Serial Port The Serial Port menu enables you to establish the proper settings ensuring compatibility between the S1100w and the serial equipment with which it is connected for example dome or camera For more information about the serial port settings of this hardware product refer to its user manual or contact your manufacturer The S1100w transmitters have one configurable serial port for communicating with an external device HH HHH HHH HHH DE DEEE DEEE EE EEE Main Menu Serial Port Menus 1 RS 232 422 485 Commands p Previous Menu HHH HHH HHH HHH HHH HHH The parameters for the serial port are HHH EH HHH HEHE JE EHH HH JE JE JE EHH JE JE JE DE HEHEHE JE JE JE JE DE DE JE JE JE HEHEHE HEHE Main Menu Serial Port RS 232 422 485 Parameters 1 Bit Rate 4868 bits second 2 Parity None 3 Stop Bits One 4 Data Bits 8 5 Line Driver RS 422 6 RS 422 485 Operating Mode RS 422 4 Wires Commands p Previous Menu HHH HH HHH HHH HH HHH HH HH HHH HHH HHH HH HHH HHH EE EEE EEE EE Bit Rate The bit rate represents the data rate at which the target product operates Possible values range from 1200 bps to 230 400 bps Parity The serial equipment may have a parity of odd or even It may also not have parity check most communication devices do not use parity 44 Verint
44. eeded to configure the edge device are m An Ethernet network card m A serial port not through a USB converter m Windows 2000 Service Pack 2 or higher or Windows XP Setting Parameters Before installing a wireless system you need to set parameters relative to wireless communication IP networking and serial port You also need to establish proper communication with the corresponding S3100 outdoor wireless bridge The default IP addresses of all devices are based on the APIPA service and will be in the range 169 254 X Y where X and Yare relative to the MAC address of the individual device for more information about the APIPA service see page 65 To work properly devices on the same network must have unique IP addresses The device will not prevent you from entering a duplicate address However its status LED will turn to flashing red then the device will use an APIPA address To configure a wireless system 1 Inalab unpack the transmitter and the outdoor wireless bridge and place them on a table 2 Connect the external antenna on the S3100 and optionally on the S1100w Warning To avoid material damages you must never power any two devices while their antennas are facing one another with a distance of less than 10 feet 3 meters 26 Verint Video Solutions S1100w User Manual 3 Unpack the cable assembly CAB9P and plug its mating connector on the main connector of the S1100w transmitter 4 Connect the DB
45. eet L feet 13m 2 8m each 56 feet 17m The devices using the adjacent channels 6 and 11 in the 2 4 GHz are separated by the prescribed 56 feet 17m Verint Video Solutions 79 G Separation Between Devices Using Adjacent Channels m Using only 5 GHz channels all pointing in the same direction on two poles There is no minimum separation between any two adjacent devices sharing a pole since they do not use adjacent channels 43 feet 13m 80 Verint Video Solutions S1100w User Manual m Using only 5 GHz channels all on the same side of a tower The minimum separation between devices using adjacent channels for example 56 and 60 is the prescribed 13 feet 4m 5 8 GHz 165 5 3 GHZ on 157 5 3 GHz 64 13 feet 4m 5 8 GHz 149 5 3 GHz 60 5 8 GHZ 153 5 8 GHz 161 3 3 feet 1m each 5 3 GHz 52 NIE Verint Video Solutions 81 G Separation Between Devices Using Adjacent Channels 82 Using only 5 GHz channels on two sides of a building There is no separation limitation between any two adjacent devices since they do not use adjacent channels The minimum separation of 7 8 feet 2 4m between back to back devices is respected 5 8 GHz 5 3 GHz 5 8 GHz 5 3 GHz 5 8 GHz 165 56 157 64 149 7 8 feet 2 4m Verint Video Solutions Motion Track The S1100w device can incl
46. election regulations specified by ETSI for the selected country it is the master S3100 device that performs the tasks relative to frequency channel selection and radar detection In other words you cannot choose the frequency channel on which the edge device will run The automatic selection of the frequency channel limits the number and the configuration of the wireless cells Furthermore when colocating many cells all masters must see each other Note DFS is required only in the 5 GHz band You should start the master first then power the client when the other device is in normal operation The boot sequence of client transmitter devices is 1 Unit initialization 3 seconds 2 Roaming 2 25 seconds 3 Normal operation The device goes through the standard startup procedure cae The device roams through the channels in the available frequency bands to locate its master 3 When the master is located the client device runs normally on the selected frequency channel 12 Verint Video Solutions S1100w User Manual Colocated Cells You can operate many wireless cells in the same location provided you follow guidelines relative to frequency channel wireless passkey and distance Regarding frequency channel you cannot manually select one in the 5 40 5 725 GHz band in Europe for the detailed procedure see page 15 The wireless passkeys of colocated cells must be d
47. ently used Brush Size The size of each brush stroke in pixels Function To paint the mask Set or erase some portions of it Erase To send the current mask to DVMD and exit the Mask tab Click OK The Files tab is displayed To send the current mask to DVMD and stay in the Mask tab Click Apply To restore the mask to its previous state 94 Click Cancel Verint Video Solutions S1100w User Manual Sensitivity Settings Use the Sensitivity tab to adjust the sensitivity of the DVMD module and set several target selection attributes Module Information x Status Files Display Mask Sensitivity Target Target Size Contrast Target Selection ES A 5 8 Local E 3 Alarm Duration z z sec Filter Rates E 30 Minimum Age A x 1 30 Sec 4 Noise Level v 4 1 Minimum Move m Contrast The range of colors in each of the cells Increasing the contrast raises the dynamic threshold makes DVMD less sensitive to nuisance alarms and lowers the probability of detection Noise video sources such as light intensified cameras and infrared cameras can have high variability Video from outdoor cameras contains more variance than that from indoor scenes because of variations in lighting In noisier environments the local contrast should be as high as possible while still detecting low contrast targets m Filter Rates Default value provided by the supplier m Target Selection To
48. enu or SConfigurator Wireless pane The device will automatically take it into account and adjust its own transmission power accordingly at startup To know the maximum antenna gain you can use subtract a value from the maximum EIRP allowed in dBm Frequency band Value to subtract from EIRP 2 4 GHz in North America 11 dB 2 4 GHz in Europe 11 dB 5 GHz with DFS TPC 12 dB 5 GHz without DFS TPC 6 dB Verint Video Solutions 19 2 System and RF Planning The maximum EIRP varies depending on your country and band for more information refer to the Wireless Frequency Plan document located on the Verint Video Solutions extranet Technical Support gt Downloads gt Tools In North America for instance Frequency band Maximumtransmitted Maximum radiated power of the device power EIRP 2 4 GHZ 18 dBm 30 dBm 5 3 GHz 17 dBm 30 dBm 5 8 GHz 17 dBm 36 dBm in point to multipoint 53 dBm in point to point For example consider a device running in the 5 3 GHz band in North America Since the maximum EIRP allowed in this area is 30 dBm you should not install an antenna whose gain is greater than 24 dBi that is 30 dBm 6 dB Note Connecting an antenna with a gain higher than the calculated value contravenes your country s regulations It is your responsibility to ensure that you respect the regulations in place Interference In most countries the 2 4 GHz band is not regulated by a gover
49. es are linearly interpolated for immediate targets These values assume the camera is mounted on a pole or building looking down at an angle Then set the near target values m For the minimum limits tell the person to create the smallest profile possible Set the values in cells to create an area slightly larger than the smallest profile target that is to be detected This setting is useful to eliminate false alarms from small animals and birds m For the maximum limits tell the person to create as large of a profile as possible Set the values in cells to create an area slightly larger than the target This setting us useful to eliminate false alarms from cloud shadows on bright windy days Verint Video Solutions 99 100 Verint Video Solutions Technical Specifications Verint Video Solutions I Technical Specifications Here are the S1100w technical specifications Network RF interface SmartSight SPCF Modulation OFDM Encryption 128 bit AES Data rate 6 9 12 18 24 36 48 and max burst rate 54 Mbps Protocols Transport RTP IP UDP IP TCP IP multicast IP Others DNS and DHCP client HTTP 1 1 web server Video Compression MPEG 4 based Frame rate NTSC 1 30 fps programmable 60 fields per second PAL 1 25 fps programmable 50 fields per second Input 1 composite 1 Vpp into 75 ohms NTSC PAL Serial Port Operating mode Transparent supports any
50. eveloped by Netscape for transmitting private documents via the Internet SSL works by using a public key to encrypt data that is transferred over the SSL connection The SSL protocol secures the following data I O serial port and VSIP communication it does not apply to audio and video transmission Transceiver transmitter receiver A device that both transmits and receives analog or digital signals Transmitter A device sending video signals captured with a connected camera or dome to a receiver The transmitter converts the analog signal into a digital form before transmitting it Also called encoder VSIP Video Services over IP A proprietary communication protocol for sending messages between a computer and a Nextiva edge device or between two devices WAN wide area network A computer network that spans a relatively large geographical area Typically a WAN consists of two or more local area networks LANs 110 Verint Video Solutions S1100w User Manual WEP Wired Equivalent Privacy A security protocol for wireless local area networks WLANs defined in the 802 11b standard It is designed to afford wireless networks the same level of protection as a comparable wired network Wireless Cell A group of wireless devices that communicate together on the same radio frequency channel and share the same wireless passkey Wireless Transmission A technology in which electronic devices send information to receivers using radio
51. gurations for the type of video being played and the trajectories of objects Module Information x Status Files Display Mask Sensitivity Target Target Size Channel ID CAMOO1 Show Motion E 2 Display Position M Show Clock r Date Format Show Clock 1 100 a Pe v Show Date V Show Channel ID 1 Display Level A Jv Show Address 8 Trail Delta Interval Show Trails v Channel ID The number of the DVMD module m Show Motion The indication of whether real time video is displayed when motion is detected If activated you can see what kind of movement the DVMD module is detecting Select this setting only during the configuration process m Show Clock The indication of whether the current time will appear in overlay on the video image m Show Clock 1 100 The indication of whether the current time to 1 100 of a second will appear in overlay on the video image m Show Date The indication of whether the current date will appear in overlay on the video image m Date Format The available display formats for the date if Show Date is activated m Show Channel ID The indication of whether the channel ID will appear in overlay on the video image 92 Verint Video Solutions S1100w User Manual m Show Address The indication of whether the DVMD module address will appear in overlay on the video image m Display Position A scale allowing you to position the overlay text on
52. has a dedicated purpose m Input 1 Either transparent alarm links in a point to point configuration or with a video management software or PTL push to listen audio transmission mode m Input 2 Push to talk PTT audio transmission mode m Output Relay for the input 1 signal in point to point alarm mode You cannot program PTT PTL audio and alarms at the same time since input 1 is used in both contexts Since the S1100w transmitters are mostly used with a video management software you will perform most configuration and activation steps in it Otherwise in a point to point connection you use SConfigurator for setup 34 Verint Video Solutions S1100w User Manual Audio Two transmission modes for audio data are available provided audio is supported everywhere in your system m Full duplex Data is transferred in both directions simultaneously The I Os are available for alarms m PTT PTL The push to talk push to listen mode allows you to control audio communication between two devices When creating a point to point connection between an S1100w transmitter and an S1600e receiver in SConfigurator you set the transmission mode in the Connection Creator window The S1100w transmitters can do PTT only the PTL portion is performed on S1600e receivers in point to point configurations To activate the audio transmission channel you must trigger an activation switch for example a button that is based on the shor
53. ifferent from one another regardless of their frequency channels Distance Limitations The distance limitations between devices are m To avoid material damages you must never power any two devices while their antennas are facing one another with a distance of less than 10 feet 3 meters m If using adjacent channels see page 77 for the recommendations on the minimum distances to respect m With different frequency bands or with non adjacent channels in the same band two devices can be side by side with no minimum distance between them 5 GHz Band in North America and 2 4 GHz In the 2 4 GHz band in North America and Europe you can use the three non overlapping channels channels 1 6 and 11 to colocate wireless cells In the 5 GHz band all channels are non overlapping A typical colocation example is three wireless cells To install such a system you have to 1 In each cell assign the same wireless passkey to the S1100w devices and the S3100 bridge The wireless passkey must be different from that of the other cells Verint Video Solutions 13 2 System and RF Planning 2 Assign a different frequency channel to each S3100 device the associated S1100w devices will automatically use their master s channel For better isolation use different frequency bands in adjacent cells 3 For example in the 5 GHz band Device Cell Channel Wireless Passkey S3100_A A 52 erty
54. input with two encoders The video frame rate of the edge device can be m NTSC 1 to 7 10 15 or 30 frames per second fps m PAL 1 to 6 8 12 or 25 fps 2 Verint Video Solutions S1100w User Manual The S1100w devices can have the following video resolutions and maximum frame rates in frames per second using the NTSC PAL format Resolution Number of Number of lines Maximum frame columns rate NTSC PAL NTSC PAL NTSC PAL QCIF 176 128 144 30 25 CIF 352 240 288 30 25 2CIF 352 384 448 30 25 2CIFH 704 240 288 30 25 4CIF 704 480 576 15 12 All lines 352 480 576 30 25 2 3 D1 480 480 576 15 30 12 25 VGA 640 480 576 15 30 12 25 Without noise I Os and other factors affecting quality the device can achieve the highest frame rate For the more information about these video parameters refer to SConfigurator User Manual Shipment Your S1100w shipment contains the following items The requested transmitter which comes with an integrated patch antenna with a gain of 8 5 dBi in the 2 4 GHz band or 13 dBi in the 5 GHz band A wall mount bracket set already installed on the device A pole mount bracket set including stainless steel clamps A cable assembly for video power and serial port CAB9P The SmartSight Utilities CD containing the release notes and documentation for the device as well as the SConfigurator application The S1100w Installation Guide Verint Video Solu
55. install it To optimize your system radio performance carefully review the site planning information presented in Chapter 2 on page 5 For more information about the installation procedure of your outdoor wireless bridge refer to the S3100 User Manual Installing the Transmitter Warning When installing colocated wireless systems you have to take into account the distance limitations listed on page 13 Warning Always mount the device with the mating connectors pointing downwards Otherwise moisture may penetrate the device the associated repair costs would not be covered by the warranty To install a transmitter 1 To install the S1100w on a light pole or mast use the supplied pole mount brackets and stainless steel clamps For wall mounting use the side brackets already installed on the device Verint Video Solutions 29 3 Configuring and Installing the Device 2 If you are installing the S1100w equipment in a lightning prone environment or in a site where large AC mains power fluctuations are a common occurrence add additional external surge protection to all vulnerable connections Vulnerable connections are those that run for a long distance between the S1100w device and the connected equipment For more information about surge protection see Appendix F on page 75 If the S1100w device will be directly exposed to the sun in an environment likely to reach 122 F 50 C install a sun shield A derate of 13
56. int Console window Warning Do not use the Disconnect button to exit the CLI Clicking it does not free the RS 232 connection and does not save your settings Verint Video Solutions 73 74 Verint Video Solutions Surge Protection Voltage and current surges can be induced by lightning strikes or power line transients In the real world under the right circumstances these surges can reach sufficiently high levels to damage almost any electronic equipment Therefore you need to add protection to your devices Verint Video Solutions 75 F Surge Protection The S1100w provides basic surge protection on all electrical lines If you are installing the equipment in a lightning prone or heavy lightning environment or in a site where large AC mains power fluctuations are a common occurrence Verint Video Solutions strongly recommends that you add additional external surge protection to all vulnerable connections Vulnerable connections are those that run for a long distance between the S1100w device and the connected equipment The video camera or dome is usually within a short distance of the S1100w transmitter the S1100w interface cable can be routed directly into the camera dome housing Therefore the video line and the serial port if using a dome will seldom need additional protection The power feed usually runs down the mounting mast or wall for more than 20 feet 7 6 meters it is a good candidate for additional protection
57. ion Track Serial Port Parameters 1 Remote IP Address 6 6 6 6 2 Remote Port 5665 3 Local Port 5665 4 Initial Streaming State Enabled 5 Target USIP GUID 666606666 6666 6666 6666 666006660066 6 Connection Type UDP Commands p Previous Menu HEHE HEHE HE HEHE HE HE HEHE HE HEHE HE HE HE HEHE HE HE HE HE HE HH HE HHH HEH HH HH HH HH HHH HH HHH HHH EE EEE EEE 5 Select the Remote IP Address parameter then enter the IP address of the host computer 6 Go back to the main menu 7 Save the settings then exit the CLI Verint Video Solutions 85 H Motion Track 8 Reboot the device Establishing a Connection To test the serial port setup and prepare the configuration of the DVMD module you create a connection in the ManagerNET application You can find this application on the SmartSight Utilities CD You have to copy the ManagerNET exe file to the hard disk of the host computer To create a connection for the DVMD module 1 Power up the S1100w device 2 Start the ManagerNET application The first time you run the application the connection table is empty Z ModuleManagerNeT a ci x ipti 86 Verint Video Solutions 3 S1100w User Manual Right click anywhere in the connection table then choose Add Entry The Add Entry window appears r Module Description 1100w 1 rm Channel ID E CAMERA 1 r Network Network Type UDPLink x IP Address 17 Port
58. ipment DCE modules have the following electrical level setup Pin number Signal Measured voltage 3 Tx 0 volt 2 Rx X volts ia Ground X volts measured 0 volt measured for the Rx pin for the Tx pin Connecting DTE and DCE When connecting two modules of the same type you have to cross the data wires to create proper communication On the other hand when connecting a DTE with a DCE a straight cable is required Pe ee sees Rx_ DCE ee S DCE Tx Tx SSH aaee Rx_ ae Ix o 7 ore Tx Tx RT Bree tre ARK DTE y Ren DCE Tx Tx Verint Video Solutions 69 70 Verint Video Solutions E CLI with Telnet Verint Video Solutions E CLI with Telnet You can use the Telnet utility through SConfigurator to open the command line interface of the device Note Ensure that your computer and the S1100w device are in the same IP subnet To enter the CLI with Telnet 1 Open SConfigurator 2 Inthe Units tab discover the devices 3 Select the desired device then click Telnet The CLI main menu appears in the Verint Console window vert conse E E Connect using Tenet z Connected172 16 23 201 23 Create Text File Clear Window A HEHE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE E JE JE JE JE IE E JE JE JE JE DE E JE JE JE JE JE E JE JE JE JE JE DE E JE JE JE JE JE JE E JE JE JE JE JE E IEE Verint Video Solutions 1166w UTU 172 16 23 201 HEHEHE HEHEHE JE JE HEHE JE E JE JE JE
59. irmware update 47 protection device configuration 46 surge 30 75 protocol SPCF 2 protocols supported serial 32 PTL push to listen 35 116 PTT push to talk 35 PTZ camera connection 32 Q Quality of Service QoS 37 R radio frequency See RF radio frequency radio transmission power See transmission power reboot soft 55 receiver device 28 recognizing a device 54 red blue display 37 requirements antenna 19 computer 26 power 4 video bit rate 11 reserved VSIP ports 54 reset to factory default 37 54 57 resolution video 3 RF radio frequency channel See frequency channel contact between two masters 15 exposure considerations 21 global spectrum allocation 6 line of sight 17 menu in the CLI 49 planning 17 21 See also the wireless entries RS 232 cable pinout 63 connection 34 menu in the CLI 44 usage 24 RS 422 485 cable pinout 63 connection 32 33 menu in the CLI 44 Verint Video Solutions S S3100 communication with S1100w 27 compatibility with S1100w 9 context of use 7 See also master SConfigurator checking communication between devices 27 console 42 creating a connection 28 security settings 46 sensitivity threshold 52 separation between antennas 77 82 sequence of boot 12 serial connection 32 34 serial port cable pinout 63 cabling 32 34 connecting a single device 25 hardware setup 32 menu in the CLI 44 settings for motion track 85 serial protocols supported 32 setups in Eur
60. is displayed instead it indicates that a communication problem with the DVMD module occurred 88 Verint Video Solutions S1100w User Manual Configuring the DVMD Module You have access to the following configuration settings for the fixed camera Status Display Files Sensitivity Target Target size Clock To configure the DVMD module 1 In the Module ManagerNET window double click the desired DVMD module The Module Information window appears Select the desired tabs then enter the proper settings To save the settings use the Files tab Click OK Verint Video Solutions 89 H Motion Track Status Information The Status tab displays the current state of the DVMD module Module Information x Status Files Display Mask Sensitivity Target Target Size Address Fr Software ID JMD 4582 lt Ci S S Loader ID JSERLOAD a5 Status NO_VDEOALARM Temp TIF Date Time 070704133955 We OK Cancel m Address The address of the DVMD module It will always be FFO since the DVMD 1 product is for a single video input m Software ID The current DVMD firmware version Loader ID The current version of the serial loader firmware an internal component of the video processor m Status The current status of the video processor the video format NTSC or PAL and whether the video processor is in an alarm condition It also provides the current temperature of the DVMD device m D
61. isted pair is enclosed in square brackets 64 Verint Video Solutions DHCP Support and APIPA Service DHCP Dynamic Host Configuration Protocol allows devices and computers connected to a network to automatically get a valid IP configuration from a dedicated server The APIPA Automatic Private IP Addressing service available on the Windows operating systems enables a device to assign itself a temporary IP address Verint Video Solutions 65 C DHCP Support and APIPA Service At startup an edge device searches for a valid IP network configuration The device requires this configuration prior to starting its functions The network configuration for Nextiva devices consists of m An IP address m A subnet mask m A gateway The device first looks in its local memory If no configuration is found it tries to contact a DHCP server If DHCP configuration fails if the device does not find a server or if it cannot get a configuration from it within one minute the device assigns itself temporary network settings based on the APIPA service This service allows a device to find a unique IP address until it receives a complete network configuration either manually or from a DHCP server A device in APIPA mode does not reside on the same subnet as the other devices on the IP network therefore it may not be able to see them or be visible to them Devices use the following temporary APIPA configuration m IP address 169 254
62. lly and automate the assignment of Internet Protocol IP addresses in a network 106 Verint Video Solutions S1100w User Manual DTE data terminal equipment In an RS 232 communication channel the device to which the RS 232 interface connects Computers switches multiplexers cameras and keyboards are DTE DVR digital video recorder A device usually a computer that acts like a VCR in that it has the ability to record and play back video images The DVR takes the feed from a camera and records it into a digital format on a storage device which is most commonly the hard drive Edge Device A Nextiva device transmitting or receiving video signals through an IP network The Nextiva wireless devices are the S1000w and S1100w the wired devices are the S1500e series S1600e S1700e series S1708e series and S2500e Encoder See Transmitter Ethernet A local area network LAN architecture using a bus or star topology and supporting data transfer rates of 10 Mbps It is one of the most widely implemented LAN standards The 802 11 protocols are often referred to as wireless Ethernet Firmware Software stored in read only memory ROM or programmable ROM PROM therefore becoming a permanent part of a computing device IP Internet Protocol The network layer for the TCP IP protocol suite widely used on Ethernet networks IP Camera See S2500e LAN local area network A computer network that spans a relatively small are
63. lutions 17 2 System and RF Planning The region outlined by the signal beam width is known as the first Fresnel zone The Fresnel zone is always thicker at the mid point between the two antennas Therefore what appears to be a perfect line of sight path between the base and a remote station may not be adequate for a radio signal this is the difference between visual and RF line of sight r Visual line of sight First Fresnel zone F1 In practice it has been determined that a radio path can be considered an RF line of sight path if it has a clear opening through 60 of the first Fresnel zone or 0 6 F1 Here are values for 0 6 F1 for various signal path distances and frequency bands Distance 2 45 GHz 5 3 GHz 5 8 GHz Earth curvature mi km feet m feet m feet m effect feet m 1 16 14 4 2 9 5 2 9 8 9 2 7 0 4 6 5 27 8 4 18 7 5 7 18 5 5 2 0 6 7 11 3 37 11 25 7 6 23 6 7 2 6 1 8 15 24 53 16 36 4 11 1 35 10 6 29 8 8 For distances under seven miles the earth curvature effect is negligible However for greater distances you need to consider it in your calculations for instance for a 15 mile link in the 2 4 GHz band the two antennas must be located 82 feet higher than the highest obstacle in the RF line of sight between them that is 53 feet for the Fresnel zone plus 29 feet for the earth curvature effec
64. ly compatible for example an S1100w at version 3 20 with an S3100 at version 3 60 Verint Video Solutions 9 2 System and RF Planning In a wireless cell the order in which you configure the devices either the first time or later when they are installed in the field or update their firmware is critical if you do not want to lose access to them You should then m Update the devices starting with the farthest in terms of number of RF hops from the computer running the upgrade procedure m One step at a time get closer to the computer For example consider the following setup S1100w 1 S3100 3 S3100 2 S3100 1 You should update the devices in the following order 1 S1100w 1 You then lose contact with S1100w 1 2 S1100w 2 You then lose contact with S1100w 2 3 S3100 1 You can then reach all devices 4 S3100 2 You then lose contact will all devices except master S3100 3 5 S3100 3 You can then reach all devices For the complete firmware update procedure refer to the SConfigurator User Manual or the nDVR online help 10 Verint Video Solutions S1100w User Manual Video Bit Rate and Data Throughput You can theoretically connect up to 16 S1100w devices to a master bridge in a wireless cell In practice however video quality frame rate and system layout can limit the number of devices that a single
65. master bridge can support Video quality and frame rate influence the required data throughput Therefore you need to carefully plan the number of cameras that will work on a link The following figures were measured in typical setup situations They may vary depending on your configuration The total data throughput in a unidirectional UDP link setup is Physical bit rate Throughput for a Throughput for a 3 mile 5 km 15 5 mile 25 km distance distance 6 Mbps 3 5 Mbps 3 3 Mbps 9 Mbps 4 6 Mbps 4 3 Mbps 12 Mbps 5 5 Mbps 5 1 Mbps 18 Mbps 6 9 Mbps 6 2 Mbps 24 Mbps 7 7 Mbps 7 Mbps 36 Mbps 8 9 Mbps 8 Mbps 48 Mbps 9 7 Mbps 8 6 Mbps 54 Mbps 10 Mbps 8 8 Mbps For the bit rate requirements of the edge devices to which the cameras are connected consult the Bit Rate Settings for Video Servers document located on the Verint Video Solutions extranet Technical Support gt Downloads gt Tools TPC If the country of operation of the S1100w device requires conformity to the TPC Transmit Power Control regulations the transmission power of its radio is automatically reduced by 3 dB before leaving the Verint Video Solutions factory However in case of a weak wireless link that is a link with an RF margin of less than 15 dB you have the opportunity to use the maximum transmission power see page 51 Verint Video Solutions 11 2 System and RF Planning DFS To follow the DFS Dynamic Frequency S
66. meras to an IP network Note The S1100w edge devices require professional installation Verint Video Solutions 1 1 Overview About the S1100w The S1100w devices come as transmitters only You can buy 12V DC or 24V AC devices The S1100w covers the 2 4 GHz and 5 GHz frequency bands in North America and Europe You can purchase an S1100w device with a motion track device S1100w MT It provides the most accurate cost effective wireless outdoor motion tracking capability available today It incorporates adaptive digital processing technology to achieve highly sensitive detection in a wide range of operating environments with very low false alarm rates For more information see Appendix H on page 83 Unless otherwise specified the word S1100w refers to any of these devices Each device is configured to operate right out of the box with the most popular camera data port configuration 4800 baud 8 data bits no parity 1 stop bit Security Every S1100w device comes with the SPCF SmartSight Point Coordination Function security feature SPCF is a proprietary MAC Media Access Control protocol using AES encryption with key rotation over the wireless link to secure communication between the devices and resolve hidden node quality of service range and problems inherent to 802 11 wireless networking products SPCF secures VSIP communication as well as the audio and video data Video The S1100w has one video
67. mity Manufacturer Verint Systems Inc 1800 Berlier Laval Qu bec H7L 4S4 Canada Declares under sole responsibility that the product Product name Wireless video transmitter Model number S1100w CE 5x S1100w CE 24 To which this declaration relates is in conformity with the following standards or other documents R amp TTE Directive 1999 5 EC EN 300 328 2 V1 2 1 2001 12 EN 301 893 V1 2 3 2003 08 EN 301 489 01 V1 4 1 2002 08 EN 301 489 17 V1 2 1 2002 08 EN 60950 2000 I the undersigned hereby declare that the equipment specified above conforms to the above Directive s and Standard s May 6th 2004 Laval Canada PE Willie Kouncar Vice President Product development Verint Video Solutions 122 Verint Video Solutions S1100w User Manual Turkey Declaration of Conformity Manufacturer Verint Systems Inc 1800 Berlier Laval Qu bec H7L 4S4 Canada Declares under sole responsibility that the product Product name Wireless video transmitter Model number S1100w TR 12VDC 24 S1100w TR 24VAC 24 S1100w TR MT 12VDC 24 S1100w TR MT 24VAC 24 To which this declaration relates is in conformity with the following standards or other documents R amp TTE Directive 1999 5 EC EN 300 328 2 V1 2 1 2001 12 EN 301 489 01 V1 4 1 2002 08 EN 301 489 17 V1 2 1 2002 08 EN 60950 2000 I the undersigned hereby declare that the equipment specified above conform
68. n mainly for communication and serial connection m Physical installation in its final location m Alarm and audio configuration Verint Video Solutions 23 3 Configuring and Installing the Device Cable for Power Video and Serial Data The supplied CAB9P cable assembly is used for video power and serial port connection Mating connector DB 9 connector Terminal block Power wires BNC video connector For the detailed pinout see page 62 Serial Port The S1100w integrates one multipurpose serial port This port is used for system configuration and data communication pan tilt zoom PTZ access control or other By default the port automatically detects if it is connected to an RS 232 or RS 422 485 serial device The CAB9P cable is supplied with a female DB 9 plug enabling RS 232 connections However most PTZ cameras keyboards and similar devices use RS 422 485 connections Therefore you will have to adapt the CAB9P cable for its different uses m During the configuration process of the S1100w you need to access a computer so the DB 9 connector is required for RS 232 communication 24 Verint Video Solutions S1100w User Manual m Later when installing the device in its final location you will likely want to connect it to RS 422 485 equipment therefore requiring changes on the cable You should keep the DB 9 connector on the cable for later use Warning At any time there must be only one serial de
69. netic field is created that is able to propagate through space Many wireless technologies are based on RF field propagation RS 232 A standard interface approved by the Electronic Industries Alliance EIA for connecting serial devices RS 422 A standard interface approved by the Electronic Industries Alliance EIA for connecting serial devices designed to replace the older RS 232 standard because it supports higher data rates and greater immunity to electrical interference RS 485 An Electronics Industry Alliance EIA standard for multipoint communications S1000 Series The series of secure outdoor wireless video systems one receiver and one transmitter per system The series covers the 2 4 GHz band in North America and Europe and the 5 GHz band in North America Starting with firmware release 3 20 the S1000 series is replaced by the S1100 edge devices S1000w The outdoor wireless video transmitter operating on the 2 4 GHz frequency band S1100 The newest series of secure outdoor wireless video systems one receiver and one transmitter per system covering the 2 4 and 5 GHz bands in North America and Europe S1100w The multiband 2 4 and 5 GHz outdoor wireless video transmitter operating in North America and Europe S1500e Series The series of wired edge devices receivers and transmitters designed for video monitoring and surveillance over IP networks The transmitters in the series offer from one to eight video inputs the
70. nmbvcxzapoiu S1100w_A1 A 52 ertynmbvcxzapoiu S1100w_A2 A 52 ertynmbvcxzapoiu S1100w_A3 A 52 ertynmbvcxzapoiu S3100_B B 149 PUK98rewq4123qzx S1100w_B1 B 149 PUK98rewq4123qzx S1100w_B2 B 149 PUK98rewq4123qzx S1100w_B3 B 149 PUK98rewq4123qzx S3100_C C 64 987123jkl456wert S1100w_C1 C 64 987123jkl456wert S1100w_C2 C 64 987123jkl456wert S1100w_C3 C 64 987123jkl456wert In each cell install the S1100w devices such that each one has a clear RF line of sight with its associated S3100 bridge This application can be illustrated this way where the three cells are in the same location 14 Verint Video Solutions S1100w User Manual 5 GHz Band in Europe The maximum number of colocated cells corresponds to the number of channels in the available frequency bands that can be used outdoors For instance in most countries of Western Europe you can have up to 11 colocated cells in the 5 40 5 725 GHz band However because the master units must see each other in a DFS context the variety of supported setups is limited In this context you can easily install up to five cells By respecting the following steps you can assume that the cells will not share the same frequency channel making the complete bandwidth available for each one You have to 1 Assign
71. nment agency this absence of frequency coordination can result in interference between various systems For instance if a link with an RF line of sight is subject to excessive video delay and very low frame rate or possibly breakdown of video images it could be due to interference Fortunately you have ways of adapting your setup to avoid interference m RF channel selection In the 2 4 GHz band the S1100w has 11 or 13 channels to choose from In case of interference it is recommended to change channel until you find a clean one m Antenna selection Replacement of the integrated antenna by a higher gain one can significantly lower the interference from other radio systems Replace the antenna if switching channels does not correct the problem or if all channels must be used to colocate several systems 20 Verint Video Solutions S1100w User Manual The 5 GHz band is less cluttered than the 2 4 GHz band resulting in less potential interference from other wireless systems RF Exposure Considerations In order to comply with the RF exposure requirements of CFR 47 part 15 in North America the devices must be installed in such a way as to allow a minimum separation distance of 12 inches 30 cm between antennas and persons nearby Verint Video Solutions 21 22 Verint Video Solutions Configuring and Installing the Device The steps required to prepare your S1100w device for operation are m Basic configuratio
72. nnnnn nenn nennen 31 Performing the RS 422 485 Serial Connection 32 Configuring the 1 OS ceceeeeeee esse ee ee eee eens nenn nn nn en 34 AUCIO za a een deli 35 Alarm S ressens read onen ak HERE 36 Performing a Hardware Reset nsssrerennnnnennnnnnen nenn 37 Red Blue Display 4 0 0 Hanna ana isana ian 37 Quality of Service ui ssssiassen adui sn nnd nn ai 37 Status LEDs ae an en ar een an ne cage A 38 Chapter 4 s Setting Parameters with the CLI 41 Getting Started 4 234 cause san anne Hanna eines 42 Serial Port unseren aA a TEANA 44 Access Management 444 46 User Accounts arsti sridi iiag ntara iratnak iadaa TAa 46 SECUrITY era dame a a Er a ana aap E ne Fate DEEE 46 NetWork can a en EA tin AEA ae 47 Wireless Communication 22 49 Basic Parameters 8 49 Advanced Parameters 2 51 System StACUS ii ss een verrine see rene N 53 Advanced issie 22 ee al a css tags 53 Identifying a Device eserasansneenennnnnnn nennen nn nn nn en 54 Setting the VSIP Port ccccccececscsceseeretencsecnecesvesecaes 54 Load Default Configuration zuunssererennnnnen nennen nennen 54 Reboot SYSTEM css su ipina enocotneges sense diaid pad energie sas 55 Appendix A Factory Default Configuration 57 Appendix B Cable Descriptions mmmmmnns 61 CABOP ae maine aba tetecnaawaanes E ieee ee Meg dd Dee 62 CABSP uns remettant reset inate 64 Appendix C DHCP Support and APIPA Service
73. no warranty is made or implied as to suitability for customer s intended use There are no warranties expressed or implied except as stated herein This limitation on warranties shall not be modified by verbal representations xiv Verint Video Solutions S1100w User Manual Equipment shipped ex works Verint Systems factory shall become the property of Buyer upon transfer to the common carrier Buyer shall communicate directly with the carrier by immediately requesting carrier s inspection upon evidence of damage in shipment Buyer must obtain a return materials authorization RMA number and shipping instructions from Verint Systems prior to returning any product under warranty Do not return any Verint Systems product to the factory until RMA and shipping instructions are received Verint Video Solutions XV xvi Verint Video Solutions Overview The S1100w is the industry s first wireless video transmitter allowing digital video transmission over multiple license free bands It delivers high quality MPEG 4 based video at 30 frames per second in NTSC 25 in PAL over local and wide area networks LANs and WANs This wireless edge device is built on open standards to provide long term investment protection Combined with an S3100 outdoor wireless bridge the S1100w enables analog CCTV extension over the enterprise s network at a cost lower than that of laying new cables The S1100w also allows the migration of analog CCTV ca
74. ntry of operation in each of the three operation modes refer to the Wireless Frequency Plan document located on the Verint Video Solutions extranet Technical Support gt Downloads gt Tools The default factory value for most countries is indoor outdoor 52 Verint Video Solutions S1100w User Manual System Status The system status information indicates the current values of internal S1100w parameters including the firmware version Main Menu System Status Menus 1 gt Storage Parameters ISO Country Code UNITED_STATES 84 gt Firmware Version 3 68 build 225 Loader Version 8 24 build 1 Build Date Apr 29 2005 at 11 61 27 CPU Info Rev 1 8 CPU Frequency 199865688 Uptime 1 days 82 48 21 Serial Number 688b6b 33127e CPLD Version 6 Internal Value 1 26666686 16 Audio Hardware Present Production Date 83 85 Module Radiant Absent Board Temperature 43 Commands p gt Previous Menu Advanced The Advanced menu holds a series of advanced setups mainly used by Verint Video Solutions technical support Some of these parameters are available through SConfigurator or a video management software Main Menu Advanced 1 gt Video 2 gt Video Status 3 gt System Time 4 System Time Stats 5 gt Serial Port lt IP gt 6 gt USIP 7 gt USIP Statistics 8 gt Audio 9 gt License Management 10 gt Serial Port Status 11 gt Test and Debug 12 gt Communication Status
75. off and on the user is encouraged to try to correct the interference by one or more of the following measures m Reorient or relocate the receiving antenna m Increase the separation between the equipment and the S1100w device m Connect the equipment into an outlet on a circuit different from that to which the receiver is connected m Consult the dealer or an experienced radio TV technician for help Any changes or modifications not expressly approved by Verint Video Solutions could void the user s authority to operate the equipment 120 Verint Video Solutions S1100w User Manual Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power EIRP is not more than that required for successful communication Italia L uso di questo apparato in Italia regolamentato da m D Lgs 1 8 2003 n 259 articoli 104 attivit soggette ad autorizzazione generale e 105 libero uso per uso privato m D M 28 5 03 per la fornitura al pubblico dell accesso alle reti e ai servizi di telecomunicazioni R LAN or R LAN and Hiperlan Verint Video Solutions 121 Compliance Europe Declaration of Confor
76. ons 51 4 Setting Parameters with the CLI Sensitivity Threshold The sensitivity threshold is the minimum signal level perceived by the radio of the device Reducing the sensitivity of the radio enables unwanted noise to be filtered out A safe value is 10 dB below the current received signal level displayed in the Advanced gt Communication Status and Statistics gt Wireless Status menu The default value Normal represents the most sensitive context You must be careful not to reduce the sensitivity to a level where the device would not hear its legitimate correspondent Minimum Margin The minimum margin is used when the transmission bit rate is set to Auto see page 50 It represents the difference in dB between the actual signal received by the device and the minimum signal required by a given bit rate to correctly receive data on the RF link The default minimum margin is 15 dB Indoor Outdoor RF Regulation Depending on the country of operation and the chosen frequency band the device is allowed to operate indoors only outdoors only or either indoors or outdoors The frequency channels available in the indoor only regulation are different from those assigned to indoors outdoors the same goes for the outdoor only channels Note Under the RF regulation a device programmed to be used only indoors must not be installed outdoors and vice versa To know which frequency channels are available in your cou
77. ope 16 17 shipment list 3 SmartSight Utilities CD xii soft reboot 55 software reset 54 software video management xiii SPCF 2 specifications technical 101 103 spectrum allocation 6 status LED 38 status system 53 subnet mask 48 support technical xiii surge protection 30 75 system reboot 55 system status 53 T target device connecting 32 34 technical specifications 101 103 technical support xiii Verint Video Solutions S1100w User Manual Telnet accessing the CLI 71 preventing access 47 temporary IP address 65 terminal block on the CAB9P cable 24 62 threshold sensitivity 52 throughput data 11 timeout CLI 43 ToS Type of Service 37 TPC Transmit Power Control 6 11 track motion 83 99 transmission power when choosing an antenna 19 in the CLI 51 reducing for TPC 11 U update of firmware preventing 47 without losing devices 10 user account 46 user name 46 Utilities CD xii V Verint Video Solutions web site xiii version of firmware compatibility 9 displayed 53 video connector 24 video management software xiii video settings 2 VSIP port 54 W warranty xiv web site Verint Video Solutions xiii wireless cell 8 14 wireless communication parameters 49 52 wireless frequency plan 6 117 Index wireless passkey in the CLI 49 in colocated cells 13 wiring scheme alarm 64 audio 64 RS 232 62 63 RS 422 485 32 33 118 Verint Video Solutions Verint Video Solutions Compliance
78. phical application in the navigation structure of a web site and so on connection_name Text that must be replaced by a user supplied value Text representing variable content S1100w zxh The name of a command file or directory Text that appears on the screen Examples of user supplied values Related Documentation In addition to this manual the following documentation is also available m S1100w Installation Guide Contains the configuration steps and the installation procedure for the S1100w edge device m SConfigurator User Manual Presents the instructions on how to use a proprietary Verint Video Solutions software to configure the edge device connect it to other devices and update its firmware m Release Notes Contain information about S1100w upgrades and known issues still under investigation as well as a description of features not covered in this version of the documentation All these documents are contained on the SmartSight Utilities CD shipped with the device Furthermore a paper copy of the installation guide is included with your order xii Verint Video Solutions S1100w User Manual Related Nextiva Products You use the S1100w devices with the S3100 outdoor wireless bridge You may also use them with the nDVR and Nextiva video management and storage software packages For more details about any of these products visit our web site For pricing information call your dealer About U
79. rating systems that enables a device to automatically assign itself an IP address when there is no Dynamic Host Configuration Protocol DHCP server available to perform that function Also known as AutolIP Bridge A device linking a wireless network to a wired Ethernet network The newest Nextiva bridge is the S3100 Camera See S2500e CCTV closed circuit television A television system in which signals are not publicly distributed cameras are connected to television monitors in a limited area such as a store an office building or on a college campus CCTV is commonly used in surveillance systems CIF common image format A video format that easily supports both NTSC and PAL signals Many CIF flavors are available including CIF QCIF 2CIF and 4CIF Each flavor corresponds to a specific number of lines and columns per video frame CLI command line interface A textual user interface in which the user responds to a prompt by typing a command Codec coder decoder A device that encodes or decodes a signal Configuration Assistant A proprietary graphical program used to configure and update the firmware of the S1100 edge devices DCE data communication equipment In an RS 232 communication channel a device that connects to the RS 232 interface Nextiva edge devices and modems are DCE Decoder See Receiver DHCP Dynamic Host Configuration Protocol A communication protocol that lets network administrators manage centra
80. reless m Wireless passkey ABCDEFGHIJKLMNOP Tx power scale Maximum 58 Verint Video Solutions S1100w User Manual Type Configuration Wireless m Wireless passkey ABCDEFGHIJKLMNOP Communication m Frequency band 802 11a 5 GHz OFDM Europe m Channel Auto m Tx bit rate Auto m Antenna gain 13 dBi m Country United Kingdom m Tx power scale 50 3 dB VSIP m VSIP Port 5510 m VSIP Multicast IP Address 224 16 32 1 m VSIP Discovery IP Address 255 255 255 255 Verint Video Solutions 59 60 Verint Video Solutions Cable Descriptions The wireless devices use the following two cables m CAB9P Power video and serial data communication m CAB8P Audio and alarms Note To determine the Rx and Tx pins of your equipment see Appendix D on page 67 Verint Video Solutions 61 B Cable Descriptions CAB9P The CAB9P cable supplied with the wireless devices is used for power video and serial communication that is PTZ data with the RS 422 485 protocol or RS 232 communication with the DB 9 connector The mating side view of the cable is using the RS 232 signal terminology 62 Verint Video Solutions S1100w User Manual Here is the pinout of the CAB9P cable Power 1 VIN RETURN Black Red 2 LVIN Red Black N C 1 3LCTS Rx Green Black a fo Q 2 0486 N C 4 LRTS Tx
81. rgets so that they do not generate alarms The target size is calculated based on 8x8 cells These settings are important to the overall performance of the DVMD module Module Information x Status Files Display Mask Sensitivity Target Target Size r Far Target Width Limits ES A Art E 72 Maximum E 1 Minimum vw w r Far Target Height Limits A A 72 Maximum 1 Minimum v w r Near Target Width Limits Ar Maximum 1 Minimum ka vr r Near Target Height Limits A 72 Maximum 1 Minimum I u For the Far Target Width Limits and Far Target Height Limits settings ask a person to stand in the far top field of view of the camera Then set the far target values m For the minimum limits tell the person to create the smallest profile possible Set the values in cells to create an area slightly larger than the smallest profile target that is to be detected This setting is useful to eliminate false alarms from small animals and birds m For the maximum limits tell the person to create as large of a profile as possible Set the values in cells to create an area slightly larger than the target This setting us useful to eliminate false alarms from cloud shadows on bright windy days 98 Verint Video Solutions S1100w User Manual For the Near Target Width Limits and Near Target Height Limits settings ask a person to stand in the near bottom field of view of the camera The target siz
82. round brown black brown Signal ground Signal ground black Signal ground 32 Verint Video Solutions S1100w User Manual For example here is an S1100w transmitter connected to a dome PTZ in an RS 422 2 wire context BNC barrel connector Status Coax cable Power red and black Rx Rx green and black Rx Rx Tx Tx yellow and black Signal ground brown and black Signal ground Target device dome For a two wire half duplex RS 485 connection 1 Use the following wiring scheme Cable Peripheral Signal name Wire pair Wire color Signal name Data green black green Data Data black Data Signal ground brown black brown Signal ground Signal ground black Signal ground 2 Set the line driver to the 485h f value see page 45 Verint Video Solutions 33 3 Configuring and Installing the Device RS 232 For an RS 232 connection use the following wiring scheme to plug the device to the peripheral using the DB 9 connector on the CAB9P cable DB 9 pin number Cable signal name RxD TxD Signal ground RTS CTS l NIA WIN The numbering of the pins on the DB 9 connector is Configuring the I Os To program alarms or events or use the audio features of the S1100w device you need the CAB8P cable assembly For detailed pinout information see page 64 The S1100w supports two inputs and one output Each signal
83. s Verint Systems NASDAQ VRNT is a leading global provider of video security surveillance and business intelligence solutions Verint Video Solutions transform digital video into actionable intelligence timely mission critical insights for faster more effective decisions Today more than 1000 companies in 50 countries use Verint Systems solutions to enhance security boost operational efficiency and fuel profitability Web Site For information about the Nextiva line of products visit www verint com videosolutions To download application notes and user documentation as well as request the latest versions of firmware and software you need access to the Verint Video Solutions partner extranet To register go to www verint com smartsight support The data sheets of the Nextiva edge devices are also available directly at www verint com smartsight support Support If you encounter any type of problem after reading this manual contact your local distributor or Verint Video Solutions representative You can also use the following sections on the Verint Video Solutions partner extranet to find the answers to your questions m SmartSight FAQ m SmartSight Requests m SmartSight My Account Verint Video Solutions xiii Preface Verint Video Solutions technical support personnel is available to help you use your Nextiva edge devices and the related software m By phone 1 888 494 7337 North America or 1 450 6
84. s and masked areas are saved in the onboard flash memory Physical Connections To configure the DVMD module the S1100w MT device and the computer running the ManagerNET application must be on the same IP network Therefore you must be able to ping the device from the ManagerNET host computer The DVMD module is integrated in the enclosure of the S1100w MT device Embedded DVMD module Host computer jojo 84 Verint Video Solutions S1100w User Manual Configuring the Dedicated Serial Port To configure the DVMD module with the ManagerNET application you must enable the IP communication with a dedicated S1100w MT serial port To configure the serial port of the device 1 Start SConfigurator on the host computer 2 Goin the Units tab then click Discover 3 Select the S1100w then click Telnet The main menu of the CLI for the transmitter appears HHH HH HH HH HHH HHH HHH EE EEE EEE EEE EE Main Menu Menus 1 Serial Port 2 Access Management 3 Network 4 Wireless Communication 5 System Status 6 Advanced Commands s Save Settings r Reboot System 1 Load Default Configuration q Quit 4 Select Advanced gt Serial Port IP gt Motion Track Serial Port HHH HHH HH HHH HHH HEHEHE JE HHH JE JE JE JE JE JE JE JE JE JE JE DE HEH JE JE JE JE HEHEHE JE JE JE JE JE JE JE JE JE JE JE ME FEFE Advanced Serial Port IP Mot
85. s to the above Directive s and Standard s December 14th 2004 Laval Canada LA ME A Willie Kouncar Vice President Product development Verint Video Solutions Verint Video Solutions 123 124 Verint Video Solutions Verint Video Solutions 1800 Berlier Street Laval Quebec Canada H7L 4S4 VERINT POWERING ACTIONABLE INTELLIGENCE
86. scovery section in the SConfigurator User Manual Note The receiver must be running firmware version 3 10 or higher For more information about the connection procedure refer to the Managing Connections chapter in the SConfigurator User Manual To perform a point to point connection 1 Start SConfigurator 2 Inthe Units tab discover the desired devices The discovered devices appear in the Units box 3 Select the Connections tab then click Add The Connection Creator window appears Transmitters Receivers 172 16 0 40 Stream2 172 16 0 45 Stream1 172 16 0 45 Stream2 Video T Enable Audio UDP z prie gt M Forward 1 0 IV Forward Serial Port Data 4 Select a transmitter in the left column and a receiver in the right one In the Transmitters column you have access to the two encoders of each input the video stream is the same for both 28 Verint Video Solutions S1100w User Manual 5 To disable I O data transmission for example alarms between the two selected devices clear Forward I O 6 To disable serial port data transmission like PTZ commands clear Forward Serial Port Data 7 To enable audio between the devices ensure that Enable Audio is checked then select the audio mode 8 Click Connect You should now have video on the monitor connected to the receiver Installing the Wireless System After configuring successfully your wireless system you are ready to
87. sight between each S1100w device and the outdoor wireless bridge in each cell However the S1100w devices can be completely hidden from one another 8 Verint Video Solutions S1100w User Manual Point to Multipoint Application A point to multipoint application is a wireless cell made up of an S3100 bridge the master and several S1100w transmitters the clients Here is a typical point to multipoint system S1100w S3100 h a For example to associate three S1100w devices to one outdoor wireless bridge you have to 1 Assign the same wireless passkey to the S1100w devices and the S3100 bridge The wireless passkey must be different from that of other colocated cells if any 2 In a non DFS context assign a frequency channel to the S3100 device In a DFS context the master device will automatically select a channel The associated S1100w devices will automatically use their master s channel 3 Install the S1100w devices such that each one has a clear RF line of sight with the S3100 bridge For the configuration and installation procedure see page 25 Compatibility Issues When planning your wireless systems you have to take into account the firmware versions of the involved devices It is recommended that the S1100w transmitters have the same firmware versions as their associated master however from version 2 60 and up the devices are ful
88. t For help consult the Verint Video Solutions project engineering group 18 Verint Video Solutions S1100w User Manual A common problem encountered in the field and related to the 0 6 Fi clearance rule is building obstruction The proposed visual path may just barely clear a building but the RF line of sight will not In such a case the signal will be partially absorbed and diffracted Increasing the height of the two antennas or the gain of the antennas are the only alternatives to improve the link quality Note At 2 4 and 5 GHz radio waves are highly attenuated by dense foliage A link established in the fall or winter season may be adversely affected in the spring and summertime if it is established below tree level Antenna Requirements Verint Video Solutions offers many antennas to meet various distance requirements You have to consider many factors when choosing an antenna including the distance to cover the RF bit rate the radiated power EIRP and the frequency band used For systems located in North America on the 5 GHz band you can use the Wireless Distance Calculator located on the Verint Video Solutions extranet Technical Support gt Downloads gt Tools The combined transmission power of the device and antenna must not exceed the maximum value established by your country s regulations To ensure that this maximum is not exceeded enter the gain of the chosen antenna in the CLI Wireless Communication m
89. t using list select the COM port used to communicate with the device 42 Verint Video Solutions S1100w User Manual 5 Click Connect The CLI main menu appears HHH HH HHH HH HHH HHH EE DE DE EEE EEE EE EEE Main Menu Menus 1 Serial Port 2 Access Management 3 Network 4 Wireless Communication 5 System Status 6 Advanced Commands s Save Settings r Reboot System 1 Load Default Configuration q Quit HHH HH HHH HHH DE JE DE HHH HHH DE DE DE DE HIE The CLI has a timeout that is triggered after three minutes of inactivity When the timeout occurs O You lose access to the command line o The Thank you for using the Verint Video Solutions CLI message appears at the command line o The Verint Console window becomes disabled o The Disconnect button switches to Connect To reactivate the CLI after a timeout click Connect 7 To work through the CLI menu structure follow these guidelines O To execute a command or open a menu type in the corresponding letter or number then press Enter o To return to the previous menu enter p 8 To end the CLI work session a Save the settings by entering s at the main menu then pressing Enter b Exit the CLI by entering q at the main menu then pressing Enter Depending on the changed settings the device may perform a soft boot c Close the Verint Console window Warning Do not use the Disconnect button to exit the CLI Clicking it does not fr
90. te Address command 48 Verint Video Solutions S1100w User Manual Wireless Communication The Wireless Communication menu contains a set of parameters relative to radio frequency RF RKRRRRRERRRERERRRERRRRERRRERERRRRFRRRFRRRFRRRRRRRRRR Main Menu Wireless Communication Menus 1 Advanced Wireless Setup Parameters 2 Passkey 122662626266 3 MAC Mode SPCF 4 MAC Role Client 5 RF Band 862 11g 2 4 GHz OFDM 6 Channel Auto 7 Tx Bit Rate Auto 8 Antenna Gain 6 dBi 9 ISO Country Code UNITED _STATES 846 Commands p Previous Menu HHH HH HHH HE HHH HHH HE HH HH HH HHH HH HHH HHH HHH HEHE Basic Parameters Passkey The wireless passkey is a unique case sensitive identifier enabling secure and encrypted RF communication between the S1100w device and its outdoor wireless bridge The passkey length varies depending on the key entry format presented on page 51 m 32 digits if hexadecimal m 16 characters if string default For the wireless connection to be secure do no enter a known name like a street name but instead use a mix of digits and letters Furthermore do not disclose the passkey The connection security is based on the secrecy and uniqueness of the passkey It is a good practice to change the default passkey during the configuration process Verint Video Solutions 49 4 Setting Parameters with the CLI RF Band The following frequency bands are available m 802 11a 5
91. the video image Select the number of cells 8X8 from the top of the video image to place the overlay A higher number lowers the position of the overlay text a lower number moves the text higher m Display Level A scale setting the black and white contrast of the overlay text The smallest value indicates that the text is black and the highest that the text is white m Show Trails Default value provided by the supplier m Trail Delta Interval Default value provided by the supplier Mask The Mask tab allows you to define masks that is areas that the DVMD module will ignore in the camera s field of view therefore preventing false alarms from occurring DVMD uses the mask that is currently loaded Note When the Mask tab is opened the DVMD module cannot detect targets x Module Information Status Files Display Mask Sensitivity Target Target Size Motion Mask Erase All Set All UnDO GRAB Jv Use Motion Mask r Brush Size Function 1x1 Set C 3x3 C a Erase Verint Video Solutions 93 H Motion Track Erase All To clear the displayed mask The original grabbed image is restored Set All To mask the entire video image UnDO To cancel the most recent mask edits GRAB To mask an area This command uploads an image low resolution not real time from the video input in the Motion Mask area Use Motion Mask The indication of whether a motion mask is curr
92. ting of the alarm input 2 and alarm ground signals If both the transmitter s and receiver s PTT switches are activated at the same time the receiver will have precedence Audio will be transferred from the S1600e receiver to the S1100w transmitter Here is a typical PTT PTL application in a point to point context S1100w P EE Said 1600e R b oo In 2 and Gnd Audio Out Audio In In 2 and Gnd Gnd and In 1 Audio Out Audio In signals signal signal terminals terminals connector connector 7 4 T 4 The S1100w device supports the line in input type With SConfigurator ensure that the input type in the Audio tab reflects this value Regardless of the transmission mode the connections for the audio equipment are m You plug the audio input signal of the device to the Line out connector on a pre amplifier Then you plug a microphone on the pre amplifier Verint Video Solutions 35 3 Configuring and Installing the Device m You plug the audio output signal of the device to the Line in connector on an amplifier Then you plug a speaker on the amplifier The audio input output specifications are Mode Gain Impedance Frequency range Input 0 dBm 600 ohms Output 8 dBm 600 ohms 300 3600 Hz Alarms The S1100w device can generate and receive alarms To generate an alarm you have to
93. tions 3 1 Overview The shipment may also contain the following options m A high gain antenna Warning When choosing an antenna you must ensure that the combined transmission power of the device and antenna does not exceed the maximum value established by your country s regulations For more information see page 19 m A junction box JBOX m An alarm audio cable assembly CAB8P m A power supply Note If you are using a power supply other than those supplied by Verint Video Solutions you need to ensure that they have a minimum capacity of 1A for 12V DC or 30 VA for 24V AC Casing Description The S1100w electronics are enclosed in a weather tight cast aluminum module All cable entries are mounted on the underside of the module to maintain its weatherproof properties The front panel integrates one bicolor visual indicator that illustrates the operational state of the device Antenna port Integrated antenna Status indicator Status Auxiliary connector alarm audio Main connector video power serial port 4 Verint Video Solutions System and RF Planning To allow optimal configuration you must properly plan your network especially RF radio frequency and configuration layout Verint Video Solutions 5 2 System and RF Planning Frequency Bands and Channels The S1100w supports communications in the following frequency bands in North America and Europe m 2 4 GHz OF
94. tly going through it To set the QoS values you need to go in the command line interface CLI of the device then access the Advanced gt Quality of Service menu For the procedure see page 41 Status LED The status LED is a bicolor green red LED that provides detailed information on the current state of the device Condition Indication Steady red The device is powering up Flashing red 1 sec The IP address of the device is already intervals assigned to another device in the network Flashing green 3 sec The firmware has started but RF intervals communication is not established Flashing green 1 sec The firmware has started RF communication intervals is established but no video serial data is transmitted Flashing green The firmware has started RF communication 0 2 sec intervals is established and video serial data is transmitted Three consecutive red No video source is detected and no video is blinks every 2 sec transmitted Flashing green red The device is undergoing a firmware update 1 sec intervals Flashing red 0 1 sec The device is being identified intervals 38 Verint Video Solutions S1100w User Manual At least one of them must be transferred to get the LED condition The following power up conditions are abnormal m LED not lit Check the power supply and cabling If power is available and the LED stays off call Verint Video Solutions technic
95. twork configuration from a server For more information about DHCP see Appendix C on page 65 You can set this option only if the S1100w is connected to a network that uses a DHCP server Verint Video Solutions 47 4 Setting Parameters with the CLI Local IP Address The IP address is the identifier of the S1100w on the network The IP address format is a 32 bit numeric address written as four numbers separated by periods Each number is in the 0 255 range Each device on a network must have a unique IP address Subnet Mask The subnet mask is the binary configuration specifying in which subnet the IP address of the device belongs A subnet is a portion of a network that shares a common address component On TCP IP networks a subnet is defined as a group of devices whose IP addresses have the same prefix Unless otherwise specified by your network administrator it is recommended to use a subnet mask of 255 255 255 0 Gateway The gateway represents a network point that acts as an entrance to another network Warning Never use the IP address of the device as the gateway value Ping Request Ping is a basic Internet program that allows you to check that a particular IP address exists and can accept requests To ping a specific device 1 Inthe Ping Request Send Buffer Size parameter enter the buffer size in bytes 2 In the Ping Request Target parameter enter the IP address of the device 3 Execute the Ping Remo
96. ude a Radiant digital video motion detection DVMD module for motion tracking The specific module embedded into the S1100w MT devices DVMD 1 is a single channel product that will work with one video input You perform the DVMD configuration with the Radiant ManagerNET application The configuration process includes Configuring the serial port Creating a connection for the DVMD module Configuring the DVMD module Updating the firmware of the DVMD module If the S1100w MT device is used with the nDVR software all events relative to motion detection are sent to the digital input 3 entity Verint Video Solutions 83 H Motion Track Motion Detection Processing Using adaptive signal processing technology the DVMD module achieves a high probability of detection in a wide range of operating environments with a very low nuisance alarm rate This technology is especially good at handling noisy video sources such as uncooled infrared and light intensified cameras DVMD adapts to changes in lighting and weather that have caused previous generations of video motion detectors to generate a high level of nuisance alarms Because DVMD works with any NTSC or PAL camera it greatly enhances the effectiveness of video based security systems operating in a wide range of indoor and outdoor environments The heart of the DVMD technology is the video processor which executes the Radiant proprietary algorithms All DVMD firmware user setting
97. vice connected to the S1100w device For instance when configuring the device you must unplug any RS 422 485 device Power Use the red and black wire pair of the CAB9P cable to connect the S1100w device to an external power supply To power an S1100w device 1 In 12V DC the red wire is for input and the black wire is for power ground a Twist together the black power wire of the cable and the wire with the dashed white lines of the supplied power supply b Twist together the red power wire of the cable and the other power supply wire 2 In 24V AC both wires are used for power Connect the two power wires of the cable to the screws labelled 1 and 3 on the power supply it does not matter which wire goes on which screw Configuring the Wireless System The configuration steps to execute are m Set a series of parameters m If required establish a point to point connection between the transmitter and a receiver Verint Video Solutions 25 3 Configuring and Installing the Device To configure the device you need the proprietary SConfigurator tool It is included on the SmartSight Utilities CD shipped with your device you can also find its latest version on the Verint Video Solutions extranet Technical Support gt Downloads gt Firmware Upgrades You have to copy its executable file to the hard disk of your computer Computer Requirements The minimum hardware and software requirements for the host computer n

S1100w User Manual.book

Contents

Download Pdf Manuals

Related Search

Related Contents