User manual – N. 2 – 2004
Contents
1. Depth can be further reduced loose bolt 15 and remove the tray Loose screw from bolt 16 and take off the metal tube from holder 17 Turn upside down the holder fit it into its place and then fit again the tube Safely screw in hole 16 fit again the tray in the holder and tighten bolt Pict Lateral position Loose bolt 15 with the proper key and place the tray to the required position according to the sliding mechanism Properly tighten bolt 15 and make sure it is safe and tight Swing Away 14 Loose wing screw 14 raise the right side of the table and tilt it to left until it is next to the seating unit MITICO ATTENTION Maximum load of the tray 5 kg Pict 14 39 Pict L1 MULTIFUNCTIONAL TRAY Depth adjustable table with a wide surface area Fit on armrests pict L2 L3 Loose wing screws J of the armrests and fit the tray bars into armrest hole Z Then properly tighten screws J and make sure it is well fixed Armrests removal Carry out opposite process to the fitting operations WARNING Before fitting the tray be sure armrests are at the same height WARNING pict L3 The tray is supplied with supports 18 at ADJUSTMENTS such a distance that it can be used on Depth pict L2 medium seating unit To adapt to a smaller Loose wing screws J and place the tray to the required position tighten size invert the position of two supports 18 screws J Make2. need If the exceeding part is too long it can be cut and sealed with a small flame 54 5 W Hanging bags on pushbar could alter the stability of the frame While folding and unfolding the frame some metallic parts can contact causing damage to paintwork Be careful not to trap one s own fingers Be sure that all joints screws and levers are well fastened after the necessary adjustments Take care of the child while in the Mitico system Grounds with more than 10 inclination can endanger the frame balance Be careful on uneven slopes 55 ANNUAL MAINTENANCE Mitico seating system does not need any particular maintenance an annual check up of mechanical parts by specilized personnel is suggested As well it is recommended to clean and polish wheels to take off dust and dirty particles which could brake or block wheels movements FABRICS CLEANING Mitico fabrics and paddings can be washed by hand or in washing machine at max 40 C with usual mild detergents Armrest can be cleaded by means of a mild spray not agressive like thinner or trichlorethylene SCREWS AND BOLTS Screws and bolts could be loosened over time Therefore do not forget to monitor check them regularly and if necessary tighten them properly If safety locks loosen they may lose their main function therefore they have to be replaced with new ones CAUTIONS FOR THE SEATING SYSTEM Mitico should
3. footplate To modify the positioning range disassemble the chromed iron part under the footplate and assemble it as shown in the picture 25 L ALTALENA Swing Frame pict B24 The frame allows the seating unit to swing See pages 8 9 for seating unit fitting and removal Frame setting For an easier and faster frame setting all parts have been given a corresponding letter the same as on the correspondent screws and joints Mount the elements of the frame by assembling the parts with each other All parts to be assembled are indicated by double letters that if correctly followed they will be next to the other B B etc For an easier mounting lay the first arch to the wall put the tube into the higher hole and the frame in the holes below then take the second arch and set all parts like the previous one fix them with their own bolts At this point the structure is ready and the swinging part has to be mounted with bolts into the bearings fix the frame to the central part of the structure DO NOT FORGET TO USE AT THIS POINT A PARTICULAR LOCKING DEVICE TO FIX THE BOLTS SECURELY Check the correct working of Swing Frame ATTENTION All parts have a slight backlash thus there is the possibility of more difficulties in putting them into place use a rubber hammer to prevent from varnish damaging 26 KE Pict B24 MOLLA Spring Frame pict B25 The spring frame allows seat oscillation See
4. Loose bolt 31 and place the single footplate at the required height strongly tighten the bolt Adduction pict M8 Loose bolt 30 and place the single footplate as required strongly tighten the bolt It is possible to achieve more or less adduction by inverting the sliding supports Swap from right to left side and refit onto 30A Inwards outwards rotation pict M10 Loose bolts 33 under the footplates and set as required tighten the bolts again WARNING Do not position the child stand on the plates they are not designed to support heavy weights Pict M10 46 CALF PANEL FOR INDIVIDUAL FOOTREST It supports the legs and spreads the legs weight over a wide surface height adjustable Fit on the footplates pict M12 Loose bolt 32 and bolts 31 of the plates and take off from the supporting frame Loosen bolt 35 under the legrest and slide on in the place of the two plates Tighten bolt 35 and replace the plates onto the support Tighten bolts 31 and bolt 32 Removal from the footplates Carry out opposite process to the fitting operations ADJUSTMENTS Height pict M12 Loosen bolt 35 of the legrest and set it at the required height then tighten the bolt again Cover It is removable and washable with a mild detergent 47 FRONTAL KNEE SUPPORTS Couple The frontal knee support is equipped with two rests covered with soft material adjustable in width depth height and angle Covers a
5. Maximum load 5 Kg in balanced weight distribution L ALTALENA Swing Frame 876004 Weight 37 kg Maximum load 40 kg MOLLA Spring Frame 876005 Weight 21 kg Maximum load 20 kg 61 DENTRO indoor frame 876005 Weight 12 kg Maximum load 50 kg Size see drawing Gas piston 350 N 62 FUORI outdoor frame 874004 Weight 13 5 kg Maximum load 50 kg Size see drawing Gas piston 350 N e e e N LN LN BUGGY outdoor frame 874001 2 Weight 874001 small size 12 5 kg 874002 medium size 13 kg Maximum load 874001 small size 40 kg 874002 medium size 40 kg Size 874001 small see drawing 874002 medium see drawing ROLLING outdoor frame 874101 2 Weight 874101 small size 10 4 kg 874102 medium size 10 4 kg Maximum load 874101 small size 40 kg 874102 medium size 40 kg Size 874101 small size see drawing 874102 medium size see drawing fumagalli Is distributed by 64
6. WORLD PREFACE This users manual presents all of the necessary information for the correct use and efficient maintenance of MITICO The ongoing research to improve and update our production may sometimes lead to changes therefore images and instructions of the present manual should not be considered strictly binding For accessories or new MITICO products which are not included in this users manual please refer to your local Mitico Dealer USE REMARK In order to enable the child to perform all activities safely it is required that all postural adjustments are carried out by specialized personnel physicians physiotherapists occupational Therapists etc The following state of the art products have been tested and comply the CE 93 42 norm Note that incorrect use or underestimated dangers can be the cause of damage and or accidents Fumagalli do not undertake any responsibility for accidents caused by any use which is not in accordance with the instructions In case of second hand postural systems Fumagalli do not undertake responsibility for possible changes or unauthorized parts replacements if you do not have the users manual please get in touch with your dealer or directly with Fumagalli We kindly ask you to check that your new goods in packages are not damaged by shipment this case get in touch as soon as possible with your Fumagalli dealer TARGET This product has been developed
7. appropriate elastic plugs Fix seating unit adaptor in the right position Pict B18 23 Pict B19 Frame s Folding pict B19 B20 B21 Remove the seat Release the adaptor by loosening the wing screw and take off the sliding bar Remove the elastic plugs that block the front wheel fork ATTENTION Do not carry out the above steps when the child is sitting Do not forget to fix the front fork by means of the two plugs Pict B20 ROLLING frame is developed to overcome little obstacles side walks put one s foot on the support bar between the rear wheels and push downwards the handle to overcome the obstacle At the same time raise rear wheels and push ROLLING frame on the ground Do not forget to block the frame with the appropriate parking brakes when you stop MITICO Do not use MITICO system on slopes exceeding 10 24 BRAKE 22 To stop the frame pull the lever the pushbar handle Parking brake To block brakes completely push the brake lever and raise the parking brake lever release brake lever and check that the parking block is correctly set in To unblock the brake slightly press on brake lever to release the parking lever Pict B22 Footrest adjustment pict B23 The footrest with Velcro straps for feet positioning can be adjusted by loosening the wing screws behind and then by sliding it It is possible to set the foot support by unscrewing the bolt under the
8. at the push handle and raise it up to end position Tighten levers E and adjust push bar handle position tighten levers G ATTENTION The push bar handle can spin to 360 Check that brakes wires do not wrap around the push bar while turning it Pict B14 20 Frame folding 14 15 Take off the seating unit and release levers I L to loose the gas piston and recline the adapter Loose levers E G on the push Move the pushbar towards the front wheels Lower the pushbar handle under the support arch of front wheels lower completely the push bar Tighten levers E and G Before folding the frame do not forget that the adapter plates must stay in a horizontal position otherwise the frame could be damaged ATTENTION Loose levers I and L to have the gas piston opened Otherwise bars could be damaged during frame folding 21 Pict B15 Do not carry out the above steps when the child is sitting The handle of push bar can spin to 360 Please be careful that while placing the handle brake wires do not wrap around the push bar Take off the seating unit adapter to reduce the frame volume Unscrew and remove handle H then detach the seat adaptor FUORI frame is developed to overcome little obstacles side walks put one s foot on the support bar between the rear wheels push downwards the handle to overcome with front wheels the obstacle At th
9. cover and bolts O place the headrest and bolt T tighten all bolts Position the braces on the seating unit Fix the lower harnesses already set on the seat in locks 46 of the braces Removal from the seating unit Carry out opposite process to the fitting operations 52 Q2 CHEST VEST USE Q3 Loose the braces from the higher locks by pressing 47 then unzip Let the child sit in the seating unit then put the harnesses into place by higher locks 47 Close the zip and adjust the harnesses according to child s dimensions NOTE Harnesses are produced long to be adjusted according to children need If the exceeding part is too long it can be cut and sealed with a small flame ANATOMIC PELVIC ABDUCTION BELT It keeps legs abduction and monitor the pelvis to prevent from sliding forwards All parts are washable according to label s instructions Fit on the seating unit pict R1 R2 Place the belt on the seat with the coloured side downwards Put the harnesses in holes Y of the seat and the male side to the other two free harnesses in the seat Removal from the seating unit Carry out opposite process to the fitting operations 53 ABDUCTOR STRAP USE R2 Let the child sit in the seating unit then pass the two belts between the legs and use locks 48 to fix Adjust the harnesses according to child s needs NOTE Harnesses are produced long to be adjusted according to children
10. needs NOTE Turn support K 180 to put further forwards or lower the headrest 30 WING SIDE AND SHAPEABLE HEADREST The anatomic and shapeable or wing side shapeable headrests are equipped with a support that allows the best performance for their shaping possibilities Mount and remove them by enclosing the chromed vertical bar in the fitting on the back side of the seat fix with the Allen key ADJUSTMENTS pict D7 Every adjustment is made by action on two wing screws A that fix the ball joints and by wing screw B that fix the depth of the headrest Loose the screws find the most suitable position and fasten them all NOTE When bar C is projecting too much cut it after unscrewing black knob and then replace the rubber bush on the bar Strain The structure of the headrest is made up of a thin steel plate that can be shaped just by hand That allows customizing the headrest according to the needs of the child Cover Cover is removable and washable according to the indications on the label 31 If the child needs a further support to prevent one s head from falling forwards they can use the cap It can be used together with all Mitico anatomic headrests and the neckrests too moreover the cap can be used with other headrests thanks to its fitting system In this case just few modifications are needed Cap Fitting ADJUSTMENTS The cap position can be adjusted by mea
11. not be used with temperatures lower than 35 C or higher then 60 C There is no limit of use in humid or dry air conditions REPAIR With the exception of secondary repairs all other maintenance work should be carried out by technical personnel at your nearest supplier For all information on repair and after sales services please contact the distributor in your area SPARE PARTS Refer to your nearest supplier for accessories and spare parts WASTE DISPOSAL RECYCLING The packing material is to be recycled The metallic parts can be recycled as old metal material PRODUCT RE USE Mitico is developed to be used more than once time at this aim a kit for re use is available The kit includes covers and padding to be replaced at each new use and Mitico application Your supplier will be pleased to give you all necessary information on this point 56 GUARANTEE CERTIFICATE Fumagalli products are made according to the most modern technologies Product parts are of top quality and grant stability for a long time In case the product shows lack of quality materials or processing under normal conditions we will then destroy and replace it in compliance with the guarantee guidelines In case you bought Miitco in the European Union members you can take the damaged faulty product to one of the official Fumagalli distributors together with the guarantee certificate In case of purchase outside the European Union refer to the retailer
12. of spring effect pump and unload the piston rise up to the highest level and completely lower the seating unit by lever E 13 Pict B2 PUSHBAR DENTRO INDOOR FRAME Pushbar fitting Pict B4 The Dentro indoor frame can be fitted with a pushbar for indoor mobility Unscrew the black knobs A slide the bars into the frame holes screw in and tighten screws A Removal of pushbar To remove the pushbar remove screws A and pull upwards the pushbar Adjustment of pushbar inclination Pict B3 Loosen screws B adjust the pushbar into the necessary position and height and then tighten again the screws ATTENTION Before all fitting operations do not forget to brake all 4 castors The Dentro indoor frame is not suitable for outdoor use or to overcome obstacles Mitico system may be used only on safe even and reaiular araiunds 14 BUGGY outdoor frame Frame for outdoors Folding outdoor frame with front pirouetting wheels and foot brakes on back wheels It allows tilt in space See pages 8 9 for seating unit fitting and removal Frame unfolding pict B6 B7 Lay the frame with the wheels on the ground and raise the push handle while keeping plastic rings E raised up near the push handle Fix the frame by pushing rings E down into position Put tilting bar F in the adapter G and fix with lever H NOTE A For a better position of lever H without changing bolt eek a PN tens
13. the desired shell side support distance It is necessary to remove the padding from backrest to carry out these operations Screws in different lengths are to be found standard in the packing and must be used if width adjustments are required Once the new width is achieved refit all of the padding ATTENTION pict A4 Do not tighten too much bolts Q to avoid difficult armrests adjustments 10 ARMRESTS Pict 4 Inclination and height adjustment Take off bolt S to change the height after removing backrest padding Place the armrest in the desired hole and fit it again with the bolt Inclination is adjustable by unscrewing wing screw N finding the new angle tightening screw N and also bolt Q COVERS pict 5 Covers can be taken off and washed according the instructions on their labels Under the seat cover there is a pocket that enables the addition of a further padding POSTURAL WEDGES pict 6 Some wedges are supplied that can be shaped according to one s needs These can be attached with Velcro to the backrest and seat cushions ATTENTION The use and placing of wedges must be carried out only by specialized personnel physicians physiotherapists occupational therapists etc 11 Pict 5 Pict A6 DENTRO Indoor frame Indoor frame with four castors with brakes Seat to floor height and tilt in space is adjustable See pages 8 9 for seating unit fitting and removal ADJUS
14. the wing screw D on the rear side Pict A1 Pict A2 Frames removal 2 Loose the wing screw D pull knob C downwards push the seat forwards ATTENTION Do not carry out the above steps when the child is sitting Do not use the armrests to displace the seating unit as they can detach Before all fitting operations do not forget to brake all the wheels BACKREST Recline adjustment pict A3 To recline the backrest loose lever L find the seat to back angle required then screw it to fix the backrest angle You can pull the lever out slightly and move it without changing the tension on the screw so that it can be tightly secured and moved into a safe position Length adjustment pict A4 Remove the padding and the cushion from the backrest Take off the side bolts O and place the extension at the requested height in the right hole Insert and tighten the bolts Re attach the cushion and the padding Pict A3 SEATING Depth adjustment pict A4 Remove all padding Loose the bolts P and place the seat extension as required Replace and tighten the bolts Width adjustment pict A4 The gap between the two padded side supports is adjustable also asymmetrically Green disks M between the side support and the steel shell can be easily added and removed Each disk is 10mm thick Unscrew bolts Q and R insert or take off the disks and reassemble the part by choosing a suitable bolt for
15. 28 Lum TEREPE AUSILT Pontelambro Co P za Puecher 2 39 0 31 3356811 A e 0 31 622111 www fumagalli org me Thank you for choosing as your new colourful postural seat Mitico is the result of extensive research and specific know how in regards to children s equipment It supports their bodies in a careful and comfortable way The range of available colors accessories and materials guarantees that Mitico is individualized for the child In the following pages you will find all of the characteristics and instructions on your MITICO Please Read It INDEX Before exploring the world of Mitico Seat Postura Postural seating unit seat and back Dentro indoor frame Buggy outdoor frame Fuori outdoor frame Rolling outdoor frame L Altalena swing frame Molla spring frame Mitico roof Headrests Cap Shoulder stabilizer Swing Away Side Support Abductor Bumper bar Transparent front tray Multifunctional tray Platform Style Legrest for platform Style Single platform Legrest for single platform Separate footrest Legrest for separate footrest Frontal knee supports 45 belt with braces 45 pelvic belt Vest with braces Anatomic pelvic abduction belt Attention Notes Maintenance Labelling Guarantee Soft and washable cower warm and comfortable by Systems developed to fix braces bel
16. F PANEL FOR SINGLE PLATFORM Provides support to legs and spreads the legs weight over a wide surface height adjustable Fitting the footrest pict M6 Loose bolt 27 of the footrest and take it off the structure Loose bolt 28 behind the legrest and fit it onto the footrest site Tighten bolt 28 and refit the footrest to the structure then tighten bolt 27 again Removal from thefootrest Carry out opposite process to the fitting operations ADJUSTMENTS Height pict M6 Loosen bolt 28 of the legrest and place it to the required height then tighten the bolt Cover It is completely removable and can be washed with a mild detergent 44 Pict M6 INDIVIDUAL FOOTREST Pict M7 It is made up of a rigid structure with two individual footrests Both footrests are independently adjustable in height inward and outward rotation lateral and depth adjustment The footrests are equipped with Velcro straps removable and washable to fix one s feet Fit on the frame pict M7 Loosen bolt W on the frame and insert the square tube of the footrest Tighten safely bolt W Removal from the frame Carry out opposite process to the fitting operations ADJUSTMENTS Supporting frame Angle adjustment pict M8 Loosen bolt 29 and angle the frame as required then strongly tighten the bolt 45 Footplates Angle adjustment pict M10 Loosen bolt 34 and angle the single footplate as required Tighten the bolt Height pict M8
17. TMENTS Height pict B1 Repeatedly press lever E with one s foot in the rear part of the frame to reach the requested height To decrease height level keep lever E completely pressed until the unit comes down to the required position If the seating unit does not low press it down by hand gently Tilting pict B2 The seating unit tilting angle is controlled by a gas piston under the frame adaptor B tilt back by raising the lever F and push backwards the seating unit and tilt forward lowering the lever and take forwards the seating unit Rotating wheels pict B1 Mitico system is equipped with four braked castors This braking system stops the rotating and the pirouetting movements of each wheel To fix the wheels push downwards on brakes G Lift upwards to release brakes 12 Pict B1 Do not lift the seating system MITCO by the seating unit NEVER load one s weight on lever E just lower it The DENTRO indoor frame is not designed for outdoor use or obstacles When you stay with MITICO seating system do not forget to brake the frame with its four braked castors Mitico system may be used only on safe even and regular grounds Before all fitting operations do not forget to brake all 4 castors ATTENTION Air can enter the little piston which adjusts the height and this could cause springing in the seat For this kind of shifting remove and replace the seating unit In case
18. ar handle can spin to 360 Please be careful that while placing the handle brake wires do not wrap around the pushbar 18 4 Handle Pict B11 Tilting B12 The seat tilting angle is controlled by the lever under the frame adapter B chair can be tilted back by raising lever F push backwards the seating unit or can be tilted forward take forwards the seating unit Seating unit turn pict B13 The seating unit be placed so that the child can look at the street or at the caregiver Pict B13 To invert the direction unscrew and remove bolt H take off the support system of the seat and revolve by 180 Insert the support mechanism in the new position on the frame replace and tighten bolt H ATTENTION Do not carry out these operations while seating unit is attached on the frame 19 HINWEIS Durch leichtes Anheben kann der Klemmhebel G in eine gew nschte Position geschwenkt werden ohne die Arretierung der Sitzneigung aufzuheben Dazu den unteren Anteil des Schwenkhebels festhalten und den oberen Teil in die gew nschte Position drehen NOTE With a light pull lever G can be moved into a more appropriate position without changing the tension on the bolt The lower part of the lever remains fixed while the upper part pulls out and moves into a better position Frame Unfolding pict B14 Lay the frame with wheels on the ground loose levers E and
19. ct D2 Pict D1 HEADRESTS n NeckRest pict D1 Anatomic head postural unit pict D2 Winged side shapeable head postural unit pict D3 Cap front rear forehead support pict D4 shapeable head postural unit pict D5 There are different models to suit the child s needs Possible adjustments are the same for all of them height depth inclination and lateral position can be adjusted Ndt io qui metterei magari codici articolo NOTE For the winged side shapeable postural head unit and the support and shapeable head postural unit shapes can be modified due to their light alloy structure Pict D4 Fitting on the seating unit pict D6 Loose bolt T and put the bar of the headrest into the rear support of the Pict D6 backrest then tighten the bolt Removal from the seating unit pict D6 Carry out opposite process to the fitting operations ADJUSTMENTS pict D6 All the Headrests are height depth angle and laterally adjustable by using the following bolts T Height adjustment 1 Depth adjustment 2 Lateral position adjustment 3 Angle adjustment All bolts can be loosened and fastened with the enclosed Allen key COVER Covers are removable and washable according to the indications on the label ADDITIONAL WEDGES The headrests are equipped with additional wedges that can be inserted under the cover when the support has to be modified as per the child s
20. e same time rise up rear wheels and push FUORI frame on the ground Do not forget to block the frame with the appropriate parking brakes when you stop MITICO Do not use MITICO system on slopes exceeding 10 BRAKE pict B16 To brake the frame press lever 11 toward the push bar handle each braking system is independent and allows you to slow down or stop only the necessary wheel Parking brake pict B17 To block brakes completely push brake lever I1 and raise the parking brake 12 release brake lever 11 and check that the parking block is correctly set in To unblock the brake slightly press on lever I1 to release the parking lever 12 22 ROLLING outdoor frame Outdoor foldable frame rear wheels with drum brake Modern design It guarantees an efficient aid to be used outdoor even on uneven grounds See pages 8 9 for seating unit fitting and removal ADJUSTMENTS B18 Tilting The tilting angle is managed by the wing screw J under the frame adaptor tilt back by loosing it push backwards the seating unit or tilt forward push forwards the seating unit Be careful that the wing screw is set in one of the holes on the sliding bar then tighten again lever J Frame s unfolding pict B19 B20 B21 Lay the frame with wheels on the ground and follow the indicated operations Raise the mobile part according to the allowed movements Set the front fork in the hole on the wheel pin and fix with the
21. for children who need a modular postural system to be used both indoors and outdoors MAINTENANCE The device does not require a specific maintenance program however for a long lasting product we suggest a yearly check up of all mobile mechanical parts joints brakes wheels couplings etc These parts have to be carefully lubricated with spray grease Clean with a damp cloth or mild detergent Do not use nitrocellulose or polyurethane solvents SEATING UNIT POSTURA Postural seating unit seat amp back It is made up Height adjustable and inclinable backrest m Depth and width adjustable seat 7 Armrest movement synchronized with backrest adjustable in height and angle One adaptor suitable for all Mitico frames Padding made up of removable and machine washable cover Various accessories available to satisfy all needs The seating unit is standard assembled with proper adjustments in order to get the smallest volume for shipment Before using Mitico ensure that you have carried out your own further adjustments for the individual user Fitting on frames pict A2 The adaptor under the seating unit is the same for each Mitico frame therefore the seating unit can interface all frames Have the two plates join i e seat pan and interface plate Lay sliding surface A of the seating unit on adaptor B of the frame and let it slide up until pin C clicks into place Fix the seating unit by tightening
22. imultaneous adjustments of depth width and rotation are allowed Once adjusted tighten the bolts WARNING Do not position the child while standing on the footrest it is not developed to support heavy weights CALF PANEL FOR PLATFORM STYLE Provides support for the legs and spreads the load on a wide surface height adjustable Fit on footrest pict M3 Press the legrest on Velcro 24 of the platform structure Removal from the footrest Carry out opposite process to the fitting operations COVER It is completely removable and can be washed with a mild detergent PictM3 42 SINGLE PLATFORM It is made up of a metal supporting structure and a footrest with foot straps The structure is angle adjustable The footrest is height and angle adjustable Fit on the frame pict M4 Loosen bolt W on the frame and slide in the square tube of the footrest Tighten safely bolt W Removal from the frame Carry out opposite process to the fitting operations ADJUSMENTS Supporting frame Angle pict M4 Loosen bolt 25 and angle the structure as required then tighten the bolt again Footrest Angle pict M46 Loosen bolt 26 and angle the footrest as required then tighten the bolt again Height pict M4 Loosen bolt 27 and place the footrest at the required height then tighten the bolt WARNING Do not position the child standing on the footrest it is not developed to support heavy weights Pict M4 25 CAL
23. instructions on its label ATTENTION The abductor should not be used as pelvic block but to keep hips abducted 36 BUMPER BAR Arm support adjustable in depth and adaptable to the different positions of the armrests Fit on the seating unit pict H2 Fit the two bar ends in armrest holes Z and secure with wing screws J Removal from the seating unit H2 Carry out opposite process to the fitting operations ADJUSTMENT pict H2 Depth Loose screws J and put into place as required fasten the screws again ATTENTION If it isn t possible to fit the bar completely check that screws J under the armrests are properly loosened Be sure that screws J are acting upon the bumper bar 37 Pict H1 TRANSPARENT FRONT TRAY Transparent front tray is flip away and adjustable in depth and lateral position Fit on armrests 12 Loose screw J of left armrest and fit the tray bar in hole Z of the armrest Properly tighten screw J and be sure of its tightness Remove from the arm rests pict 12 Carry out opposite process to the fitting operations ADJUTMENTS Depth pict 11 Loose screw J and put the tray into the required position tighten screw J ATTENTION 9 sure that the table attachment is properly blocked by screw J To avoid damaging during shipment the table is equipped with a protection film which should be removed before use Pict I2 NOTES
24. ion pull it outwards and lay it as desired m redi AI Pict B7 15 Frame folding B6 B7 Remove the seating unit see Seat removal and brake the frame Loose lever H unhook rings E and keep them near the handle bar Then shift the push bar toward the front wheels ATTENTION Do not carry out the above steps when the child is sitting Do not forget to fix the frame with the appropriate parking brakes when you stop Mitico Before closing the frame loose lever H otherwise the structure could be damaged Pict B8 ADJUSTMENTS Tilting pict B6 The seat tilt angle is controlled by lever H under the frame adapter the angle can be increased by loosing lever H and pushing backwards the seating unit or can be decreased taking forwards the seating unit BRAKE pict B9 To stop the frame push down on pedal I both rear wheels will stop To remove brakes push on pedal I 16 17 FUORI outdoor frame Frame for outdoors Folding outdoor frame with front pirouetting wheels and brakes on back wheels It enables the seat to face either towards the street or towards the caregiver and it is equipped with tilt in space It is equipped with springs for shock absorbtion for use on uneven ground See pages 8 9 for seating unit fitting and removal ADJUSTMENTS Handle inclination pict B11 Loose levers G and place the handle as per one s needs tighten the levers ATTENTION The pushb
25. nder guarantee if the above listed documents are missing or if products have been changed and modified since the purchase date 5 2 This guarantee does not replace or report on any damage caused in case this product has to be modified or adapted in 3 4 __ 5 6 order to respect national or local technical safety norms in a country different from the one where it had been manufactured The present certificate is not valid if series number or model have been changed cancelled or have been made unreadable The present guarantee does not cover the following points Regular maintenance and parts repair or replacement due to normal wear Those changes and adjustments to the product without the written authorization by Fumagalli Srl and different from the ones given in the user manual Damages of the product caused by Inproper use particularly Product use for different aims from the given ones or use without respect of Fumagalli Srl user manual and terms The use of the product in a way that in the country where it is used does not correspond to safety and technical norms Unsuitable or innappropriate set up b inproper and not suitable cleaning or maintenance repairing by unauthorised Cervice Senters or by customers themselves d Faults accidents changes to set up processes or wrong packing use of non original spare parts e Faults water fire high tension not necessary and regular electrical supply u
26. ns of its Velcro and its own features 32 SHOULDER STABILIZER The stabilizer allows to control the child s upper body trunk It is made up of a stiff structure and of two lateral padded supports All the parts are washable L Pict E1 Fit on headrest pict E1 Loose bolt T and take away the headrest Unscrew bolt 4 and fit the shoulder stabilizer onto the headrest bar tighten bolt 4 Fit again the headrest into its hole and tighten bolt T Remove from headrest pict E1 Carry out opposite process to the fitting operations ADJUSTMENTS Height pict E1 Loose bolt 4 and put the shoulder stabilizer at the needed height tighten bolt 4 Depth pict E1 Loose bolts 5 and put into position the thoracic support bars according to one s needs then tighten bolts 5 Shape pict E2 Thanks to the shapeability of the head support plate it is possible to form and customize them according to the individual needs 33 SWING AWAY SIDE SUPPORT Lateral trunk support individually adjustable in height width and shape with quick release swing away mechanism Pict F1 Fit on seating unit pict F1 F2 F3 Remove the padding and the cushion from the backrest Adjust the square nut 6 and the side support 7 into the backrest screw in the correct position using bolt 8 and the green washer Fix again the padding on the backrest and the thoracic support 9 in hole 7 Remove from the seating unit Carry out opposite p
27. nsufficient air and all other situations that are not Fumagalli Srl reponsabilty f System defects linked to this product g Use of spare parts produced by another manufacturer and not in compliance with Mitico product The above guarantee does not cover products used and showed during exhibitions business meetings seminars or similar events Fumagalli Srl and authorized distributors are not responsible for damages caused by things animals or people by their own environments The above guarantee is limited to legal rights of users in compliance with the current valid national laws and to the contract between the user and the retailer 58 For any further technical help on the product please contact PRODUCT Series Number Producer stamp and signature Purchase Date Name and address of the customer ADDITIONAL GUARANTEE 59 TECHNICAL DETAILS SEATING UNIT 873002 3 TRUNK PELVIS POSTURALSEATING UNIT WEIGHT 873002 small see drawing 873003 medium see drawing SIZE 873002 small see drawing 873003 medium see drawing COVER FabricTREVIRA CS fire retardant and very transpiration friendly Hand washing with usual and neutral detergents do not iron PADDING Closed cell sylicon fibre 17 Denier very transpiration friendly Hand washing with usual and neutral detergents do not iron 60 TRANSPARENT FRONT TRAY 870041 Maximum load 5 Kg in balanced weight distribution MULTIFUNCTIONAL TRAY 870043
28. pages 8 9 for seating unit fitting and removal NOTE For maintenance a regular check of all bolts joints and bearings lubrication is strongly recommended ATTENTION Do not set the frame while the child is sitting Do not use the armrests to move the seating unit since they can also unlock It is suggested to use with the bumper bar and a fixing device vest or belt Do not keep the frame outdoor in a humid place or exposed to bad weather conditions The ALTALENA Swing and MOLLA Spring frames have to be used with seating unit Mitico only and under the assistance of expert staff 27 Pict 25 MITICO ROOF Mitico roof can be fitted on all Mitico seating units with outdoor frames It is easy to assemble and very useful outside equipped with rain protection covering and joint to allow the roof to be pushed backwards Fitting Pict C1 C2 The seating units are equipped with side holes to assemble the two plastic supports use the bolts and fix them inside the back support then fit the roof by inserting the chromed tubes into the supports Removal Carry out the opposite process to the fitting operations ATTENTION Each seating unit is equipped with holes at different height to enable roof to be fitted where needed Use A joint to allow backwards movement characterizes the roof The rain protection covering will be mounted using the apposite buttons on the roof Pict C2 28 Pi
29. re removable and washable Fitting on the frame pict 85 Loose bolt W and take off the footrest Loose bolt 36 of the knee support and fit it in the footrest bar Tighten bolt 36 and fit again the footrest Tighten bolt W Removal from the frame Carry out opposite process to the fitting operations ADJUSTMENTS Height pict N1 N2 Loosen bolts 37 and set knee support as required then tighten the bolts again Width pict N1 N2 Loosen bolts 37 and adjust the support width tighten the bolts again 48 Pict N2 Depth picture 1 2 Loosen bolt 38 place the knee supports at the required depth tighten bolts again Angle and lateral adjustment pict N1 N2 Loosen bolts 39 and position the supports as required tighten the bolts again Shape It is possible to customize the support by shaping the soft part H HARNESS 45 belt with braces to fix the trunk and the pelvis to the seating unit in a comfortable way The whole belt can be washed as per instructions on the label Fit on the seating unit pict O1 O2 Remove the headrest and bolts O and T then take off the plastic cover Insert and fix the higher harnesses in the suitable holes X of the seating unit Fit in the plastic cover and bolts O then place again headrest and bolt T tighten all bolts Position the braces on the seating unit Fix the lower harnesses already set on the seat in holes 40 of the braces Removal from the seating unit Carr
30. rocess to the fitting operations ATTENTION Use and positioning can be carried out only by experts professional staff Assure that the square base of nut 6 is always correctly fitted into Pict F3 ADJUSTMENTS Width and height pict 59 Swing away side supports are adjustable in height and width by use of bolt 8 that fix support 7 Loose the bolt move the support to the proper position and tighten bolt 8 QUICK RELEASE pict F3 The side support quick release and positioning are carried out by use of button 9 pull forwards to unblock the side support It will automatically lock again when put into place Shape The supports can be shaped put the plastic part into warm water until it becomes malleable Now they can be shaped according to one s needs COVERS They are removable and washable according to the instructions on their labels 35 ABDUCTOR Depth adjustable abductor with removable and washable cover Fit on the seating unit pict G2 Fit the support 11 in hole V under the seat fix with bolts 12 Fit the abductor in hole 11 and secure with bolt 13 Remove from the seating unit pict G2 Loosen bolt 13 and take out the abductor If it has to be removed in a permanent way support 11 can be left in its place ADJUSTMENT pict G2 Depth Loosen bolt 13 and put into place the abductor according to one s needs Tighten the bolt again Pict G1 COVER Cover is removable and washable according to the
31. sure clutches 18 are secured by screw J under the tray remove bolts 19 and invert the right with the left one while keeping the same direction By this way it gets narrower and width is adapted to the armresis distance of the smaller seating unit Bolts 19 that fix the supports are loosening to be adapted to the armrests gap Once you have adjusted the tray in tne right iti anfah position fasten them S Before using the covering layer remove the protection film on it 40 PLATFORM STYLE It is made up of a metal supporting structure and a footrest equipped with heel cup The metal structure is adjustable in angle and length The footrest is adjustable in angle Every heel cup is adjustable in width depth and rotation Fit on the frame pict M1 Loose bolt W on the frame and slide in the higher part of the platform Tighten safely bolt W again Removal from the frame Carry out opposite process to the fitting operations ADJUSTMENTS Supporting structure Angle adjustment pict M1 Loose the quick relay 20 and angle the structure as required Tighten again the relay Length pict M1 Loosen the pommel 21 and set the platform at the required height to the correct hole Tighten the pommel 41 Pict M1 FOOTREST ANGLE ADJUSTMENT Loose the quick relay under the plate and angle it as required Tighten again the relay HEEL CUPS TOE STRAPS pict M2 By loosening bolts 23 under the footplate s
32. ts athar fixing touch and sight ways Hicon hollow fiber padding braathabla press ion relief E Petyurothana and c load call support with adh asivae and maintenance by washing machina o to fe Velcro wedges 14 Amrosi af molded foam anbodied and hiddan firing E Easy backrest haight adjustmant and adjustment systems JE Eketo and removable covers af pelvis contanmants to 4 Shaped supports to be customized for lateral and or customize tha supports lumbar pushes and containment Saat of weccsa alastic and thanmaly shaped materia Declinabke backrest with zip at hig haight t koop the Declinable backrost with zip at hi haight to kasp to grant comfort and stability 46 angle ketasan dorsal pushes Polymeric and colored buckle aesthetic and functional Aj Customized abductor wedge alkct ib Saat depth os by mliding ta find tha camact Gp Di fara ntiated adjustment cf pa lateral containment position when the chi possibility ip customize 7 Jg Raar and forsard angling of tha seating unit Height adjustment by pedal pneumatic pump 120 Frame shape to allow the best sido approach for bet ber communications and to improwe relitiorehipe Fiubbar protectio g ar p ri with Soft fr fa and 1 10 ame cura Sard ancd mege Possible differant footrasts for ovary noad Pump protection ekaan Pup Four directional whale BEFORE EXPLORING THE MITICO
33. where you directly bought the seating system VERY IMPORTANT Do not forget to show the guarantee certificate together withinvoice or purchase receipt provided by the retailer GUARANTEE With the above guarantee Fumagalli Srl guarantee this product won t give any faults in materials and production for 2 years from the date of purchase Fumagalli cannot allow any other guarantee on the product therefore the customer must test in this certificate the respect for this norm In case product material or production faults arise during the guarantee term Fumagalli Srl or the offical distributor will repair the product itself replace or repair the faulty part without any charges and according to the guarantee conditions after being checked by Fumagalli srl Fumagalli Srl reserve the right to replace and change the parts of faulty units after necessary controls or to replace the product in case it cannot be repaired anymore Fumagalli Srl guarantee nothing more than what is written in this certificate TERMS 1 order to be provided with all guarantee services the following documents have to be enclosed with the certificate Your name and complete address The invoice of the EU supplier where you purchased the item with the purchase date on OR The complete name and address of your supplier where the product was purchased The series number and model of the item Fumagalli Srl reserve the right to refuse repair or replacement u
34. y out opposite process to the fitting operations 49 H HARNESS USE 03 Unlock the braces by pressing locks 41 and 42 Let the child sit then fit the braces to the higher locks with closures 41 Link the two braces with hook 42 Adjust the harnesses with rings 43 according to the child s body NOTE Harnesses are produced long to be adjusted according to children need If the exceeding part is too long it can be cut and sealed with a small flame 50 45 PELVIC BELT It controls the pelvic area and prevents the childt from sliding forwards Fit on the seating unit pict P1 Set the pelvic belt on the seat with the coloured part upwards Put the harnesses into holes Y of the seat Removal from the seating unit Carry out opposite process to the fitting operations USE pict P2 Loose lock 44 Seat the child properly then close lock 44 Adjust the straps with their rings 45 according to the child s needs NOTE Harnesses are produced long to be adjusted according to children need If the exceeding part is too long it can be cut and sealed with a small flame VEST WITH BRACES It supports and contains the child s trunk to the seat in a comfortable way All parts are washable according to label s instructions Fit on the seating unit pict Q1 Q2 Remove the headrest and bolts O and T then the plastic cover Fix the higher harnesses in holes X of the seating unit Fit in again the plastic
Download Pdf Manuals
Related Search