User's Manual
Contents
1. hers eus 8 Creme L NH CAUTION CAUTION DO NOT OPEN OPE NLY IF QUALIFIED EQUIPMENT TO RAIN OR MOISTURE ii Channel 1 Channel 1 ATTENTION This unit must be protected from damp because of the risk of fire and the possibility of electric shocks 1 Make sure that you have the correct mains voltage Only operate the unit at the mains Bridge Mode voltage marked on the rear panel Before setting the mode please turn off the amplifier and slide the 2 especially metal objects lo vies s sam 2 Make sure that nothing especially no metal objects are inserted into the device Thi mode select switch to above Picture 2 channel 1 and channel 2 Ed J could result in electric shock or malfunction are bridged At time the signal input into channel 1 will be output M from the bridge end On other hand the output level control of mad 3 If the unit is subjected to extreme fluctuations of temperature e g On being transported channel 2 should be turn down to smallest Only the volume E from outside into a heated room condensation can form The unit should not be used until control of channel 1 are used to control the volume of whole Ea ithas reached room temperature system HR 4 In the event of water or any other fluid being accidentally spilt on the unit switch the unit off immediately and send it to a qualified service workshop for inspection Picture 2 5 Make2. sure that the unit is always well ventilated and never exposed to direct sunlight 6 Do not use sprays to clean the unit as they have a detrimental effect on the unit and could ignite suddenly 7 The machine use single power switch please cut off the power before fix 8 Please do not put the vessel of flower or container above the machine In case the leak out water then cause the leakage current off the machine Channeli Channel 2 o udio input and output connections Control elements BALANCED INPUT CONNECTIONS The XLR input connectors are electronically balanced and wired according to the IEC 268 standard pin 2 hot XLR input connectors should be wiredas follows Pin 1 Ground shield Pin 2 Hot Audio inputs 2 channel models Pin 3 Cold When linking the same source signal to several input channels be aware that there isa limit to the number of channels an output source can drive A typical output source e g a DSP crossover unit can drive up to two amplifier channels before external line drivers might be required to buffer the signal Unbalanced Input connections To connect an input to an unbalanced source it is possible to connect pins 1 and 3 in the XLR plug at the amplifier end of the cable However a better method is to connect pin 3 to the shield at the source end of the cable as this usually results in better hum and noise r
3. User s Manual FP14000 Professional Power Amplifier Professional Power Amplifier Specifications Contents Model FP14000 rr 2x2400W Importantnote 2x4350W 265000 87000 Control elements 13000w Rear panel features introduction TAO Mae power a 01 Audio input and output connections ira hoe Fat an 11008 7 ml Du Cone Speakon Connectors NEUTRIK Power Requrenent 0024 8080 Stereo Mode Bridge Mode hene ABIT Professional Power Amplifier Specifications Mesrine 13K9 Importantnote Stereo Mode Before setting the mode please turn off the amplifier and slide the manufactured to assure your personal safety Improper use can result in potential electrical Shock or fire hazards In order not to defeat the safeguards observe the following precautions for its installation use and servicing mode select switch to below Picture 1 In this mode Channel 1 Em an Channel 2 operate independently just traditional stereo ARNING NOTICE amplifier The signal input into channel 1 can be output from mad 5 SAFEGUARDS channel 1 only similarly the signal input into channel 2 can FA H 6 output from channel 2 only The many channels one by one in Electrical energy can perform many useful functions This unit has been engineered and order type pushes HE 4 Picture 1
4. a cause for concern If this LED is lit permanently volume should be reduced to avoid overload damages to the connected loudspeaker systems 7 VHF VHF Very High Frequency protection active output muted Yellow constant 8 CPL LED CPL Orange constant with output muted Low impedance short circuit detection fault 9 POWER Switch LED Turn the unit power on lights up or off lights out 10 BRIDGE LED The light up mean it is bridge else no bridge e Rear panel features introduction features introduction XLR connectors for inputs and loop thru Rear view of 2 channel model fitted with Speakon connectors Two channel model shown Two channel versions have VCL and Bridge Mode switches for channels and 2 only All models have different VCL values Functions are otherwise gt identical 6 2 2 The DIP switch features pa pgp aves votracecuriarer The following features may be adjusted using the DIP et GER Swen switches on the rear panel of the amplifier Gain xam i iwah m cB Globally set for all channels from 23 dB to 44dB in 3 on gon dB steps Bridge 1 2 Switches the channel pairs into bridge mode operation An automatic 6 dB gain compensation is applied VCL Voltage Clip Limiter adjustment is provided for eight discrete Vet vorracecur unrr
5. ejection Balanced input connections are recommended whenever possible Speakon Output connections Refer to the instructions in this section if your amplifier is equipped with the Speakon output connectors a Speakon outputs 2 channel models F ront panel The front panel LED area includes the following indicators per channel 0 o 1 LEVEL CONTROL Calibrated detente potentiometers to alter the total gain of the power amplifier Ln order to avoid distortions in mixing consoles upstream these controls should normally be positioned between 0 and 10 The calibrated markings show the additional attenuation directly 2 PROLED Au protection under mute position 3 Clip limit indicator This indicator signals if the amplifier output is clipping limiting It has two different indication states If the clip limiter is engaged it has a short time constant and it illuminates briefly If the clip limiter is not engaged it has an increased time constant and it illuminates for a longer period 4 516 HI IMP LED en SIG Indicates output signal levels in normal operating range Hi Imp High impedance open load detected Orange 5 Limit power LED When this LED lights up the Limit power function is working 6 TEMP This LED lights up if the limiter has been activated and the power amplifier is being operated at the clip level If the LED flashes briefly this is not
6. en levels for each channel for each channel Select the setting most appropriate for connected speakers 195V 100V qv ov qe uv sv EF Noel Mode Select mode to either Hard or Soft operation For iv channels driving sub woofers and low frequency drivers it is mov recommended to use the Hard setting for optimal operation For ef mid and high frequency drivers always select Soft EM iv v Output connectors Input or output connectors Audio inputs or output 2 channel models Two channel amplifiers Additional connectors are provided for Channel 1
Download Pdf Manuals
Related Search