Operating Instructions Washing Machine
Contents
1. NOTE Make sure the detergent compartment is completely dry before you add detergent otherwise there is a risk that the detergent will clump before the machine starts Close the washer door and press the Start Stop button a Start Stop Time remaining When the programme starts an estimated programme time in hours and minutes is displayed The remaining time is updated three times during the programme based on the actual load and the incoming water temperature The first update takes place after about 15 minutes The remaining time is last updated just before the final rinse To add or remove washing after the program starts If you want to add or remove items after the programme has started you can stop the programme by pressing and holding the Door opening button key symbol for three seconds The programme time flashes on the display When you restart the machine add any extra detergent needed and close the washer door The machine continues automatically from the point where the programme was interrupted Stopping or changing a programme You can stop a programme by pressing the Start Stop button for three seconds To restart the machine select a new programme add any extra detergent needed and press the Start Stop button NOTE Do not open the detergent compartment while the machine is running Once the program has finished Once the programme has finished End appears in the di2. Drain 1 7 m polypropylene hose 3 4 BSP connection Transport protection Remove the three transport bolts and the plastic plugs for locking the machine for transport before using the machine N r N TES AUEN r ji NOTE If the machine is to be transported the bolts and plastic plugs for locking the machine during transport must be installed to prevent damage to the machine through shaking If the transport bolts or plastic plugs have been lost you can 1 Loosen and remove the bolts as illustrated below order new ones from your retailer Article number 80 882 77 80 901 05 2 Toremove the plastic plugs that held the bolts squeeze together and pull out Remove the plastic covers from the plugs Push the plastic covers into the three holes that contained the plugs Save the plastic plugs in case the machine is moved in the future Designation Screw Plastic plug transport lock Order three of each item 25 26 Installation Positioning the washing machine The washing machine can be installed as a built in or freestanding unit Position the machine so that the electrical plug is easily accessible A Built in The washing machine can be installed under a counter top with a working height of 850 900 mm Leave a5 mm space around the entire machine including between the rear edge of the top cov
3. 2 Turn on the main power switch Open the washer door and load the washing If the washer door is closed press the Door opening button key symbol The door opens once all water has drained from the machine Load the washing The wash programme chart shows how much washing can be washed with each programme Add detergent and fabric softener as required The detergent packaging will have recommendations for how much detergent you should use The machine holds 8 kg of washing If you only have a small amount of laundry in the machine you can reduce the amount of detergent used Powder detergent Pour the powder into the compartment for the main wash and pre wash as well if desired Liquid detergent When using liquid detergent follow the detergent manufacturers recommendations We recommend always using a wash ball with very thick liquid detergent Wash ball or net If you use a wash ball or net place it directly in the drum and select a programme without pre wash NOTE Detergent overdosing does not give better washing results it merely causes a greater impact on the environment Try using less detergent and increase only if you are not satisfied with the results Fabric softener Pour the fabric softener into the compartment with the symbol Follow the recommendations on the fabric softener packaging NOTE Do not fill above the compartment s maximum fill level Otherwise fabric softener will run in
4. the Door opening button key symbol and the door will open 3 Load the washing and close the washer door 3 Detergent compartment 1 Pour detergent into the main wash compartment and pre wash compartment as well if required Pour Art No 8093734 Rev 01 We reserve the right to make changes 3 fabric softener into the compartment on the right with the symbol 2 If you use liquid detergent follow the detergent manufacturer s recommendations Select the programme 1 Select a programme by turning the programme selector 2 Select any options and settings 3 Press the Start Stop button Program finished 1 The text End on the display indicates that the wash programme has finished 2 The washer door opens automatically once the programme has finished 3 Remove the load 4 Turn off the main power switch If you have small children or pets at home close the washer door once you have removed the laundry CE
5. the nipple e Remove burrs from the hole See the illustration SS NN At least 18 mm Electrical installation Connect the machine by plugging it into an earthed wall socket The electrical wall socket must be placed outside of the installation area to be easily accessible Connection on delivery The machine is supplied as 1 Phase 220 230V 50 60Hz heat output 2000W and has a 10A plug Any residual current devices must be type A NOTE Repairs and maintenance relating to safety or performance must be carried out by a qualified professional 27 28 Service Before contacting the service 07000 am division Before you contact the service division make sure that you know the model designation type designation and serial number The model designation can be found on the panel The type designation and serial number can be found on the type plate on the inside of the washer door Type designation a TYPE WM70 1 C 63 p P 230 V 1a c 2200 W o LAMA 200 450 w mo o1tmpa RTnO9203162 012512345678 Serial number 12 digits Model designation Type plate Your notes 29 Your notes Your notes 31 32 Quick guide Washing 1 Empty pockets and refasten zips 2 Read the item s laundry label 3 Sorting laundry NOTE Place underwired bras in a laundry net Load the laundry 1 Press the main power switch 2 If the washer door is closed press
6. too early which impairs the washing effect 11 12 Washing Select the programme You select a programme by turning the programme selector An LED lights up beside the selected programme and the estimated programme time is shown on the display Use the option buttons to select any options Quick Easy Care Colour White Synthetics Normal Wool hand wash Heavy Rinse Auto Spin amp Drain 1 Auto This program automatically adjusts the length of the main wash and the number of rinses to the amount of laundry loaded in the machine 2 Heavy Programme for heavily soiled laundry with dirt that needs to be fully dissolved before the main wash A pre wash is used to do this You can select the temperature freely so follow the washing instructions for each garment The highest temperature 95 C is suitable for very heavily soiled laundry The spin speed can be selected freely The machine adapts the programme time and water consumption to the load size 3 Normal Program for normally to heavily soiled laundry whites and colors You can select the temperature freely so follow the washing instructions for each garment 60 C is a good temperature for heavily soiled cotton garments as well as for garments worn next to the skin Select 40 C if the laundry is less soiled The spin speed can be selected freely The machine adapts the program time and water consumption to the load size 4 Colour White A st
7. C full and half load The actual water consumption will depend on how the machine is used On a scale from G least efficient to A most efficient Normal 60 C and 40 C are the standard wash programmes used to compile the information for energy labelling These programmes are intended for washing normally soiled cotton textiles and are the most effective programmes in terms of combined energy and water consumption 23 Technical information Information for test institute Program Max load Temp C Auto 1 2 Normal 1 1 40 60 Easy Care 1 2 40 1 Short programme for test institutes max 1 2 load 2 Test programme for cold water connection in accordance with EN 60456 For large volumes of detergent we recommend removing the insert and adding detergent directly to the detergent compartment 3 40 C programme for test institutes The 40 C option must be selected Energy labelling European test standard EN 60456 Washing program Normal 8 kg cotton Connection Cold water 15 C Test method for noise measurement IEC 60704 2 4 Technical data Height 850 mm Width 595mm Depth 585 mm Weight 73 kg Cylinder volume 601 Rated power See type plate Heater output See type plate Water pressure 0 1 1 MPa 1 10 kp cm 10 100 N cm Wash drum and liquid compartment material Stainless steel Outer casing material Powder coated and hot galvanized sheet steel or stainless steel Water connection 1 5 m pex pipe
8. O if extra rinses 5 rinses is activated or R F if itis not activated 3 rinses Turn the programme selector to change the setting Press the Door opening button to save the setting Care and cleaning Cleaning the trap and the drainage pump The washing machine has a trap where smaller objects such as coins and hairpins can collect To clean the trap and the drainage pump do as follows 1 Make sure the machine is empty of water and switched off at the mains ee qe 2 Open the door 3 Unhook the drainage hose from the connector inside the door and drain the water into a suitable container such as a shallow bowl 4 Turn the cover anti clockwise to open the pump Remove the cover 5 Remove any items and so forth from the pump housing and the cover Also check that the pump blades right at the back rotate 6 Screw on the cover replace the drainage hose on the hatch pin and close the hatch Cleaning the detergent compartment NOTE Do not wash the detergent compartment or the insert in a dishwasher Open the detergent compartment and remove the insert Rinse the insert and scrub it clean with a washing up brush Wipe up any detergent left inside the detergent compartment Replace the insert in the detergent compartment Detergent compartment Cleaning the outside of the machine Clean the outside of the machine and the program panel with a mild cleaner Do not use an
9. Operating Instructions Washing Machine ISE W256W Dear ISE customer Welcome to the family of ISE customers We hope that you will have many years of use from your new machine The machine has many features To make the most of its functions we recommend that you read the operating instructions before using the machine The operating instructions include information on how you can help protect the environment Contents Before using your machine for the first time Transport protection Packing material Washer door Checking water hardness Safety instructions General Installation Overflow guard function Transport Winter storage Recycling Child safety Keep an eye on children Description of the washing machine Detergent compartment Advice and tips before washing Sorting your laundry Clothing Laundry labels Laundry label symbols Coloured cotton Unbleached linen Wool Rayon fibres and synthetic fibres Reducing allergic reactions Save time and energy High water level Economy and efficiency Detergents Dyeing fabrics Ooan n ena an a rtskt ARAARA O O O O O O O O CO O O O ON N Washing Sort your laundry Turn on the main power switch Open the washer door and load the washing Add detergent and fabric softener as required Select the programme Select options Close the washer door and press the Start Stop button Once the program has finished Settings You can change the following s
10. andard programme for lightly to moderately soiled laundry The temperature can be selected freely so follow the washing instructions for each garment Garments worn next to the skin ought to be washed at 60 C Very lightly soiled laundry often comes clean already at 40 C The spin speed can be selected freely The machine adapts the programme time and water consumption to the load size 5 Quick Fast program for laundry that just needs freshening up The program can be run at any temperature so follow the washing instructions for each garment The lower the selected temperature the shorter the program time Garments worn next to the skin ought to be washed at 60 C The spin speed can be selected freely 6 Easy Care Programme for synthetic mixed fibre and easy care cotton The programme has a high water level and as such is also suitable for cushions quilted jackets and the like Read the washing instructions carefully and remember for example that fabric softener must not be used with the membranes found in some outer garments A washing temperature up to 60 C and a spin speed up to 1200 rpm can be selected 7 Synthetics Programme for delicate garments made of synthetic fibre mixed fibre rayon and easy care cotton The maximum temperature is 60 C but follow the washing instructions for each garment Many synthetics will come clean at 40 C Garments worn next to the skin ought to be washed at 60 C The ma
11. ble for their safety e Children must be watched to ensure they do not play with the machine e Inthe enclosed plastic bag you will find a tool for opening the washer door in emergencies Installation See the Installation chapter Overflow guard function If the machine s water level rises above the normal level the overflow guard function begins to pump water out and shuts off the water intake If the water level has not dropped within 60 seconds the program is terminated A Transport Winter storage If the machine is to be transported or stored in unheated premises where the temperature can fall below freezing do as follows e Empty the filter and the drainage pump See the Care and cleaning chapter e Shut off the water to the washing machine loosen the supply hose to the intake valve and let the water run out from the valve and hose e After emptying the pump a small amount of water may remain in the machine This does not affect quality or damage the machine Recycling This machine is manufactured and labelled for recycling In order to prevent injuries the machine must be made unusable once the decision has been taken to dispose of it Contact your local authority for information about where and how your machine can be recycled correctly Child safety Keep an eye on children Always close the washer door and start the programme immediately after you have added detergent Do not allow small childre
12. ct No spin To find out how to choose this setting see the Washing chapter However most garments can withstand a short spin Choose a short spin by selecting a spin speed of 800 rpm or less Rayon fibres and synthetic fibres Materials made of rayon fibres such as viscose and some synthetic fibres are very delicate and require much space so as not to crease Only half fill the drum when washing and choose a spin speed of 800 rpm or lower NOTE Viscose and acetates are fragile when wet Reducing allergic reactions The washing machine has a Super Rinse option Use this for people with sensitive skin such as those with allergies and small children Save time and energy Use the Colour White programme to save time and energy This programme has a shorter main wash than Normal but is often sufficient for lightly soiled washing High water level If you want more water for the main wash and rinses you can use the High water level option High water level is used automatically in the Wool Hand programme Economy and efficiency You can save a lot of energy by not using higher temperature programs than necessary e Select Quick if you just need to freshen up shirts or exercise clothes for example This will save both water and energy e If you select a fast spin speed this reduces energy consumption when drying in a tumble dryer or drying cabinet e Always wash with a full load when using the Heavy Colour Whit
13. door while a programme is running see Close the door and press the Start Stop button in the Washing chapter Checking water hardness The quantity of detergent needed depends amongst other things on how hard the water is See the detergent pack for details Phone your local water company to check the water hardness in your area NOTE Each machine is tested before leaving the factory A small amount of water may remain in the drain pump though this does not affect quality or damage the machine See Quick guide on the last page Safety instructions General e Read the operating instructions and keep them in a safe place e Installation of water and electricity if required should be carried out by a qualified professional e The machine should only be used for washing items as described in these instructions It is not intended for dry cleaning e Use only detergent intended for machine washing e Remove any transport protection devices before using the machine See the Transport protection chapter e Repairs and maintenance relating to safety or performance must be carried out by a qualified professional e Damaged mains cables must only be replaced by a qualified electrician e The machine is not designed to be used by persons even children that are physically or mentally handicapped or lack experience and knowledge Such persons must receive instruction in how to use the machine from the person responsi
14. e and Normal programmes e Avoid pre washing Modern machines and detergents clean effectively without pre washing Pre washing is only necessary for heavily soiled washing Detergents Eco labelled detergents are less harmful to the environment Detergent overdosing does not give better washing results it merely causes a greater impact on the environment Try to use less detergent and increase only if you are not satisfied with the results Dyeing fabrics If you want to dye fabrics in the machine select the Colour White programme with the Super Rinse option Select temperature according to the dye manufacturer s recommendations Choose a low spin speed if the fabric to be dyed is a blended material such as polyester cotton NOTE Add the dye directly to the washing drum not to the detergent compartment After dyeing you should run the machine empty using the same program Use the normal amount of detergent 10 Advice and tips before washing NOTE Due to environmental concerns we discourage the use of strong chemicals When using agents for bleaching or stain removal there is a risk of rust corrosion and discolouration of the machine Washing Sort your laundry See the Advice and tips before washing chapter Place underwired bras in a laundry net Empty pockets Coins nails and the like can cause damage to the machine and fabrics See the Advice and Tips section before washing
15. e not selected Delayed Start To cancel Delayed Start press the Start Stop button for three seconds 21 22 Troubleshooting Error messages If an error occurs during the programme a message is shown on the display To exit the message after taking measures turn the machine off and then back on The error messages that may be shown in the display are F10 Overfilling 1 Shut off the water tap 2 See Drainage error F11 Drainage error Check e that no objects are stuck in the drainage hose outlet e that the drainage pump is not blocked by foreign objects Clean the pump See the Care and cleaning chapter e that there are no kinks in the drainage hose After taking measures run the Drain programme or press the Door opening button key symbol to empty the machine If this does not resolve the problem call the service division F12 Water inlet fault Check e that the tap on the water pipe is open e that the filter in the machine s water intake is not blocked Action 1 Shut off the water tap 2 Unscrew the hose 3 Clean the filter in the intake valve on the machine 4 Screw the hose back on Turn on the tap Run the program again to check if the fault is fixed If this does not resolve the problem call the service division O o1 N Imbalance The machine stops the spin cycle if there is too much imbalance The washing machine restarts the spin cycle and hopeful
16. elect temperatures between 20 C and 95 C For Wool hand wash you cannot choose a temperature higher than 40 C For Synthetics or Easy Care the maximum temperature is 60 C Spin e Select the spin speed by pressing the button until the LED by the desired speed lights e You can select speeds between 400 and 1600 rpm No spin or No drain The maximum spin speed varies according to the programme selected so check the LEDs around the button A means that the programme does not include a spin cycle and ends by draining Y No drain means that the programme does not include a spin cycle and ends with the water from the final rinse still in the machine The washing will remain covered by the water from the final rinse stopping it from getting creased If you have selected No drain you must select the Spin amp Drain programme and the A symbol no spin once the programme has ended to drain the water from the machine before you open the washer door WwW Super wash Super wash can be selected to better dissolve difficult stains and heavy soiling on clothing This option adds a cold pre wash and the wash time in cold water is extended by approximately six minutes The main wash time is also extended e Select Super wash by pressing the button by the symbol e An LED next to the button lights when this option is activated Co High water level High water level means that additional water is used during the mai
17. er and the wall behind it B Freestanding The washing machine can be positioned beside or under a tumble dryer Adjusting the feet Keep the noise that the machine produces to a minimum by adjusting the feet so that the machine is steady and balanced on the floor Tighten the lock nuts Locking nut Connection to water supply Water connection should be carried out by an appropriately qualified person Connect the machine using the accompanying supply hose Water pressure should be 0 1 1MPa approx 1 10kp cm 10 100N cm There should be a stopcock on the water pipe If the pipes are newly installed it may be wise to flush them through so that any dirt is washed away Otherwise dirt can clog the filter in the machine s water intake and cut off the water supply Use only the supply hose supplied with the machine Do not re use old hoses or other loose supply hoses Drainage connection The machine is supplied with a drainage hose attached which must be connected to a drain See the examples below The height must be 600 900 mm above floor level The lower position 600 mm is always preferable Ensure that the drainage hose has no kinks 600 900 mm gt Installation The machine can also be connected to the drain via a spigot connection In this case the hose should also be 600 900 mm above the floor The internal diameter of the hole should be at least 18 mm e Cut
18. ettings Door opening Extra rinses Care and cleaning Cleaning the trap and the drainage pump Cleaning the detergent compartment Cleaning the outside of the machine Cleaning the inside of the machine to avoid unpleasant smells Rinse holes under the agitator If you have hard water Troubleshooting The washer door will not open The machine will not start Error messages Technical information Information on energy labelling Information for test institute Technical data Transport protection 11 11 11 11 11 12 15 16 16 18 18 18 18 19 19 19 19 19 20 20 21 21 21 22 23 23 24 24 25 Contents Installation Positioning the washing machine Adjusting the feet Connection to water supply Drainage connection Electrical installation Service Before contacting the service division Quick guide 26 26 26 26 26 27 28 28 32 Before using your machine for the first time Transport protection Remove any transport protection devices before installing the machine See the Transport protection chapter Packing material Please sort waste materials in accordance with local guidelines Washer door e The washer door cannot be opened until the machine is connected to the electricity supply e To open the door manually see The washer door will not open in the Troubleshooting chapter e The machine cannot be started when the door is open e To open the washer
19. le presents a few examples of the energy water and time consumption of a few different programme settings Consumption can vary depending on water pressure water hardness water supply temperature room temperature load weight and content variations 40 C programme for test institutes The 40 C option must be selected in the power supply and selected options In the examples provided here the rinse setting is set to Normal and no options are selected If you use large amounts of detergent such as non compact powder and find that the amount you want to use does not fit in the compartment you can remove the insert and dose directly in the compartment We recommend that all test institutes remove the insert for large volumes of detergent Washing 40 30 20 95 400 1600 6 QA 1200 50 BE Select options You can select options to adjust the wash programme to suit your own specific requirements The available options depend on the selected programme If the option is available for the selected programme the symbols lights up when you press the button The machine will remember the options you select for each programme with one exception Delayed Start You can still change the selected options the next time you select the programme in question R Temperature e Select the temperature by pressing the button until the LED by the desired temperature lights e You can s
20. ly the washing is better distributed in the drum This procedure can be repeated up to 10 times If the machine still fails to find a good balance the programme jumps to the next step The error message requires no action Technical information Information on energy labelling Information sheet in compliance with Commission Delegated Regulation EU No 1061 2010 ISE Model designation W256W Max washing capacity 8 kg Energy efficiency class A Annual energy consumption AE 194 kWh per year Energy consumption Normal 60 C with full load E so 1 10 kWh Normal 60 C with half load E 9 _ 0 82 kWh Normal 40 C with half load E 49 _ 0 52 kWh Power consumption Off mode P 0 40 W Left on mode P 1 20 W Annual water consumption AW 12100 litres per year Spin drying efficiency class A Maximum spin speed 1600 rpm Remaining moisture content 44 Washing program Normal Programme time Normal 60 C with full load T so 200 minutes Normal 60 C with half load T 604 155 minutes Normal 40 C with half load T 404 145 minutes Noise emissions Wash phase 48 dB A re 1 pW Spin phase 73 dB A re 1 pW Based on 220 standard cleaning cycles for Normal 60 C and 40 C full and half load and consumption in accordance with the low power modes The actual energy consumption will depend on how the machine is used Based on 220 standard cleaning cycles for Normal 60 C and 40
21. n to use or play with the washing machine Store detergent and fabric softener out of the reach of children Description of the washing machine Main power switch Detergent compartment Programme panel Serial number plate on inside of washer door Drainage pump cover Drainage pump behind cover Washer door NOOR WD Detergent compartment 1 Pre wash O A 2 Main wash Da 3 Main wash liquid detergent i 4 Fabric softener ae Advice and tips before washing Here are some tips that may help you before washing Sorting your laundry Sort items according to e how soiled they are e colour e material Clothing 1 Doup zips and close Velcro straps so that they don t harm fabrics 2 New coloured items may contain excess dye and should therefore be washed separately the first few times Turn delicate items inside out This reduces the risk of burling and fading Empty pockets and wash them inside out if possible oo D Laundry label symbols Laundry labels Look at the item s laundry label The table below shows suitable wash programmes for different materials and wash loads Using modern washing machines and detergents for example compact detergents you can usually wash at lower temperatures Itis a good idea to use trial and error to find out what produces the best results Examples of washing instructions and recommended programmes Alway
22. n wash and rinse cycles This option can be used with all programmes except Wool hand wash Rinse and Spin amp Drain e Select High water level by pressing the button by the symbol e An LED next to the button lights when this option is activated NOTE The machine takes in the additional water for the high water level about 15 minutes after the main wash has started 15 16 Washing Super rinse Use the Super Rinse option if you want to increase the number of rinses The maximum number of rinses is seven and the number of rinses varies depending on the selected programme Recommended for persons with extremely sensitive skin and or in areas with very soft water This option cannot be selected with Rinse or Spin amp Drain e Select Super Rinse by pressing the button under the symbol e An LED next to the button lights when this option is activated Delayed start When you select Delayed Start the machine will start 1 24 hours after you press the Start Stop button e Press the button by the symbol to activate Delayed Start e By pressing the button again you can delay the start in whole hours up to a maximum of 24 hours e Press Start Stop and the machine counts down 1 hour ata time and starts after the selected delay If you change your mind and want to cancel Delayed Start you must press and hold Start Stop for three seconds NOTE Remember to press the Start Stop button to start the programme
23. pproximately 20 gram of citric acid into the wash drum and run any 95 C programme Repeat if necessary Troubleshooting The washer door will not open 1 Check that the main power switch is on 2 Is there power Check your home s fuses circuit breakers The washer door cannot be opened with the door opening button with the key symbol if power is off If nothing else works the washer door can be opened as follows WARNING JN The door may only be opened manually if the electric power is cut and the machine has been drained of water A Select the Spin amp Drain programme and the option with the O symbol no spin to drain the water from the machine If this does not work the machine must be drained manually See Cleaning the trap and the drainage pump in the Care and cleaning chapter B Ensure thatthe main power switch is turned off and thatthe plug has been removed from the wall socket C Take the emergency door opening tool and place it in the gap on the right side of the washer door lock This tool is found in the enclosed plastic bag D Push the tool upwards to open the washer door If in the future the washer door does not open when the wash programme has finished call the service division The machine will not start 1 Is the washer door properly closed Push it firmly 2 Is there power Check the fuses and residual current devices circuit breakers in the building 3 Check that you hav
24. s follow the washing instructions for each garment Laundry labels Material Program Load Cotton linen white and light coloured items Colour White 60 C to 95 C 1 1 drum Cotton linen cotton polyester Light and Quick 60 C 1 2 drum y dark coloured garments Acrylic viscose modal acetate polyester Easy Care 40 C 1 2 drum 40 polyamide and elastane Light and dark col oured garments ta Wool silk and other very delicate garments Wool hand wash 30 C to 40 C 1 3 drum or Coloured cotton Coloured cotton items with the washing instruction 60 C should be washed at 60 C for the first time in order to remove any excess dye If you do not do so there is a risk that the colour will run Use detergent without bleach in order to preserve the colour of the fabric Unbleached linen Unbleached linen fabrics should be washed at 60 C using detergent containing no bleach or optical whiteners Heavily soiled linen can occasionally be washed at higher temperatures but not too often because the heat can destroy the linen s shine and strength Advice and tips before washing Wool These fabrics are labelled either machine wash or hand wash The Wool hand wash programme is at least as gentle as washing by hand Woolis especially sensitive to processes such as washing If you do not wish to spin dry you can squeeze out the water using terry towels In this case sele
25. splay Washing The washer door opens automatically once the programme has finished If you want to deactivate the automatic door opening function see the Selecting settings section e Remove the load e Turn off the main power switch this will save energy If you have small children or pets at home close the washer door once you have removed the laundry Backlighting Two minutes after the wash programme finishes the display backlighting enters energy saving mode 17 18 Settings You can change the following settings Automatic door opening Extra rinses Door opening If you choose Automatic door opening the Washer door will open once the programme has finished 1 2 3 4 5 Turn off the machine using the main power switch Press and hold the Super rinse button and then switch on the main power switch AdO is shown on the display if Automatic door opening is activated or AdF if the option has not been activated Press the Super Rinse button to change the setting Press the Door opening button to save the setting Extra rinses Upon delivery your washing machine is set to use five rinses in the Normal and Colour White programmes If you want to reduce the number of rinses to three for these programmes do as follows ahWON Turn off the machine using the main power switch Press and hold the Delayed start button and then switch on the main power switch The display shows R
26. ximum spin speed is 800 rpm Washing 8 Wool hand wash A gentle laundry programme for wool silk and garments that should be washed by hand The highest temperature is 30 C This programme has ashort spin The maximum spin speed is 800 rpm 9 Rinse This program performs one cold rinse cycle spin Suitable for laundry that just needs to be dampened and for cleaning cloths and mops 10 Spin amp Drain Used to just spin the wash If you only want to drain the machine of water select the A symbol no spin 13 14 Washing Programme chart Water consump Energy consump Programme time Pre Number of Spin Speed Max load tion tion approx hrs and Program wash Temp C Rinses rpm kg approx liter approx kWh min 1 Auto gt Hea XxX 95 5 1600 8 85 2 2 2 45 rege x 60 5 1600 8 75 1 1 2 40 60 3 1600 8 65 1 10 3 20 3 Normal J 40 3 1600 8 65 0 67 2 57 4 Colour White 60 3 1600 8 60 1 2 1 40 5 Quick 40 2 1600 4 0 25 0 4 0 45 6 Easy Care 40 2 1200 4 0 50 0 5 1 20 7 Synthetics 40 3 800 2 5 30 0 4 1 20 8 Wool hand wash 30 3 800 2 5 70 0 5 0 50 9 Rinse 1 1600 4 0 15 0 1 0 18 10 Spin amp Drain 1600 4 0 0 1 0 15 1 Test programme for cold water connection in accordance with EN 60456 For large volumes of detergent we recommend removing the insert and adding detergent directly to the detergent compartment 2 The above tab
27. y solvents as these can damage the machine NOTE Do not hose down the machine with water Cleaning the inside of the machine to avoid unpleasant smells Modern detergents often allow clothes to be washed at low temperatures This means that small deposits can build up in the machine These in turn may lead to unpleasant smells developing To avoid this we recommend running a 95 C wash programme once a month When you do this use a small quantity of detergent It is not necessary to put any washing in the machine 19 20 Care and cleaning Rinse holes under the agitator If you suspect that objects such as nails or paper clips may have fallen into the wash drum you should check the space under the agitator Such objects can rust and cause spots on clothing Nails and other sharp objects can cause holes in fabrics Do as follows 1 Insert a screwdriver or the like into the hole on the agitator as illustrated and carefully pry to the left 2 Use your other hand to grasp the agitator and pull it towards you 3 Lift the agitator 4 Remove any objects 5 Place the agitator in the mounting hole with the F mark towards you Ensure that all the agitator fasteners are in their holes in the drum Push it in until it catches If you have hard water If you live in an area with hard water high limescale content a greyish white coating may form on the wash drum To remove this coating pour a
Download Pdf Manuals
Related Search