Home

User's Manual - CNET Content Solutions

Contents

1. 1 DC IN 19V jack 2 DC output plug Product appearance depends on the model you purchased 3 Plug the power cord into a live wall outlet the DC IN Battery indicator should glow Opening the display The display panel can be opened to a wide range of angles for optimal viewing While holding down the palm rest with one hand so that the main body of the computer is not raised slowly lift the display panel this will allow the angle of the display panel to be adjusted to provide optimum clarity User s Manual 2 4 Figure 2 4 Opening the display panel ws 1 Display panel Product appearance depends on the model you purchased T User s Manual Use reasonable care when opening and closing the display panel Opening it vigorously or slamming it shut could damage the computer Do not put your fingers in the gap between the LCD panel and battery pack when closing your LCD otherwise your fingers might get hurt Be careful not to open the display panel too far as this could put stress on the display panel s hinges and cause damage Do not press or push on the display panel Do not lift the computer by the display panel Do not close the display panel with pens or any other objects left in between the display panel and the keyboard When opening or closing the display panel place one hand on the palm rest to hold the computer in place and use the other hand to slowly open or close the display panel Do not use excess
2. 4 The names OpenSSL Toolkit and OpenSSL Project must not be used to endorse or promote products derived from this software without prior written permission For written permission please contact openssl core openssl org 5 Products derived from this software may not be called OpenSSL nor may OpenSSL appear in their names without prior written permission of the OpenSSL Project User s Manual 1 8 User s Manual 6 Redistributions of any form whatsoever must retain the following acknowledgment This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http Awww openssl org THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT AS IS AND ANY EXPRESSED OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE This product includes cryptographic software written by Eric Young eay crypt
3. Chapter 7 Appendix Specifications This section summarizes the computer s technical specifications Physical Dimensions Physical Dimensions shown below do not include parts that extend beyond the main body The physical dimensions may vary depending on the model you purchased Size E Approximately 380 w x 259 9 d x 23 5 23 5 h millimeters E Approximately 380 w x 259 9 d x 24 5 24 5 h millimeters m Approximately 380 w x 261 9 d x 19 9 19 9 h millimeters H Approximately 380 w x 261 9 d x 19 9 21 9 h millimeters not including parts that extend beyond the main body Environmental Requirements Conditions Ambient temperature Relative humidity Operating 5 C 41 F to 35 C 20 to 80 95 F noncondensing Non operating 20 C 4 F to 60 C 10 to 90 140 F noncondensing Wet bulb temperature 29 C maximum Conditions Altitude from sea level Operating 60 to 3 000 meters Non operating 60 to 10 000 meters maximum User s Manual 7 1 Power Requirements AC adaptor 100 240V AC 50 or 60 Hz cycles per second Computer 19V DC External RGB monitor port pin assignment o 6 Pin Signal Name Description 1 0 1 CRV Red Video Signal O 2 CGV Green Video Signal O 3 CBV Blue Video Signal O 4 Reserved Reserved 5 GND Ground 6 GND Ground 7 GND Ground 8 GND Ground 9 5V Power Supply 10 GND Ground 11 Reserved Reserved 12 SDA Data Signal VO 13 HSYNC Horizontal Sync Signal O
4. Media care Card care 4 25 Memory card care 4 26 memory media card inserting 4 26 removing 4 27 Memory media slot 4 24 Moving the computer 1 17 MultiMediaCard removing 4 27 Password power on 5 5 Starting the computer by password 5 10 Supervisor 5 9 user 5 8 Pointing Device Touch Pad 3 9 Power conditions 3 13 Hibernation Mode 2 9 panel on off 5 5 Shut Down mode 2 6 Sleep Mode 2 7 turning off 2 6 turning on 2 6 Problems AC power 6 4 Analyzing the problem 6 2 Battery 6 5 Dual Pointing device 6 8 External monitor 6 12 Hardware and system checklist 6 4 HDD 6 7 Internal display panel 6 6 Keyboard 6 6 Memory Media Card 6 8 Overheating power down 6 4 Power 6 4 Real Time Clock 6 6 Sound system 6 12 TOSHIBA support 6 14 Touch Pad 6 8 USB device 6 10 USB mouse 6 9 Recovery hard disk drive 5 15 Recovery Media 5 14 Restarting the computer 2 7 SD SDHC SDXC Card formatting 4 25 note 4 25 Security lock 4 30 Sleep Mode setting 2 7 Index 2 System automatic 5 5 Sound system problems 6 12 TOSHIBA Disc Creator 4 12 TOSHIBA HDD SSD Alert Utility 5 3 TOSHIBA PC Diagnostic Tool 5 1 Touch Screen USB device problems 6 10 Video mode 4 33 Video RAM 3 11 W Web Camera 3 8 Wireless communication 7 5 User s Manual Index 3
5. m Encryption prevents eavesdropping and maintains link privacy Worldwide operation The Bluetooth radio transmitter and receiver operate in the 2 4GHz band which is license free and compatible with radio systems in most countries in the world Radio links You can easily establish links between two or more devices with these links being maintained even if the devices are not within a line of sight of each other Bluetooth Stack for Windows by TOSHIBA Please note that this software is specifically designed for the following operating systems E Windows 7 Information regarding the use of this software with these operating systems is listed below with further details being contained with the electronic help files supplied with the software ie This Bluetooth Stack is based on the Bluetooth specification depending on T the model you purchased However TOSHIBA cannot confirm the compatibility between any computing products and or other electronic devices that use Bluetooth other than TOSHIBA notebook computers Release Notes related to the Bluetooth Stack for Windows by TOSHIBA 1 Fax application software Please be aware that there is some fax application software that you cannot use on this Bluetooth Stack 2 Multi user considerations The use of Bluetooth is not supported in a multi user environment This means that when you use Bluetooth other users that are logged into the same computer will not be able to use thi
6. 7 Security lock slot port 4 HDMI out port Provided with some models Product appearance depends on the model you purchased Headphone A 3 5 mm mini headphone microphone combo Microphone combo jack enables connection of a monaural jack microphone or a stereo headphone Universal Serial Bus One Universal Serial Bus port which complies to USB 3 0 port the USB 3 0 standard is provided on the right side of the computer The USB 3 0 port is compliant with USB 3 0 standard and backward compatible with USB 2 0 devices The port with the icon 4 has Sleep and Charge function USB 3 0 port s may work as USB 2 0 port s when operating in USB Legacy Emulation mode egi Universal Serial Bus One Universal Serial Bus port which complies to USB 2 0 or 3 0 port the USB 2 0 or 3 0 standard is provided on the right side of the computer The USB port type may vary depending on the model you purchased The port with blue color is USB 3 0 port Hom HDMI out port HDMI out port can connect with Type A connector HDMI cable o External RGB monitor This port provides 15 pin analog RGB port port Please refer to the External RGB monitor port pin assignment section for information on external RGB monitor port pin assignment This port allows you to connect an external RGB monitor to the computer Cooling vents The cooling vents help the processor to avoid overheating cc Security lock slot A security cable can be attached to th
7. Problem The Touch Pad does not work Procedure Check the Device Select settings Click Start gt Control Panel gt Hardware and Sound gt Mouse Problem On screen pointer does not respond to pointing device operation Double tapping Touch Pad does not work The on screen pointer moves too fast or too slow The reaction of Touch Pad is either too sensitive or not sensitive enough USB mouse Problem On screen pointer does not respond to mouse operation Procedure In this instance the system might be busy Try moving the mouse again after waiting a short while In this instance you should initially try changing the double click speed setting within the Mouse Control utility 1 To access this utility click Start gt Control Panel gt Hardware and Sound gt Mouse 2 Within the Mouse Properties window click the Buttons tab 3 Set the double click speed as required and click OK In this instance you should initially try changing the speed setting within the Mouse Control utility 1 To access this utility click Start gt Control Panel gt Hardware and Sound gt Mouse 2 Within the Mouse Properties window click the Pointer Options tab 3 Set the pointer speed as required and click OK Adjust the touch Sensitivity To access it click Start gt Control Panel gt Hardware and Sound gt Mouse If you are still unable to resolve the problem contact TOSHI
8. c a d qu ils ont la priorit pour les bandes 5 25 5 35GHz et 5 65 5 85GHz et que ces radars pourraient causer du brouillage et ou des dommages aux dispositifs LAN EL The term IC before the equipment certification number only signifies that the Industry Canada technical specifications were met USA Federal Communications Commission FCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation Refer to the FCC information section for the detailed information The radiated output power of the Wireless device is far below the FCC radio frequency exposure limits Nevertheless the Wireless device shall be used in such a manner that the potential for human contact during normal operation is minimized In the usual operating configuration the distance between the antenna and the user should not be less than 20cm Please refer to the computer user s manual for the details regarding antenna location User s Manual The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population consult Safety Code 6 obtainable from Health Canada s website www hc sc gc ca Taiwan Article 12 Without permission granted by the NC
9. is being accessed you may lose data or damage the disk m Never turn off the power while an application is running Doing so could cause loss of data m Never turn off the power disconnect an external storage device or remove storage media during data read write Doing so can cause data loss 3 Click Start and then select Shut down 4 Turn off any peripheral devices connected to your computer Do not turn the computer or peripheral devices back on immediately wait a short period to avoid any potential damage Restarting the computer Certain conditions require that you reset the computer for example if E You change certain computer settings If you need to restart the computer there are two ways this can be achieved B Click Start Point to the arrow jg beside the Shut down button and then select Restart m Press CTRL ALT and DEL simultaneously once to display the menu window and then select Restart by clicking the power icon in the lower right corner Sleep Mode User s Manual If you have to interrupt your work you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode In this mode data is maintained in the computer s main memory so that when you turn on the power again you can continue working right where you left off When you have to turn off your computer aboard an aircraft or in places where electronic devices are regulated or controlled
10. media onto which the recovery image can be copied including disc media and USB Flash Memory Please note that some of the disc media may not be compatible with the optical disc drive connected to your computer You should therefore verify the optical disc drive supports the blank media you have chosen before proceeding USB Flash Memory will be formatted and all the data in the USB Flash Memory will be lost when proceeding Turn on your computer and allow it to load the Windows operating system from the Hard Disk Drive as normal Insert the first blank disc into the optical disc drive tray or insert the USB Flash Memory into one available USB port Click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt Recovery Media Creator After Recovery Media Creator starts select the type of media and the title you wish to copy and then click the Create button Restoring the pre installed software from your created Recovery Media A User s Manual If the pre installed files are damaged you are able to use the Recovery Media you have created to restore the computer to the state it was in when you originally received it To perform this restoration follow the steps below When you reinstall the Windows operating system the hard disk will be reformatted and all data will be lost Load the Recovery Media into the Optical Disc Drive or insert the recovery USB Flash Memory into one available USB port Turn off the
11. Changes or remove the password default Registered Selects the password A dialogue box will appear to allow you to set the password To enter a user password 1 Select Registered to display the following prompt Enter Password Enter a password The character string you enter is displayed as a string of asterisk 2 Click OK The following message appears allowing you to verify the password Verify Password 3 If character strings match the password is registered Click OK If they do not match the following message appears You must repeat from step 1 Entry Error To delete a user password 1 Select Not Registered to display the following prompt Enter Password 2 Enter the currently registered password The character string you enter is displayed as a string of asterisks 3 Click OK If the character string you enter matches the registered password the password option is reset and the display changes to Not registered If they do not match the following message appears You must repeat from step 1 Incorrect Password Owner String This blank field is used to display a message when the password field is displayed on startup If a password is not registered the message will not be shown Supervisor Password User s Manual If you set a Supervisor Password some functions might be restricted when a user logs on with the User Password You can start the Supervisor Password utility by accessing the f
12. Display 2 00 Security lOCK ceeseeseeensereeeees Optional TOSHIBA Accessories Sound System and Video mode Utilities and Advanced Usage Utilities and Applications Special features cccesseeeeee Using the TOSHIBA Sleep Utility TOSHIBA Password utility TOSHIBA HWSetup ee TOSHIBA PC Health Monitor System Recovery ceeeeeesee eee Troubleshooting Problem solving process Hardware and system checklist TOSHIBA support ee Appendix Specifications cesses AC Power Cord and Connectors Information for Wireless Devices Legal Footnotes ccccssseeeeeees GOSS aby wise A ce eee Index User s Manual Chapter 1 TOSHIBA Legal Regulatory and Safety This chapter states the Legal regulatory and safety information applicable to TOSHIBA computers Copyright Disclaimer and Trademarks Copyright 2014 by TOSHIBA Corporation All rights reserved Under the copyright laws this manual cannot be reproduced in any form without the prior written permission of TOSHIBA No patent liability is assumed with respect to the use of the information contained herein First edition March 2014 Copyright authority for music movies computer programs databases and other intellectual property covered by copyright laws belongs to the author or to the copyright owner Copyrighted material can be reproduced only for personal use or
13. Pad or closing opening the display panel m Start a communication application Apply impact or vibration to the computer Install remove or connect external devices including such items as a memory media card USB device external monitor or an optical digital device m Use the audio video control button to reproduce music or voice Open the optical disc drive Do not use shut down log off Sleep Mode or Hibernation Mode functions while writing or rewriting Make sure that the write rewrite operation is completed before going into either Sleep Mode or Hibernation Mode You can remove an optical media on the optical disc drive after writing is completed If the media is of poor quality or is dirty or damaged writing or rewriting errors may occur Set the computer on a level surface and avoid places subject to vibration such as airplanes trains or cars In addition do not use the computer on an unstable surface such as a stand Keep mobile phones and other wireless communication devices away from the computer TOSHIBA Disc Creator Please be aware of the following limitations when you use the TOSHIBA Disc Creator User s Manual DVD Video cannot be created using TOSHIBA Disc Creator DVD Audio cannot be created using TOSHIBA Disc Creator You cannot use TOSHIBA Disc Creator s Audio CD function to record music to DVD R DVD R DL DVD RW DVD R DVD R DL or DVD RW media H Do not use the Disc Backup functi
14. access this utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Sleep Utility i TOSHIBA Service Station TOSHIBA PC Health Monitor This application allows your computer to automatically search for TOSHIBA software updates or other alerts from TOSHIBA that are specific to your computer system and its programs When enabled this application periodically transmits to our servers a limited amount of system information which will be treated in strict accordance with the rules and regulations as well as applicable data protection law To access this utility click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt Service Station The TOSHIBA PC Health Monitor application proactively monitors a number of system functions such as power consumption battery health and system cooling informing you of significant system conditions This application recognizes the system and individual component serial numbers and will track specific activities related to their usage To access this utility click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt PC Health Monitor For details on TOSHIBA PC Health Monitor see the help file You may not have all the software listed above depending on the model you purchased To access the setup files of the drivers utilities Click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt Appli
15. application proactively monitors a number of system functions such as power consumption battery health and the system cooling informing you of significant system conditions This application recognizes the system and individual component serial numbers and will track specific activities related to the computer and their usage The collected information includes device operation time and number of actuations or status changes i e number of power button and FN key combination uses AC adaptor battery LCD fan HDD SSD sound volume wireless communication functionalities and USB information date of initial system use and also computer and device usage i e power settings battery temperature and recharging CPU memory backlight illumination time and temperatures for various devices The stored data uses a very small portion of the total hard disk capacity approximately 10MB or less per year This information is used to identify and provide a notification of system conditions which may effect the performance of your TOSHIBA computer It may also be used to help diagnose problems should the computer require service by TOSHIBA or TOSHIBA s authorized service providers Additionally TOSHIBA may also use this information for quality assurance analysis Subject to the use restrictions above the HDD data logged may be transferred to entities located outside of your country or region of residence e g European Union Those countries
16. audio device while playing media files Do not change the display device under the following conditions E While data is being read or written E While communication is being carried out Selecting HD Format To select the display mode follow the steps as below 1 Click Start gt Control Panel gt Appearance and Personalization gt Display gt Change display settings gt Advanced settings gt List All Modes 2 Select one of the modes at List All Modes Changing the display settings After one or more external displays are connected the operating system can automatically detect identify and setup the display settings You can also manually manage how the external displays will work and change the display settings by pressing P while holding down the Windows H key If you disconnect the external display before you turn the computer s power off be sure to switch to the internal display Security lock A security lock enables you to anchor your computer to a desk or other heavy object in order to help prevent unauthorized removal or theft The computer has a security lock slot on its right side into which you can attach User s Manual 4 30 one end of the security cable while the other end attaches to a desk or similar object The methods used for attaching security cables differ from product to product Please refer to the instructions for the product you are using for more information Connecting the security
17. be corrupted in these instances try loading another copy of the software if possible If an error message appears while you are using a software package you should refer to the documentation supplied with it as this will usually include a problem solving section or a summary of error messages Next you should check any error messages against the operating system documentation A Hardware If you cannot find a software problem you should then check the setup and configuration of your hardware First run through the items in the preliminary checklist as described previously then if you still cannot correct the problem try to identify the source the next section provides checklists for individual components and peripherals Before using a peripheral device or application software that is not an authorized TOSHIBA part or product make sure the device or software can be used with your computer Use of incompatible devices may cause injury or may damage your computer If something goes wrong User s Manual Your computer does not respond to the keyboard commands If an error occurs and the computer does not respond to your keyboard commands follow the steps below Press the power button and hold it down for five seconds Once the computer has turned itself off wait between ten and fifteen seconds before turning the power on again by pressing the power button Your program stops responding If you are working with a progra
18. by the design of individual components Published battery life numbers are achieved on select models and configurations tested by TOSHIBA at the time of publication Recharge time varies depending on usage Battery may not charge while computer is consuming full power After going through many charge and discharge cycles the battery will lose its ability to perform at maximum capacity and will need to be replaced This is a normal phenomenon for all batteries To purchase a new battery pack see the accessories information that is shipped with your computer Hard Disk Drive HDD Capacity LCD 1 Gigabyte GB means 10 1 000 000 000 bytes using powers of 10 The computer operating system however reports storage capacity using powers of 2 for the definition of 1 GB 230 1 073 741 824 bytes and therefore shows less storage capacity Available storage capacity will also be less if the product includes one or more pre installed operating systems such as Microsoft Operating System and or pre installed software applications or media content Actual formatted capacity may vary Over a period of time and depending on the usage of the computer the brightness of the LCD screen will deteriorate This is an intrinsic characteristic of LCD technology Maximum brightness is only available when operating in AC power mode Screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the s
19. computer s power While holding down F12 key on the keyboard turn on your computer when the TOSHIBA Leading Innovation gt gt gt logo screen appears release the F12 key Use the up and down cursor key to select the appropriate option from the menu according to your actual recovery media 5 Amenu will be displayed from which you should follow the on screen instructions If you have previously chosen to remove the recovery partition and are trying to create Recovery Media you will see the following message The Recovery Media Creator can not be launched because there is no recovery partition When there is no recovery partition the Recovery Media Creator cannot make Recovery Media However if you have already created a Recovery Media you can use it to restore the recovery partition If you have not created Recovery Media please contact TOSHIBA Support for assistance Restoring the pre installed software from the Recovery Hard Disk Drive A portion of the total Hard Disk Drive space is configured as a hidden recovery partition This partition stores files which can be used to restore pre installed software in the event of a problem If you subsequently set up your Hard Disk Drive again do not change delete or add partitions in a manner other than specified in the manual otherwise you may find that space for the required software is not available In addition if you use a third party partitioning program to rec
20. contact TOSHIBA Support As of March 2014 Austria Cyprus Finland Hong Kong Indonesia Korea Luxemburg Norway Romania Sweden Belgium Czech Rep France Hungary Ireland Latvia Malta Philippines Slovak Republic Switzerland Non applicable Icons CPU User s Manual Bulgaria Denmark Germany Iceland Italy Liechtenstein Monaco Poland Slovenia UK Canada Estonia Greece India Japan Lithuania Netherlands Portugal Spain USA Certain computer chassis are designed to accommodate all possible configurations for an entire product series Therefore please be aware that your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis Central Processing Unit CPU Performance Legal Footnotes CPU performance in your computer product may vary from specifications under the following conditions E use of certain external peripheral products muse of battery power instead of AC power Huse of certain multimedia computer generated graphics or video applications E use of standard telephone lines or low speed network connections use of complex modeling software such as high end computer aided design applications use of several applications or functionalities simultaneously muse of computer in areas with low air pressure high altitude gt 1 000 meters or gt 3 280 feet above sea level use of computer at temp
21. derivative of this code cannot be changed i e this code cannot simply be copied and put under another distribution licence including the GNU Public Licence FreeType License Issues The FreeType Project LICENSE 2006 Jan 27 Copyright 1996 2002 2006 by David Turner Robert Wilhelm and Werner Lemberg User s Manual 1 10 User s Manual Introduction The FreeType Project is distributed in several archive packages some of them may contain in addition to the FreeType font engine various tools and contributions which rely on or relate to the FreeType Project This license applies to all files found in such packages and which do not fall under their own explicit license The license affects thus the FreeType font engine the test programs documentation and makefiles at the very least This license was inspired by the BSD Artistic and IJG Independent JPEG Group licenses which all encourage inclusion and use of free software in commercial and freeware products alike As a consequence its main points are that m We don t promise that this software works However we will be interested in any kind of bug reports as is distribution m You can use this software for whatever you want in parts or full form without having to pay us royalty free usage m You may not pretend that you wrote this software If you use it or only parts of it in a program you must acknowledge somewhere in your documentation that
22. graphics system for graphics performance and therefore reduce the amount of main system memory available for other computing activities The amount of main system memory allocated to support graphics may vary depending on the graphics system applications utilized system memory size and other factors If your computer is configured with more than 3 GB memory the memory might be displayed as approximately 3 GB only depending on the computer s hardware specifications This is correct because the operating system usually displays the available memory instead of the physical memory RAM built into the computer Various system components like the video adapter s GPU and PCI devices like Wireless LAN etc require their own memory space Since a 32 bit operating system cannot address more than 4 GB of memory these system resources overlap the physical memory It is a technical limitation 7 16 that the overlapped memory is not available to the operating system Even though some tools might display the actual physical memory built into your computer the memory available to the operating system will still be approximately 3 GB only Computers configured with a 64 bit operating system can address 4 GB or more of system memory Battery Life Battery life may vary considerably depending on product model configuration applications power management settings and features utilized as well as the natural performance variations produced
23. help to prevent potential negative consequences for the environment and human health For more detailed information about the collection and recycling programmes available in your country please visit our website www toshiba eu recycling or contact your local council office or the retail outlet where you purchased the product A Disposal of batteries and or accumulators The crossed out wheeled dust bin symbol indicates that batteries and or accumulators must be collected and disposed of separately from household waste POME GA If the battery or accumulator contains more than the specified values of lead Pb mercury Hg and or cadmium Cd defined in the European Battery Directive then the chemical symbols for lead Pb mercury Hg and or cadmium Cd will appear below the crossed out wheeled dust bin symbol By participating in the separate collection of batteries you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health To achieve this you should take any battery and or accumulator to your local recycling site or to a retail outlet or facility that offers to collect these devices for environmentally friendly disposal ensuring that the terminal contacts are covered by non conductive tape For more detailed information about the collection and recycling programmes available in your country please visit our webs
24. media and remove it If you remove the memory media or turn off the power while the computer is accessing the memory media you may lose data or damage the media Do not remove the memory media while the computer is in Sleep or Hibernation Mode The computer could become unstable or data in the memory media could be lost Do not remove only the miniSD microSD Card while leaving the adaptor in the memory media slot 4 27 External Display Your computer video capabilities can be enhanced with additional displays External displays allows you to share your desktop or extend the desktop area Connecting an external display T T User s Manual Your computer comes with a built in display but you can also connect other external displays via available ports on the computer E Some models may include the Triple Monitor function that can display image on Triple Monitor independently mAs the port operation of all external display devices have not been confirmed some devices may not function properly External RGB monitor port An external analog monitor can be connected to the External RGB monitor port on the computer To connect an external analog monitor follow the steps as detailed below 1 Connect the RGB cable to the External RGB monitor port 1 External RGB monitor port 2 RGB cable There are no fastening screws for an external monitor cable on the External RGB monitor port However external monitor cables
25. network will have to be configured for all computers connected to the same network in order to re enable network connections Please be sure to use new network name Security TOSHIBA strongly recommend that you enable encryption functionality otherwise your computer will be open to illegal access by an outsider using a wireless connection If this occurs the outsider may illegally access your system eavesdrop or cause the loss or destruction of stored data TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof Card Specifications Compatibility m IEEE 802 11 Standard for Wireless LANs Network Operating m Microsoft Windows Networking System Media Access m CSMA CA Collision Avoidance with Protocol Acknowledgment ACK Radio Characteristics Radio Characteristics of Wireless LAN module may vary according to Country region where the product was purchased Type of product Wireless communication is often subject to local radio regulations Although Wireless LAN wireless networking products have been designed for operation in the license free 2 4GHz and 5GHz band local radio regulations may impose a number of limitations to the use of wireless communication equipment Radio Frequency E Band 5GHz 5150 5850 MHz Revision a and n E Band 2 4GHz 2400 2483 5 MHz Revision b g and n The range of the wireless signal is related to the transm
26. or keyboard wakes the computer in seconds These sleep features can save you up to 23 per year 200 kWh per year in electricity and prevent up to 300 pounds of greenhouse gas emissions annually To learn how to adjust or activate these sleep settings on your computer please go to www energystar gov sleepinstructions To activate sleep settings organization wide quickly and easily through network tools please go to www energystar gov powermanagement Disposing of the computer and the computer s batteries Contact an authorized TOSHIBA service provider for details regarding how to dispose of the computer and the batteries Optical disc drive safety instructions F User s Manual Be sure to check the precautions at the end of this section AN E The drive model employs a laser system To ensure proper use of this product please read this instruction manual carefully and retain for future reference Should the unit ever require maintenance contact an authorized service location E Use of controls adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure E Toprevent direct exposure to the laser beam do not try to open the enclosure Location of the Required Label Sample shown below Location of the label and manufacturing information may vary Location of the required label THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR SUBCHA
27. order to open the display lift the display panel up and position it at a comfortable viewing angle for you Figure 3 6 The front of the computer with the display panel open User s Manual T Figure 3 7 Top side of the touch screen model 1 Microphone 2 Web Camera LED 3 Web Camera 4 Microphone 8 Display hinges 9 Power button 10 Power indicator 11 Keyboard 5 Wireless communication antennas 12 Touch Pad not shown 6 Display screen 7 Stereo speakers 13 Touch Pad control buttons Provided with some models Product appearance depends on the model you purchased Microphone Web Camera LED Web Camera The built in microphone allows you to import and record sounds for your application please refer to the Sound System and Video mode section for more information The Web Camera LED glows when the Web Camera is operating Web Camera is a device that allows you to record video or take photographs with your computer You can use it for video chatting or video conferences using a communication tool Do not point the web camera directly at the sun E Do not touch or press strongly on the web camera lens Doing so may reduce image quality Use an eyeglass cleaner cleaner cloth or other soft cloth to clean the lens if it becomes dirty Wireless communication antennas Depending
28. personels or mass public m The 2Dto3D conversion function uses TOSHIBA s original algorithm to apply a 3D effect to your own 2D videos However note that this function does not provide the same video content as a video originally provided in 3D and does not create a new video in the 3D format but only plays 2D videos in a 3D like mode m The picture generated by 2Dto3D conversion function is not the same as a picture produced for 3D playback use The 2Dto3D conversion function simply uses TOSHIBA s original algorithm to apply pseudo 3D effect to the 2D content mH The Player is set by default in the 2D format By pressing the 2Dto3D conversion function button you decide to activate the 2Dto3D conversion function and therefore decide to watch your 2D content in 3D The Player will not run the 2Dto3D conversion function automatically Please see the warnings in this section as regards potential copyright infringement and confirm you have any necessary authorization User s Manual The Player is intended for playing DVD Video DVD VR and video files and for viewing 2D home video content and other 2D content created by you in 3D The 3D playback of any video content not created by the user may require the direct or indirect permission of third parties where such content is protected by copyright unless otherwise permitted under applicable law The protection of intellectual property rights is essential for TOSHIBA In this respect TOSHIBA un
29. that may be caused by writing or rewriting with this product or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents E Damage that may be caused by using third party equipment or software Given the technological limitations of current optical disc writing drives you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices In view of this it is good practice to make two or more copies of important data in case of any undesired change or loss of the recorded contents Before writing or rewriting User s Manual E Based on TOSHIBA s limited compatibility testing we suggest the following manufacturers of disc media however it must be noted that disc quality can affect write or rewrite success rates Please also be aware that in no event does TOSHIBA guarantee the operation quality or performance of any disc CD R TAIYO YUDEN CO Ltd MITSUBISHI KAGAKU MEDIA CO LTD CD RW Multi Speed High Speed and Ultra Speed MITSUBISHI KAGAKU MEDIA CO LTD DVD R DVD Specifications for Recordable Disc for General Version 2 0 TAIYO YUDEN Co Ltd for 8x and 16x speed media MITSUBISHI KAGAKU MEDIA CO LTD for 8x and 16x speed media Hitachi Maxell Ltd for 8x and 16x speed media DVD R DL MITSUBISHI KAGAKU MEDIA CO LTD for 4x and 8x speed media DVD R MITSUBISHI KAGAKU MEDIA CO LTD for 8x and 1
30. which have connectors with fastening screws can still be used 2 Turn the external monitor s power on When you turn on the power the computer will automatically recognize the monitor and determine whether it is a color or monochrome device When displaying desktop on an external analog monitor desktop is sometimes displayed on the center of the monitor with black bars around desktop with small size At that time please read the manual of the monitor and set the display mode which is supporting at the monitor Then it will be displayed with suitable size with correct aspect ratio 4 28 T User s Manual The HDMI out port HDMI High Definition Multimedia Interface port digitally transfers both video and audio data without reducing the quality HDMI compatible external display devices including televisions can be connected via the HDMI port Some models can support ultra high definition 3840 x 2160 pixels display on compatible external display devices via HDMI output port To use this function you must purchase an HDMI cable corresponding to 3840x2160 pixels or higher To connect an HDMI compatible display device follow the steps as detailed below To connect a device to the HDMI out port you must purchase a suitable HDMI cable 1 Plug one end of the HDMI cable into the HDMI in port of the HDMI display device 2 Plug the other end of the HDMI cable into the HDMI out port on your computer 3 Turn the HDMI d
31. you do not want to record data Inserting memory media User s Manual The following instructions apply to all types of supported media devices To insert memory media follow the steps as detailed below 1 2 Turn the memory media so that the contacts metal areas face down Insert the memory media into the memory media slot on the computer 4 26 3 Press the memory media gently to ensure a firm connection is made The memory media will be partially out of the slot Figure 4 7 Inserting memory media 1 Memory media slot 2 Memory media One Memory media slot is provided either on the front or on the left side of your computer Product appearance depends on the model you purchased Make sure the memory media is oriented properly before you insert it If you insert the media in wrong direction you may not be able to remove it When inserting the memory media do not touch the metal contacts You could expose the storage area to static electricity which can destroy data Do not turn the computer off or switch to Sleep Mode or Hibernation Mode while files are being copied doing so may cause data to be lost Removing memory media A User s Manual The following instructions apply to all types of supported media devices To remove memory media follow the steps as detailed below 1 2 Click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar Select memory media Grasp the
32. you have used the FreeType code credits We specifically permit and encourage the inclusion of this software with or without modifications in commercial products We disclaim all warranties covering The FreeType Project and assume no liability related to The FreeType Project Finally many people asked us for a preferred form for a credit disclaimer to use in compliance with this license We thus encourage you to use the following text Portions of this software are copyright C lt year gt The FreeType Project www freetype org All rights reserved Please replace lt year gt with the value from the FreeType version you actually use Legal Terms Throughout this license the terms package FreeType Project and FreeType archive refer to the set of files originally distributed by the authors David Turner Robert Wilhelm and Werner Lemberg as the FreeType Project be they named as alpha beta or final release User s Manual You refers to the licensee or person using the project where using is a generic term including compiling the project s source code as well as linking it to form a program or executable This program is referred to as a program using the FreeType engine This license applies to all files distributed in the original FreeType Project including all source code binaries and documentation unless otherwise stated in the file in its original unmodified fo
33. 14 VSYNC Vertical Sync Signal O 15 SCL Data Clock Signal O I O I Input to computer I O O Output from computer User s Manual 7 2 AC Power Cord and Connectors The power cord s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country region in which it is used All cords must meet the following specifications Wire size Minimum 0 75 mm Current rating Minimum 2 5 amperes Certification agencies User s Manual China CQC U S and Canada UL listed and CSA certified No 18 AWG Type SVT or SPT 2 Australia AS Japan DENANHO Europe Austria OVE Italy IMQ Belgium CEBEC The Netherlands KEMA Denmark DEMKO Norway NEMKO Finland FIMKO Sweden SEMKO France LCIE Switzerland SEV Germany VDE United Kingdom BSI In Europe two conductors power cord must be VDE type HOSVVH2 F or HO3VVH2 F and for three conductors power cord must be VDE type HOSVV F For the United States and Canada two pin plug configuration must be a 2 15P 250V or 1 15P 125V and three pin plug configuration must be 6 15P 250V or 5 15P 125V as designated in the U S National Electrical code handbook and the Canadian Electrical Code Part II The following illustrations show the plug shapes for the U S A and Canada the United Kingdom Australia Europe and China USA United Kingdom UL approved BS approved Australia E
34. 5GHz channel limitations apply for outdoor usage The user should use the wireless LAN utility to User s Manual 7 10 User s Manual check the current channel of operation If operation is occurring outside of the allowable frequencies for outdoor use as listed above the user must contact the applicable national spectrum regulator to request a license for outdoor operation Canada Industry Canada IC This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Ce dispositif est conforme a la norme CNR 210 d Industrie Canada applicable aux appareils radio exempts de licence Son fonctionnement est sujet aux deux conditions suivantes 1 le dispositif ne doit pas produire de brouillage pr judiciable et 2 ce dispositif doit accepter tout brouillage regu y compris un brouillage susceptible de provoquer un fonctionnement ind sirable Les dispositifs fonctionnant dans la bande 5 15 5 25GHz sont r serv s uniquement pour une utilisation a l int rieur afin de r duire les risques de brouillage pr judiciable aux syst mes de satellites mobiles utilisant les m mes canaux Les utilisateurs devraient aussi tre avis s que les utilisateurs de radars de haute puissance sont d sign s utilisateurs principaux
35. 6x speed media TAIYO YUDEN CO Ltd for 8x and 16x speed media DVD R DL MITSUBISHI KAGAKU MEDIA CO LTD for 8x speed media DVD RW DVD Specifications for Recordable Disc for Version 1 1 or version 1 2 Victor Company of Japan Ltd JVC for 2x 4x and 6x speed media MITSUBISHI KAGAKU MEDIA CO LTD for 2x 4x and 6x speed media DVD RW MITSUBISHI KAGAKU MEDIA CO LTD for 4x and 8x speed media DVD RAM DVD Super Multi drive only DVD Specifications for DVD RAM Disc for Version 2 0 Version 2 1 or Version 2 2 Panasonic Corporation for 3x and 5x speed media Hitachi Maxell Ltd for 3x and 5x speed media BD R Panasonic Corporation BD R DL Panasonic Corporation BD RE Panasonic Corporation BD RE DL Panasonic Corporation BD R TL TDK BD RE TL Panasonic Corporation 1 E Some types and formats of DVD R DL and DVD R DL discs may be I unreadable User s Manual 4 11 Disc created in DVD R DL format4 Layer Jump Recording cannot be read When writing or rewriting Please observe the following points while you write or rewrite data to a media Always copy data from the hard disk drive to the optical media do not use the cut and paste function as the original data will be lost if there is a write error Do not perform any of the following actions E Change users in the Operating Systems m Operate the computer for any other function including such tasks as using a mouse or Touch
36. BA Support Procedure In this instance the system might be busy Try moving the mouse again after waiting a short while Remove the mouse from the computer and then reconnect it to a free USB port in order to ensure it is firmly attached Problem Double clicking does not work The on screen pointer moves too fast or too slow The on screen pointer moves erratically USB device In addition to the information in this section please also refer to the documentation supplied with your USB device User s Manual Problem USB device does not work Procedure In this instance you should initially try changing the double click speed setting within the Mouse Control utility 1 To access this utility click Start gt Control Panel gt Hardware and Sound gt Mouse 2 Within the Mouse Properties window click the Buttons tab 3 Set the double click speed as required and click OK In this instance you should initially try changing the speed setting within the Mouse Control utility 1 To access this utility click Start gt Control Panel gt Hardware and Sound gt Mouse 2 Within the Mouse Properties window click the Pointer Options tab 3 Set the pointer speed as required and click OK The elements of the mouse responsible for detecting movement might be dirty please refer to the documentation supplied with the mouse for instructions on how to clean it If you are still unable to resol
37. Blu ray Disc Player Notes on Use User s Manual This software can only be used on Windows operating system TOSHIBA Blu ray Disc Player is only provided with models configured with a Blu ray Writer drive Playback of high bit rate content may cause frame dropping audio skipping or decrease in computer performance Close all other applications before playing back video Do not open any other applications or carry out any other operations during video playback Do not switch to Hibernation or Sleep Mode when running the TOSHIBA Blu ray Disc Player Because Blu ray Disc playback operates according to programs built into the content operation methods operation screens sound effects icons and other features may vary from disc to disc For more information on these items refer to instructions included with content or contact the content manufacturers directly Make sure to connect the computer s AC adapter when playing a video TOSHIBA Blu ray Disc Player supports AACS Advanced Access Control System copy protection technology Renewal of the AACS key integrated into this product is required for uninterrupted enjoyment of Blu ray Disc An Internet connection is required for renewal AACS key renewal is provided free of charge for 5 years after the purchase of this product however renewal beyond 5 years is subject to conditions specified by the software provider TOSHIBA Corporation Do not playback video while recording te
38. C any company enterprise or user is not allowed to change frequency enhance transmitting power or alter original characteristic as well as performance to an approved low power radio frequency devices Article 14 The low power radio frequency devices shall not influence aircraft security and interfere legal communications If found the user shall cease operating immediately until no interference is achieved The said legal communications means radio communications is operated in compliance with the Telecommunications Act The low power radio frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices Using this equipment in Japan In Japan the frequency bandwidth of 2 400MHz to 2 483 5MHz for second generation low power data communication systems such as this equipment overlaps that of mobile object identification systems premises radio station and specified low power radio station 1 Important notice The frequency bandwidth of this equipment may operate within the same range as industrial devices scientific devices medical devices microwave ovens licensed radio stations and non licensed specified low power radio stations for mobile object identification systems RFID used in factory production lines Other Radio Stations 1 Before using this equipment ensure that it does not interfere with any of the equipment listed above User s Manual 2 If th
39. D RE and BD RE DL Blu ray Writer drive BDXL In addition to the above formats Blu ray Writer drive BDXL supports BD R TL BD R QL and BD RE TL y Some types and formats of DVD R DL and DVD R DL discs may be J unreadable Using optical disc drives The full size drive provides high performance execution of disc based programs You can run either 12 cm 4 72 or 8 cm 3 15 discs without an adaptor 7 Use the DVD playback application to view DVD Video discs For precautions on writing to discs refer to the Writing discs section To load discs follow the steps as detailed below 1 When the computer s power is on press the eject button to open the disc tray slightly User s Manual 4 6 2 Grasp the disc tray gently and pull until it is fully opened Figure 4 2 Pressing the eject button and pulling the disc tray open 1 Eject button 2 Disc tray 3 Lay the disc label side up in the disc tray Figure 4 3 Inserting a disc 1 Laser lens 1 When the disc tray is fully opened the edge of the computer will cover the J disc tray slightly Therefore you will need to turn the disc at an angle when you place it in the disc tray After seating the disc however make sure it lies flat E Do not touch the laser lens or any portion of its surrounding casing as this could cause misalignment m Prevent foreign objects from entering the drive Check the surface of the disc tray especially the area behind the fro
40. For use in other regions please buy power cords that conform to safety rules and regulations in the particular region Do not use a 3 pin to 2 pin conversion plug When you connect the AC adaptor to the computer always follow the steps in the exact order as described in this User s Manual Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched As a general safety precaution avoid touching any metal parts Never place your computer or AC adaptor on a wooden surface furniture or any other surface that could be marred by exposure to heat since the computer base and AC adaptor s surface increase in temperature during normal use Always place your computer or AC adaptor on a flat and hard surface that is resistant to heat damage Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions 1 Connect the power cord to the AC adaptor Figure 2 1 Connecting the power cord to the AC adaptor 2 pin plug PS Figure 2 2 Connecting the power cord to the AC adaptor 3 pin plug a Either a 2 pin or 3 pin adaptor cord will be included with the computer J depending on the model 2 Connect the AC adaptor s DC output plug to the DC IN 19V jack on your computer Figure 2 3 Connecting the DC output plug to the computer
41. HWSetup window contains a number of tabs to allow specific functions of the computer to be configured In addition there are also three buttons OK Cancel and Apply OK Accepts your changes and closes the TOSHIBA HWSetup window Cancel Closes the window without accepting your changes Apply Accepts all your changes without closing the TOSHIBA HWSetup window Some options shown in grey are possible to confirm their status i TOSHIBA HWSetup screen may have the following tabs E General Allows you to view the current BIOS version or change certain settings back to their default values E Password Allows you to set or reset the user password for power on m Display Allows you to select the internal LCD and or external monitor when the computer boots up Boot Setting Allows you to change the sequence in which your computer searches the drives for the operating system Keyboard Allows you to set conditions for the Keyboard USB Allows you to set conditions for USB SATA Allows you to set conditions for SATA LAN Allows you to set conditions for LAN The settings or options explained here may vary depending on the model you purchased After you changed the settings a dialog box may appear to prompt you that the changes will take effect after the computer is restarted Make sure to restart your computer immediately to apply these changes TOSHIBA PC Health Monitor User s Manual The TOSHIBA PC Health Monitor
42. NSED BY MPEG LA TO PROVIDE SUCH VIDEO NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA L L C SEE HTTP WWW MPEGLA COM OpenSSL Toolkit License Issues LICENSE ISSUES The OpenSSL toolkit stays under a dual license i e both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit See below for the actual license texts Actually both licenses are BSD style Open Source licenses In case of any license issues related to OpenSSL please contact openssl core openssl org OpenSSL License Copyright c 1998 2011 The OpenSSL Project All rights reserved Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the above copyright notice this list of conditions and the following disclaimer 2 Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution 3 All advertising materials mentioning features or use of this software must display the following acknowledgment This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http Awww openssl org
43. PTER J APPLICABLE AT DATE OF MANU FACTURE TOSHIBA SAMSUNG STORAGE TECHNOLOGY KOREA CORPORATION 14F Bldg No 102 Digital empire2 486 Sin dong Yeongtong gu Suwon si Gyeonggi do Korea 443 734 CLASS I LASER PRODUCT CAUTION This appliance contains LASER KLASSE LERODUKT a laser system and is classified as a TO EN 60825 1 23A 1 V Bh CLASS 1 LASER PRODUCT To use this model properly read the instruction manual carefully and keep this manual for your future reference In case of any trouble with this model please contact your nearest AUTHORIZED service station To prevent direct exposure to the laser beam do not try to open the enclosure General Precautions TOSHIBA computers are designed to optimize safety minimize strain and withstand the rigors of portability However certain precautions should be observed to further reduce the risk of personal injury or damage to the computer Be certain to read the general precautions below and to note the cautions included in the text of the manual User s Manual 1 15 Provide adequate ventilation Always make sure your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet even if your computer is in Sleep Mode In this condition observe the following Never cover your computer or AC adaptor with any object m Never place your computer o
44. TOSHIBA Leading Innovation gt gt gt User s Manual Satellite L50 B L50D B L50t B L50Dt B Satellite S50 B S50D B S50t B S50Dt B Satellite C55 B C55D B C55t B C55Dt B Satellite Pro L50 B L50D B L50t B L50Dt B Series Table of Contents Chapter 1 Chapter 2 Chapter 3 Chapter 4 User s Manual TOSHIBA Legal Regulatory and Safety Copyright Disclaimer and Trademarks 2 c ceeseeeeeeeeeeeeeeeeeeeeees 1 1 Regulatory Information c ccceceeeeseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeaeeeeeeees 1 2 Video Standard Notice cccecccceceseeeeceeeeeeeeeeeeeeeeeeeeeeeeeseeeeeeeeeeeeeeees 1 7 OpenSSL Toolkit License Issues 2 cceceeeeeeeeeeeeeeeeeeeeeeeeneeeeeeeees 1 8 FreeType License ISSUES ccceeeeeeseeee ee eeeeeeeeeeseseeaeeeeeeseeeeneeeeees 1 10 ENERGY STAR Program cccceceecesseeeeseneeseeeeeeseneeseseeseseseesesseneeenees 1 14 Disposing of the computer and the computer s batteries 1 14 Optical disc drive safety instructions cccceeeseeee ee eeeeeeeeeeees 1 14 General Precautions i e lt lt escsscecic cca scescecceassenecs iessesaiceleccdessececeteaseneass izes 1 15 Safety ICONS ee 1 18 Getting Started Equipment checklist ccccccscsesesecceeeceeseeeeeeeeeeeeeeeeasasnesseesessseseaaaaes 2 1 CONVentOnS 22s face oe sates cc coat aaa a aaa aaa 2 1 Using your computer for the first time ccccesses
45. When a Blu ray Movie Disc is set in the Blu ray drive for models with Blu ray drive TOSHIBA Blu ray Disc Player may start automatically Click Start gt All Programs gt TOSHIBA gt Media amp Entertainment gt TOSHIBA Blu ray Disc Player Operating TOSHIBA Blu ray Disc Player Notes on using TOSHIBA Blu ray Disc Player Screen display and available features may vary amongst Blu ray Videos and scenes Ifthe menu is opened in the Display Area using the Control Panel s Top Menu or Menu buttons Touch Pad and mouse menu operations may not be able to be used Open TOSHIBA Blu ray Disc Player Manual TOSHIBA Blu ray Disc Player features and instructions are explained in details in TOSHIBA Blu ray Disc Player Manual Use the following procedure to open TOSHIBA Blu ray Disc Player Manual m Press the F1 key when TOSHIBA Blu ray Disc Player is launched and click the Help button 3D Playback on an External 3D Device T User s Manual 3D playback on an external 3D device feature is only provided with some models Effect of 3D can be shown only on an external 3D devices connected via an HDMI output It cannot be shown on the internal display In order for 3D playback to work on external display TV you need a 3D enabled display TV that has an HDCP compliant HDMI port 3D playback feature supports the following resolutions 1920x1080 24Hz and 1280x720 60Hz Please change the Screen Resolution to one o
46. ademarks of HDMI Licensing LLC in the United States and other countries Secure Digital and SD are trademarks of SD Card Association MultiMediaCard and MMC are trademarks of MultiMediaCard Association Blu ray Disc Blu ray BDXL and the logos are trademarks of the Blu ray Disc Association DTS the Symbol amp DTS and the Symbol together are registered trademarks and DTS Studio Sound is a trademark of DTS Inc DTS Inc All Rights Reserved Realtek is a registered trademark of Realtek Semiconductor Corporation All other product names and service names in this manual may be trademarks or registered trademarks of their respective companies Regulatory Information FCC information User s Manual FCC notice Declaration of Conformity Information This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment
47. age to either the computer and or the card resulting in computer failure E Always use a suitable carry case when transporting the computer m When carrying your computer be sure to hold it securely so that it does not fall or hit anything Do not carry your computer by holding any of its protruding elements Mobile phones Please be aware that the use of mobile phones can interfere with the audio system The operation of the computer will not be impaired in any way but it is recommended that a minimum distance of 30cm is maintained between the computer and a mobile phone that is in use Instruction Manual for Safety and Comfort All important information on the safe and proper use of this computer is described in the enclosed Instruction Manual for Safety and Comfort Be sure to read it before using the computer Safety Icons A i User s Manual Safety icons are used in this manual to bring important information to your attention Each type of message is identified as shown below Indicates a potentially hazardous situation which could result in death or serious injury if you do not follow instructions A caution informs you that improper use of equipment or failure to follow instructions may cause data loss equipment damage or may result in minor or moderate injury Please read A note is a hint or advice that helps you make best use of your equipment Chapter 2 Getting Started This chapter provides a
48. al Memory Media Card Problem You cannot access a CD DVD Blu ray Disc in the drive Procedure Make sure the drive s disc tray is securely closed Press gently until it clicks into place Open the disc tray and make sure the disc is properly seated It should lie flat with the label facing up A foreign object in the disc tray could block laser light from reading the disc Make sure there is no obstruction Remove any foreign object Check whether the disc is dirty If it is wipe it with a clean cloth dipped in water or a neutral cleaner For further information please refer to Operating Basics Problem Memory media card error occurs You cannot write to a memory media card You cannot read a file Pointing device User s Manual Procedure Remove the memory media card from the computer and then reinsert it in order to ensure it is firmly connected If the problem persists then you should refer to the documentation supplied with your memory media card for further information Remove the memory media card from the computer and check to ensure that it is not write protected Check to ensure the required file is actually on the memory media card that is inserted into the computer If you are still unable to resolve the problem contact TOSHIBA Support If you are using a USB mouse you should also refer to both the USB mouse section and the documentation supplied with your mouse Touch Pad
49. always completely shut down the computer This includes turning off any wireless communication functionalities and cancelling settings that reactivate the computer automatically such as a timer recording function Failure to completely shut down the computer in this way could allow the operating system to reactivate and run pre programmed tasks or preserve unsaved data which could interfere with aviation or other systems possibly causing serious injury Before entering Sleep Mode be sure to save your data gt Do not switch to Sleep Mode while transferring data to external media such as USB devices memory media or other external memory devices Data will be lost 3 m When the AC adaptor is connected the computer will go into Sleep J Mode according to the settings in the Power Options to access it click Start gt Control Panel gt System and Security gt Power Options m 7o restore the operation of the computer from Sleep Mode press and hold the power button or any key on the keyboard for a short amount of time Please note that keyboard keys can only be used if the Wake up on Keyboard option is enabled within the TOSHIBA HWSetup m If the computer enters Sleep Mode while a network application is active the application might not be restored when the computer is next turned on and the system returns from Sleep Mode E 7o prevent the computer from automatically entering Sleep Mode disable Sleep Mode within the Pow
50. apan Only CORBIS PIABRAMRE CT COREL Ria TCE FASS Cee BW CLCWETA CORBMNISAPTLE VAL SB ICIEL CRA SNSC SMBS SROTCEMHVET Friar BABE gt TELL RY RWSL TEAL VCCI B Canadian regulatory information Canada only This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications Note that Canadian Department of Communications DOC regulations provide that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la class B respecte toutes les exgences du R glement sur le mat riel brouileur du Canada Following information is only valid for EU member States Disposal of products User s Manual s The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste Integrated batteries and accumulators can be disposed of with the product They will be separated at the recycling centres The black bar indicates that the product was placed on the market after August 13 2005 By participating in the separate collection of products and batteries you will help to assure the proper disposal of products and batteries and thus
51. become stronger which in turn may cause eye fatigue The 3D effect differs between individuals Please refrain from or stop viewing and check your equipment settings if you can see doubly substituted video images or cannot feel the 3D stereoscopic effect when watching 3D video images Still if you cannot see correctly please refrain from or stop viewing Please refrain from or stop viewing if you feel ill or experience discomfort before or while watching 3D video images Please position yourself directly in front of the display when watching 3D video images And please take regular breaks in between Due to the possibility of impact on vision development viewers of 3D video images should be aged 6 or older Battery Please consider whether it is suitable or is there a need for limiting the viewing time before allowing your child to watch a 3D content m This software does not have parental lock for 3D video viewing Please use the login password functions of Windows if you are worried about the effect of 3D playback on your child s visual function m This software can playback MPEG2 MP4 and WTV files Your own 2D video contents recorded using home video camcorder and other content created by you can be played in either 2D or 3D using real time 2Dto3D conversion As for playback of 3D video content only Side by Side and Interleave 3D video formats are supported E Notall files can be played This section explains battery ty
52. c CD ROM Compact Disc Read only Memory CD RW Compact Disc rewritable CMOS Complementary Metal oxide Semiconductor CPU Central Processing Unit DC Direct Current DDR Double Data Rate DIMM Dual Inline Memory Module DVD Digital Versatile Disc DVD R Digital Versatile Disc recordable DVD RAM Digital Versatile Disc random Access Memory 7 18 User s Manual DVD R DL DVD ROM DVD RW DVD R DL FAT FCC FHD GB GBps HD HD HDD HDMI HDMI CEC HTML IEEE 1 0 IRQ ISP KB LAN LCD LED MB MBps MMC OCR PC PCI PCMCIA RAM RGB RFI Digital Versatile Disc Recordable Dual Layer Digital Versatile Disc read Only Memory Digital Versatile Disc rewritable Digital Versatile Disc Recordable Double Layer File Allocation Table Federal Communications Commission Full High Definition gigabyte gigabytes per second High Definition High Definition Plus Hard Disk Drive High definition Multimedia Interface High definition Multimedia Interface Consumer Electronics Control Hypertext Markup Language Institute of Electrical and Electronics Engineers Input Output interrupt request Internet Service Provider kilobyte Local Area Network Liquid Crystal Display Light Emitting Diode megabyte megabytes per second Multi Media Card Optical Character Recognition Reader Personal Computer Peripheral Component Interconnect Personal Computer Memory Card International As
53. cations and Drivers Special features The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use User s Manual Access each function using the following procedures 1 To access the Power Options click Start gt Control Panel gt System and Security gt Power Options Display automatic power off 1 This feature automatically cuts off power to the computer s display panel when there is no keyboard input for a specified time with power being restored the next time a key is pressed This can be specified in the Power Options User s Manual HDD automatic power off 1 System automatic Sleep Hibernation Mode 1 Power on password Intelligent power supply Battery save mode Panel power on off 1 Low battery automatic Hibernation Mode 1 Sleep Mode This feature automatically cuts off power to the hard disk drive when it is not accessed for a specified time with power being restored when the hard disk drive is next accessed This can be specified in the Power Options This feature automatically shuts down the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time This can be specified in the Power Options Two levels of password security supervisor and user are available to prevent unauthorized access to your computer A microprocessor in the comp
54. caused by extensive keyboard use It also includes information on work space design posture and lighting that can help reduce physical stress Heat injury Avoid prolonged physical contact with the computer If the computer is used for long periods its surface can become very warm While the temperature will not feel hot to the touch if you maintain physical contact with the computer for a long time for example if you rest the computer on your lap or if you keep your hands on the palm rest your skin might suffer a low heat injury If the computer has been used for a long time avoid direct contact with the metal plate supporting the various interface ports as this can become hot The surface of the AC adaptor can become hot when in use but this condition does not indicate a malfunction If you need to transport the AC adaptor you should disconnect it and let it cool before moving it Do not lay the AC adaptor on a material that is sensitive to heat as the material could become damaged Pressure or impact damage Do not apply heavy pressure to the computer or subject it to any form of strong impact as this can damage the computer s components or otherwise cause it to malfunction Cleaning the computer A To help ensure long trouble free operation keep the computer free of dust and dirt and use care with all liquids around it Be careful not to spill liquids into the computer If the computer does get wet turn the power off im
55. ce a less than optimal network performance or even lose your network connection If you should experience any such problem immediately turn off either one of your Bluetooth or Wireless LAN Please visit http www pc support global toshiba com if you have any questions about using Wireless LAN or Bluetooth Module In Europe visit http www toshiba europe com computers tnt bluetooth htm Wireless Devices and your health Wireless products like other radio devices emit radio frequency electromagnetic energy The level of energy emitted by Wireless products however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones Because Wireless products operate within the guidelines found in radio frequency safety standards and recommendations TOSHIBA believes Wireless products are safe for use by consumers These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature In some situations or environments the use of Wireless products may be restricted by the proprietor of the building or responsible representatives of the organization These situations may for example include Using the Wireless products equipment on board of airplanes or E In any other environment where the risk of interference to other devices or serv
56. conditions and the following disclaimer in the documentation and or other materials provided with the distribution 3 All advertising materials mentioning features or use of this software must display the following acknowledgement This product includes cryptographic software written by Eric Young eay cryptsoft com The word cryptographic can be left out if the rouines from the library being used are not cryptographic related 4 If you include any Windows specific code or a derivative thereof from the apps directory application code you must include an acknowledgement This product includes software written by Tim Hudson tjh cryptsoft com THIS SOFTWARE IS PROVIDED BY ERIC YOUNG AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE The licence and distribution terms for any publically available version or
57. creen Graphics Processing Unit GPU User s Manual Graphics processing unit GPU performance may vary depending on product model design configuration applications power management settings and features utilized GPU performance is only optimized when operating in AC power mode and may decrease considerably when operating in battery power mode Total Available Graphics Memory is the total of as applicable Dedicated Video Memory System Video Memory and Shared System Memory Shared System Memory will vary depending on system memory size and other factors Wireless LAN The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment obstacles access point design and configuration and client design and software hardware configurations The actual transmission speed will be lower than the theoretical maximum speed Copy Protection Applicable copy protection standards included in certain media may prevent or limit recording or viewing of the media Glossary User s Manual The terms in this glossary cover topics related to this manual Alternate naming is included for reference Abbreviations AC Alternating Current AMT Intel Active Management Technology ASCII American Standard Code for Information Interchange BIOS Basic Input output System BD ROM Blu ray Disc Read only Memory bps bits per second CD Compact Dis
58. d 1000BASE T User s Manual 4 22 T LAN This section describes how to connect disconnect to a LAN m The Wake up on LAN function consumes power even when the system is off Leave the AC adaptor connected while using this feature m The Link speed 10 100 1000 megabits per second changes automatically depending on the network conditions connected device cable or noise and so on cable types The computer must be configured properly before connecting to a LAN Logging onto a LAN using the computer s default settings could cause a malfunction in LAN operation Check with your LAN administrator regarding set up procedures If you are using Gigabit Ethernet LAN 1000 megabits per second 1000BASE T be sure to connect with a CAT5e cable or higher You cannot use a CAT3 or CAT5 cable If you are using Fast Ethernet LAN 100 megabits per second 100BASE TX be sure to connect with a CAT5 cable or higher You cannot use a CAT3 cable If you are using Ethernet LAN 10 megabits per second 10BASE T you can connect with a CAT3 or higher cable Connecting the LAN cable A User s Manual To connect the LAN cable follow the steps as detailed below E Connect the AC adaptor before connecting the LAN cable The AC adaptor must remain connected during LAN use If you disconnect the AC Adaptor while the computer is accessing a LAN the system may hang up amp Do not connect any other cable to the LAN jack except th
59. derlines that the Player should not be used in a manner infringing such rights It is your responsibility to ensure that you do not infringe any applicable intellectual property laws when you decide to use the Player and more specifically when you decide to activate the 2Dto3D conversion function of the Player Some functions cannot be used during 3D playback In such cases any buttons used for those functions may be disabled Depending on the system environment the player may automatically switch into 2D if you perform any of the following operations during 3D playback Furthermore you may experience some time lag when the switching occurs Opening windows or pop ups such as Right Click Menu Settings Window File Select or Error Message Using Windows features Using any other applications Please make sure to use AC adapter when playing with 3D playback feature enabled Depending on the system environment 3D playback may only be used when the Video Display Window is at full screen 3D playback may not function when windowed In order for the 3D playback to work on an external display TV you need a 3D enabled display TV that has an HDCP compliant HDMI port 3D video content can only be displayed on an external display connected using HDMI with 3D 3D Settings can be changed on the Settings Screen but the default settings are highly recommended Changing the settings may cause the 3D stereoscopic effect to
60. dia oa Q 2 T Secure Digital SD Card microSD card adaptor and microSD card MultiMediaCard MMC User s Manual 4 24 Points to note about the memory media card i SD SDHC SDXC memory cards comply with SDMI Secure Digital Music Initiative which is a technology adopted to prevent unlawful copy or playback of digital music For this reason you cannot copy or playback protected material on another computer or other device and you may not reproduce any copyrighted material except for your personal enjoyment Below is a simple explanation for distinguishing SD memory cards from SDHC memory cards and SDXC memory cards E SD SDHC and SDXC memory cards appear the same externally However the logo on memory cards is different so pay careful attention to the logo when purchasing The SD memory card logo is S2 The SDHC memory card logo is 92 The SDXC memory card logo is 22 E The maximum capacity of SD memory cards is 2GB The maximum capacity of SDHC memory cards is 32GB The maximum capacity of SDXC memory cards is 128GB Memory media format i New media cards are formatted according to specific standards If you wish to reformat a media card be sure to do so with a device that uses media cards Formatting a memory media card Memory media cards are sold already formatted in conformity to specific standards If you reformat a memory card be sure to reformat it with a device such as digital camera or d
61. does not support recording to DVD RAM discs to achieve this you should use Windows Explorer or another similar utility E When you back up a DVD disc be sure that the source drive supports recording to DVD R DVD R DL DVD RW DVD R DVD R DL or DVD RW media if this is not the case then the source disc might not be backed up correctly m When you back up a DVD R DVD R DL DVD RW DVD R DVD R DL or DVD RW disc be sure to use the same type of disc E You cannot partially delete any data written to a CD RW DVD RW or DVD RW disc Data Verification To verify that data has been written or rewritten correctly to a data disc you should follow the steps below before you begin the write rewrite process 1 Click Start gt All Programs gt TOSHIBA gt Media amp Entertainment gt Disc Creator to access the TOSHIBA Disc creator utility User s Manual 4 13 3 4 5 Display the setting dialog box by one of the following two steps Click the Recording settings button for writing on the main toolbar in the Data CD DVD mode Select Settings for Each Mode gt Data CD DVD in the Settings menu Mark the Verify Written Data check box Select File Open or Full Compare mode Click the OK button How to learn more about TOSHIBA Disc Creator Please refer to the Help files for additional TOSHIBA Disc Creator information TOSHIBA Blu ray Disc Player Please be aware of the following limitations when you use TOSHIBA
62. drive to write data to either CD R CD RW DVD R DVD R DL DVD RW DVD R DVD R DL DVD RW or DVD RAM discs You can use the Blu ray Writer drive to write data to either CD R CD RW DVD R DVD R DL DVD RW DVD R DVD R DL DVD RW DVD RAM BD R BD R DL BD RE or BD RE DL discs You can use the Blu ray Writer drive BDXL to write data to either CD R CD RW DVD R DVD R DL DVD RW DVD R DVD R DL DVD RW DVD RAM BD R BD R DL BD RE BD RE DL BD R TL BD R QL or BD RE TL discs When writing information to media using an optical drive you should always ensure that you connect the AC adaptor to a live electrical outlet It is possible that if data is written while powered by the battery pack the write process may sometimes fail due to low battery power in these instances data loss may occur Important message Before you write or rewrite to any of the media supported by the optical disc drive please read and follow all of the setup and operating instructions in this section If you fail to do so you may find that the optical disc drive may not function properly and you may fail to write or rewrite information successfully this may cause you to either lose data or incur other damage to the drive or media Disclaimer TOSHIBA does not assume responsibility for the following E Damage to any disc that may be caused by writing or rewriting with this product m Any change or loss of the recorded contents of media
63. e LAN cable Otherwise malfunctions or damage may occur Do not connect any power supplying device to the LAN cable that is connected to the LAN jack Otherwise malfunctions or damage may occur 1 Turn off the power to all external devices connected to the computer 4 23 2 Plug one end of the cable into the LAN jack Press gently until you hear the latch click into place Figure 4 5 Connecting the LAN cable 1 LAN jack 2 LAN cable 3 Plug the other end of the cable into a LAN hub connector or router Check with your LAN administrator and hardware or software vendor before using or configuring a network connection Memory media The computer is equipped with a memory media slot that can accommodate some kinds of memory media with various memory capacities so that you can easily transfer data from devices such as digital cameras and Personal Digital Assistants AN Keep foreign objects out of the memory media slot Never allow metal objects such as screws staples and paper clips to enter the computer or Keyboard Foreign metal objects can create a short circuit which can cause computer damage and fire possibly resulting in serious injury F mH Please note that an adaptor is required to use miniSD microSD Card m Please note that not all memory media have been tested and verified to work correctly Therefore it is not possible to guarantee that all memory media will operate properly Figure 4 6 Examples of memory me
64. e computer Se o o y ooooceoogo SOoceeronn ol oo o amp le lelo 1 DC IN 19V jack 4 Optical disc drive 2 LAN jack 5 Cooling vents 3 Universal Serial Bus USB 2 0 port 6 Memory media slot Provided with some models One Memory media slot is provided either on the front or on the left side of your computer Product appearance depends on the model you purchased User s Manual 3 2 2 DC IN 19V jack The AC adaptor connects to this jack in order to SE power the computer and charge its internal batteries Please note that you should only use the model of AC adaptor supplied with the computer at the time of purchase using the wrong AC adaptor can cause damage to the computer a LAN jack This jack lets you connect to a LAN The adaptor has built in support for Ethernet LAN 10 megabits per second 10BASE T or Fast Ethernet LAN 100 megabits per second 100BASE TX Some models are equipped with a Gigabit Ethernet LAN 1000 megabits per second 1000BASE T Refer to Operating Basics for details Do not connect any cable other than a LAN cable to the LAN jack It could cause damage or malfunction egi Universal Serial Bus One Universal Serial Bus port which complies to 0 po e 0 standard is provided on the left side USB 2 0 port the USB 2 0 standard i ided on the left sid of the computer The USB 2 0 port is not compatib
65. e on screen instructions Check your Windows manual for more information on backing up your system including the system image backup feature Creating Recovery Media i User s Manual This section describes how to create Recovery Media E Be sure to connect the AC adaptor when you create Recovery Media H Be sure to close all other software programs except the Recovery Media Creator E Do not run software such as screen savers which can put a heavy load on the CPU E Operate the computer at full power E Do not use power saving features E Do not write to the media when the virus check software is running Wait for it to finish then disable virus detection programs including any software that checks files automatically in the background E Do not use utilities including those intended to enhance Hard Disk Drive access speed They may cause unstable operation and damage data B Do not shut down og off or Sleep Hibernate while writing or rewriting the media i Set the computer on a level surface and avoid places subjected to vibrations such as airplanes trains or cars Do not use on an unstable surface such as a stand A recovery image of the software on your computer is stored on the Hard Disk Drive and can be copied to either disc media or USB Flash Memory by using the following steps 1 Select either blank disc or USB Flash Memory The application will allow you to choose from a variety of different
66. e pixel failures of your display is defined according to ISO 9241 307 standards If the number of pixel failures is less than this standard they will not be counted as defect or failure Battery is a consumption product since the battery time depends on the usage of your computer If the battery can not be charged at all then it is a defect or failure The changes in battery time is not a defect or failure Following information is only for India A The use of this symbol indicates that this product may not be treated as household waste By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please visit our website http www toshiba india com or contact call center 1800 200 8674 These symbols may not stick depending on the country and region where you purchased Video Standard Notice User s Manual THIS PRODUCT IS LICENSED UNDER THE AVC THE VC 1 AND MPEG 4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON COMMERCIAL USE OF A CONSUMER FOR I ENCODING VIDEO IN COMPLIANCE WITH THE ABOVE STANDARDS VIDEO AND OR ll DECODING AVC VC 1 AND MPEG 4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND OR WAS OBTAINED FROM A VIDEO PROVIDER LICE
67. ected in order to recharge the battery Amber Indicates the AC adaptor is connected and the battery is charging White Indicates the AC adaptor is connected and the battery is fully charged No light Under any other conditions the indicator does not light 3 If the battery pack becomes too hot while it is being charged the charge J will stop and the DC IN Battery indicator will go out When the battery pack s temperature falls to a normal range charging will resume this process will occur regardless of whether the computer s power is on or off Power indicator Check the Power indicator to determine the power status of the computer the following indicator conditions should be noted White Indicates power is being supplied to the computer and the computer is turned on User s Manual 3 14 User s Manual Flashing white No light Indicates that the computer is in Sleep Mode and that there is sufficient power available AC adaptor or battery to maintain this condition Under any other conditions the indicator does not light Chapter 4 Operating Basics This chapter describes the basic operations of your computer and highlights the precautions that should be taken when using it Using the Touch Screen Some models are equipped with a touch screen You can use your finger to manipulate icons buttons menu items the onscreen keyboard and other items on the touch screen Tap Press and hold I Pinc
68. ed to Off Check to make sure the headphone connection is secure Check within the Windows Device Manager application to ensure the sound device is enabled and that the device is properly working Annoying sound is In this instance you may be experiencing feedback heard from either the internal microphone or an external microphone connected to the computer please refer to Sound System and Video mode for further information Volume cannot be adjusted during Windows start up or shut down If you are still unable to resolve the problem contact TOSHIBA Support External monitor Please also refer to Operating Basics and to the documentation supplied with your monitor for further information User s Manual 6 12 LAN User s Manual Problem Monitor does not turn on No display Display error occurs Problem Cannot access LAN Procedure After confirming that the monitor s power switch is on you should check the connections to make sure that the power cord adaptor is firmly connected to the monitor and to a working power outlet Try adjusting the contrast and brightness controls on the external monitor Press the function key in order to change the display priority and ensure that it is not set for the internal display only Check to see if the external monitor is connected When the external monitor is set as the primary display device in extended desktop mode it will not display when the computer wa
69. eeeeesseeeeseeeneeeeeens 2 2 Turning off the pOWer s s ceeeeeeee cece eeeeeee eee ee ee eeeeeeeeeeeeeeeeeeeneeeeeaees 2 6 The Grand Tour Front with the display closed ccseccceseteeseeeeeeseeeeeeeeesenseeeeeeseneneneens 3 1 EIo E E E E 3 2 Right Sid raira ra a anapa oa a 3 4 ACK EIEEE TE T T A LTAT T EE 3 5 Underside srososorioossia u eee aa aa eaaa Kaanaa tances 3 5 Front with the display open 2 ccccsseeceeeeeeeeeeceeeeeeeeeeeeeeeeeeeneeeeeeeees 3 7 Internal Hardware Components s scseseceeseceeeeeeeeeeseeeneneneneeees 3 10 Power Condition Descriptions ecccsseeseeeeeeseeeeeseeseeeeeeeeeseeeeeees 3 13 Operating Basics Using the Touch Screen eeccseeeeeeeereeeeeeeeeeeeeeeeseeneeeeeeseeseeeeeseeneneseenes 4 1 Using the Touch Pad ecccceseeseeee essen eeeeseeeesseeeeeseeneeeeeeesaseeeesseeneneseees 4 1 The Keyboard h2ievi cain Site seen el Ae eee eee 4 2 Optical disc drives ecesseeeceseeneeeeeeeseneeeeeeeeeseeeeenseneeeeseeseseeeeensnneneeeees 4 5 TOSHIBA Blu ray Disc Player cccccseeeeeseeeeeseeeeeeeeeeesseeeesseeneneseees 4 14 3D Playback on an External 3D Device e ccceeeeeeeeeeeeeeeeeeees 4 16 Battery acca ceca cate te cs case fea Eaa aaa aaa Sa aaea EA a 4 19 EAN oinaan a eaer Oa aaa aN e aaraa a Tasata 4 22 Memory MOG A sisiane dandanadan daa aaaea irinin iaaa 4 24 Chapter 5 Chapter 6 Chapter 7 User s Manual External
70. eep Mode Hibernation Mode or shutdown state User s Manual 5 6 SDS User s Manual This function can be used for ports that support the Sleep and Charge function The port with the icon 4 has Sleep and Charge function You can use the Sleep and Charge function to charge certain USB compatible external devices such as mobile phones or portable digital music players The Sleep and Charge function may not work with certain external devices even if they are compliant with the USB specification In those cases turn the power of the computer ON to charge the device When Sleep and Charge function is enabled USB bus power DC5V will be supplied to compatible ports even when the power of the computer is turned OFF USB bus power DC5V is similarly supplied to the external devices which are connected to the compatible ports However some external devices cannot be charged solely by supplying USB bus power DC5V As for the specifications of the external devices please contact the device manufacturer or check the specifications of the external devices thoroughly before use Using the sleep and charge function to charge external devices will take longer than charging the devices with their own chargers If Sleep and Charge function is enabled the computer s battery will discharge during hibernation or when the computer is turned off It is recommended that you connect the AC adaptor to the computer while using Sleep and Charge
71. er s keyboard contains character keys control keys function keys and special Windows keys providing all the functionality of a full size keyboard Refer to the The Keyboard section for details The Touch Pad located in the palm rest is used to control the movement of the on screen pointer To use the Touch Pad simply touch and move your fingertip across it in the direction you want the on screen pointer to go Touch Pad control The two buttons located on the bottom of the buttons Touch Pad are used like the buttons on a standard mouse press the left button to select a menu item or to manipulate text or graphics designated by the pointer and press the right button to display a menu or other function depending on the software you are using Internal Hardware Components This section describes the internal hardware components of your computer The actual specifications may vary depending on the model you purchased Battery pack This computer includes a battery pack inside However please do not attempt to dismount or replace it by yourself Please contact an authorized TOSHIBA service provider if necessary The rechargeable lithium ion battery pack provides power to the computer when the AC adaptor is not connected For more detailed information on the use and operation of the battery pack please refer to the Battery section Legal Footnote Battery Life For more information regarding Battery Life please refer t
72. er Options E Touse the Hybrid Sleep function configure it in the Power Options Benefits of Sleep Mode The Sleep Mode feature provides the following benefits m Restores the previous working environment more rapidly than the Hibernation Mode feature Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Sleep Mode feature E Allows the use of the panel power off feature Executing Sleep Mode You can enter Sleep Mode in one of following ways HB Click Start Point to the arrow beside the Shut down button and then select Sleep Close the display panel Please note that this feature must be enabled within the Power Options m Press the power button Please note that this feature must be enabled within the Power Options When you turn the power back on you can continue where you left off when you shut down the computer User s Manual 2 8 i When the computer is in Sleep Mode the Power indicator will blink white If you are operating the computer on battery power you can lengthen the overall operating time by turning it off into Hibernation Mode Sleep Mode will consume more power while the computer is off Sleep Mode limitations Sleep Mode will not function under the following conditions Power is turned back on immediately after shutting down Memory circuits are exposed to static electricity or electrical noise Hibe
73. eratures outside the range of 5 C to 30 C 41 F to 86 F or gt 25 C 77 F at high altitude all temperature references are approximate and may vary depending on the specific computer model contact TOSHIBA support for details CPU performance may also vary from specifications due to design configuration Under some conditions your computer product may automatically shut down This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions To avoid risk of lost data always make back up copies of data by periodically storing it on an external storage medium For optimum performance use your computer product only under recommended conditions Read additional restrictions in your product documentation Contact TOSHIBA technical service and support refer to TOSHIBA support section for more information 64 Bit Computing 64 bit processors are designed to take advantage of 32 and 64 bit computing 64 bit computing requires that the following hardware and software requirements are met H 64 bit Operating System mH 64 bit CPU Chipset and BIOS Basic Input Output System H 64 bit Device drivers HB 64 bit applications Certain 32 bit device drivers and or applications may not be compatible with a 64 bit CPU operating system and therefore may not function properly Memory Main System User s Manual Part of the main system memory may be used by the
74. ery 4 19 T User s Manual indicator flashes the computer will enable Hibernation Mode so that you do not lose any data and automatically turn itself off You must recharge a battery pack when it becomes discharged Procedures To recharge a battery pack connect the AC adaptor to the DC IN 19V jack and plug the other end into a working outlet the DC IN Battery indicator will glow amber while the battery is being charged Charging Time The following table shows the approximate time required to fully charge a discharged battery Battery type Power off Power on Battery pack 32Wh 4 about 3 hours about 3 hours cell Battery pack 45Wh 4 about 3 hours about 3 hours cell Please be aware that the charging time when the computer is on is affected by ambient temperature the temperature of the computer and how you are using the computer if you make heavy use of external devices for example the battery might scarcely charge at all during operation Battery charging notice The battery may not begin charging immediately under the following conditions E The battery is extremely hot or cold if the battery is extremely hot it might not charge at all To ensure the battery charges to its full capacity you should charge it at room temperature of between 5 C to 35 C 41 F to 95 F E The battery is nearly completely discharged In this instance you should leave the AC adaptor connected for a few minutes and the batt
75. ery should begin charging The DC IN Battery indicator may show a rapid decrease in battery operating time when you try to charge a battery under the following conditions E The battery has not been used for a long time m The battery has completely discharged and been left in the computer for a long time In such cases you should follow the steps as detailed below 1 Fully discharge the battery by leaving it in the computer with the power on until the system automatically turns itself off 4 20 2 Connect the AC adaptor to the DC IN 19V jack of the computer and to a wall outlet that is supplying power 3 Charge the battery until the DC IN Battery indicator glows white Repeat these steps two or three times until the battery recovers normal capacity Monitoring battery capacity T Remaining battery power can be monitored using the following methods Clicking the battery icon on the Windows Taskbar m Via the Battery Status in the Windows Mobility Center window You should wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time This is because the computer needs this time to check the battery s remaining capacity and then calculate the remaining operating time based on this together with the current power consumption Please be aware that the actual remaining operating time may differ Slightly from the calculated time With repeated discharges and recharg
76. es the battery s capacity will gradually decrease In view of this it will be noted that an often used older battery will not operate for as long as a new battery even when both are fully charged Maximizing battery operating time User s Manual A battery s usefulness depends on how long it can supply power on a single charge while how long the charge lasts in a battery depends on Processor speed Screen brightness System Sleep Mode System Hibernation Mode Display power off period Hard Disk Drive power off period How often and for how long you use the Hard Disk Drive and external disk drives for example optical disc How much charge the battery contained to begin with H How you use optional devices such as a USB device to which the battery supplies power Whether you enable Sleep Mode which can conserve battery power if you are frequently turning the computer off and on m Where you store your programs and data m Whether you close the display panel when you are not using the keyboard closing the display saves power 4 21 E The environmental temperature operating time decreases at low temperatures Whether you enable Sleep and Charge function Batteries exhausted time When you turn off the power of your computer with batteries fully charged the batteries will be exhausted within the following approximate period Battery type Sleep Mode Shut Down Mode Battery pack 32Wh 4 about 3 days about 35 da
77. esn t power the computer Battery Procedure Check the connections to make sure that the power cord adaptor is firmly connected to the computer and a working power outlet Check the condition of the cord and terminals If the cord is frayed or damaged it should be replaced while if the terminals are soiled they should be cleaned with a clean cotton cloth If the AC adaptor still does not power the computer you should contact TOSHIBA Support If you suspect a problem with the battery you should check the status of the DC IN Battery indicator Problem Battery doesn t power the computer Battery doesn t charge when the AC adaptor is attached Battery doesn t power the computer as long as expected User s Manual Procedure The battery may be discharged connect the AC adaptor to recharge the battery If the battery is completely discharged it will not begin charging immediately in these instances you should wait a few minutes before trying again If the battery still does not charge you should check that the power outlet the AC adaptor is connected to is supplying power this can be tested by plugging another appliance into it If you frequently recharge a partially charged battery the battery might not charge to its full potential in these instances you should fully discharge the battery and then attempt to charge it again Check the Power saver option under Select a power plan in the Power O
78. essibility Windows special keys The keyboard provides two keys that have special functions in Windows the Windows logo key activates the Start menu while the application key has the same function as the secondary right mouse button oo 5B This key activates the Windows Start menu This key has the same function as the secondary right mouse button Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation but you are able to generate these characters using their specific ASCII codes 1 Hold down the ALT key 2 Using the numeric keypad type the ASCII code of the character you require 3 Release ALT the ASCII character will appear on the display screen Optical disc drives The computer may be installed with a DVD Super Multi drive or Blu ray Writer drive BDXL When the computer is accessing an optical disc the indicator on the drive glows User s Manual 4 5 Formats The drives support the following formats DVD Super Multi drive The drive supports the following formats CD ROM DVD ROM DVD Video CD DA CD Text Photo CD single multi session CD ROM Mode 1 Mode 2 CD ROM XA Mode 2 Form1 Form2 Enhanced CD CD EXTRA Addressing Method 2 DVD R DVD RW DVD R DVD RW DVD RAM DVD R DL Format1 DVD R DL Blu ray Writer drive In addition to the above formats Blu ray Writer drive supports BD ROM BD ROM DL BD R BD R DL B
79. estores the computer from Sleep Mode depending on the external devices connected to the USB ports For example if a mouse or USB keyboard is connected to a USB port clicking the mouse button or pressing the keyboard will wakeup the computer Heat dispersal To protect against overheating the processor is equipped with an internal temperature sensor which activates a cooling fan or lowers the processing speed if the computer s internal temperature rises to a certain level You are able to select whether to control this temperature by either turning on the fan first then if necessary lowering the processor speed or by lowering the processor speed first then if necessary turning on the fan Both of these functions are controlled through the Power Options When the processor s temperature falls within normal range the fan and the processor operation will return to its standard speed If the processor s temperature reaches an unacceptably high level with either setting the computer automatically shuts down to prevent any damage In this instance all unsaved data in memory will be lost Using the TOSHIBA Sleep Utility The TOSHIBA Sleep Utility is used for changing settings of the following function s m Sleep and Charge It also displays the remaining battery capacity Sleep and Charge Your computer can supply USB bus power DC5V to the USB port even when the power of the computer is turned OFF Power OFF includes Sl
80. f the above before using 3D playback function Important Safety Information for 3D Function H Please refrain from or stop viewing if you feel ill or experience discomfort before or while watching 3D video images m Please refrain from viewing 3D video images if you experience convulsions photosensitivity reaction or heart disease m Due to the possibility of impact on vision development viewers of 3D video images should be aged 6 or older Children and teenagers may be more susceptible to health issues associated with viewing in 3D and should be closely supervised to avoid prolonged viewing without rest E Avoid use of the 3D function when under the influence of alcohol Please read the user s manual that comes with the computer carefully before using the 3D playback function E The 3D effect differs between individuals Notes on 3D Playback for TOSHIBA Blu ray Disc Player User s Manual The 3D playback function can playback 3D video content and your 2D home video content and other 2D content created by you DVD or video file in 3D using real time 2Dto3D conversion H The 3D playback function CANNOT be used to playback 2D video contents of Blu ray Disc or AVCHD in 3D using real time 2Dto3D conversion H The Player s 3D playback function is meant for only personal home use Please take note that applicable copyright laws may prohibit the public display when you offer 3D viewing of third party video contents to unidentified
81. for Sleep and Charge function Auto Mode Default is suitable for a wide range of digital audio players However determining which mode is suitable for your USB device is unknown without trying Try each mode using the following procedure from Auto Mode to Alternate Mode to find the suitable mode for your USB device to charge This function may not be able to be used with some connected external devices even if the appropriate mode is selected In this situation clear the Enable Sleep and Charge check box and stop using this function Battery Settings This utility can be used to specify the lower limit of remaining battery life for Sleep and Charge Move the slider bar to specify the lower limit If the remaining battery life falls below the setting the Sleep and Charge function will be stopped Clearing the Enable under Battery Mode check box sets the utility to only charge when the AC adaptor is connected TOSHIBA Password utility F The TOSHIBA Password utility provides two levels of password security User and Supervisor Passwords set by the TOSHIBA Password utility function are different from the Windows password User Password User s Manual To set or reset the user password for power on click the following items Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt HWSetup gt Password This option lets you register a new password or change remove an existing password Not Registered
82. function External devices connected to the USB bus power DC5V function that interfaces with the power ON OFF of the computer may always be in an operational state When there is a current overflow of the external devices connected to the compatible ports USB bus power DC5V supply may be stopped for safety reasons When Sleep and Charge function is enabled the USB Wakeup function may not work for compatible ports In that case if there is a USB port that does not have the Sleep and Charge function attach the mouse or keyboard to it If all USB ports have the Sleep and Charge function change to disable Sleep and Charge function The USB Wakeup function will now work but the Sleep and Charge function will be disabled Metal paper clips or hair pins clips will generate heat if they come into contact with USB ports Do not allow USB ports to come into contact with metal products for example when carrying the computer in your bag Starting the TOSHIBA Sleep Utility To start the utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Sleep Utility Enabling Sleep and Charge This utility can be used to enable and disable the Sleep and Charge function Select the Enable Sleep and Charge check box to enable this function for the compatible USB ports The default state is disabled Power supply mode settings Your PC has multiple charging modes so that many different USB devices can be supported
83. gt DTS Inc gt DTS Sound U S patents apply to this product See http patents dts com Manufactured under license from DTS Licensing Limited 4 32 Video mode T User s Manual Video mode settings are configured via the Screen Resolution dialog To open the Screen Resolution dialog click Start gt Control Panel gt Appearance and Personalization gt Display gt Change display settings If you are running some applications for example a 3D application or video playback you may see some disturbance flickering or frame dropping on your screen If that occurs adjust the resolution of display lowering it until the screen is displayed properly 4 33 Chapter 5 Utilities and Advanced Usage This chapter describes the utilities and special features of this computer and the advanced usage of some utilities Utilities and Applications This section describes the pre installed utilities that come with the computer and details how to start them For further information on their operation you may refer to each utility s online manual help files or README TXT file if applicable User s Manual TOSHIBA HWSetup TOSHIBA Peak Shift Control TOSHIBA PC Diagnostic Tool TOSHIBA Hi Speed Start This utility allows you to customize your hardware settings according to the way you work with the computer and the peripherals you use TOSHIBA Peak Shift Control is a function that can help reduce power u
84. h or stretch 4 X D Rotate N Y Slide Using the Touch Pad Simply tap your finger on the touch screen to act on items on the screen Similar to left click Press your finger down and leave it there for a few seconds This will show information to help you learn more about an item or will open a menu specific to what you are doing Similar to right click Touch the screen or an item with two or more fingers and then move the fingers toward each other pinch or away from each other stretch This will visually Zoom in or out Put two or more fingers on an item and then turn your hand to rotate things in the direction you turn your hand Only some items can be rotated Drag your finger on the touch screen to move through what s on the screen The Touch Pad located in the palm rest may support the following gestures User s Manual Tap Simply tap your finger on the Touch Pad to act on items on the screen Similar to left click Pinch or stretch Place two or more fingers down on the Touch Pad and move them toward each other pinch or away from each other stretch This will visually zoom in or out Two Finger Scroll Place two fingers down and slide them vertically or horizontally from anywhere on the Touch Pad This allows you to operate the scroll bars of a window 4 lt Gg 7 Some of the Touch Pad operations described in this section are only J supported in certain applications The Keyboard The nu
85. he display panel in the closed position Figure 3 1 Front of the computer with display panel closed 1 Memory media slot 3 Wireless communication indicator 2 DC IN Battery indicator One Memory media slot is provided either on the front or on the left side of your computer Product appearance depends on the model you purchased sz Memory media slot This slot lets you insert an SD SDHC SDXC memory card miniSD microSD Card and MultiMediaCard Refer to the Memory media section for more information AN Keep foreign metal objects such as screws staples and paper clips out of the Memory media slot Foreign metal objects can create a short circuit which can cause damage and fire possibly resulting in serious injury User s Manual 3 1 DC IN Battery The DC IN Battery indicator shows the condition indicator of the DC IN and the battery s charge white indicates the battery is fully charged while the power is being correctly supplied from the AC power adaptor Please refer to the Power Condition Descriptions section for more information on this feature yp Wireless The Wireless communication indicator glows communication amber when the Bluetooth or Wireless LAN indicator functions are turned on Only some models are equipped with Bluetooth and Wireless LAN functions Left side The following figure shows the left side of the computer Figure 3 2 The left side of th
86. his feature you can disable it The Display Power Saving Technology feature can be disabled in the Intel HD Graphics Control Panel Intel Graphics and Media Control Panel You can access this control panel in the following way BH Right click on the desktop and click Graphics Properties In Intel HD Graphics Control Panel 1 Click Power and select On battery 2 Click Off under Display Power Saving Technology 3 Click Apply If you want to enable this feature under the conditions mentioned above click On under Display Power Saving Technology In Intel Graphics and Media Control Panel 1 Click Power 2 Select On battery from the drop down menu in Power Source 3 Clear the Display Power Saving Technology check box 4 Click OK If you want to enable this feature under the conditions mentioned above select the Display Power Saving Technology check box AMD Vari Bright AMD GPU models may include the AMD Vari Bright feature that can save the computer s power consumption by optimizing picture contrast on the internal LCD This feature can be used if the computer is E running under battery mode H using the internal LCD display only The Vari Bright feature can be enabled in the AMD VISION Engine Control Center Catalyst Control Center You can access the center in the following way H Right click on the desktop and click AMD VISION Engine Control Center Catalyst Control Center In this control pane
87. hone recording level 1 Right click on the speaker icon on the Windows Taskbar and select Recording devices from the sub menu 2 Select Microphone and click Properties 3 On the Levels tab move the Microphone slider to increase or decrease the microphone volume level If you feel the microphone volume level is inadequate move the Microphone Boost slider to a higher level Audio Enhancements In order to apply the sound effects for your current speaker follow the steps below 1 Right click on the Speakers icon on the Windows Taskbar and then select Playback devices from the sub menu 2 Select Speakers and click Properties 3 On the Enhancements tab select the sound effects you would like and click Apply DTS Sound User s Manual DTS Sound utilizes advanced patented techniques to retrieve audio cues buried in the original source material and deliver immersive surround sound complete with deep rich bass and crystal clear dialog DTS Sound is provided with some models It provides the following features E Immersive surround sound with bass and dialog enhancement E Broad sweet spot with elevated sound image E Improved volume output delivering maximum volume without creating clipping or distortion H Dialog enhancement for clear and intelligible vocals m Bass enhancement for rich low frequency production High frequency definition for crisp details To access the utility click Start gt All Programs
88. ic Compatibility requirements to be observed for so called Residential commercial and light industry environments TOSHIBA do not approve the use of this product in working environments other than the above mentioned Residential commercial and light industry environments For example the following environments are not approved E Industrial Environments e g environments where a mains voltage of 380 V three phase is used E Medical Environments E Automotive Environments E Aircraft Environments Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of TOSHIBA The consequences of the use of this product in non approved working environments may be Interference with other devices or machines in the near surrounding area Malfunction of or data loss from this product caused by disturbances generated by other devices or machines in the near surrounding area Therefore TOSHIBA strongly recommend that the electromagnetic compatibility of this product should be suitably tested in all non approved working environments before use In the case of automobiles or aircraft the manufacturer or airline respectively should be asked for permission before use of this product Furthermore for general safety reasons the use of this product in environments with explosive atmospheres is not permitted User s Manual 1 4 VCCI Class B Information J
89. ices is perceived or identified as harmful If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment e g airports you are encouraged to ask for authorization to use the Wireless device prior to turning on the equipment Wireless LAN Technology The computer s wireless communication function supports some wireless communication devices Only some models are equipped with both Wireless LAN and Bluetooth functions User s Manual 7 5 User s Manual Do not use the Wireless LAN Wi Fi or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields Interference from a microwave oven or other source can disrupt Wi Fi or Bluetooth operation Turn all wireless functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device Radio waves may affect pacemaker or medical device operation possibly resulting in serious injury Follow the instruction for your medical device when using any wireless functionality Always turn off wireless functionality if the computer is near automatic control equipment or appliances such as automatic doors or fire detectors Radio waves can cause malfunction of such equipment possibly resulting in serious injury It may not be possible to make a network connection to a specified network name using the ad hoc network function If this occurs the new
90. igital audio player that uses the memory cards not with the format command provided within Windows Should you need to format all areas of the memory card including the protected area you will need to obtain an appropriate application that applies the copy protection system Media care User s Manual Observe the following precautions when handling the card H Do not twist or bend cards Do not expose cards to liquids or store in humid areas or lay media close to containers of liquid E Do not touch the metal part of a card or expose it to liquids or let it get dirty m After using card return it to its case 4 25 T A The card is designed so that it can be inserted only one way Do not try to force the card into the slot Do not leave a card partially inserted in the slot Press the card until you hear it click into place Set the write protect switch to the lock position if you do not want to record data Memory cards have a limited lifespan so it is important to backup important data Do not write to a card if the battery power is low Low power could affect writing accuracy Do not remove a card while read write is in progress For more details on using memory cards see manuals accompanying the cards About the write protect feature Memory media cards have a write protect function SD Card SD memory card SDHC memory card and SDXC memory card Set the write protect switch to the lock position if
91. imer that states that the software is based in part of the work of the FreeType Team in the distribution documentation We also encourage you to put an URL to the FreeType web page in your documentation though this isn t mandatory These conditions apply to any software derived from or based on the FreeType Project not just the unmodified files If you use our work you must acknowledge us However no fee need be paid to us 3 Advertising User s Manual Neither the FreeType authors and contributors nor you shall use the name of the other for commercial advertising or promotional purposes without specific prior written permission We suggest but do not require that you use one or more of the following phrases to refer to this software in your documentation or advertising materials FreeType Project FreeType Engine FreeType library or FreeType Distribution As you have not signed this license you are not required to accept it However as the FreeType Project is copyrighted material only this license or another one contracted with the authors grants you the right to use distribute and modify it Therefore by using distributing or modifying the FreeType Project you indicate that you understand and accept all the terms of this license 4 Contacts There are two mailing lists related to FreeType E freetype nongnu org Discusses general use and applications of FreeType as well as future and wan
92. ings by using it continuously TOSHIBA eco Utility helps control the power consumption of your computer Various information can help you understand your degree of contribution to the environment To access this utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt eco Utility For details on TOSHIBA eco utility see the help file You can create CDs and DVDs in a number of formats including audio CDs that can be played on a standard CD player and data discs which can store copies of the files and folders on your computer s hard disk drive To start this utility click Start gt All Programs gt TOSHIBA gt Media amp Entertainment gt Disc Creator This utility includes wizard functions to monitor the Disk Drive operating status and execute the system backup To access the utility click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt HDD SSD Alert This software is provided for playback of Blu ray Disc It has an on screen interface and functions To start this utility click Start gt All Programs gt TOSHIBA gt Media amp Entertainment gt TOSHIBA Blu ray Disc Player This utility is able to either enable or disable the following functions m Sleep and Charge By connecting to the USB port devices such as digital audio players are able to charge even when the computer is in Standby Sleep Mode Hibernation Mode or shutdown state To
93. is equipment causes RF interference to other radio stations promptly change the frequency being used change the location of use or turn off the source of emissions 3 Contact an authorized TOSHIBA service provider if you have problems with interference caused by this product to Other Radio Stations 2 Indication for Wireless LAN The indication shown below appears on this equipment 1 2 34 Ll 2 4 This equipment uses a frequency of 2 4GHz DS This equipment uses DS SS modulation OF This equipment uses OFDM modulation 4 The interference range of this equipment is less than 40m This equipment uses a frequency bandwidth from 2 400MHz to 2 483 5MHz It is possible to avoid the band of mobile object identification systems akwWN gt s gt 3 Indication for Bluetooth The indication shown below appears on this equipment 1 2 3 Lt 4 2 4 This equipment uses a frequency of 2 4 GHz FH This equipment uses FH SS modulation 1 The interference range of this equipment is less than 10m This equipment uses a frequency bandwidth from 2 400 MHz to 2 483 5 MHz It is impossible to avoid the band of mobile object identification systems PONS 4 About the JEITA 5GHz Wireless LAN supports W52 W53 W56 Channel IEEE802 11b g n IEEE802 11a n w56 Device Authorization This device obtains the Technical Regulation Conformity Certification and it belongs to the device class of
94. is slot and then connected to a desk or other large object in order to deter theft of the computer Back The following figure shows the back of the computer Figure 3 4 The back of the computer _ Product appearance depends on the model you purchased Underside The following figures show the underside of the computer You should ensure that the display is closed before the computer is turned over to avoid causing any damage User s Manual 3 5 Figure 3 5 The underside of the computer oj 1 Cooling vents 2 Battery pack Product appearance depends on the model you purchased Cooling vents The cooling vents help the processor to avoid overheating AN Do not block the cooling vents Keep foreign metal objects such as screws staples and paper clips out of the cooling vents Foreign metal objects can create a short circuit which can cause damage and fire possibly resulting in serious injury Carefully clean the dust on the cooling vents surface using a soft cloth Battery pack The rechargeable lithium ion battery pack provides power to the computer when the AC adaptor is not connected For more detailed information on the use and operation of the battery pack please refer to the Battery section User s Manual 3 6 Front with the display open This section shows the computer with the display panel open In
95. iscs with high definition content are required for HD viewing This software can only playback MPEG2 MP4 and WTV files created by the preinstalled applications on the same computer Playback may not function properly if you use the files other than these types The playback of some media files may not be normal by this player This may also happen when using Windows Media Player and Video app Display Devices amp Audio User s Manual If the video image is not displayed on an external display or television stop the TOSHIBA Blu ray Disc Player and change the screen resolution To change the screen resolution click Start gt Control Panel gt Appearance and Personalization gt Display gt Adjust resolution However video cannot be output to some external displays and televisions due to output or playback conditions When viewing video on an external display or TV change the display device before playing Video can be played only on internal LCD displays or external displays In Clone mode Dual View TOSHIBA Blu ray Disc Player may not function properly Do not change the screen resolution while running the TOSHIBA Blu ray Disc Player H Do not change the display device while running the TOSHIBA Blu ray Disc Player Starting TOSHIBA Blu ray Disc Player Use the following procedure to start TOSHIBA Blu ray Disc Player E Inserta Blu ray Movie Disc in the optical disc drive while the operating system is running
96. isplay device s power on Figure 4 9 Connecting the HDMI out port 1 HDMI out port 2 HDMI cable Please do not plug unplug an HDMI device under the following conditions m The system is starting up m The system is shutting down When you connect a television or external monitor to the HDMI port the display output device is set to HDMI When you unplug the HDMI cable and re plug it please wait at least 5 seconds before you re plug the HDMI cable again When you change the display output device the playback device may not switch automatically In this case in order to set the playback device to the 4 29 same device as the display output device please adjust the playback device manually by the following steps 1 Click Start gt Control Panel gt Hardware and Sound gt Sound 2 In the Playback tab select the playback device which you want to switch to 3 To use the internal speakers on your computer select Speakers To use the television or the external monitor that you have connected to the computer select a different playback device 4 Click the Set Default button 5 Click OK to close the Sound dialog Settings for display video on HDMI To view video on the HDMI display device be sure to configure the following settings otherwise you may find that nothing is displayed T Be sure to use the function key to select the display device before starting J to play video Do not change the display device or
97. it rate of the wireless communication Communications at lower transmit range may travel larger distances E The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high density materials H Range is also impacted due to obstacles in the signal path of the radio that may either absorb or reflect the radio signal Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5 15 to 5 25GHz frequency range High power radars are allocated as primary users i e priority users of the bands 5 25 to 5 35GHz and 5 65 to 5 85GHz and that these radars could cause interference and or damage to LE LAN devices Bluetooth wireless technology User s Manual Some computers in this series have Bluetooth wireless communication function which eliminates the need for cables between electronic devices such as computers printers and mobile phones When it is enabled Bluetooth provides the wireless personal area network environment which is safe and trustworthy that is quick and easy You cannot use the computer s built in Bluetooth functions and an external Bluetooth adaptor simultaneously For reference Bluetooth wireless technology has the following features Security Two advanced security mechanisms ensure a high level of security H Authentication prevents access to critical data and makes it impossible to falsify the origin of a message
98. ite www toshiba eu recycling or contact your local council office or the retail outlet where you purchased the product These symbols may not stick depending on the country and region where you purchased REACH Compliance Statement User s Manual The European Union EU chemical regulation REACH Registration Evaluation Authorization and Restriction of Chemicals entered into force on 1 June 2007 with phased deadlines to 2018 Toshiba will meet all REACH requirements and is committed to provide our customers with information about the presence in our articles of substances included on the candidate list according to REACH regulation Please consult the following website www toshiba eu reach for information about the presence in our articles of substances included on the candidate list according to REACH ina concentration above 0 1 weight by weight Following information is only for Turkey E Disposal of products The crossed wheelie bin symbol means that this ps product should not be collected and disposed with other household wastes When product become waste at the end of life to protect environment and human health it should be given to nearest collection recycling or disposal center For more information about collection and recycling programs in your country please contact your local authority or the retailer where the product was purchased Compliant with AEEE Directive The number of possibl
99. ive force when opening or closing the display panel Turning on the power This section describes how to turn on the power the Power indicator will then indicate the status Please refer to the Power Condition Descriptions section for more information T m After you turn on the power for the first time do not turn it off until you J have set up the operating system E Volume cannot be adjusted during Windows Setup 1 Open the display panel 2 Press the computer s power button Figure 2 5 Turning on the power 1 Power button Product appearance depends on the model you purchased Initial setup The Windows Startup Screen will be the first screen displayed when you turn on the power Follow the on screen instructions on each screen in order to properly install the operating system y When it is displayed be sure to read the License Terms carefully Turning off the power The power can be turned off in one of the following modes either Shut Down Mode Sleep Mode or Hibernation Mode Shut Down Mode When you turn off the power in Shut Down Mode no data will be saved and the computer will boot to the operating system s main screen the next time it is turned on 1 Ifyou have entered data either save it to the Hard Disk Drive or to other storage media User s Manual 2 6 A 2 Make sure all disk disc activity has stopped before removing the disk disc amp fyou turn off the power while a disk disc
100. kes up from Sleep Mode if the external monitor has been disconnected while in Sleep Mode To keep this from happening do not disconnect the external monitor while the computer is in Sleep or Hibernation Mode Remember to turn off the computer before disconnecting the external monitor When the display panel and an external monitor are set to clone mode and they are turned off by the timer the display panel or the external monitor may not display when turned on again If this occurs press the function key to re set the display panel and external monitor to clone mode Check that the cable connecting the external monitor to the computer is firmly attached If you are still unable to resolve the problem contact TOSHIBA Support Procedure Check for a firm cable connection between the LAN jack and the LAN hub Problem Wake up on LAN does not work Wireless LAN Problem Cannot access Wireless LAN Bluetooth Problem Cannot access Bluetooth device TOSHIBA support Procedure Make sure the AC adaptor is connected The Wake up on LAN function consumes power even when the system is off If problems persist consult your LAN administrator Procedure Make sure the computer s Wireless communication function is on If problems persist contact your LAN administrator Procedure Check to ensure the computer s Wireless Communication function is on Check to ensure the Bluetooth Manager application i
101. l 1 Select PowerPlay under Power 2 Select Enable PowerPlay check box and then select the Enable Vari Bright check box If you want to improve the picture quality under the conditions mentioned above adjust the setting towards Maximize Quality or disable this feature Power Condition Descriptions Power conditions i User s Manual The computer s operating capability and battery charge status are affected by different power conditions including whether an AC adaptor is connected and what the charge level is for that battery The LED in the table below refers to the DC IN Battery indicator Power on Power off no operation AC adaptor Battery fully e Operates e No charge connected charged e No charge e LED white e LED white Battery partially Operates Quick charge charged or no e Charge e LED amber charge e LED amber Power on Power off no operation AC adaptor Remaining e Operates not battery capacity LED off connected is above low battery trigger point Remaining e Operates battery capacity LED flashes is below low amber battery trigger point Remaining Computer shuts battery capacity down is exhausted DC IN Battery indicator Check the DC IN Battery indicator to determine the status of the battery pack and the power status with the AC adaptor connected The following indicator conditions should be noted Flashing amber The battery charge is low The AC adaptor must be conn
102. le with USB 3 0 devices 3 m Please note that it is not possible to confirm the operation of all J functions of all USB devices that are available Some functions associated with a specific device might not operate properly Before removing a USB device from the USB port of your computer click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar and then select the USB device that you want to remove AN Keep foreign metal objects such as screws staples and paper clips out of the USB port Foreign metal objects can create a short circuit which can cause damage and fire possibly resulting in serious injury Optical disc drive The computer may be configured with a DVD Super Multi drive or Blu ray Writer drive 2 6GB and 5 2GB DVD RAM media cannot be read from or written to i User s Manual 3 3 SDP Cooling vents The cooling vents help the processor to avoid overheating Memory media slot This slot lets you insert an SD SDHC SDXC memory card miniSsD microSD Card and MultiMediaCard Refer to the Memory media section for more information Right side T User s Manual The following figure shows the right side of the computer Figure 3 3 The right side of the computer o vo O O O 9 1 Headphone Microphone combo jack 5 External RGB monitor port 2 Universal Serial Bus USB 3 0 port 6 Cooling vents 3 Universal Serial Bus USB 2 0 or 3 0
103. levision programs using other applications Doing so may cause video playback or television program recording errors In addition if pre scheduled recording starts during video playback it may cause video playback or television program recording errors Please view video during times when there is no recording prescheduled While playing a BD J title keyboard shortcut is ineffective Resume play function cannot be used with some discs on TOSHIBA Blu ray Disc Player The interactive function on Blu ray discs may not work depending on the contents or network situation Blu ray drives and their associated media are manufactured according to the specifications of three marketing regions Region codes can be set from TOSHIBA Blu ray Disc Player Click the Settings button in the Control Panel And click the Blu ray Region Setting Tab When you purchase Blu ray Video make sure it matches your drive otherwise it will not play properly To playback video on an external display or TV using TOSHIBA Blu ray Disc Player use output devices like external displays or TV that have HDCP supported HDMI port The video cannot be displayed on an external display or TV connected to the RGB connector The Blu ray Disc movie can be played only on internal LCD displays or external devices connected via an HDMI output In Clone mode Dual View TOSHIBA Blu ray Disc Player may not function properly This product does not play HD DVD discs Blu ray d
104. lock In order to connect a security cable to the computer follow the steps as detailed below 1 Turn the computer so its right side faces you 2 Align the security cable with the lock slot and secure it in place Figure 4 10 Security lock Se 1 Security lock slot 2 Security lock Optional TOSHIBA Accessories You are able to add a number of options and accessories in order to make your computer even more powerful and convenient to use For reference the following list details some of the items that are available from your reseller or TOSHIBA dealer Universal AC Adaptor If you frequently use your computer at more than one site it may be convenient to purchase an additional AC adaptor to be kept at each site in order to remove the need to always carry the adaptor with you Sound System and Video mode This section describes some of the audio control functions Volume Mixer The Volume Mixer utility lets you control the audio volume for playback of devices and applications under Windows To launch the Volume Mixer utility right click on the speaker icon on the Windows Taskbar and then select Open Volume Mixer from the sub menu User s Manual 4 31 E To adjust the volume level of speakers or headphones move the Speakers slider m To adjust the volume level of an application that you are using move the slider for the corresponding application Microphone Level Follow the steps below to change the microp
105. m solving techniques In reality many problems can be solved simply but a few may require help from TOSHIBA Support if you find you need to consult others be prepared to describe the problem in as much detail as possible Preliminary checklist User s Manual You should always consider the simplest solution first the items detailed in this checklist are easy to fix and yet can cause what appears to be a serious problem m Make sure you turn on all peripheral devices before you turn on the computer this includes your printer and any other external device you are using H Before you attach an external device you should first turn the computer off then when you turn the computer back on again it will recognize the new device m Make sure all optional accessories are configured properly in the computer s setup program and that all required driver software has been loaded please refer to the documentation included with the optional accessories for further information on its installation and configuration Check all cables to ensure they are correctly and firmly attached to the computer loose cables can cause signal errors Inspect all connecting cables for loose wires and all connectors for loose pins Check that your disc media is correctly loaded Always try to make detailed notes of your observations and keep them ina permanent error log this will help you to describe your problems to TOSHIBA Support In addition if a pr
106. m that suddenly freezes all operations chances are the program has stopped responding You can exit the failed program without shutting down the operating system or closing other programs To close a program that has stopped responding 1 Press CTRL ALT and DEL simultaneously once then click Start Task Manager The Windows Task Manager window appears 2 Click the Applications tab If a program has stopped responding the words not responding appear beside its name in the list 3 Select the program you want to close then click End Task Closing the failed program should allow you to continue working If it does not continue with the next step 4 Close the remaining programs one by one by selecting the program name then End Task Closing all programs should allow you to continue working If it does not power off your computer and then restart it The computer will not start Make sure you attached the AC adaptor and power cord cable properly If you are using the AC adaptor check that the wall outlet is working by plugging in another device such as a lamp Verify that the computer is on by looking at the Power indicator If the indicator is glowing the computer is on Also try turning the computer off and then on If you are using an AC adaptor verify that the computer is receiving power from the external power source by looking at the DC IN Battery indicator If the indicator is glowing the computer is connected t
107. may or may not have the same data protection laws or data protection levels as required by your home country or region Once enabled you may disable the TOSHIBA PC Health Monitor at any time by uninstalling the software via Uninstall a program in the Control Panel Doing so will automatically delete all collected information from the HDD SSD The TOSHIBA PC Health Monitor software does not extend or modify TOSHIBA s obligations under its standard limited warranty in any way TOSHIBA s standard limited warranty terms and limitations apply Starting the TOSHIBA PC Health Monitor T The TOSHIBA PC Health Monitor can be started using the following methods Click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt PC Health Monitor H Click the icon in the notification area then click the Enable PC Health Monitor message the first time you run the application and Run PC Health Monitor every time thereafter No matter which method is used the TOSHIBA PC Health Monitor explanation screen will be displayed Clicking Next will display the PC Health Monitor Software Notice amp Acceptance screen Please carefully read the information displayed Selecting ACCEPT and clicking OK will enable the program By enabling the TOSHIBA PC Health Monitor software you agree with these terms and conditions and to the use and sharing of the collected information Once the program is enabled the TOSHIBA PC Heal
108. mber of keys available on your keyboard will depend on which country region your computer is configured for with keyboards being available for numerous languages There are different types of keys specifically typewriter keys function keys soft keys Windows special keys and the keypad overlay AN Never remove the key caps on your keyboard Doing so could cause damage to the parts under the key caps Keyboard indicator The following figure shows the position of the CAPS LOCK indicator and NUM LOCK indicator which show the following conditions m When the CAPS LOCK indicator glows the keyboard will produce capitals when any letter is typed m When the NUM LOCK indicator glows the ten key allows you to enter numbers User s Manual 4 2 Figure 4 1 Keypad indicators 1 CAPS LOCK indicator 2 NUM LOCK indicator CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format NUM LOCK When the NUM LOCK indicator glows you can use the number keys on the keyboard for number entry Function Key User s Manual The function keys F1 F12 are the twelve keys at the top of your keyboard t vit ax 8 0 og Ke Pill gt gt ava Lo F 2 a F F5 F6 F1 F8 F Fo Fil F12 The programmed functions can be executed in either of the following two modes described E Special function mode All
109. mediately and let the computer dry completely in these circumstance you should get the computer inspected by an authorized service provider in order to assess the scope of any damage Clean the plastics of the computer using a slightly water dampened cloth You can clean the display screen by spraying a small amount of glass cleaner onto a soft clean cloth and then wiping the screen gently with the cloth Never spray cleaner directly onto the computer or let liquid run into any part of it Never use harsh or caustic chemical products to clean the computer Moving the computer User s Manual While the computer is designed for flexible day to day usage you should exercise a few simple precautions when moving it in order to help ensure trouble free operation Make sure all disk disc activity has ended before moving the computer E Turn off shut down the computer m Disconnect the AC adaptor and all peripherals before moving the computer mH Close the display panel Do not pick up the computer by its display panel Before carrying your computer shut it down disconnect the AC adaptor and allow it to cool down a failure to follow this instruction may result in minor heat injury H Be careful not to subject the computer to impact or shock a failure to follow this instruction could result in damage to computer computer failure or loss of data E Never transport your computer with any cards installed this may cause dam
110. methods m Turn OFF the computer while external devices are connected H Connect external devices after turning OFF of the computer If this function can not be still used change the setting to disable the function and stop using this function If Sleep and Charge function is enabled the computer s battery will discharge during hibernation or when the computer is turned off Connect the AC adaptor to the computer or disable the Sleep and Charge function Some external devices may not work when connected to a compatible port if the Sleep and Charge function is enabled Reconnect the external device after turning the computer ON If the external device still does not work connect device to an USB port that does not have the Sleep and Charge function or change to disable the Sleep and Charge function Problem Procedure The USB Wakeup When Sleep and Charge function is enabled the function does not USB WakeUp function does not work for ports work that support the Sleep and Charge function In that case use an USB port that does not have the USB Sleep and Charge function or change to disable Sleep and Charge function Sound system In addition to the information in this section please also refer to the documentation supplied with your audio device Problem Procedure No sound is heard Press the function keys to increase or decrease volume Check the software volume settings Please check to see if Mute is turn
111. mount of Video RAM available is dependent on the computer s system memory Click Start gt Control Panel gt Appearance and Personalization gt Display gt Adjust resolution The amount of Video RAM can be verified by clicking the Advanced settings button in the Screen Resolution window Memory module The memory module is installed in the computer Legal Footnote Memory Main System For more information regarding Memory Main System please refer to the Legal Footnotes section User s Manual 3 11 Graphics Processing Graphics processing unit GPU performance Unit may vary depending on product model design configuration applications power management settings and features utilized GPU performance is only optimized when operating in AC power mode and may decrease considerably when operating in battery power mode Legal Footnote Graphics Processing Unit GPU For more information regarding Graphics Processing Unit GPU please refer to the Legal Footnotes section Intel Display Power Saving Technology User s Manual Intel GPU models may include the Display Power Saving Technology feature that can save the computer s power consumption by optimizing picture contrast on the internal LCD This feature can be used if the computer is running under battery mode H using the internal LCD display only The Display Power Saving Technology feature is enabled as the factory default If you want to disable t
112. n Hi Speed Start Mode there are some limitations on the settings at BIOS Setup If it is required to use BIOS Setup please do not use Hi Speed Start Mode Please execute BIOS Setup after Windows shut down Before using Hi Speed Start Mode please finish all the running programs E fyou set the boot up certification single sign on on the model featured with a fingerprint authentication a fingerprint or password is required again at the login phase TOSHIBA The TOSHIBA Accessibility utility provides Accessibility support to movement impaired users when they need to use the function keys In use the utility allows you to make the FN key sticky that is you can press it once release it and they press one of the function keys in order to access its specific function When set the FN key will remain active until another key is pressed Bluetooth Stack for This software enables communication between Windows by Toshiba the computer and external Bluetooth devices such as printers and mobile phones Bluetooth functions cannot be used in models that do not have a Bluetooth module installed User s Manual 5 2 User s Manual TOSHIBA eco Utility TOSHIBA Disc Creator TOSHIBA HDD SSD Alert Utility TOSHIBA Blu ray Disc Player TOSHIBA Sleep Utility This computer is equipped with eco mode This mode slightly lowers performance of some devices to reduce electric power consumption You can realize measurable power sav
113. n equipment checklist and basic information to start using your computer Some of the features described in this manual may not function properly if you use an operating system that was not pre installed by TOSHIBA Equipment checklist Carefully unpack your computer taking care to save the box and packaging materials for future use Hardware Check to make sure you have all the following items m TOSHIBA Portable Personal Computer AC adaptor and power cord 2 pin plug or 3 pin plug Documentation User Information Guide Instruction Manual for Safety and Comfort If any of the items are missing or damaged contact your dealer immediately Conventions This manual uses the following formats to describe identify and highlight terms and operating procedures Start The word Start refers to the button in Windows 7 Click m Tap the Touch Pad or click the left Touch Pad control button once m Left click the mouse once Tap the touch screen once only for touch screen models User s Manual 2 1 Right click Click the right Touch Pad control button once m Right click the mouse once Press and hold on the touch screen only for touch screen models Double click E Tap the Touch Pad or click the left Touch Pad control button twice E Left click the mouse twice m Tap the touch screen twice only for touch screen models HDD or Hard disk Some models are equipped with a Solid Sta
114. nt edge of the disc tray to make sure there are no such objects before closing the drive 4 Press gently at the center of the disc until you feel it click into place The disc should lie below the top of the spindle flush with the spindle base 5 Push the center of the disc tray to close it Press gently until it locks into place User s Manual 4 7 AN If the disc is not seated properly when the disc tray is closed the disc might be damaged Also the disc tray might not open fully when you press the eject button Removing discs To remove the disc follow the steps as detailed below AN Do not press the eject button while the computer is accessing the optical disc drive Wait for the optical disc drive indicator to go out before you open the disc tray Also if the disc is spinning when you open the disc tray wait for it to stop before you remove it 1 To pop the disc tray partially open press the eject button Gently pull the disc tray out until it is fully opened AN When the disc tray pops open slightly wait a moment to make sure the disc has stopped spinning before pulling the disc tray fully open 2 The disc extends slightly over the sides of the disc tray so you can grasp it Gently lift out the disc 3 Push the center of the disc tray to close it Press gently until it locks into place How to remove disc when the disc tray will not open Pressing the eject button will not open the disc tray when the computer p
115. o a live external power source Hardware and system checklist This section discusses problems caused by your computer s hardware or attached peripherals Basic problems may occur in the following areas E Power m USB device m Keyboard E Sound system m Internal display panel m External monitor Hard Disk Drive E LAN Optical Disc Drive E Wireless LAN Memory Media Card Bluetooth E Pointing Device Power User s Manual When the computer is not plugged into an AC power outlet the battery pack is the primary power source Your computer also has Real Time Clock RTC function All of the power resources are interrelated with anyone having the ability to produce apparent power problems Overheating power down If the processor s temperature reaches an unacceptably high level with either setting the computer will automatically shut down to prevent any damage in this instance all unsaved data in memory will be lost Problem Procedure Computer shuts Leave the computer off until the it reaches room down automatically temperature If the computer has reached room temperature and it still does not start or if it starts but shuts down quickly contact TOSHIBA Support AC power If you have trouble turning on the computer with the AC adaptor connected you should check the status of the DC IN Battery indicator Please refer to the Power Condition Descriptions section for further information Problem AC adaptor do
116. o the Legal Footnotes section CPU The processor type varies depending on model To check which type of processor is included in your model open the TOSHIBA PC Diagnostic Tool by clicking Start gt All Programs gt TOSHIBA gt Support amp Recovery gt PC Diagnostic Tool Legal Footnote CPU For more information regarding CPU please refer to the Legal Footnotes section User s Manual 3 10 Hard Disk Drive or The capacity of the hard disk drive varies Solid State Drive depending on the model To check which type of HDD SSD is included in your model open the TOSHIBA PC Diagnostic Tool by clicking Start gt All Programs gt TOSHIBA gt Support amp Recovery gt PC Diagnostic Tool Please note that part of the hard disk s overall capacity is reserved as administration space y E n this manual the word HDD or Hard disk drive also refers to the SSD unless otherwise stated E SSD is a large capacity storage media which uses Solid State Memory in place of a magnetic disk of the hard disk Under certain unusual conditions of prolonged non use and or exposure to high temperatures the SSD may be vulnerable to data retention errors Legal Footnote Hard Disk Drive HDD Capacity For more information regarding Hard Disk Drive HDD Capacity please refer to the Legal Footnotes section Video RAM The memory in a computer s graphics adaptor used to store the image displayed on a bitmap display The a
117. oblem recurs the log you have made will help to identify the problem faster Analyzing the problem User s Manual Sometimes the computer will give you clues that can help you identify why it is malfunctioning In view of this you should keep the following questions in mind Which part of the computer is not operating properly keyboard Hard Disk Drive display panel Touch Pad Touch Pad control buttons as each device will produce different symptoms Check the options within the operating system to ensure that its configuration is set properly What appears on the display Does it display any messages or random characters Make a screenshot of the current display and if possible look up the messages in the documentation included with the computer software or operating system Check that all connecting cables are correctly and firmly attached as loose cables can cause erroneous or intermittent signals Do any indicators light if so which ones what color are they and do they stay on or blink Write down what you see Do you hear any beeps if so how many are they long or short and are they high pitched or low pitched In addition is the computer making any unusual noises Write down what you hear Record your observations so you can describe them in detail to TOSHIBA Support Software The problems may be caused by your software or disk If you cannot load a software package the media may be damaged or the program might
118. off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver E Connect the equipment into an outlet on a circuit different from that to which the receiver is connected m Consult the dealer or an experienced radio TV technician for help Only peripherals complying with the FCC class B limits may be attached to this equipment Operation with non compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception Shielded cables must be used between the external devices and the computer s External RGB monitor port Universal Serial Bus USB 2 0 and 3 0 ports HDMI port and Headphone Microphone combo jack Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user s authority to operate the equipment FCC conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Contact Address TOSHIBA America Information Systems Inc 9740 Irvine Boulevard Irvine California 92618 1697 Telephone 949 583 3000 This information i
119. ollowing folder and then double click SVPWUTIL exe C Program Files TOSHIBA Utilities This utility lets you do the following m Register or delete the Supervisor Password H Specify restrictions for general users Starting the computer using a password i If you have already registered a user password there is one way to start the computer H Enter the password manually The password is necessary only if the computer was shut down in Hibernation mode or boot mode It is not needed in Sleep mode and Restart To enter a password manually follow the steps as detailed below 1 Turn on the power as described in the Getting Started section The following message will appear in the screen Password At this point the function keys do not work They will function after you enter the password 2 Enter the Password 3 Press ENTER If you enter the password incorrectly three times in a row or if you don t enter the password within 1 minute the computer shuts off In this case some features that can power on the computer automatically Wake up on LAN Task Scheduler etc may not work You must turn the computer back on to retry password entry TOSHIBA HWSetup i User s Manual TOSHIBA HWSetup is the TOSHIBA configuration management tool available through the Windows operating system To run TOSHIBA HWSetup click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt HWSetup The TOSHIBA
120. omatic Hibernation Mode The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid In order to define these settings you can follow the steps as described below 1 Click Start gt Control Panel gt System and Security gt Power Options 2 Click Choose what the power button does or Choose what closing the lid does 3 Enable the desired Hibernation Mode settings for When I press the power button and When I close the lid 4 Click the Save changes button Data save in Hibernation Mode When you turn off the power in Hibernation Mode the computer will take a moment to save the current data in memory to the Hard Disk Drive After you turn off the computer and the content of memory has been saved to the Hard Disk Drive turn off the power to any peripheral devices Do not turn the computer or devices back on immediately Wait a moment to let all capacitors fully discharge Chapter 3 The Grand Tour This chapter identifies the various components of the computer it is recommended that you become familiar with each before you operate the computer Legal Footnote Non applicable Icons For more information regarding Non applicable Icons please refer to the Legal Footnotes section l Please handle your computer carefully to avoid scratching or damaging the surface Front with the display closed The following figure shows the front of the computer with t
121. on of TOSHIBA Disc Creator in order to copy DVD Video or DVD ROM material that has copyright protection m DVD RAM discs cannot be backed up using the Disc Backup function of TOSHIBA Disc Creator You cannot back up CD ROM CD R or CD RW media to DVD R DVD R DL or DVD RW media using the Disc Backup function of TOSHIBA Disc Creator m You cannot back up CD ROM CD R or CD RW media to DVD R DVD R DL or DVD RW media using the Disc Backup function of TOSHIBA Disc Creator You cannot back up DVD ROM DVD Video DVD R DVD R DL DVD RW DVD R DVD R DL or DVD RW to CD R or CD RW media using the Disc Backup function of TOSHIBA Disc Creator H TOSHIBA Disc Creator cannot record in packet format E You might not be able to use the Disc Backup function of TOSHIBA Disc Creator to back up a DVD R DVD R DL DVD RW DVD R DVD R DL or DVD RW disc that was made with other software on a different optical media recorder m If you add data to a DVD R DVD R DL DVD R or DVD R DL disc that you have already recorded to you might not be able to read the added data under some circumstances For example it cannot be read under 16 bit operating systems such as Windows 98SE and Windows Me while in Windows NT4 you will need Service Pack 6 or later and in Windows 2000 you will need Service Pack 2 In addition to this some DVD ROM and DVD ROM CD R RW drives cannot read this added data regardless of the operating system m TOSHIBA Disc Creator
122. on the configuration of your computer one or all of the antennas listed below are built in m Wireless LAN Wireless LAN Bluetooth Legal Footnote Wireless LAN For more information regarding Wireless LAN please refer to the Legal Footnotes section User s Manual 3 8 Display screen Legal Footnote LCD 39 6cm 15 6 LCD screen may be configured with the following resolution depending on the model you purchased HD 1366 horizontal x 768 vertical pixels E FHD 1920 horizontal x 1080 vertical pixels Please be aware that when the computer is operating on the AC adaptor the image displayed on the internal screen will be somewhat brighter than when it operates on battery power This difference in brightness levels is intended to save power when operating on batteries For more information regarding LCD please refer to the Legal Footnotes section Stereo speakers Display hinges O Power button Power indicator Keyboard Touch Pad User s Manual The speakers emit sound generated by your software as well as audio alarms such as low battery condition generated by the system The display hinges allow the display panel to be positioned at a variety of easy to view angles Press this button to turn the computer s power on or off The Power indicator glows white when the computer is turned on However if you turn the computer off into Sleep Mode this indicator will blink white Your comput
123. onfigure the partitions on your Hard Disk Drive you may find that it becomes impossible to setup your computer e Make sure that the AC adaptor is connected during the restoring process When you reinstall the Windows operating system the hard disk may be reformatted and all data may be lost Turn off your computer 2 While holding down 0 zero key on the keyboard turn on your computer 3 Follow the on screen instructions to finish the recovery User s Manual 5 15 Chapter 6 Troubleshooting TOSHIBA has designed this computer for durability however should problems occur you are able to use the procedures detailed in this chapter to help determine the cause All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place Problem solving process Resolving problems will be much easier if you observe the following guidelines H Stop immediately when you recognize a problem exists as taking further action may result in data loss or damage or you may destroy valuable problem related information that can help solve the problem m Observe what is happening write down what the system is doing and what actions you performed immediately before the problem occurred Make a screenshot of the current display Please also be aware that the questions and procedures described in this chapter are meant only as a guide they are not definitive proble
124. ower is off If the power is off you can open the disc tray by inserting a slender object about 20 mm such as a straightened paper clip into the manual eject hole near the eject button Figure 4 4 Manual release with the eject hole 1 Manual eject hole AN Turn off the power before you use the manual eject hole If the disc is spinning when you open the disc tray the disc could fly off the spindle and cause injury User s Manual 4 8 Writable discs This section describes the types of writable discs Check the specifications of your drive to see the types of discs it can write Use TOSHIBA Disc Creator to write compact discs CDs CD R discs can be written only once The recorded data cannot be erased or changed m CD RW discs including multi speed CD RW discs high speed CD RW discs and ultra speed CD RW discs can be recorded more than once DVDs m DVD R DVD R DVD R DL and DVD R DL discs can be written only once The recorded data cannot be erased or changed E DVD RW DVD RW and DVD RAM discs can be recorded more than once Blu ray discs E BD R BD R DL BD R TL and BD R QL discs can be written only once The recorded data cannot be erased or changed E BD RE BD RE DL and BD RE TL discs can be recorded more than once Writing discs A User s Manual TOSHIBA Disc Creator is provided as writing software with this computer This utility can be used to write data You can use the DVD Super Multi
125. ows you to use the function keys without pressing the FN key m Standard F1 F12 mode Allows you to use the function keys in combination with the FN key You can select the desired mode by clicking Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt HWSetup gt Keyboard Special Standard F1 Function function mode F12 mode F1 FN F1 Launches the help file supplied with the software F2 FN F2 Decreases the computer s display panel brightness in individual steps F3 FN F3 Increases the computer s display panel brightness in individual steps User s Manual Special Standard F1 function mode F12 mode F4 FN F4 F5 FN F5 F6 FN F6 F7 FN F7 F8 FN F8 F9 FN F9 F10 FN F10 F11 FN F11 F12 FN F12 FN 1 FN 1 FN 2 FN 2 FN Space FN Space FN Gazz FN em Flash Cards Function Changes the active display device To use a simultaneous mode you must set the resolution of the internal display panel to match the resolution of the external display device Enables or disables the Touch Pad Moves media backward Plays or pauses media playback Moves media forward Decreases the computer s volume Increases the computer s volume Turns the sound on or off Switches the active wireless devices Reduces the icon size on the desktop or the font sizes within one of the supported application windows Enlarges the icon size on the desktop or the font sizes within one of
126. pes use recharging methods and handling Battery pack When the AC adaptor is not connected the computer s main power source is this lithium ion battery pack also referred to in this manual as the main battery Real Time Clock RTC function The Real Time Clock RTC function is supported The main battery provides power for the internal real time clock and calendar function and also maintains the system configuration while the computer is turned off If the RTC lasting time completely runs out the system will lose this information and the real time clock and calendar will stop working You can change the Real Time Clock settings in the BIOS setup utility Please refer to Troubleshooting for further information Care and use of the battery pack A This section provides the important safety precautions in order to handle your battery pack properly Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions Charge the battery pack only in an ambient temperature between 5 and 35 degrees Celsius Otherwise the electrolyte solution might leak battery pack performance might deteriorate and the battery life might be shortened Charging the batteries User s Manual When the power in the battery pack becomes low the DC IN Battery indicator will flash amber to indicate that only a few minutes of battery power remain If you continue to use the computer while the DC IN Batt
127. ptions Real Time Clock Problem The BIOS setting and system date time are lost Keyboard Procedure The lasting time of the Real Time Clock RTC has run out you will need to set the date and time in the BIOS setup utility by using the following steps 1 Click Start Point to the arrow i beside the Shut down button and then select Restart 2 Hold down the F2 key and then release this key one second after the computer is power on the BIOS setup utility will load 3 Set the date in the System Date field Set the time in the System Time field 5 Press F10 a confirmation message will be displayed 6 Select Yes the BIOS setup utility will end and the computer will restart gt Keyboard problems can be caused by the setup and configuration of the computer please refer to the The Keyboard section for further information Problem Output to screen is garbled Procedure Please refer to your software s documentation to ensure that it is not remapping the keyboard in any way remapping involves changing or reassigning the function of each key If you are still unable to use the keyboard you should contact TOSHIBA Support Internal display panel User s Manual Apparent computer s display panel problems may be related to the computer s setup and configuration Problem No display Procedure Press the function keys to adjust the display priority and to make sure it is not set for out
128. put to an external monitor Problem Markings appear on the computer s display panel Hard Disk Drive Problem Computer does not boot from Hard Disk Drive Slow performance Optical Disc Drive Procedure These marks may have come from contact with the keyboard and Touch Pad while the display panel has been closed You should try to remove the marks by gently wiping the display panel with a clean dry cloth or if this fails with a good quality LCD screen cleaner In this latter instance you should always follow the instructions with the screen cleaner and always ensure you let the display panel dry properly before closing it Procedure Check to see whether there is a disc in the optical disc drive if so remove it and try to start the computer again If this has no effect check the Boot Setting within the TOSHIBA HWSetup The files on the Hard Disk Drive may be fragmented in this instance you should run the disk Defragmentation utility to check the condition of your files and the Hard Disk Drive Please refer to the operating system s documentation or online Help File for further information on operating and using the Defragmentation utility As a last resort you should reformat the Hard Disk Drive and then reload the operating system and all other files and data If you are still unable to resolve the problem contact TOSHIBA Support For further information please refer to Operating Basics User s Manu
129. r AC adaptor near a heat source such as an electric blanket or heater m Never cover or block the air vents including those located at the base of the computer m Always operate your computer on a hard flat surface Using your computer on a carpet or other soft material can block the vents m Always provide sufficient space around the computer Overheating your computer or AC adaptor could cause system failure computer or AC adaptor damage or a fire possibly resulting in serious injury Creating a computer friendly environment Place the computer on a flat surface that is large enough for the computer and any other items you are using such as a printer Leave enough space around the computer and other equipment to provide adequate ventilation Otherwise they may overheat To keep your computer in prime operating condition protect your work area from Dust moisture and direct sunlight E Equipment that generates a strong electromagnetic field such as stereo speakers other than speakers that are connected to the computer or speakerphones H Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters m Extreme heat cold or humidity Liquids and corrosive chemicals Stress injury User s Manual Carefully read the nstruction Manual for Safety and Comfort It contains information on the prevention of stress injuries to your hands and wrists that can be
130. r you want to operate from AC power It is also the fastest way to get started because the battery pack will need to be charged before you can operate from battery power The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz enabling you to use this computer in almost any country region The adaptor converts AC power to DC power and reduces the voltage supplied to this computer Always use the TOSHIBA AC adaptor that was included with your computer or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor Never plug the AC adaptor into a power source that does not correspond to both the voltage and the frequency specified on the regulatory label of the unit Failure to do so could result in a fire or electric shock possibly resulting in serious injury Always use or purchase power cables that comply with the legal voltage and frequency specifications and requirements in the country of use Failure to do so could result in a fire or electric shock possibly resulting in serious injury The supplied power cord conforms to safety rules and regulations in the region the computer is bought and should not be used outside this region
131. radio equipment of low power data communication system radio station stipulated in the Telecommunications Business Law of Japan Intel Centrino Wireless N 7265 Wireless LAN and Bluetooth The Name of the radio equipment 7265NGWBN DSP Research Inc Approval Number D140017003 Intel Centrino Wireless N 7260 Wireless LAN and Bluetooth The Name of the radio equipment 7260NGWBN DSP Research Inc Approval Number D130021003 Intel Centrino Wireless AC 3160 Wireless LAN and Bluetooth The Name of the radio equipment 3160NGW DSP Research Inc Approval Number D130092003 Atheros QCNFA335 Wireless Network Adapter b g n and Bluetooth The Name of the radio equipment QONFA335 DSP Research Inc Approval Number D130158003 Broadcom BCM43142 Wireless Network Adapter b g n and Bluetooth The Name of the radio equipment BCM43142 DSP Research Inc Approval Number D135106201 Atheros QCNFA125 Wireless Network Adapter b g n The Name of the radio equipment QONFA125 DSP Research Inc Approval Number D140030003 The following restrictions apply Do not disassemble or modify the device Do not install the embedded wireless module into other device Radio approvals for wireless devices This equipment is approved to the radio standard by the countries regions in the following table User s Manual A Legal Footnotes If you use this equipment in the countries regions which are not listed in the table blow please
132. rm as distributed in the original archive If you are unsure whether or not a particular file is covered by this license you must contact us to verify this The FreeType Project is copyright C 1996 2000 by David Turner Robert Wilhelm and Werner Lemberg All rights reserved except as specified below 1 No Warranty THE FREETYPE PROJECT IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT WILL ANY OF THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED BY THE USE OR THE INABILITY TO USE OF THE FREETYPE PROJECT 2 Redistribution This license grants a worldwide royalty free perpetual and irrevocable right and license to use execute perform compile display copy create derivative works of distribute and sublicense the FreeType Project in both source and object code forms and derivative works thereof for any purpose and to authorize others to exercise some or all of the rights granted herein subject to the following conditions E Redistribution of source code must retain this license file FTL TXT unaltered any additions deletions or changes to the original files must be clearly indicated in accompanying documentation The copyright notices of the unaltered original files must be preserved in all copies of source files H Redistribution in binary form must provide a discla
133. rnation Mode A User s Manual The Hibernation Mode feature saves the contents of memory to the Hard Disk Drive when the computer is turned off so that the next time it is turned on the previous state is restored Please note that the Hibernation Mode feature does not save the status of any peripheral devices connected to the computer Save your data While entering Hibernation Mode the computer saves the contents of memory to the Hard Disk Drive However for safety sake it is best to save your data manually Data will be lost if you disconnect the AC adaptor before the save is completed Do not switch to Hibernation Mode while transferring data to external media such as USB devices memory media or other external memory devices as data will be lost Benefits of Hibernation Mode The Hibernation Mode feature provides the following benefits Saves data to the Hard Disk Drive when the computer automatically shuts down because of a low battery condition You can return to your previous working environment immediately when you turn on the computer Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature Allows the use of the panel power off feature Starting Hibernation Mode To enter Hibernation Mode click Start point to the arrow i beside the Shut down button and then select Hibernate from the menu User s Manual Aut
134. s only applicable for the countries regions where it is required EU Declaration of Conformity This product is carrying the CE Mark in accordance with the related European Directives Responsible for CE Marking is TOSHIBA EUROPE GMBH Hammfelddamm 8 41460 Neuss Germany The complete and official EU Declaration of Conformity can be found on TOSHIBA s web site http epps toshiba teg com on the Internet CE compliance This product is labeled with the CE Mark in accordance with the applicable European Directives notably RoHS Directive 2011 65 EU Radio Equipment and Telecommunications Terminal Directive 1999 5 EC Ecodesign Directive 2009 125 EC ErP and the related implementing measures User s Manual This product and the original options are designed to observe the related EMC Electromagnetic Compatibility and safety standards However TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented In this case the persons who have connected implemented those options cables have to provide assurance that the system PC plus options cables still fulfils the required standards To avoid general EMC problems the following guidance should be noted H Only CE marked options should be connected implemented m Only best shielded cables should be connected Working environment This product was designed to fulfil the EMC Electromagnet
135. s running on the computer and that power to the external Bluetooth device is turned on Check to ensure that no optional Bluetooth Adaptor is installed in the computer the built in Bluetooth hardware cannot operate simultaneously with another Bluetooth controller If you are still unable to resolve the problem contact TOSHIBA Support If you require any additional help using your computer or if you are having problems operating the computer you may need to contact TOSHIBA for additional technical assistance Before you call Some problems you experience may be related to software or the operating system so it is important that you investigate other sources of assistance first Before contacting TOSHIBA try the following Review troubleshooting sections in the documentation supplied with your software and or peripheral devices User s Manual E Ifa problem occurs when you are running software applications consult the software documentation for troubleshooting suggestions and consider calling the software company s technical support department for assistance m Consult the reseller or dealer from where you purchased your computer and or software they are your best resource for current information and support TOSHIBA technical support If you are still unable to solve the problem and suspect that it is hardware related visit TOSHIBA technical support website http www toshiba co jp worldwide User s Manual 6 15
136. s type of functionality Product Support The latest information regarding operating system support language support or available upgrades can be found on our web site http www toshiba europe com computers tnt bluetooth htm in Europe or www pcsupport toshiba com in the United States Radio Regulatory Information The Wireless device must be installed and used in strict accordance with the manufacturer s instructions as described in the user documentation that comes with the product This product complies with the following radio frequency and safety standards User s Manual 7 8 Europe Restrictions for Use of 2400 0 2483 5MHz Frequencies in Europe France Italy Luxembourg Norway Russian Federation Outdoor use limited to 10mW e i r p within the band 2454 2483 5MHz Implemented Implemented Military Radiolocation use Refarming of the 2 4GHz band has been ongoing in recent years to allow current relaxed regulation Full implementation planned 2012 For private use a general authorization is required if WAS RLAN s are used outside own premises For public use a general authorization is required General authorization required for network and service supply This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny Alesund Only for indoor applications Restrictions for Use of 5150 5350MHz Frequencies in Europe Italy Luxembourg U
137. sage during periods of peak demand by shifting some power consumption to periods when demand is lower For instance in peak hours of power consumption such as in the daytime in the summer the power consumed from the AC power source is automatically stopped and the battery is used for PC operation The AC power can then be used to charge the battery during periods where power demand is reduced such as at night thereby reducing the load during peak periods To access the utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Peak Shift Control For more information please refer to the Help file The TOSHIBA PC Diagnostic Tool will display basic system configuration information and allow the functionality of some of the computer s built in hardware devices to be tested Hi Speed Start Mode can make the computer start up faster than it would start up after a system shutdown 7 E The efficient performance might not be expected with multiple user I accounts registered E Only startup from built in HDD SSD supports Hi Speed Start Mode E When system needs to be restarted because of Windows update drivers update or applications installation please Shut down or Restart accordingly If not those changes will not be reflected to the system properly with Hi Speed Start Mode E When setting password e g user password HDD password please enter it using keyboard E When the system is booting i
138. ser s Manual Implemented For private use a general authorization is required if WAS RLAN s are used outside own premises General authorization required for network and service supply Russian Limited Federation e i r p 100mW Permitted to use only for indoor applications closed industrial and warehouse areas and on board aircraft 1 Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight 2 Permitted to use for public wireless access local networks on board aircraft during a flight at the altitude not less than 3000m Restrictions for Use of 5470 5725MHz Frequencies in Europe Italy Luxembourg Implemented Russian Limited Federation For private use a general authorization is required if WAS RLAN s are used outside own premises General authorization required for network and service supply e i r p 100mW Permitted to use only for indoor applications closed industrial and warehouse areas and on board aircraft 1 Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight 2 Permitted to use for public wireless access local networks on board aircraft during a flight at the altitude not less than 3000m To remain in conformance with European spectrum usage laws for Wireless LAN operation the above 2 4GHz and
139. sociation Random Access Memory Red Green and Blue Radio Frequency Interference User s Manual ROM RTC S P DIF SD SDHC SDXC SDRAM SSD TFT URL USB WAN WQHD www Read Only Memory Real Time Clock Sony philips Digital Interface Format Secure Digital Secure Digital High Capacity Secure Digital Extended Capacity Synchronous Dynamic Random Access Memory Solid State Drive Thin film Transistor Uniform Resource Locator Universal Serial Bus Wide Area Network Wide Quad High Definition World Wide Web 7 20 Index User s Manual AC adaptor additional 4 31 connecting 2 3 DC IN 19V jack 3 3 ASCII characters 4 5 Battery extending life 4 22 monitoring capacity 4 21 save mode 5 5 Battery indicator Bluetooth Bluetooth Stack for Windows by Toshiba 5 2 Cleaning the computer 1 17 Cooling vents 3 4 3 6 3 10 DC IN indicator 3 2 DC IN Battery indicator 3 14 Display automatic power off 5 4 hinges 3 9 opening 2 4 screen 3 9 Documentation list 2 1 Dual Pointing Device Touch Pad 6 8 DVD Super Multi drive using writing Equipment checklist 2 1 External monitor problems 6 13 Graphics Processing Unit 3 12 Hard disk drive automatic power off 5 5 HDMI out port 3 5 HW Setup accessing window Keyboard function keys 4 3 Function keys F1 F12 4 3 Index 1 User s Manual problems 6 6 Windows special keys 4 5 LAN cable types 4 23 connecting 4 23
140. soft com This product includes software written by Tim Hudson tijn cryptsoft com Original SSLeay License Copyright C 1995 1998 Eric Young eay cryptsoft com All rights reserved This package is an SSL implementation written by Eric Young eay cryptsoft com The implementation was written so as to conform with Netscapes SSL This library is free for commercial and non commercial use as long as the following conditions are aheared to The following conditions apply to all code found in this distribution be it the RC4 RSA Ihash DES etc code not just the SSL code The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson tjh cryptsoft com Copyright remains Eric Young s and as such any Copyright notices in the code are not to be removed If this package is used in a product Eric Young should be given attribution as the author of the parts of the library used This can be in the form of a textual message at program startup or in documentation online or textual provided with the package Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the copyright notice this list of conditions and the following disclaimer 2 Redistributions in binary form must reproduce the above copyright notice this list of
141. te drive Drive SSD instead of a hard disk drive In this manual the word HDD or Hard disk drive also refers to the SSD unless otherwise stated Using your computer for the first time Be sure to read the enclosed Instruction Manual for Safety and Comfort for information on the safe and proper use of this computer It is intended to help you be more comfortable and productive while using a notebook computer By following the recommendations in it you may reduce your chance of developing a painful or disabling injury to your hand arms shoulders or neck T i User s Manual This section provides basic information to start using your computer It covers the following topics Connecting the AC adaptor Opening the display Turning on the power Initial setup Use a virus check program and make sure it is updated regularly Never format storage media without checking its content formatting destroys all stored data It is a good idea to periodically back up the internal Hard Disk Drive or other main storage device to external media General storage media is not durable or stable over long periods of time and under certain conditions may result in data loss Before you install a device or application save any data in memory to the Hard Disk Drive or other storage media Failure to do so may result in the loss of data Connecting the AC adaptor User s Manual Attach the AC adaptor when you need to charge the battery o
142. ted additions to the library and distribution If you are looking for support start in this list if you haven t found anything to help you in the documentation m freetype devel nongnu org Discusses bugs as well as engine internals design issues specific licenses porting etc Our home page can be found at http www freetype org ENERGY STAR Program D ENERGY STAR Your Computer model may be ENERGY STAR compliant If the model you purchased is compliant it is labeled with the ENERGY STAR logo on the computer and the following information applies TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency Your computer ships with the power management options preset to a configuration that will provide the most stable operating environment and optimum system performance for both AC power and battery modes To conserve energy your computer is set to enter the low power Sleep Mode which shuts down the system and display within 15 minutes of inactivity in AC power mode TOSHIBA recommends that you leave this and other energy saving features active so that your computer will operate at its maximum energy efficiency You can wake the computer from Sleep Mode by pressing the power button Your ENERGY STAR certified computer should be set by default to enter a low power sleep mode after a period of inactivity Simply touching the mouse
143. th Monitor screen is displayed and the program will begin monitoring system functions and collecting information A message will be displayed if any changes which may interfere with the operation of the program are detected Follow the instructions displayed on screen in the message System Recovery User s Manual There is a hidden partition allocated on the Hard Disk Drive for the System Recovery Options in the event of a problem You can also create recovery media and restore the system The following items will be described in this section E System Recovery Options H Creating Recovery Media m Restoring the pre installed software from your created Recovery Media E Restoring the pre installed software from the Recovery Hard Disk Drive System Recovery Options i The System Recovery Options feature is installed on the hard disk when shipped from the factory The System Recovery Options menu includes tools to repair startup problems run diagnostics or restore the system See the Windows Help and Support content for more information about Startup Repair The System Recovery Options can also be run manually to repair problems The procedure is as follows Follow the instructions shown on the on screen menu 1 Turn off the computer 2 While holding the F8 key turn on the computer 3 The Advanced Boot Options menu will be displayed Use the arrow keys to select Repair Your Computer and press ENTER 4 Follow th
144. the supported application windows Changes the display resolution Turns the keyboard backlight on or off This function is supported with some models Flash Cards makes it visual and easy to access and use the function keys Normally the cards are hidden from view To activate and use the Flash Cards follow the steps below E 1 Standard F1 F12 mode Press and hold the FN key Flash Cards will appear on top of the screen by default Press the function key or click the card associated with the desired function The selected card with available options will appear 3 Press the function key repeatedly to cycle through the available options and release the FN key when the desired option is selected You can also click the desired option E Special function mode 1 Press the function key repeatedly to cycle through the available options and release it when the desired option is selected For more information please refer to the TOSHIBA Flash Cards Help file To access this help click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Flash Cards In the Settings for Flash Cards window click the Help button Sticky key You can use the TOSHIBA Accessibility utility to make the FN key sticky that is you can press it once release it and then press a desired function key To start the TOSHIBA Accessibility utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Acc
145. urope AS approved Approved by the appropriate agency Canada China CSA approved CCC approved Information for Wireless Devices Wireless Technology Interoperability T The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum DSSS Orthogonal Frequency Division Multiplexing OFDM radio technology and is compliant to E The IEEE 802 11 Standard on Wireless LANs Revision a b g n b g n or Revision a b g n ac as defined and approved by the Institute of Electrical and Electronics Engineers Bluetooth Modules are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum FHSS radio technology and is compliant to H Bluetooth Specification depending on the model you purchased as defined and approved by the Bluetooth Special Interest Group E Logo certification with Bluetooth wireless technology as defined by the Bluetooth Special interest Group This Bluetooth product is not compatible with devices using Bluetooth Version 1 0B specifications The wireless devices have not completed verification of connection and operation with all devices which are using the Wireless LAN or Bluetooth radio technology Bluetooth and Wireless LAN devices operate within the same radio frequency range and may interfere with one another If you use Bluetooth User s Manual and Wireless LAN devices simultaneously you may occasionally experien
146. use within the home Any other use beyond that stipulated above including conversion to digital format alteration transfer of copied material and distribution on a network without the permission of the copyright owner is a violation of copyright or author s rights and is subject to civil damages or criminal action Please comply with copyright laws in making any reproduction from this manual Disclaimer This manual has been validated and reviewed for accuracy The instructions and descriptions it contains are accurate for your computer at the time of this manual s production However succeeding computers and manuals are subject to change without notice TOSHIBA assumes no liability for damages incurred directly or indirectly from errors omissions or discrepancies between the computer and the manual Trademarks Intel Intel SpeedStep Intel Core and Centrino are trademarks or registered trademarks of Intel Corporation AMD the AMD Arrow logo PowerPlay Vari Bright and combinations thereof are trademarks of Advanced Micro Devices Inc User s Manual 1 1 Windows Microsoft and Windows logo are registered trademarks of Microsoft Corporation The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by Toshiba Corporation and its affiliates is under license The terms HDMI and HDMI High Definition Multimedia Interface and the HDMI Logo are trademarks or registered tr
147. uter s intelligent power supply detects the battery s charge automatically calculates the remaining battery capacity and protects electronic components from abnormal conditions such as a voltage overload from the AC adaptor This can be specified in the Power Options This feature lets you configure the computer in order to save battery power This can be specified in the Power Options This feature automatically turns power to the computer off when the display panel is closed and turns it back on when the display panel is opened This can be specified in the Power Options When battery power is exhausted to the point that computer operation cannot be continued the system automatically enters Hibernation Mode and shuts itself down This can be specified in the Power Options If you have to interrupt your work you can use this feature to allow you to turn off power to the computer without exiting from your software Data is maintained in the computer s main memory so that when you next turn on the power you can continue working right where you left off Hibernation Mode This feature lets you turn off the power to the computer without exiting from your software The contents of main memory are automatically saved to the Hard Disk Drive so that when you next turn the power on again you can continue working right where you left off Refer to the Turning off the power section for more details USB Wakeup function This function r
148. ve the problem contact TOSHIBA Support Procedure Remove the USB device from the computer and then reconnect it to a free port in order to ensure it is firmly attached Ensure that any required USB device drivers are properly installed to achieve this you should refer to both the device documentation and the operating system documentation Sleep and Charge function For more information and settings please refer to the section User s Manual Problem cannot use the Sleep and Charge function The battery depletes quickly even when turned OFF the power of the computer External devices connected to the compatible ports do not work when connected to a compatible port Procedure Sleep and Charge function may be disabled Enable the Sleep and Charge function in the TOSHIBA HWSetup When there is a current overflow of the external device connected to the compatible port USB bus power DC5V supply may be stopped for safety reasons When this happens disconnect an external device if some external devices are connected After that turn the power of the computer ON OFF to restore the function If this function can not be still used even if only one external device is connected stop using the external device because its current is over the acceptable value of this computer Some external devices may not be able to use the Sleep and Charge function In this case please try one or more of the following
149. ys cell Battery pack 45Wh 4 about 3 5 days about 50 days cell Extending battery life LAN To maximize the life of your battery packs At least once a month disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges Before doing so follow the steps as detailed below 1 Turn off the computer s power 2 Disconnect the AC adaptor and turn on the computer s power if it does not turn on then go to Step 4 3 Operate the computer on battery power for five minutes If you find that the battery pack has at least five minutes of operating time continue operating until the battery pack is fully discharged however if the DC IN Battery indicator flashes or there is some other warning to indicate a low battery condition go to Step 4 4 Connect the AC adaptor to the DC IN 19V jack of the computer and to a wall outlet that is supplying power The DC IN Battery indicator should glow amber to indicate that the battery pack is being charged however in the event that DC IN Battery indicator does not glow this indicates that power is not being supplied check the connections for the AC adaptor and the power cord 5 Charge the battery pack until the DC IN Battery indicator glows white The computer has built in support for Ethernet LAN 10 megabits per second 10BASE T Fast Ethernet LAN 100 megabits per second 100BASE TX or Gigabit Ethernet LAN 1000 megabits per secon

Download Pdf Manuals

Related Search

Related Contents

Appliance Warranty & Manuals  INSTALLATION MANUAL MANUEL D'INSTALLATION  Datasheet SG4 BASE  湖周地区ごみ処理施設整備事業 運営委託契約書（案）  TDSHーBA 保管用  PINTURA PAVIMENTOS ACRÍLICA  Equip High Speed HDMI Cable with Ethernet, A/M to A/M  Purgador de Condensado BK 45, BK 45U  エコキュート  Samsung HT-DS1100 用户手册  

Copyright © All rights reserved. Failed to retrieve file