Operating Instructions Busch-Wächter® 6848 AGM - Busch
Contents
1. Icon Function X Switching during all brightness levels d Switching during advancing twilight C Switching during darkness IL Short time pulse 8 4 Auxiliary post operation 8 4 1 Operation with extension unit push button Aside from the movement detector being triggered by the infrared radiation in the detection range manual operation is possible via an extension unit push button For example when an exit is not within the detection range of the movement detector the extension unit push button can be used The lighting can there be switched on or off manually with the push button Fig 21 Operation with extension unit push button e When operating with an extension unit push button the lighting for the set operating mode is switched on Operating Instructions 1473 1 8104 18 Operating Instructions a Busch Wachter Remote control 9 Remote control 9 1 Control elements of the remote control 1 2 3 4 5 6 T Fig 22 Control elements No Function 1 Resetting the switch on brightness to the settings of the potentiometers on the Busch Watchdog Press the button for at least 1 second 2 The current brightness is set as switch on brightness Press the button for at least 1 second 3 Deactivation of presence simulation 4 Presence simulation activation Continuous light between twilight and 22 30 p m CET or 23 30 CEST Followed by movement detection 5 Light deactivation fo2. Fig 8 Preparing the installation 1 Remove the locking screw 1 if installed 2 Press in the clamps 2 5 on the sides of the housing with a suitable tool 6 Carefully remove the front of the device Operating Instructions 1473 1 8104 10 Operating Instructions Busch W chter Installation and electrical connection 6 2 4 Water drainage Fig 9 Opening the water drain Depending on where the device is installed the water drain may have to be opened e Todo this pierce the plastic membrane on the bottom of the device The installation is prepared Operating Instructions 1473 1 8104 11 Operating Instructions Busch W chter Installation and electrical connection 6 2 5 Mounting steps 1 an Lex Nev gor E TR Kaya OFF QO M O SE See Fig 10 Mounting the bottom of the device No Function 1 Potential separated 1 Mount the device to the wall 86 5 mm 8 5 mm Do not use countersunk head screws for mounting d NL to the wall N p4 Use screws with a head diameter of 6 5 mm 8 5 d wi mm 53 5 mm 3 9 mm 2 Connect the power to the device see section 6 3 gt Observe the maximum admissible cable cross 1 5 2 5 mm sections max 14 5 mm Operating Instructions 1473 1 8104 12 Operating Ins
3. Test mode is exited automatically after 10 minutes or by adjusting the brightness The activation test has been carried out Operating Instructions 1473 1 8104 16 Operating Instructions Busch Wachter Operation Control elements Fig 18 Control elements Operation No Function 1 LED e On continuous light set only possible with remote control Flashes fast detection in test mode e Flashes 3 times detection in standard and normal operation e Flickers incoming IR signals remote control 2 Lens 3 Trim potentiometer for switch off delay short time pulse 4 Trim potentiometer for brightness value test standard operation 5 Screw for dismantling safety 8 2 Standard operation O c T S Fig 19 Standard operation Lighting during advancing twilight remains switched on for 3 minutes after the last detection O After activating the mains supply voltage the device remains in test mode for 10 minutes see chapter Activation test Operating Instructions 1473 1 8104 Operating Instructions Busch Wachter Operation 8 3 Standard operation time and brightness dependent Go 20 46 O TL T S 10 sek Min Fig 20 Normal operation Set the values for the brightness limit value and the switch off delay on period of the light after the last detection Short time pulse for activating the staircase light timer switches or door bells
4. 1473 1 8104 Rev 01 11 2012 Operating Instructions Busch Wachter 6848 AGM 220 MasterLINE premium BUSCH JAEGER Ki Operating Instructions Busch Wachter 1 ER 3 2 Hee 3 3 EIN NIE Us ps sence te ce see sere sen ae see 3 A Setup and Ett er EE 4 4 1 Features of function ANd eoupment ernennen 4 4 2 Reie Rene re E E eco EEE Eee aries mate 5 4 2 1 Overview of the detection rangdes 5 4 2 1 1 Standard Coverage trt rEEEArEEEAEEEEAEEEEAEEEEAEEEEEEEEEEEEEESEEEES EEren EEn a reren 5 4 2 1 2 Coverage with eine DEE 5 4 2 2 Limitation of the detection range nennen 5 e Kieler Be EE 6 6 Installation and electrical connection nenn nano nnnn nenne nnnennnnnnnnnnnnennnennnnennnnonnnennnennnnennnennnnnnnne T 6 1 Requirements for the elechcan nennen T 6 2 Olaf lee al ME 8 6 2 1 MOUNUNG MIELNOGS nenn ee ne O einer 8 0 2 1 1 NAF MOUNN EE 8 6 2 1 2 Wall mounting with gradient 02 40024002000Ben0nnnnnnenenennnnnnennne nenn nnnnnnene nenn nnnnnnnnenennnnnnenenennnnenenennnnnen 9 921 3 Ceiling MOUNUNG BEE 9 6214 deg ug ei a E EE 9 6 2 2 IMS LA Le 10 6 2 3 Preparing Ihe Ml St AO DEE 10 6 2 4 Water drainage EE 11 6 2 5 MOUNTO SODS sasse E E ee E E re 12 6 3 Electrical CONNECHON ee ae een 14 6 3 1 Standard CONNECHOB een ee ee nn era ae Ee 14 6 3 2 Standard connection with external signal goeneraiors nennen nennen nenne nnennne nennen nnnnen 14 6 3 3 Standard connection with 2 circuit breakers per relay 10 A nennen nennen 1
5. 4 T ele tan SUNN E 15 7 1 Setting limiting the coverage and the detection ronde 15 7 2 Activation Test 16 8 e ee ee ee ee ee ee ee 17 8 1 Control elements ee ee ee ns een een 17 8 2 Standard ORE aO WEE 17 8 3 Standard operation time and brightness dependent nennen nennen 18 8 4 Auxiliary post operation nenn nenn nano nenn nenne nano nnnnnnnnonnnennnnnnnnennnennnennnnennnennnnnennnennnnnnnne 18 8 4 1 Operation with extension unit push button nennen 18 9 P le EE 19 9 1 Control elements of the remote Control 19 9 2 Technical data of the remote Control 19 9 3 Commissioning of remote Control 20 9 4 Battery change of remote Control 20 Operating Instructions 1473 1 8104 2 Operating Instructions A Fr 1 Safety Warning Electric voltage Risk of death and fire due to electrical voltage of 230 V Work on the 230V supply system may only be performed by authorised electricians Disconnect the mains power supply prior to installation and or disassembly 2 Intended use The device is to be used exclusively with the components that are supplied and licensed as described in chapter Setup and function 3 Environment Consider the protection of the environment Used electric and electronic devices must not be disposed of with domestic waste The device contains valuable raw materials which can be recycled Therefore dispose of the device at the appropriate collecting depot All packagi
6. cade adjacent live parts e Use suitable personal protective clothing e Use only suitable tools and measuring devices e Check the supply network type TN system IT system TT system to secure the following power supply conditions classic connection to ground protective earthing necessary additional measures etc Operating Instructions 1473 1 8104 Operating Instructions Busch Wachter Installation and electrical connection 6 2 Mounting Warning Electric voltage Risk of death and fire due to electrical voltage of 230 V Work on the 230V supply system may only be performed by authorised electricians Disconnect the mains power supply prior to installation and or disassembly Caution Risk of damaging the device The lens of the device is sensitive and can easily sustain damage Do not press on the lens when opening or closing the device 6 2 1 Mounting methods There are four methods of mounting the Busch Watchdog MasterLINE range The mounting hole is compatible with all previously available Busch Watchdog models The possible mounting methods are described in the following O Note The adapters for the following mounting methods must be ordered separately Wall mounting with gradient Ceiling mounting for the desired position Corner adapter 6 2 1 1 Wall mounting Fig 3 Wall mounting Classic wall mounting Operating Instructions 1473 1 8104 8 Operat
7. e Do not press on the lens when setting the device Use the following steps to set the coverage and the detection range Gd Fig 14 Adjusting the lateral detection range 1 Adjust the lateral detection range by turning the head of the device Fig 15 Adjusting the coverage 2 Adjust the coverage by lifting or lowering the head of the device The minimum coverage is 6 m Operating Instructions 1473 1 8104 15 Operating Instructions Busch Wachter Commissioning IT Fig 16 Adjusting the detection range by masking 3 The range can be specifically limited by gluing on the enclosed foil Cut the enclosed foil to the size required The coverage and the detection range are set 7 2 Activation test The activation test can also be triggered via the service remote control see separate operating manual TE SO us O C T S 10 sek Min Fig 17 Control element To carry out the activation test perform the following steps 1 Set selector switch to T S The device is now in test mode for 10 minutes daytime operation switch off delay 2 sec In addition each detection is indicated by the status LED flashing quickly The device then switches back to standard operating mode 2 Tocarry out an additional activation test set the selector switch back to position T S or interrupt the operating voltage supply for more than 15 seconds The device is now in test mode for another 10 minutes
8. er out of the remote control 2 Insert a new battery of type 2025 The plus pole of the battery must be on top 3 Push the battery holder back into the device Operating Instructions 1473 1 8104 20 Operating Instructions Busch Wachter Remote control Operating Instructions 1473 1 8104 21 Operating Instructions Busch Wachter A member of the ABB Group Busch Jaeger Elektro GmbH PO box 58505 Ludenscheid Freisenbergstra e 2 58513 Ludenscheid Germany www BUSCH JAEGER com info bje de abb com Central sales service Phone 49 0 2351 956 1600 Fax 49 0 2351 956 1700 Notice We reserve the right to at all times make technical changes as well as changes to the contents of this document without prior notice The detailed specifications agreed to at the time of ordering apply to all orders ABB accepts no responsibility for possible errors or incompleteness in this document We reserve all rights to this document and the topics and illustrations contained therein The document and its contents or extracts thereof must not be reproduced transmitted or reused by third parties without prior written consent by ABB Copyright 2012 Busch Jaeger Elektro GmbH All rights reserved BUSCH JAEGER Sa 1473 1 8104 Rev 01 11 2012
9. he detection ranges 4 2 1 1 Standard coverage Fig 1 Coverage State of the device at the point of delivery is standard coverage Here zones R1 R2 are combined 4 2 1 2 Coverage with zone separation Fig 2 Coverage with zone separation For zone separation the following coverages are divided Setup and function ZONE Coverage R1 lt 15m R2 Maximum of 1m 4 2 2 Limitation of the detection range The horizontal detection range of the Busch Watchdog is 220 The detection range can be limited in case of special local circumstances To do this proceed as follows 1 Cut the included adhesive film to the desired length 2 Glue the section of covering foil from the front onto the area of the sensor of your Busch Watchdog where the detection is to be blocked out O Note For an illustration see chapter 7 1 on page 15 Operating Instructions 1473 1 8104 Operating Instructions Busch Wachter 5 Technical data Designation Nominal voltage Value 230 V AC 10 50 60 Hz Technical data Switching capacity 3680 W VA Maximum switching current 10 AX Maximum power loss lt 1W Horizontal detection e Busch Watchdog 220 220 Output zone 2 R2 AC 230 V AC 12 48 V AC DC maximum 10 AX 2300 W VA 10 mA 1A Twilight sensor 0 5 300 lux Switch off delay 10 seconds 30 minutes Short time pulse e Pulse duration e Pause ti
10. ing Instructions Busch Wachter Installation and electrical 6 2 1 2 Wall mounting with gradient Fig 4 Wall mounting with gradient connection Wall mounting with gradient is recommended on a building situated on a hill or with a gradient This allows the detection ranged to be used effectively 6 2 1 3 Ceiling mounting Fig 5 Ceiling mounting There are two options for ceiling mounting 1 From the bottom for a wider detection range 2 With a corner adapter which allows the device to be ideally positioned 6 2 1 4 Corner mounting Fig 6 Corner mounting The combination with a corner adapter is recommended for an optimal 280 detection range O Note Detailed user information is available via the link http www busch jaeger katalog de index php in the Busch Watchdog category under accessories Operating Instructions 1473 1 8104 Operating Instructions Busch Wachter Installation and electrical connection 6 2 2 Installation sites Fig 7 Installation sites a lc e Ceiling mounting in narrow rooms is not recommended e The mounting height of the device should be between 1 7 m and 2 5 m e The distance between light and movement detector should be at least 1 5 m e For optimum detection of persons the approach into the detection range should always be offset and never frontal 6 2 3 Preparing the installation To prepare the installation of the device perform the following steps
11. me e Pause time with continuous light presence simulation 1 second 9 seconds 55 seconds Coverage if mounted 2 5 m high Maximum of 16 m Operating temperature 25 C 55 C Protection type IP 55 O Information for the connection of ballasts Please observe the following points regarding high inrush currents for ballasts The ballast manufacturer s specification determines the possible number of ballasts Operating Instructions 1473 1 8104 nn EE ut A f am BU rh arhfc Cn VVa ci N LG 6 Installation and electrical connection Warning Electric voltage Risk of death due to electrical voltage of 230 V during short circuit in the low voltage line Low voltage and 230 V lines must not be installed together in a flush mounted socket 6 1 Requirements for the electrician Warning Electric voltage Install the device only if you have the necessary electrical engineering knowledge and experience e Incorrect installation endangers your life and that of the user of the electrical system e Incorrect installation can cause serious damage to property e g due to fire The minimum necessary expert knowledge and requirements for the installation are as follows e Apply the five safety rules DIN VDE 0105 EN 50110 1 2 3 4 5 Disconnect from power Secure against being re connected Ensure there is no voltage Connect to earth and short circuit Cover or barri
12. ng materials and devices bear the markings and test seals for proper disposal Always dispose of the packaging material and electric devices and their components via the authorized collecting depots and disposal companies The products meet the legal requirements in particular the laws governing electronic and electrical devices and the REACH ordinance EU Directive 2002 96 EC WEEE and 2002 95 EC RoHS EU REACH ordinance and law for the implementation of the ordinance EC No 1907 2006 Operating Instructions 1473 1 8104 3 Operating Instructions Busch Wachter Setup and function 4 Setup and function The Busch Watchdog 220 MasterLINE premium is a movement detector with a detection range of 220 and is suitable for use in the home The Busch Watchdogs are passive infrared movement detectors which switch loads via the KNX bus when sources of heat move within its detection range Busch Watchdog is not an intrusion or attack alarm 4 1 Features of function and equipment e 2 zone operation e Second switching output e Coverage of 16 meters e Additional floating switch contact e Display for detection and operation mode e Integrated twilight switch e Operation with IR remote control e Setting option e Creep zone protection and activation when exiting the door e Installation of a camera Operating Instructions 1473 1 8104 Operating Instructions Busch Wachter 4 2 Detection ranges 4 2 1 Overview of t
13. r 4 hours No detection of movement 6 Light activation for 4 hours No detection of movement 7 Resetting to automatic movement detection O The sensitivity of the movement sensors can be adjusted to surroundings which are particularly restless or free of movement 9 2 Technical data of the remote control Designation Value Operating voltage 3 V DC Battery type CR 2025 Battery life Approximately 2 years Coverage Maximum of 6 m Protection type IP 40 Operating temperature 0 C 45 C Operating Instructions 1473 1 8104 19 Operating Instructions Busch Wachter 9 3 Commissioning of remote control J i Fig 23 Removing the protective foil from the battery Remove the protective foil from the battery before commissioning Fig 24 Programming the remote control Remote control e Press the AUTO button on the remote control for at least 3 seconds within the period of 10 minutes after activating the power on the Busch Watchdog The Busch Watchdog must be de energized beforehand for at least 30 seconds The remote control will then automatically connect itself to the Busch Watchdog and the Busch Watchdog will flash if the reception is correct Repeat these steps to program a maximum of 9 additional remote controls 9 4 Battery change of remote control J p N Fig 25 Changing the battery 1 Pull the battery hold
14. tructions Busch Wachter Installation and electrical connection The bolting dimensions of the base may be compatible with existing bores on older versions of the Busch Watchdog Latch the upper part of the device onto the base 3 To protect the device against unauthorized opening the enclosed screw can be used on the bottom of the device To protect the device against unauthorized opening screw the enclosed screw into the bottom of the device Operating Instructions 1473 1 8104 13 Operating Instructions Busch Wachter Installation and electrical connection 6 3 Electrical connection 6 3 1 Standard connection Fig 11 Universal relay insert With 1 circuit breaker the maximum sum current of 10 A is admissible for both relays 6 3 2 Standard connection with external signal generators Fig 12 Universal relay insert with external signal generators O Note For more information see chapter Extension unit operation 8 4 on page 18 6 3 3 Standard connection with 2 circuit breakers per relay 10 A Fig 13 Universal relay insert with 2 circuit breakers With 2 circuit breakers per relay 10 A Operating Instructions 1473 1 8104 14 Operating Instructions Busch Wachter Commissioning T Commissioning 7 1 Setting limiting the coverage and the detection range Caution Risk of damaging the device The lens of the device is sensitive and can easily sustain damag
Download Pdf Manuals
Related Search