Sea Gull Lighting 49150BLE-962 Installation Guide
Contents
1. Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill In Item Number On Carton And File This Sheet For Fixture Reference ITEM INSTALLATION HC 937 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX CAUTION DO NOT BEND TABS THAT SECURE GLASS BENDING TABS WILL PREVENT THE GLASS FROM SITTING PROPERLY STEP 1 Using outlet box screws not supplied fasten mounting bar D to outlet box through slots in mounting bar D STEP 2 Thread nut E onto nipple F so that 5 threads are exposed above nut E Thread that end of the nipple F into mounting bar D and tighten nut E against mounting bar D STEP 3 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK CI PARALLEL WIRE ROUND amp SMOOTH f PARALLEL WIRE SQUARE amp RIDGED O O O COSI NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart WHITE B Take your fixture wire s from group A and place evenly against the black wire from the outlet box Do Not twist wires together before using2. plate A over nipple F and secure in place with cap nut H STEP 2 Install lamps STEP 3 Slide the edge of diffuser I into backplate lip G making sure it securely fits in there CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts BALLAST REPLACEMENT TURN POWER OFF Carefully remove glass by the following glass installation instructions in reverse Separate the 120v connection of the ballast from the supply wire by removing wire nuts Disconnect the secondary ballast wires to the socket by inserting a small screwdriver into the rear of the socket release the wire lead Remove ballast mounting screws and remove ballast from fixture assembly Replace ballast with the same model secure ballast to fixture assembly insert secondary ballast wires by pushing them into the rear of the socket and make proper wiring connections to the supply wire
3. INSTALLATION AND SAFETY INSTRUCTIONS FOR YOUR SAFETY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER OFF GENERAL You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician NOTE Proper wiring is essential for the safe operation of this fixture OUTLET BOX WIRE CONNECTORS MOUNTING BAR D NOT SUPPLIED NY NUT E m ZG PAA rx _ SCREW G SNIPPLE F I mP OUTLET BOX 4 SCREWS MOUNTING BAR D WIRE CONNECTORS GROUND WIRE NOT INCLUDED FIGURE 2 Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture NOTE FOR FIXTURES PROVIDED WITH 75 C OR 90 C SUPPLY WIRE WARNING ONLY THESE WARNINGS ARE PROVIDED ON THE U L LABEL AND ON THE FIXTURE CARTON RISK OF FIRE MOST DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED 60 C CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING DIFFUSER I OUTLET BOX SCREWS NIPPLE F lt _ BACKPLATE LIP G BACKPLATE A CAP NUT H FIG 1 SB guli lighting Installation And Safety Instruction HC 937 102005
4. wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 4 GROUNDING INSTRUCTIONS The green grounding screw G is to be inserted into the hole with two raised dimples provided on the mounting bar D Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw G on the mount ing bar D If uninsulated ground wire is on the universal mounting bar connect the ground wire from the fixture if supplied and the out let box to it using a small wire connector not supplied See Figure 2 NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manu factured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside the outlet box Position back
Download Pdf Manuals
Related Search