Windster WS-38 User's Manual
Contents
1. P 21 A inia P 22 WARNING Due to sharp edge please wear Safety Workman Gloves for installation cleaning light bulb changing and dismantling to reduce the risk of any bodily injuries Safety Workman Gloves S E A Important Safety Insturctions Read and Save These Instructions CAUTION To reduce risk of fire and to properly exhaust air make sure to properly exhaust air Be sure to duct air outside Do not vent exhaust air into spaces within walls ceilings attics crawl spaces or garages WARNING To reduce the risk of fire or electric shock do not use this fan with any solid state speed control device WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY OBSERVE THE FOLLOWING A Use this unit only in the manner intended by the manufacturer If you have questions contact the manufacturer B Before servicing or cleaning the unit switch power off at service panel to prevent power from being switched on accidentally C When the service disconnecting means cannot blocked securely fasten prominent warning device such as a tag to service panel CAUTION For general ventilating use only Do not use to exhaust hazardous or explosive materials and vapours WARNING TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE A Never leave surface units unattended at high settings Boil over cause smoking and greasy spillovers that may ignite Heat oils slowly on low or medium s2. 3 Lift up the Baffle filter 4 Pick up the inner oil collector NOTE Reinstalling Baffle filters Reverse the steps as removing Baffle filters For mounting under cabinet 1 After above step H then continue the following steps 2 Remove 2 screws on the spacer s 3 Remove spacer s 4 Key hole to mount to under cabinet Key hole I Maintenance Instruction 1 Maintenance shall be important than repair Please take care of the needed maintenance in order to secure and extend the excellent functions and using life Note Before repairing the range hood Disconnect the power source 2 After using the machine wipes the machine by neutral detergent in order to keep it clean and maintain the appearance with brightness and sanitation 3 When the level of dirty oil of the collector reached 4 5 of height it has to be removed in order to avoid overflowing and pollution J Ducting This style of range must be vented via ducting to the outside of the house Follow general rules when ducting the hood Use correct size of ducting 6 or 7 round do not reduce size of ducting make all turns gradual no short corners If ducting ran will be longer than 10 feet enlarge duct by at least 1 inch diameter after each 10 feet Tape all joints in ducting and all gasketed openings on hood for a tight seal For round ducting from the top Loosen 2 screws Ref 1 fit the gr
3. Main power button NOTE ALL FUNCTIONS CAN BEWORKED ONLY UNDER THE MAIN POWER IS ON A By pressing 5 all functions are stand by B By pressing again all functions will be turned off H 2 Use for Fan eo eee orr Fan speed selection and fan off A Fan ON When the main power button is being pressed by pressing button e ee eee for desired fan speed e slow speed ee medium speed ee e high speed B Fan OFF To turn off the fan just press the orr button or press off the b main power button NOTE a Thefan speed can be interchanged by pressing any one of above 3 buttons however b NEVER PRESS ANY OF TWO BUTTONS INATIME 3 Use for Light NOTE MAKE SURE THE MAIN POWER BUTTON IS PRESSED BEFORE TURNING ON THE LED LIGHT A Press X to turn on the LED light B Press X again tor turn off the LED light 4 Use for Auto sensor LED night light NOTE MAKE SURE THE MAIN POWER BUTTON IS PRESSED BEFORE TURNING ON THE LED LIGHT A The auto sensor of LED night light will be automatically turn on at 2096 brightness compare to original when the surroundings is getting darker or dark B When the surroundings is getting brighter or bright the auto sensor will turn the night light off automatically C To turn off the auto sensor night light button after cooking turns off the main power button To keep this function remain the main pow
4. to be continued C Use slotted screw driver or whatever flat head to knock out the pre mounted rear rectangular cap 43 L Rear Rectangular Ducting F Take the pre mounted G Mount the rectangular rectangular plate plate previous removed on top of transition plate NOTE An optional kit for rear rectangular ducting Transition plate Rectangular starting collar ER H Insert appropriate rectangular starting collar optional 2 different size 114 x 34 x 1 LxWxH 1174 x 3 x 38 LxWxH gt or Smal Mount rectangular J Rectangular starting collar starting collar 11 x 34 x 3 LxWxH 11 x3 x 1 optional optional m M Mounting Range Hood To Cabinet NOTE Read Remove and Reinstall Baffle filter amp For mounting under cabinet on page 8 1 Position the hood in place so that a The electrical line is routed through the appropriate Knockout opening This step will have to be accomplished while positioning the hood Fig 10 b The large part of the keyhole mounting slots on the hood fit onto the hood mounting screws projecting from the bottom of the cabinet Fig 11 2 Adjust the hood so the front is flush with the cabinet front 3 Tighten the hood
5. on 42 48 quantity may be varied U Circuit Diagram NOTE Any faults with this unit should only be attended to by a qualified technician NIGHT LIGHT p OOO0 O O HI D e ee eee OFF Cx AC DC POWER SUPPLY UNIT Voltage 110V 60Hz Power consumption maxi 170W Motor LED light 8 3 8 WINDSTER Limited Warranty Windster Hoods Inc warrants this product against defects in material or workmanship as follows I 2 Labor For a period of one 1 year from the date of purchase if this product is determined to be defective Windster will repair or replace the product at its option at no charge After the warranty period you must pay for all labor charges During the labor warranty period there will be no charge for labor Parts In addition Windster will supply at no charge new or rebuilt replacements in exchange for defective parts for a period of two 2 years After the warranty period you must pay for all parts costs During the parts warranty period there will be no charge for parts You must carry in or mail in your product during the warranty period This warranty only applies to products purchased and serviced in the United States or Canada What Is Not Covered By These Warranties 1 Conditions and damages resulting from any of the following 2 3 Improper installation delivery or maintena
6. WINDSTeR MODEL WS 38 series OPERATION MANUAL Please read and save this guide through before using your range hood Store the guide away in a safe place so that you will know where it is when you want to refer to it Table of Contents A Important Safety Instructions P 1 B Safety Notes P 3 C Tools and Materials Required P 4 D Accessory Package P 4 E Preparing the Range Hood Pu F Preparing the Installation Location P 6 G Providing Electrical Power Eu H Remove and Reinstall Baffle filters P 8 Maintenance Instruction Feo J IN St P 9 K Vertical Rectangular Ducting P 10 L Rear Rectangular Ducting P 11 M Mounting Range Hood to Cabinet p 19 N Mounting Range Hood Without Cabinet P 14 P Making the Electrical Connection P 15 Q Use and Care MM Fl R Troubleshootings P 18 9 Replace The LED Light P 18 T Parts Layout Diagram P 19 U Circuit Diagram
7. ay plastic round collar 6 over the circular opening on top Ref 2 and fasten 2 screws included in order to provide a tight seal for ducting to attach to Ref 3 if you want to use 7 ducting take 7 converter included to join together with the 6 round collar Ref 4 LA Loosen s l Loosen 2 screws Fit 6 collar Fasten 2 screws Fit converter DP K Vertical Rectangular Ducting A Remove the pre mounted D Overlap the rectangular 6 round duct opening starting collar on the top of transition plate Half roundsection _ E Mounting rectangular starting B Put transition plate by first collar with remaining screws installing 4 screws on the half round section Optional F Completely finished NOTE An optional kit for vertical rectangular ducting Transition plate 4 Small C Take the rectangular starting Rectangular starting collar collar Optional 4m L Rear Rectangular Ducting P f E n f rs i i ive i a D Pre mounted A Remove the pre mounted 6 round duct opening rectangular plate B Puttransition plate by first installing 4 screws on E Remove the pre mounted the half round section rectangular plate Optional
8. ce Fig 4 F Preparing The Installation Location 1 If you want to move the electric range to make room for working on the cabinet turn off the 220 volt power for the electric range at the service entrance 2 Before moving a gas range shut off the gas NOTE SKIP FOLLOWING STEPS 3A THROUGH 3D IF THE HOOD IS TO BE MOUNTED ON A CABINET WITH A FLUSH BOTTOM 3 For installation onto a recessed bottom cabinet a Measure the space under the cabinet between the inside front edge and inside back edge Fig 5 With a saber saw cut two 1 x2 wood filler strips purchased locally to fill in the bottom of the cabinet b Start a 1 long wood screw purchased locally about 3 from each end of the 1 x2 wood strips Fig 6 c Position the strips on the cabinet bottom and screw the strips securely to the cabinet Fig 7 d For a more secure installation drill four 3 16 holes from inside the cabinet down into the wood filler strips Insert screws into the starter holes in cabinet and tighten screws until wood filler strips are secured under cabinet 4 Center the hood in place beneath the cabinet and flush with the front of the cabinet Mark the following a The six keyhole mounting slots for the hood Mark these onto the bottom of the cabinet or if the cabinet bottom is recessed Onto the wood strips Fig 7 b The electrical k
9. er button always ON H Range hood should be turn on either before or the same time when cooking begins After cooking range hood should be kept on for about 3 more minutes for complete ventilation of cooking odor Care Instruction Please always pull the plug out before cleaning or dismantling wear Safety gloves to reduce the risk of any injuries Exterior Can be cleaned with any type of non abrasive detergent anda clean cloth Green Pad or any metal type cleaning pad is not recommended for exterior As those may scratch the graphic wordings on control panel Interior 1 Switch ON the fan at High mix mild detergent with water in mist sprayer at fine spray mixture on to the blades for 60 seconds with the fan running mist sprayer is not included 2 Leave fan on for an additional 3 minutes to dry oil basin 3 Repeat on other turbine vane can be cleaned simultaneously with the first R Troubleshootings Symptom Correction A Check power source to see if it is normal Fan are not operatable B Check power inlet plug to see if itis plugged firmly into it s socket SOENT A Disconnect the power source Illuminating LED light does not work B Check LED light replace it with a new one if itis burned out A Check for damaged vanes Hood vibrates B Check if exhaust duct is secured S Replace The LED Light Before changing LED light ensure the uni
10. ettings B Always turn hood on when cooking at high heat or when cooking flaming foods ie Craepes suzetter charries jubilee peppercorn beef flambe C Clean ventilating fans frequently Grease should not be allowed to accumulate on fan or filter D Use proper pan size Always use cookware appropriate for the size of the surface element a WARNING To reduce the risk of injury in the event of a range top grease fire observe the following A SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray then turn off the burner Be careful to prevent burns If the flames do not go outimmediately EVACUATE AND CALL THE FIRE DEPARTMENT B NEVER PICK UP A FLAMING PAN You may be burned C DO NOT USEWATER including wet dishcloths or towels a violent steam explosion will result D USE AN EXTINGUISHER ONLY IF 1 You know you have a CLASS ABC extinguisher and you already know how to operate it 2 The fire is small and contained in the area where it started 3 The fire department is being called 4 You can fight the fire with your back to an exit WARNING Sufficient air is needed for proper combustion and exhausting of gases through the flue chimney of fuel burning equipment to prevent back drafting Follow the heating equipment manufacturer s guideline and safety standards such as these published by the National Fire Protection Association NFPA and the Ame
11. gt Drill electric of ratchet driver with 3 16 wood bit for drilling starter holes and 174 wood bit to drill an access holes in the cabinet or kitchen wall for the electric power line Onecommon screwdriver Plier for opening electrical knockout gt Two 1 thick x2 wide x12 approximate length wood strips for recessed bottom kitchen cabinet installation only Purchase locally Electrical wire and supplies to comply with local cords gt Four 1 long flat head wood screws purchase locally to mount Wood strips gt Pencil and ruler for marking locations Saber saw or keyhole saw for cutting the 1 x2 wood strips to length D Accessory Package 1 Wood screws 3 16 x1 L 6pcs 2 Wire connector with spring 3pcs 3 Washer 6pcs 4 6 7 Vertical starting round collar 1pc E Preparing The Range Hood 1 Remove the top electrical Electrical Knockout knockout you may plan to bring power to the range hood either through the cabinet or through the wall Fig 1 Fig 1 2 Insert a screwdriver into the knockout slot and bend the knockout back and forth Fig 2 3 You may have to use pliers to pull the loosened knockout free Fig 3 Fig 2 4 When installed the bottom edge of your range hood should be 28 32 above the top of the cooking surfa
12. ipt Use the original shipping box and packing materials and completely remove or cover the original shipping label Make sure that products are in brand new condition uninstalled un drilled and contain everything that came with the package as when you first received it If any parts or manuals are missing we have the right not to accept the return We suggest that you use a traceable and reputable carrier of your choice to ship your return Your credit or refund will be processed within 10 14 business days from the date we receive your return 2102 N Seaman Ave S El Monte CA 91733 TEL 626 350 1015 626 350 5215 FAX 626 350 1254 Website www windsterhood com Email support windsterhood com WINDSTER www Windsterhood com 2102 N Seaman Ave S El Monte CA 91733 TEL 626 350 1015 626 350 5215 FAX 626 350 1254 2006 2008 Windster Hoods Inc opecifications subject to change without notice
13. mounting screws all the way into the cabinet or into the 1 x 2 wood strips so the hood is secure Fi Color A green white black Fig 10 Fig 11 N Mounting Range Hood Without Cabinet 1 Using metal brackets and screws included center hood onto board and install screw 2 Remove the hood from the board and nail the wood board onto the wall Be sure the nail is in the center of the stud 3 Place the range hood on the board and tighten the screw T 4 Completely finished P Making The Electrical Connection 1 Remove stainless Baffle filters Ref P8 H 2 Remove screws on wiring case fish out wires through the wire case knockout Fig 12 3 Mark the electrical connection by fastening all wires to the existing wall wiring according to the their colors Black to Black White to White Green to Ground Fig 12 4 After connection is done reinstall wiring case cover and bottom board 5 Turn on power and check operation of fan and light 6 After completely installation reinstall the stainless Baffle filter and oil collector Ref P8 H Q Use and Care Night light sensor 000 NEM M Main power 3 speed fan selection Fan OFF LED light OFF vias p 1
14. nce Any repair modification alteration or adjustment not authorized by the manufacturer or an authorized service dealers Misuse abuse accidents or unreasonable use Incorrect electric current voltage or supply Improper setting of any control Improper chemical cleaning Light Bulbs Products purchased for commercial or industrial use such as in a hotel office restaurant or other business 4 Damage due to earthquake flood storm etc WINDSTER Defective Products All products will be inspected tested and carefully packed by the manufacturer before shipping to customers Products that are damaged during transit can only be exchanged for the same product under the condition that the customer must get a RMA Return Merchandise Authorization from Windster When products are received defective you must notify us within the 3 business days of receiving the package Replacement products are only shipped when the RMA is issued NO EXCEPTIONS Return Policy Windster offers only the best and highest quality products If you are not satisfied with your purchase please contact us within 3 business days of product arrival to obtain a Return Merchandise Authorization RMA Returns sent without a RMA will not be accepted There will be a 25 re stocking fee for every returned items shipping fee will also be deducted from the original purchase price When returning a package please include a copy of your purchase rece
15. nockout hole Fig 1 ELECTRIC WIRING C Screw the four 1 wood screws for mounting the hood into the exact center of the arrow and into the keyhole 4 mounting slots marked on the cabinet bottom for flush installations or marked on the 1 x2 wood strips for recessed cabinet installation Fig 7 Do not turn the mounting screws in all the way Allow 3 8 of screw to project Fig 7 so the hood can be fitted place The screws will be tightened later G Providing Electrical Power 1 After turning off the proper 120 volt circuit atthe service entrance drill outthe electrical power line access hole marked on the cabinet bottom or wall Use a 1 wood bit Fig 8 2 Fish the electrical power line through the access hole drilled in the wall or bottom of the cabinet Attach an appropriate connector purchased locally to the end of the power line for the type of wiring being installed Follow all codes Fig 9 Safety Warning If drilling into the walls be careful not to cut existing electrical cables which would create a hazard Color green white black a 13 4 bit Connecter Fig 8 Fig 9 H Remove and Reinstall Baffle filters 1 Wear safety workman gloves and 2 Push Baffle filter down ward hold the handles of Baffle filter then pull a little back Q
16. rican Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE and the local code authorities Keep the range hood clean WARNING To reduce the risk of fire use only metal duct work Hm B Safety Notes 1 All electrical work must be done in accordance with local and or national electrical code as applicable for safety This product must be grounded if your are unfamiliar with methods of installing electrical wiring secure the services of a qualified electrician 2 Turn off power at service entrance before installing wiring or servicing this product 120 volt for range hood 220 volt for electric range if any 3 Turn off power to avoid risk of fire electric shock or injury for cleaning or maintenance such as lubrication 4 Fireplaces gas furnaces water heaters require proper flow of combustion air and exhaust Make sure this flow is not altered when using any exhaust fan 5 Please read specification label on product for further information and requirements 6 Please wear Safety Gloves for installation cleaning light bulb changing and dismantling to reduce the risk of any injuries CAUTION Toreduce the risk of fire and to properly exhaust air be sure to duct air outside Do not vent exhaust air into spaces within walls or ceilings or into attics crawl spaces or garages M C Tools and Materials Required
17. t is pressed the D main power button off when you want to change the LED light please always wear working gloves 1 Using suitable tool small slotted screw driver gently pry off the LED light set 2 Taking off the wire connecter with LED light set 3 Replace a new LED light set and reconnect the wire to the connector 4 Before push back the original LED light position test the LED light gt oN LED driver A Model HP 1500 36 Np input 100 240vdc Q LED light 1W output 3 6vdc 1500maH Model HP 15A NOTE For LED light replacement you may not find the appropriate LED lights from market please contact with distributor s dealer s z G is O i d z al ao A Parts List No Description Parts no Per hood 1 Hood casing eee 3 2 Air chamber 38 02 1 3 Topplate 1 4 6 round vent Vertical ventilation 38 04 1 5 Motor housing 38 05 2 6 Inner vent Rear ventilation 38 06 1 f Motor s 38 07 2 8 Fan s 38 08 2 9 Oil tunnel 38 09 2 10 Spacer s 38 1042 42 38 048 49 2 11 Baffle filter s 38 11 2 12 Handle s 38 12 4 13 Oil collector 38 13 2 14 LED light 38 14 2 15 LED light fixture ere 490057 16 Control panel 38 16 1 17 Control button 38 17 1 18 LED driver 38 19 1 19 Bracket 38 20 2 20 Wiring partition 39 214242 38 2140 49 1 m With asterisk
Download Pdf Manuals
Related Search