Smeg LBS 635 User's Manual
Contents
1. Start Pause Cancel and all other leds will be off You can select a new program and start washing If cancel task is performed during washing Spin led on display will light on machine will pump and when Spin led is off door led will be on door can be opened and End of the Program new program can be selected After machine starts operation even if spin speed or washing temperature is changed initial soeed and temperature is valid In or der to change spin speed or temperature after pressing Start Pause Cancel new cycle or temperature can be selected When program ends door led will light on and door can be opened and machine Emptying Laundry is ready for next washing Press On Off for turning machine off After program ends machine automati cally stops Turn off tap water Pull the handle and open loading door Turn off your machine by pressing On Off After taking laundry out keep the loading door open and let the drum ventilate Check the bellow and clean J maintenance and cleaning Detergent Drawer The powder detergent remnants may accumulate in the detergent drawer To clean the detergent drawer pull the drawer towards you by pressing the marked point of the siphon in the softener compartment as shown in the illustration Wash the drawer in the sink with plenty of water Siphon Do not forget to clean the siphon the colored part2. 040 o o Very little dirty or heat resistan Synththetic 30 cotton synthetic compound Normal soiled cotton and linen sensitive to Mix 40 25 95 35 040 0 o o heat Delicate 40 Delicate sensitive synthetic cotton blended 1 5 70 35 0 30 e o Delicate 30 Delicate sensitive synthetic cotton blended 1 5 65 35 0 20 e Woolens and sensitive compounds with machine Woolen 40 washable label 1 5 55 30 0 20 e 8 Woolens and sensitive compounds with machine Woolen Cold washable label 1 5 45 30 0 05 e o Special program for laundries that have silk cash Hand wash 30 mere un washable in machine labels 1 90 28 20 Mini 30 Special program for Less soiled linens 1 5 30 30 0 10 e Rinsing Rinsing program 3 5 23 11 0 04 e Spin Spin Program 35 11 _ 0 03 e Pump Pump Program 3 2 S Energy Label Program EN 60456 1999 and IEC 60456 hardness and temperature environmental temperature Ed 4 2001 laundry type and amount auxiliary function selection and Water and power consumption may show differences changes in the electricity voltage from the table above depending on the water pressure Function Selection ED Additional functions selectable according to selected program can be selected by pressing related key Led of selected func tion will be on If not selected together some additional functions go off when it is no
3. 80 Q 30 4 5 10 20 0 The end of drainage hose can be connected directly to the waste water drainage hole or to the specific end that is installed to the outlet elbow of the sink The hose should be installed to a height of 40 cm minimum and 100 cm maximum ED Electrical Connection Plug in the grounded plug at the end of the power cable of the washing machine to a grounded wall outlet which is fed with suitable voltage and current Preparation Please note the followings before start ing to wash your laundry Have you plugged the machine Have you connected the drainage hose as necessary Have you closed the front door Have you opened the tap e f you are installing your machine by your self please read the Installation section first e Separation of the laundries to be washed Please separate the laundries according to their types cotton linen synthetic woolen etc dirtiness levels and washing tempera ture Do not wash the white clothes along with the colored ones Remove solid objects such as belts cuff links and curtain rods from the laundries or put them into a washing bag Empty the pockets Zip and button up It is recommended to place the very small laundries such as baby clothes into the big laundries such as pillowcases or put into a special washing filet in order to prevent them from sticking between the bellows or slipping into the cauldron p
4. Child proof lock led will be off During machine operation you can press Start Pause Cancel key for getting machine to Pause position In this case Start Pause Cancel led will blink EN Changing Program You can use this feature for washing laundry in the same textile group for wash ing at lower or higher temperatures For example instead of Cotton60 Cotton40 can be used For selecting Cotton40 instead of Cotton60 by pressing Start Pause Cancel key machine is switched to pause position Program knob is turned for selecting Cotton40 program Adding laundry Even when the program selection knob is changed during the program initially selected program will be executed For changing washing program continuing program must be cancelled Although selected auxillary functions must be compatible with washing program If you want to add laundry to your machine after program begins press Start Pause key for switching machine to pause mode If water level in the machine is appropriate door led on program progress display is on and laundry can be added to the machine If door led is not on after one minute than water level in the machine is not appropriate and laundry can not be added You can press Start Pause Can cel key for continuing program Cancelling a program For canceling a program Start Pause Cancel key is pressed for three seconds After this period
5. On Off button you can make your machine ready for selecting program When On Off key is pressed door led will light on meaning door can open Press On Off key again for turning your machine off Pressing On Off does not mean program started operation You must press Start ED Program selection table Determine the suitable program according to program selection table Turn the program the type amount dirtiness level and washing selection knob to the program temperature temperature of the laundry by looking at the position that you want to wash with _ gt 8 D 2 5 X ce eo Ely 2 alal sg ej Sz 52 22 82 F g 2 EA eee oe Ss e 58 j El l 8 Coton 90 Very dirty heat resistant cotton linen 3 5 50 45 145 10 Coton 60 Normal dirty heat resistant cotton linen 3 5 35 43 066 e o Coton 40 Less dirty or heat resistant cotton 3 5 25 40 045 0 o Intensive 60 Very dirty heat resistant cotton linen 3 5 60 50 0 80 e Intensive 40 Very dirty heat resistant cotton linen 35 60 50 0 50 ele Anti Heavy soiled Durable fabrics made of cotton 0 3 5 170 55 0 95 Hie Allergic 60 and linen baby clothes etc Normal dirty heat resistant cotton synthetic Synththetic 60 compound 2 15 35 070 0 Less dirty or heat resistant cotton synthetic Synththetic 40 compound 2 o5 35
6. in the detergent drawer when it gets dirty To remove the siphon first take out the detergent drawer To prevent clogging clean the softener remnants inside of it After cleaning put back the siphon and check if it is well seated or not Inlet Water Filters At the end of the water inlet valves which are mounted to the back of the machine and the flat end of the water inlet hoses that are mounted onto the taps there is one filter for each These filters prevent the foreign substances and dirt in the water entering the machine Filters should be cleaned when they get dirty To do this close the taps Remove the water inlet hoses Clean the tops of the filters on the water inlet valves with a thin brush If the filters are very dirty you can pull out with pliers and clean them The filters on the flat end of the water inlet hoses should be taken out with their gaskets by hand and cleaned thoroughly under the flowing water There are 2 filters in the machines with single cold water inlet and 4 filters in the machines with double hot cold water inlets RF Hose Since there is a risk of freezing especially in the cold areas the water remaining in the appliance can frozen and damage the appliance In this case the water remaining in the pump and hoses should be drained by removing the pump filter Water inlet hoses should also be emptied by removing them from the taps EN Cl
7. trans former use grounding installation must be performed with a licensed electri cian Any use before grounding is not our responsibility e Never place your machine over a car pet covered floor Otherwise electrical parts of your machine may overheat This may cause malfunction of your machine e Make sure hot and cold taps are connected correctly Otherwise your laundry may come out hot and torn e Please call certified service for a failure of electric plug cable e Be careful about your water hoses are bs not old Do not use old torn water hoses This may cause stain in your laundry e At first use washing must be per formed at Cotton 90 C program without loading with laundry for getting your machine ready for washing bd e Performance of your washing machine depends on the quality of water and hygiene compound used If low quality and unfitting cleaning material is used the stains will be fixed Before wash ing your laundry with stain keep your attention on cleaning the laundry as explained in following pages e This is period of keeping spare parts for your machine to operate Because of quality control procedures there might be little amount of water in your ED machine This does not have any dam age to your machine Your machine is programmed for starting operation again when electric ity is off and on afterwards You can not press On Off button to cancel program Machine will g
8. eaning the pump filter e Clean the foreign substance filter periodically at least for once e If the foreign substances coins buttons baby socks and etc clog the foamy water pump clean the filter e Before cleaning empty the water that remains inside first e Hot water danger There may be 15 liters of hot water at 90 C in the machine Open the filter carefully Drain the water completely in the following situations e before cleaning the foreign substance filter e before transporting the machine for example moving into a new house e when there is a risk of freezing 1 Turn off the appliance unplug the pow er cable and close the tap Wait for the hot soapy water to cool enough Otherwise there is a risk of scalding 2 Open the service cover by pressing the button In order to prevent the little amount of water that is inside pump spilling over the floor put a container in front of the filter cover Take out the filter by turning anticlockwise 3 To loosen the foreign substance filter turn it half turn anticlockwise and take the remaining water with a cloth When there is no water turn the foreign substance fil ter until it is totally released and take it out 4 Clean the foreign substance filter and pump opening 5 Reinstall the foreign substance filter and turn it tightly clockwise 6 Close the service cover
9. ee Smeg Washing machine LBS 635 ED Contents 1 Specifications of your Washing Machine gt 4 2 Warnings gt 5 Installation gt 6 4 Preparation gt 8 5 Program Selection and Operating Your Machine gt 9 Maintenance and Cleaning gt 13 Your Washing Machine 1 Detergent Drawer 4 Adjustable feet 2 Control panel H Front door 3 Tabletop 6 Filter cover EN 4 Specifications of your Washing Machine Maximum dry laundry capacity kg 3 5 Height cm 85 Width cm 60 Depth cm 35 Net Weight kg 58 Electricity V Hz 230 50 Total Current A 10 Total Power W 1800 Washing rinsing cycle cyc min 52 Spinning cycle max cyc min 600 In order to improve the product quality modifications can be made in the specifications without prior notice The illustrations in this guide are schematic and may not exactly match with your product The values that are declared in the markings on your product or in the printed documents accompanying are obtained in a laboratory environment according to the related standards These values may vary according to the usage of the product and environmental conditions 2 Warnings e This product is designed for home use e Your washing machine is adjusted to 230V e f the fuse in your house is less than 16A than have a certified electrician deploy an 16A fuse e Incase of transformer or non
10. ng the machine the transportation safety bolts must definitely be removed For this 1 Loosen the C bolts thoroughly by turning them anticlockwise with the help of a suitable wrench 2 Pull off the transportation safety bolts 3 Insert the P plastic caps in the direction of arrow into the holes from where the transportation safety bolts are removed Please note Keep the transportation safety bolts in a safe place in order to reuse them for any other transportation Transport your washing machine with the transportation safety blots installed 3 Adjusting the feet Your machine must stand level and balanced on its feet in order to operate more silent and vibration free First loosed the plastic counter nut on the adjustable feet of your machine After maintaining the balance by adjusting the feet tighten the plastic counter nut upwards Water connections a Water inlet hose The specific hoses that come with the machine are connected to the water inlet valves on the machine Red labeled hose is for hot water inlet and blue labeled hose is for cold water inlet In order to prevent the water leakages that may occur on the connection points rubber seals are placed on the hose or in the package 4 pieces for the models with double water inlets and 2 pieces for other models These gaskets should be used for connections in both sides of the hose Gaskets
11. o on program when electricity is on To CANCEL the program press gt Start Pause Cancel lt button for three seconds See Can celling a program If Door led on program progress dis play is blinking program selection knob is middle position In this case turn the knob and adjust it again If the warning continues call authorized service After your machine starts operation if Start Pause Cancel key starts blink ing than door is not locked Open and close the door again begin washing program again If the washing led on the program progress display is blinking either there is no water or tap is off Check your taps Turn your machine off and on If the problem persists unplug your machine turn off tap water and call authorized service If program is started and program selection can not be performed your machine might be in protection mode due to infrastructure problem voltage water pressure etc Press and hold the gt Start Pause Cancel lt button for 3 seconds in order to switch machine to factory settings Most of the warnings resulting in call ing an authorized service are due to infrastructure problems For this reason applying to an Authorized Service is recommended EN EJ Installation 1 Removing the packaging reinforcements To remove the packaging reinforcement lean the machine backward take the reinforcement by pulling from the braid Before operati
12. on the machine side should fit in the hose filter channel Since the connection points are under water pressure turn on the taps to the maximum after the connection Check if there is any water leakage at the connection points In order to prevent the water leakages and the damages they may cause keep the taps closed when you are not using the machine Minimum 1 bar and maximum 10 bars of water flow from the tap is enough for your machine to operate efficiently In practice 1 bar means that more than 8 liters of water per minute flows from a full open tap Install the elbowed end of the hose to your machine Hand tighten the nuts of the hose do not use a spanner Models with double water inlets can be used as a model with a single water inlet by using a plug Plug should be installed to the hot water valve A rubber gasket should be used in order to prevent water leakage from the connection point Do not connect the product with single water inlet to the hot water tap The product may switch to the protection mode if the temperature of the water connected to a product with double water inlet through a Y part and single water inlet is above 40 C a Water drainage hose Water drainage hose can be attached to the side wall of a sink or bathtub Hose should not be bend When the drainage hose is hanged on a sink or bathtub it can be secured with a hose bracket so that it will not fall 90 100 110 6 70
13. t selected Auxiliary Functions Prewash To wash the very dirty laundries you can use this function in the cotton and syn thetic programs Rinse Plus You can increase the number of the cur rent rinsing cycles by using this function Thus the risk of the sensitive skins get effected by the detergent remaining on the laundry is reduced Child proof lock with other one For example when using cotton program prewash and rinse plus auxillary functions can not be selected to gether After selecting prewash program if rinse plus key is pressed fast program will be on and prewash function led will go off No Spin If you press this button spinning pro gram will not be executed During washing laundry in order to main tain that program progress is not affected by pressing keys by children there is child proof lock To enable child proof lock after washing begins press Prewash and Rinse Plus function buttons together si multaneously for three seconds Pre wash additional function led will always blink After program ends in order to start a new program or alter the program you have to Program Progres After machine starts operation relevant program led on program progress display will be on When a step is completed that step s led is off and next step s led is on When program is completed Door led will be on again disable child proof lock To do this press same buttons for three seconds and
14. ts that are developed especially for automatic washing machines Avoid using bleachers that contain chlorine or sulfur Put the powder detergent and softener into the appropriate compartments in the detergent drawer and close the detergent drawer Pour the softener as recommended in the package generally lt 100ml i e 1 tea cup Never exceed the MAX marking If you put more it will mix into the washing water via siphon Ill and it will be wasted In this case it may be necessary to refill the softener If the softener is condensed over time it may be necessary to dilute with some water Otherwise condensed softener clog the siphon and block the flow I Compartment I the powder detergent compartment for prewash Il Compartment II the powder detergent compartment for main washing IIL Siphon The softener compartment 5 Program Selection and Operating Your Machine Control Panel Cotone ae a D Anti Allergico Freddo 3 Quotidiano ri taral Lavaggio a EN RisciaquuN Centrifuga A Scarico Awio Prelavaggio Extra Esclusione E o ae caren On Off LBS 635 EJ On Off button H Program follow up indicator 6 Spin speed selection knob E Program selection knob Start Pause Cancel button E Auxiliary function buttons Pressing On Off Pause Cancel for starting the program By pressing
15. ump filter hose and etc For stained laundries see the Practical and useful information section Your machine can wash the woolen clothes with a Machine Washable or Unfeltable label in the special woolen program without damaging them Sensitive clothes with a Do not wash in the machine or Hand wash silk pure wool cashmere and etc label can be washed in the hand wash program which is designed specifically e To open the front door grab the handle and pull it For your safety the front door of your machine can only be opened when the machine is not operating If the door LED is on the door can be opened e Loading the laundry into the machine Place the laundries by spreading and without compaction Place your hand woven clothes into the machine by turning inside out When closing the door make sure that no laundry is in between the door and the rubber bellows Push the front door to close it If the front door is not closed correctly washing does not start e The selection of detergent and soft ener The detergent amount depends on the hardness of water the amount of laundry and the dirtiness level of the laundry Recommended amounts are written on the detergent package If your laundries are not very dirty and or your water has a low hardness use less detergent as recommended in the detergent packages Otherwise you may encounter excessive foam You should use detergen
Download Pdf Manuals
Related Search