Pioneer DEH-P3370XM User's Manual
Contents
1. L a s a _ L l z i DEH P33 70XM This product conforms to CEMA cord colors Pioneer Printed in Japan SOYINK _ lt CRB1735 A gt UC lt KYMFZ 01G00000 gt r gt gt a C ere Connecting the Units Note e This unit is for vehicles with a 12 volt battery and negative grounding Before installing it in a recre ational vehicle truck or bus check the battery voltage e To avoid shorts in the electrical system be sure to disconnect the battery cable before beginning installation e Refer to the owner s manual for details on con necting the power amp and other units then make connections correctly e Secure the wiring with cable clamps or adhesive tape To protect the wiring wrap adhesive tape around them where they lie against metal parts e Route and secure all wiring so it cannot touch any moving parts such as the gear shift handbrake and seat rails Do not route wiring in places that get hot such as near the heater outlet If the insulation of the wiring melts or gets torn there is a danger of the wiring short circuiting to the vehicle body e Don t pass the yellow lead through a hole into the engine compartment to connect to the battery This will damage the lead insulation and cause a very dangerous short e Do not shorten any leads If you do the protection circuit may fail to work when it should e Never feed powe2. Insert the supplied extraction keys into the unit as shown in the figure until they click into place Keeping the keys pressed against the sides of the unit pull the unit out Fig 7 Fig 8 Installation DIN Rear mount Installation using the screw holes on the side of the unit 1 Remove the frame Fig 9 Frame Insert the release pin into the hole in the bottom of the frame and pull out to remove the frame When reattaching the frame point the side with a groove downwards and attach it 2 Fastening the unit to the factory radio mounting bracket Fig 10 Fig 11 Select a position where the screw holes of the bracket and the screw holes of the head unit become aligned are fitted and tighten the screws at 2 places on each side Use either truss screws 5 x 8 mm or flush surface screws 5 x 9 mm depending on the shape of the screw holes in the bracket Factory radio mounting bracket Screw Dashboard or Console Fig 9 Fig 10 Fig 11 Fixing the Front Panel If you do not operate the Detaching and Replacing the Front Panel Function use the sup plied fixing screws and holder to fix the front panel to this unit 1 Attach the holder to the front panel Fig 12 3 Fix the front panel to the unit using fixing screws Fig 14 Fixing screw Fig 12 Fig 13 Fig 14 Installing the Tuner Unit Mounting with Brackets Fig 15 T
3. Note When a subwoofer is connected to this unit instead of a rear speaker change the rear output setting in the Initial Setting Refer to the Operation Manual The subwoofer output of this unit is monaural sold separately Protect the Antenna Connector Screw 3 X 6 mm Fig 4 Installation Note e Before finally installing the unit connect the wiring temporarily making sure it is all connected up properly and the unit and the system work properly e Use only the parts included with the unit to ensure proper installation The use of unauthorized parts can cause malfunctions e Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle e Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop like an emergency stop e The semiconductor laser will be damaged if it overheats so don t install the unit anywhere hot for instance near a heater outlet e If installation angle exceeds 60 from horizontal the Head Unit might not give its optimum perfor mance Fig 5 60 Fig 5 When mounting this unit make sure none of the leads are trapped between this unit and the sur rounding metalwork or fittings Do not mount the tuner unit near the heater outlet where it would be affected by heat or near the doors where rainwater might splash onto it Before drilling any moun
4. apping screw 4 x 12 mm Screw 4 X 6 mm Bracket Car mat or chassis Drill 2 to 2 5 mm diameter holes Fig 15
5. eads without fail There is a possi bility of short circuiting if the leads are not insulat ed To prevent incorrect connection the input side of the IP BUS connector is blue and the output side is black Connect the connectors of the same colors correctly If this unit is installed in a vehicle that does not have an ACC accessory position on the ignition switch the red lead of the unit should be connected to a terminal coupled with ignition switch ON OFF operations If this is not done the vehicle battery may be drained when you are away from the vehi cle for several hours Fig 1 ACC position No ACC position Fig 1 The black lead is ground Please ground this lead separately from the ground of high current prod ucts such as power amps If you ground the products together and the ground becomes detached there is a risk of damage to the products or fire Cords for this product and those for other prod ucts may be different colors even if they have the same function When connecting this product to another product refer to the supplied Installation manuals of both products and connect cords that have the same function Connecting the Tuner Unit Fig 2 Multi CD player sold separately IP BUS Input IP BUS Output Blue Black Power Supply AA Antenna Input D P Yellow Satellite This Unit f Riser f f f Green Terrestrial N Antenna Unit AN 90XM sold separat
6. ely IP BUS cable To Head Unit Refer to Fig 3 Fuse holder Yellow To terminal always supplied with power regardless of ignition switch position Black ground To vehicle metal body Fig 2 Connecting the Units Connecting the Head Unit Fig 3 Antenna jack IP BUS input Blue IP BUS cable To Tuner unit x M Refer to Fig 2 Yellow To terminal always supplied with power regardless of ignition switch position Red To electric terminal controlled by ignition switch 12 V DC ON OFF Orange white To lighting switch terminal Black ground To vehicle metal body e Rear or Subwoofer output E i NEE n This Product anything to the speaker leads that are not With a 2 speaker system do not connect connected to speakers Perform these connections when using a different amp sold separately Blue white To system control terminal of the power amp or Auto antenna relay control terminal max 300 mA 12 V DC Front speaker Left Rear speaker or Subwoofer Rear speaker or Subwoofer i q Rear speaker or Subwoofer Connecting cords with RCA pin plugs sold separately Power amp Ed Front speaker White black Right Gray black Green Violet Green black Violet black pi i Rear speaker or Subwoofer
7. r to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead The current capacity of the lead will be exceeded causing overheating e When replacing fuse be sure to use only fuse of the rating prescribed on this unit and the fuse hold er e Since a unique BPTL circuit is employed never wire so the speaker leads are directly grounded or the left and right speaker leads are common e Speakers connected to this unit must be high power types with minimum rating of 50 W and impedance of 4 to 8 ohms Connecting speakers with output and or impedance values other than those noted here may result in the speakers catch ing fire emitting smoke or becoming damaged e When this product s source is switched ON a con trol signal is output through the blue white lead Connect to an external power amp s system remote control or the car s Auto antenna relay control ter minal max 300 mA 12 V DC If the car features a glass antenna connect to the antenna booster power supply terminal When an external power amp is being used with this system be sure not to connect the blue white lead to the amp s power terminal Likewise do not connect the blue white lead to the power terminal of the auto antenna Such connection could cause excessive current drain and malfunction To avoid short circuiting cover the disconnected lead with insulating tape Especially insulate the unused speaker l
8. ting holes always check behind where you want to drill the holes Do not drill into the gas line brake line electrical wiring or other important parts If the tuner unit is installed in the passenger com partment anchor it securely so it does not break free while the car is moving and cause injury or an accident If the tuner unit is installed under a front seat make sure it does not obstruct seat movement Route all leads and cords carefully around the slid ing mechanism so they do not get caught or pinched in the mechanism and cause a short cir cuit DIN Front Rear mount This unit can be properly installed either from Front conventional DIN Front mount or Rear DIN Rear mount installation utilizing threaded screw holes at the sides of unit chassis For details refer to the following illustrated installation methods DIN Front mount Installation with the rubber bush Fig 6 Holder After inserting the holder into the dash board then select the appropriate tabs according to the thickness of the dash board material and bend them Install as firmly as possible using the top and bottom tabs To secure bend the tabs 90 degrees Rubber bush Screw Fig 6 Removing the Unit Fig 7 Fig 8 Frame Insert the release pin into the hole in the bottom of the frame and pull out to remove the frame When reattaching the frame point the side with a groove downwards and attach it
Download Pdf Manuals
Related Search