Lucent Technologies MDW 9030P User's Manual
Contents
1. n Ofi 00 0000 0000H isos Use with Select button to choose a line or programmable intercom drop button Redial Press to dial again the last number manually dialed from the handset Select Use to move the Selection rectangle and with Column buttons to choose a line or programmable intercom drop button Also use to wake up the phone Mute Hold Press to turn the micro phone off for privacy Headset Connector Press to put a call on hold 24s Plug in the headset cord to use the headset Handset Display QO 0O amp Information you would see on a wired system phone s display except time based on your communications system LCL P D M1 or M2 Local Mode communications system WIRELESS TEST Handset in Wireless Test Mode VIBR Vibrator enabled PSEL Line Preselection enabled PRESELECTION ON OFF Line Preselection Mode status CHANGE BUTTN MAP Communications system setting is wrong MAP P D M1 M2 Button Mapping Mode setting NO LINK Hancset is not communicating with radio module MSG indicates that you have a message RANGE indicates that the handset is out of range or almost out of range Handset also beeps ON indicates that handset was turned on by pressing Gir Battery icon flashes to indicate a low battery condition Handset also emits 2 beeps No Ring icon indicates that the alerter2. is disabled MUTE indicates that handset microphone was turned off by pressing ute Line Status Indicators show the status of line or programmable intercom drop buttons See Line Status Indicators below Selection rectangle indicates the active row for line or program mable intercom drop button selection When the display is blank the handset is either turned off or in sleep mode Activate the display by pressing or Line Status Indicators Each line status indicator corresponds to a specific outside line or programmable intercom drop button PARTNER Systems A triangle is the equivalent of a green LED on a wired phone A rectangle is the equivalent of a red LED on a wired phone All Other Systems A triangle is the equivalent of a red LED on a wired phone A rectangle is the equivalent of a green LED on a wired phone 2 Volume Adjustment To increase or decrease the volume of the handset alerter or the receiver earpiece m Alerter Press the or the button while the MDW 9030P is awake but turned off If the display is dark the phone is in sleep mode press to wake it up then press the the button m Receiver Press the or the button while the MDW 9030P is turned on Battery Charger LEDs The color of the battery charger s LEDs indicates the state of the corresponding battery pack as shown in the following table OF If
3. it is the SPARE If it is the REFRESH LED portion of the Refresh cycle portion of the Refresh cycle LED the battery If it is the the Refresh button Battery pack in the Spare HANDSET LED was pressed and charger battery the battery pack in the Handset LED shows compartment the Handset battery pack Steady Is charging Is charging N A orange Steady green Is fully charged Is fully charged N A Flashing red Has one of the Has one of the N A See note following problems following problems e Is not seated e Is not seated properly in the properly in the charger charger e Has dirty e Has dirty contacts contacts e Is defective e Is defective Steady red Is in the Discharge Is in the Discharge Is in the Discharge portion of the Refresh cycle Note If either the SPARE LED or the HANDSET LED is flashing red both battery packs must be removed from the charger to clear the flashing red condition Address the possible problems for one battery pack at a time to determine whether one is bad If you need help when using your MDW 9030P with a PARTNER MERLIN or MERLIN LEG END system in the continental U S call 1 800 628 2888 For all other systems follow the procedure you normally use to get support for your communications system Outside the continental U S contact your Lucent Technologies Representative or local Authorized Dealer Making a Call 1 Press Gr
4. Lucent Technologies Bell Labs Innovations MDW 9030P Wireless Pocketphone Quick Reference 503 801 161 Comcode 107993149 Issue 2 March 1997 MDW 9030P Wireless Pocketphone Quick Reference Handset Co Headset On Off Receiver Press to turn the headset on if the headset is plugged in ON appears in handset display To turn off press again Turn on to make or answer a Call and turn off to hang up Lanyard Loop Receives the sound of your caller s voice unless a headset is connected Antenna Attach lanyard for carrying handset Volume Control nom Press to increase or to decrease volume of receiver or alerter On Off Press to turn the handset on ON appears in handset display To turn off press again Turn on to make or answer a Call and turn off to hang up Feat P Feature Program Press to use dial code features PARTNER systems only or to enter programming mode Conf Conference Press to conference in add another party to your call Trans Transfer Press to transfer a Call to another extension Extend fully to maximize the handset range and voice quality Handset Display J Displays status of lines and range Also see Handset Display pn next page Column 3 Redial Mut E gt G
5. ch 1997 Copyright 1997 Lucent Technologies MA
6. i 2 If desired press to move the Selection rectangle then press corresponding to the line you want Dial the call To end the call press Gwo7 Rw Answering a Call 1 Press Grif 2 Speak into the handset 3 To end the call press Gro Preselecting a Line or Button Once Line Preselection is enabled proceed as follows 1 If the display is blank press 2 If necessary press to move the Selection rectangle 3 Press corresponding to the line or button you want 4 Press to access the line or button Changing Settings or Performing Tests in Local Mode Make sure the handset is turned off Press and hold for 3 seconds While still holding press Gor Press one of the following A to enable or disable the alerter P for 3 seconds then to enable or disable Line Preselection V to enable or disable the vibrator W to enter Wireless Test Mode then for signal strength for voice quality for matching radio module and slot number RwWNSs to enter Local Test Mode 5 Press to exit A CAUTION The MDW 9030P handset is a radio device and like all radio devices should not be placed next to a pacemaker See Guidelines for Safe and Efficient Operation in MDW 9030P Wireless Pocketphone Installation and Use for more information PARTNER MERLIN and MERLIN LEGEND are registered trademarks of Lucent Technologies Lucent Technologies 503 801 161 Comcode 107993149 Issue 2 Mar
Download Pdf Manuals
Related Search