Lightolier IS:4X4 User's Manual
Contents
1. AMPING DEI CACCE reens wo SLOT 1 Turn off power 2 Pull REFLECTOR TRIM down until ends of TORSION SPRINGS reach EMBOSSED SLOTS 3 Squeeze TORSION SPRINGS to disengage from EMBOSSED SLOTS and remove REFLECTOR TRIM Replace lamp Do not exceed maximum wattage marking Replace REFLECTOR TRIM BALLAST REPLACEMENT FIG 11 F Make sure AC power is OFF at fuse box Remove REFLECTOR TRIM amp lamp s See E Undo WINGNUT s and remove UPPER REFLECTOR Remove NUTS that secure BALLAST PLATE to HOUSING Partially remove BALLAST PLATE from HOUSING Disconnect wire leads from BALLAST push in terminals Insert pin or paper clip in RELEASE SLOT Fig 11 Remove BALLAST from BALLAST PLATE and install new BALLAST 8 Insert wire leads into BALLAST Follow wiring diagram on BALLAST 9 Reattach BALLAST PLATE UPPER REFLECTOR lamp s and REFLECTOR TRIM LIGHTOLIER eona rinna ee a BALLAST BALLAST PLATE 7 FIG 12 WINGNUT wa UPPER REFLECTOR2. ING BARS EMT TUBING or CHANNELS to ceiling members Fig 5 FIK must be securely attached to and unable to lift from ceiling members after installation is complete WIRE ANCHOR CLIP MOUNTING BAR T BAR FIG 4 FIG 5 For wood joist construction Mounting bars may be used to secure FIK to joists Fig 6 MOUNTING BARS may be bent where required to allow precise placement of FIK between joists Use nails to secure to joists MOUNTING BAR ordering information 18 long Cat No 1950 27 long Cat No 1951 BALLAST NAILS JOISTS FIG 6 J BOX MOUNTING BAR Note If FIK is to be used with a WALL WASH LOUVER TRIM Fig 7 FIK must be installed with either J BOX side or BALLAST side parallel to wall to be washed A FIG 7 Direction of wall to be washed LIGHTOLIER LICSHTOLIER A GiG THomAS COMPANY 631 Airport Road Fall River MA 02720 READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before IS z 4X4 installation To prevent electric shock turn off electricity at fuse box before proceeding s Retain these instructions for maintenance reference B0502 Page 2 of 2 B ADJUST FIK ADJUSTMENT ADJUSTABLE Set FIK so that bottom edge is flu
3. READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE NSTRUCTION SHEET NO This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before IS m 4X 4 E B0502 Page 1 of 2 installation To prevent electric shock turn off electricity at fuse box before proceeding Retain these instructions for maintenance reference INSTALLATION PROCEDURE FOR 4X4 4X9 AND 9X9 MATRIX SERIES RECESSED DOWNLIGHTS A FRAME IN AND WIRE IN Install FRAME IN KIT FIK using ADJUSTABLE MOUNTING BRACKETS Fig s 1 3 Fixture must be secured to structural ceiling members Connect to supply leads white fixture lead to neutral white supply lead black fixture lead to hot supply lead bare copper and or green insulated wire s must be connected to supply ground Use wirenuts local hardware items Place all electrical connections in the J BOX and close cover 3 4 OR 1 1 2 CHANNEL ADJUSTMENT ADJUSTABLE MOUNTING FIK MOUNTING BRACKET HOUSING BRACKET FIG 1 SCREW ADJUSTABLE 1 2 EMT 11 16 OD BY OTHERS ADJUSTMENT SCREW ADJUSTABLE FIK MOUNTING FIK HOUSING BRACKET HOUSING FIG 2 FIG 3 For suspended T bar ceilings T bar ANCHOR CLIPS accessory No 1956 order separately may be used with 18 or 27 MOUNTING BARS Fig 4 or simply wire MOUNT
4. sh to or SCREWS MOUNTING recessed 1 8 above finished ceiling Fig 8 PAREA O FIG 9 FIK Final vertical adjustment may be made by means of ADJUSTMENT SCREWS on inside of FIK Base of FIK is provided with a FLUSH TO CEILING OR hole pattern Fig 9 to assist with the C CLOSE IN UP TO 1 8 RECESSED alignment of multiple FIK s This hole ieee pattern will facilitate the use of laser Close in and finish ceiling as required CEILING beams plumb lines etc FIG 8 D INSTALLATION OF REFLECTOR TRIM 1 Squeeze both TORSION SPRINGS and insert ends into EMBOSSED SLOTS 2 Push REFLECTOR TRIM up into FIK until flange is seated firmly against ceiling surface Care and Maintenance of Alzak REFLECTOR TRIM finish If handling of REFLECTOR TRIM with anodized or Alzak finish is required the use of clean white or plastic film gloves is recommended to avoid fingerprints TORSION Anodized or Alzak surfaces can be cleaned by the following methods SPRING EMBOSSED SLOT 1 Wipe off with a soft clean dry lint free cloth 2 Wipe off with a soft clean cloth dampened in mild detergent solution Rinse then wipe dry with lint free cloth or paper towel REFLECTOR 3 Wipe off with a clean cloth dampened with a solution of wetting agent and TRIM water such as 2 oz Per gallon Pluronic L62 LF by Wyandotte Products Wipe dry FIG 10 4 Use a liquid wax such as Glass Wax Avoid gritty cleaning agents E RE L
Download Pdf Manuals
Related Search