Life Fitness M051-00K61-C131 User's Manual
Contents
1. INTEGRITY AND CLUB SERIES CROSS TRAINERS CLSX amp CSX ASSEMBLY INSTRUCTIONS 051 00 61 131 Congratulations and welcome to the world of The following Component List and the step by step assembly procedures have been developed to make the set up of the Cross Trainer as quick and easy as possible Please take special note of the following important points prior to choosing a location and beginning assembly of the Cross Trainer IMPORTANT SAFETY INSTRUCTIONS DO NOT locate the Cross Trainer outdoors near swimming pools or in areas of high humidity DO NOT operate your Cross Trainer if it has been dropped damaged or even partially immersed in water If this occurs contact Life Fitness Customer Support Services at the number in the Operation Manual DO NOT locate the Cross Trainer any closer than 30 inches 76 cm to a television set DO NOT locate additional Cross Trainers any closer than 42 inches 107 cm from center to center to avoid interference cross talk between heart rate monitors DO keep the area around your Cross Trainer clear of any obstructions including walls and furniture Ensure that there is at least a 12 inch 30 cm clearance in front of the Cross Trainer DO verify the contents of the delivery carton against the accompanying parts list prior to setting the cartons and shipping material aside If any parts are missing contact Life Fitness Customer Support Service at the number listed in the2. 236 Ibs 107 05 kg with console Shipping Dimensions without console Length 80 in 203 cm Height 47 5 in 121 cm
3. DES LEVIERS DE P DALE IL CONTIENT TOUS LES L MENTS N CESSAIRES POUR L INSTALLATION 1 Before proceeding familiarize yourself with the parts of the Cross Trainer and make sure that you have received all the items described in the Component List 2 Locate the left and right FRONT COVER 9 amp 10 Using two PHILLIPS PAN HEAD POINTED SCREWS 3 mount the LEFT FRONT COVER 9 to the FRAME A Attach the RIGHT FRONT COVER 10 to the FRAME in the same manner using two PHiLLIPS PAN HEAD POINTED SCREWS 3 Secure the tops of the FRONT COVERS together using two PHILLIPS PAN HEAD POINTED SCREWS 3 CAUTION Do not overtighten the PHiLLIPS PAN HEAD POINTED SCREWS 3 3 Locate the RIGHT USER ARM 12 Snap the 2 PIN CONNECTOR 2PA located at the bottom of the RIGHT USER ARM into the 2 PIN CONNECTOR 2PB positioned at the top of the RIGHT ROCKER ARM B Feed the connectors and excess cable up into the RIGHT USER ARM Secure the RIGHT USER ARM to the RIGHT ROCKER ARM using three HEX SOCKET HEAD CAP SCREWS 1 and three INTERNAL TOOTH Lock WASHERS 18 Repeat the procedure for the LEFT USER ARM 11 and LEFT ROCKER ARM C Tighten all screws securely CAUTION Be careful not to pinch the WiRE HARNESSES when assembling the USER ARMS 11 amp 12 to the ROCKER ARMS B amp C 4 Detach and unwrap the WIRE HARNESS E 16P 4P located at the top of the MONOCOLUMN F Holding the CONSOLE SUPPORT ASSEMBLY 7 with the handgrips
4. Leveler Jam Nuts are tight Refer to the Cross Trainer model s corresponding Operation Manual V Read the entire Operation Manual before using the Cross Trainer LISTE DES V RIFICATIONS EFFECTUER AVANT LA MISE EN MARCHE V V rifiez si tous les dispositifs de fixation sont serr s V V rifiez si l APPAREIL D EXERCICE POLYVALENT est de niveau et stable R f rez vous au manuel d utilisation V V rifiez si les contre crous des v rins de mise niveau sont serr s R f rez vous au manuel d utilisation Lisez le manuel d utilisation dans son int gralit avant d utiliser l appareil d exercice polyvalent Before attempting to operate your Cross Trainer it is imperative that you familiarize yourself with the contents of the Operation Manual If your Cross Trainer does not behave as described in the OPERATION MANUAL contact Life Fitness Customer Support Services at 800 735 386 toll free within U S A Canada Refer to the OPERATION MANUAL for a contact list of International Offices Prior to your call please be sure you have located and noted the MODEL NUMBER amp SERIAL NUMBER The Model amp Serial number information of your Life Fitness Cross Trainer is listed on a label located on the front stabilizer Physical Dimensions Length 81 207 65 cm Width 28 in 71 12 cm Height 65 in 165 cm with console Weight CLSX 239 lbs 108 41 kg 243 Ibs 110 22 kg with console Weight CSX 232 lbs 105 24 kg
5. facing upward feed the WiRE HARNESS up through the neck and out the top access hole Carefully lower the CONSOLE SUPPORT ASSEMBLY into the MONOCOLUMN CAUTION Be careful not to pinch the WiRE HARNESSES E when assembling the CONSOLE SUPPORT ASSEMBLY 7 to the MONOCOLUMN F 5 Using two HEX SOCKET HEAD CAP SCREWS 1 and two FLAT WASHERS 8 secure the CONSOLE SUPPORT ASSEMBLY 7 to the MONOCOLUMN Tighten the SCREWS securely 6 Insert the GROMMETS 20 into the four holes on the CoNsoLE SUPPORT ASSEMBLY Locate the Accessory TRAY 17 Align the Accessory TRAY with the four holes on the CONSOLE SUPPORT ASSEMBLY Using four PHILLIPS PAN HEAD POINTED SCREWS 3 secure the ACCESSORY TRAY to the CONSOLE SUPPORT ASSEMBLY as shown Tighten the SCREws securely CAUTION Do not overtighten the PHILLIPS PAN HEAD POINTED SCREWS 3 7 Remove the adhesive back and install the PAD 23 Install the 22 8 Attach the 4 PiN 4P and 16 PiN 16P CONNECTORS to the corresponding JACKS on the back of the CONSOLE ASSEMBLY 4 9 Feed any excess WIRE HARNESS E down into the CONSOLE SUPPORT ASSEMBLY 7 Secure the CONSOLE ASSEMBLY 4 to the CONSOLE SUPPORT ASSEMBLY using four PHILLIPS PAN HEAD SCREWS 2 Tighten the ScREWS securely CAUTION Do not over tighten the PHILLIPS PAN HEAD SCREWS 2 CAUTION Be careful not to pinch the WIRE HARNESS E when assembling the CONSOLE ASSEMBLY 4 to the CONSOL
6. operation manual Save the shipping cartons in case of return DO read the entire Operation Manual prior to attempting to operate this machine as this is essential for proper use CONSIGNES DE SECURITE IMPORTANTES NE placez pas l appareil l ext rieur pr s d une piscine ou dans un endroit tr s humide NE faites pas fonctionner l appareil s il est tomb s il a t endommag ou s il a t partiellement plong dans l eau Si cela s est produit contactez le service apr s vente de life fitness au num ro fourni dans le manuel d utilisation NE placez pas l appareil moins de 76 cm d un poste de t l vision NE placez pas d autres appareils du m me type proximit Un espace d au moins 107 cm doit tre observ entre les parties centrales de deux appareils afin d viter les interf rences entre les contr leurs de rythme cardiaque MAINTENEZ la zone autour de l appareil libre de toute obstruction y compris murs et meubles Veillez laisser un d gagement d au moins 30 cm devant l appareil VERIFIEZ si l emballage contient toutes les pi ces de la liste jointe avant de le mettre de c t Si des pi ces sont absentes contactez le service apr s vente de life fitness au num ro indiqu dans le manuel d utilisation Conservez l emballage au cas ou vous devriez renvoyer l appareil LISEZ le manuel de l utilisateur tout entier avant d essayer de faire fonctionner cet appareil Ceci est indispensable son utilisati
7. E SUPPORT ASSEMBLY 7 10 Locate and install the CONSOLE SUPPORT CAP 19 onto the CONSOLE SUPPORT ASSEMBLY 7 as shown using four CAP SCREWS 21 11 Place the Back MONOCOLUMN COVER 6 over the PIVOT SHAFT at the top of the MONOCOLUMN F 12 Place the FRONT MONOCOLUMN COVER 5 on the opposite side of the BACK MoNOCOLUMN COVER 6 to cover the Pivor SHAFT G and CONSOLE SUPPORT ASSEMBLY MOUNTING SCREWS Interlock the top tabs and use two PHILLIPS PAN HEAD POINTED SCREWS 3 to secure the bottoms of the MONOCOLUMN Covers together Tighten the SCREWS securely CAUTION Do not over tighten the PHILLIPS PAN HEAD POINTED SCREWS 3 13 Locate one FRONT ROCKER COVER 13 and one BACK ROCKER COVER 14 Position the FRONT ROCKER COVER over the user side of the left end of the PivoT SHAFT H as shown making sure that it interlocks with the MONOCOLUMN Covers 5 amp 6 Place the BACK RockER Cover over the opposite side of the left 14 end of the PIVOT SHAFT in the same manner Secure the COVERS using three PHILLIPS PAN HEAD POINTED ScREWS 3 Repeat the procedure reversing front and back for the user right end of the PIVOT SHAFT CAUTION Do not over tighten the PHILLIPS PAN HEAD POINTED SCREWS 3 PRE OPERATION CHECKLIST Ensure that all fasteners are tight Make sure the Cross Trainer is properly leveled and stable Refer to the Cross Trainer model s corresponding Operation Manual Ensure that the
8. on correcte Part Description Hex Socket Head Cap Screw COMPONENT LIST Part Description Phillips Pan Head Screw 1 3 8 16 X 1 8 2 8 18 X 3 4 0017 00101 1645 0017 00101 1744 Phillips Pan Head Pointed Screw Console Assembly di Boda du 1o shipped separately 0017 00101 1242 P E 5 Front Monocolumn Cover 1 6 Back Monocolumn Cover Flat Washer 7 Console Support Assembly 1 8 0017 00104 0192 9 Left Front Cover 1 10 Right Front Cover 11 Left User Arm Assembly 1 12 Right User Arm Assembly 13 Front Rocker Cover 2 14 Back Rocker Cover Internal Tooth Lock Washer 17 Accessory Tray 1 18 0017 00104 0450 Grommet 19 Cap Console Support 1 20 0017 00042 0754 Cap Screw T 27 0017 00101 1746 i di bd 23 Pad 1 Tools Required for Assembly e Magnetic 2 Bit Phillips Screwdriver e 5 16 Hex Key Wrench e 1 27 Torx Key Wrench HARDWARE FLAT WASHER 8 INTERNAL TOOTH LOCK WASHER 18 Em 8 18 X 3 4 PHILLIPS PAN HEAD 8 18 X 10 PHILLIPS PAN HEAD SCREW 2 POINTED SCREW 3 E E 3 8 16 X 1 HEX SOCKET HEAD CAP SCREW 1 GROMMET 20 CAP SCREW T 27 21 IMPORTANT DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE PEDAL LEVERS ALL NECESSARY COMPONENTS NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT IMPORTANTES NE JETEZ PAS LE KIT PLAC SUR LE DESSUS
Download Pdf Manuals
Related Search