Liebherr HC 20 User's Manual
Contents
1. Wall Plate Figure 9 10 BLOCKING FOR SAFETY Mounting the anti tipping device on wooden floors Figure 11 1 Mark the center line of the appliance on the back wall Align the anti tipping bracket center to this line es WARNING SSSR Be sure that there is no plumbing or electrical wiring located in this area which screws or drills could damage 2 Fasten bracket to the wooden floor using 5 screws 1 4 x 2 1 8 Drill pilot holes if neces sary 3 Fasten bracket with 3 screws 1 4 x 2 1 8 into the wall plate Figure 11 Wall Plate Mounting the anti tipping device in cabinets deeper than 24 Figure 12 13 To ensure the compressor mounting plate reaches the anti tipping bracket at cabinets deeper than 24 a wooden spacer must be mounted between the appliance back and the wall The anti tipping bracket will be fastened to the floor downwards and to the spacer backwards ees WARNING SSSR Be sure the wooden spacer is fastened securely to the floor Measuring for mounting the wooden spacer at framed kitchen cabinets Figure 12 Depth of spacer depending on clearence between appliance and wall 1 1 2 35 24 lt Panel thickness Figure 12 Measuring for mounting the wooden spacer at frameless kitchen cabinets Figure 13 Depth of spacer depending on clearence between appliance and wall s 1 1 2 na2. The required airflow is directed through the toe kick area A 3 76 mm B 79 13 16 2027 mm A C 35 13 16 910 mm Figure 1 D 3 76 mm E 24 610 mm G 42 7 16 1078 mm H 37 1 8 943 mm Door swing clearence Figure 2 Please allow for door swing clearance at locations next to a wall The illustrated measurement is without mounted front panels Be sure to add your panel thickness and handle depth to this measurement in order to avoid interferences Q Figure 3 It is important to use the provided cover grille for the ventilation opening This opening must not be covered with a cabinet base 76 mm Figure 2 PLANNING INFORMATION Cabinet Opening Dimensions Figure 4 Cabinet Framed cabinet Frameless cabinet Height C Depth B Depth B A 36 914 mm i Electrical outlet l i IMPORTANT Do not install the shut off valve behind the appliance C E a o 15 3 8 i 390 mm 5 Water line opening Water supply line Figure 4 A et A gt IMPORTANT IMPORTANT At 24 cabinets the water line opening must be in the The free length of the water supply l
3. tipping forward the compressor mounting plate must have contact with the anti tipping bracket Figure 17 The water line is visible at the front of the appli ance Screw the OD adapter onto the solenoid valve and connect the water line with the adapt er Figure 18 Open the shut off valve for the water supply and check the entire water system for leaks Anti tipping bracket Compressor mounting plate Figure 17 Figure 18 13 INSTALLATION Leveling the appliance Figure 19 1 The height can be adjusted in front by twisting the leveling feet 2 Twist the adjusting bolt to set up the back of the appliance 3 Rotate leveling feet until firmly in place against the floor ees WARNING SSSR To prevent the appliance from tipping forward the leveling feet D Figure 19 must have contact with the floor 4 Align appliance with sides of kitchen cabinets by adjusting leveling feet and the supports 27 mm wrench AE i 5 mm socket Figure 19 Fasten the appliance in the recess Figure 20 Fasten the appliance in the recess through the upper and lower hinges of the refrigerator doors Use 2 screws for each hinge Figure 20 5 32 4 mm length 5 8 16 mm Figure 20 Before mounting the door panels Figure 21 Unscrew the upper attachment brackets of both refrigerator doors Fi
4. ECTRICAL SHOCK HAZARD e Electrically ground refrigerator e Do not use an extension cord e Failure to follow these instructions could result in fire or electrical shock ees WARNING SSSR ELECTROCUTION HAZARD Electrical Grounding Required This appliance is equipped with a three prong grounding polarized plug for your protection against possible shock hazards e DO NOT remove the round grounding prong from the plug e DO NOT use a two prong grounding adapter e DO NOT use an extension cord to connect power to the unit ees CAUTION SSSR To protect the refrigerator from possible damage allow the appliance to stand 1 2 to 1 hour in place before turning the electricity on This allows the refrigerant and system lubrication to reach equilibrium Customer s Responsibility A 115 Volt 60 Hz 15 Amp fused electrical supply is required We recommend using a dedicated circuit for this appliance to prevent electrical overload Follow the National Electrical Code and local codes and ordinances when installing the receptacle Blocking For Safety The anti tip bracket must be installed to prevent the unit from tipping after it is installed Refer to Blocking For Safety Unit Venting Do not restrict the air flow Air flow must be provided for the unit to operate PLANNING INFORMATION Unit Dimensions Figure 1 Unit Venting Figure 3 HC 20 appliances do not require any ventilation openings in the cabinet
5. Installation Instructions EST EE l For Fully Integrated NoFrost Combined Refrigerator Freezers Instructions de montage Pour le r frig rateurs cong lateurs combin s NoFrost encastr s iil pour une utilisation int gr e _ Instrucciones de instalacion Para combinados frigorifico congelador NoFrost incorporados para uso integrado yili G Parlez vous fran ais Voir page 19 Habla espa ol V ase p gina 37 IMPORTANT PLEASE READ AND FOLLOW THESE INSTRUCTIONS These instructions contain Warning and Caution statements This information is important for safe and efficient installation Always read and follow all Warning and Caution statements D Z WARNING Ea Warning indicates a potentially hazardous situation which if not avoided could result in death or serious injury es CAUTION SSSR Caution indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury IMPORTANT This highlights information that is especially relevant to a problem free installation Make sure incoming voltage is the same as the unit rating To reduce the risk of fire electric shock or personal injury installati
6. a EN Figure 13 11 ICEMAKER IceMaker The icemaker for a combined refrigerator freezer is located in the freezer compartment It must be connected to the water supply to function properly These instructions only refer to the installation of the icemaker Please refer to the Use and Care Manual provided with the appliance for operation instructions The combined refrigerator freezer must be level for the icemaker to function properly Safety Instructions and Warnings Do not install the water connection while the combined refrigerator freezer is connected to an electrical outlet e The connection to the water supply may only be made by a trained and licensed plumber e The water quality must comply with the drink ing water regulations for the geographical area where the appliance is located Water Connection e The water pressure must be between 21 8 87 0 psi 1 5 6 bar e Use a 1 4 OD copper line to connect the water supply to the solenoid valve This is not sup plied with the refrigerator Figure 14 e A shut off valve such as the saddle valve illus trated here must be installed between the hose line and the main water supply so the water sup ply can be stopped if necessary Do not install the shut off valve behind the refrigeration unit Figure 14 e If you have hard water we recommend you install a water softener Also a filter must be installed
7. e panels should be at least 5 8 inch 16 mm thick to Cabinet Opening C Refrigerator door panel D allow the connecting rails to be fastened to them 80 2032 mm 45 3 4 1162 mm 84 2134 mm 49 3 4 1264 mm IMPORTANT The maximum panel thickness is 3 4 19 mm 18 1 8 7 D 13 7 16 341 mm co 36 7 16 16 9 16 926 mm 421 mm Figure 8 C Cabinet Opening 9 BLOCKING FOR SAFETY Mounting the anti tipping device on concrete floors Figure 9 10 Secure the appliance in place so it does not tip for ward when the fully stocked doors are opened The anti tipping bracket is provided with the appliance Wall 1 Mark the center line of the appliance on the back wall Align the anti tipping bracket center to this line es WARNING SSSR Be sure that there is no plumbing or electrical wiring located in this area which screws or drills could damage 2 Drill a 3 8 diameter hole in any position as shown in Figure 9 using a carbide drill bit Wall Plate The depth of the holes must exceed the overall length of the anchors provided Figure 8 Clean the holes after drilling 3 Attach washer and screw on hex nut to the end of each anchor Drive in all 3 anchors Align the bracket center to the center line on the back wall again Fasten the anchors by turning the hex nut 4 Fasten bracket with 3 screws 1 4 x 2 1 8 into the wall plate Figure 10
8. gn the panel in TES vertical direction by loosening the screws left a and right Finally fasten the screws es CAUTION SSSR To avoid damage to the screws use the correct screwdriver only Do not overtighten 3 Pull out the lower freezer drawer and fasten the lower panel in the same way Align to the upper drawer panel before fastening the screws finally Figure 24 3 Loosen the four cross head screws of the bracket and move the panel to the left until it makes contact with the center rail Figure 25 4 Fasten the four cross head screws Figure 25 Screw 3 5 x 13 mm Figure 23 Figure 25 16 INSTALLATION 5 Close the door and check the height of the 9 Grasp the soft stop cylinder and pull down panel Figure 28 6 Align the panel in its vertical position if CE es necessary Loosen the hex nuts and turn the A CAUTION adusting bolts using a screwdriver for slotted The soft stop cylinder retracts in the screws Figure 26 detached state 7 Check the vertical position of the panel again and fasten the hex nuts finally Figure 28 Figure 26 10 Fasten the refrigerator panel with three screws To make it possible to fasten the refrigerator 4 x 16 mm at the bottom Figure 29 panel at the bottom the soft stop cylinder must be dismantled 8 Stick a small screwdriver under the retaining clamp and lever out Figure 27 Figure 29 F
9. gure 21 Unscrew the hex nuts and remove the brackets These brackets will be mounted onto the refrigerator door panels Figure 21 14 INSTALLATION Mounting the attachment brackets onto the door panels Figure 22 Fasten the dismounted brackets of the refrigerator doors onto the refrigerator door panels using four screws 4 x 16 mm for each bracket Fasten the brackets provided onto the freezer drawer panels using three screws 4 x 16 mm for each bracket The measures for bracket attachment are the same at framed and frameless cabinets because the height of the freezer panels is the same at both designs 1 15 16 1 15 16 49 mm 49 mm 1092 mm 1 8 3 mm CD 34 21 32 CD 880 mm 1 8 3 mm 1 8 3 mm a En 34 21 32 880 mm Figure 22 15 INSTALLATION Mounting the freezer drawer Mounting the refrigerator door panels Figure 23 panels Figures 24 31 The panels can be attached to the appliance now 1 Open the left refrigerator door and hang the The upper drawer panel must be mounted first panel on the adjusting bolts Figure 24 1 Pull out the upper freezer drawer and screw on 2 Screw on the hex nuts to the adjusting bolts and the panel with three screws at left and right hand fasten temporarily Figure 24 side using the screws as shown in Figure 23 2 Close the drawer and check the position to the D ZL surrounding cabinet panels Ali
10. if the water contains solids such as sand All equipment and devices used to supply the water to the appliance must comply with the cur rent regulations for your geographical area Cover strips Figure 15 Before connection to the water supply the cover strips provided must be fitted to the appliance It is necessary because the appliance will be moved into its recess Remove the cover band from the strips and stick 12 them to the left and right front edge of the appli ance housing Figure 15 Figure 15 ICEMAKER Connection to the Water Supply 1 Install the shut off valve water filter and auto matic shut off device as required The solenoid valve has a Metric R3 4 male con nector A R3 4 metric to a 1 4 OD adapter is supplied with the icemaker Move the appliance towards the final position and leave a gap of approx 30 behind Insert the water supply line into its intended opening at the back of the appliance Figure 16 Move the power supply line to the area of the electrical outlet es WARNING SSSR Do not connect to the electrical outlet before the installation is completed and the water line is connected to the solenoid valve Push the appliance slowly to the back wall until the compressor mounting plate makes contact with the anti tipping bracket Figure 17 es WARNING SSSR To prevent the appliance from
11. igure 27 17 INSTALLATION 11 Extend the soft stop cylinder and connect with the ball stud Figure 30 Sl D l e Figure 30 12 Attach the retaining clamp to the ball housing of the soft stop cylinder Figure 31 es CAUTION SSSR To avoid injury or damage do not forget to secure the soft stop device with the retaining clamp U Figure 31 Mounting the ventilation grille Figure 32 33 1 Pull out the bottom freezer drawer 2 Remove the blue protection film from the dust filter provided and insert the filter into its opening in the toe kick area as shown in Figure 32 Figure 32 3 Mount the ventilation grille as shown in Figure 33 IMPORTANT Only use the ventilation grille provided with the appliance This grille is required for proper operation of the appliance The ventilation opening must not be covered with a cabinet base Failure to use the supplied grille can result in product failure and will void the warranty Figure 33
12. ine must be at least location as shown in Figure 4 31 1 2 800 mm when the tube comes out of the At cabinets deeper than 24 there is room to fit the prescribed opening pipe behind the appliance and the wall so there are no requirements for the water line lead out position PLANNING INFORMATION Framed Cabinet Figure 5 Cabinet frame At Framed Cabinets the panel front is in line with the Cabinet frame Figure 5 IMPORTANT Please note the cabinet depth of 24 3 4 629 mm only at framed cabinet design PLANNING INFORMATION Panel Dimensions Framed Cabinet Design Figure 6 The panels should be at least 5 8 inch 16 mm thick to allow Cabinet Opening A Refrigerator door panel B the connecting rails to be fastened to them 80 2032 mm 45 9 32 1150 mm IMPORTANT 84 2134 mm 49 9 32 1252 mm The maximum panel thickness is 3 4 19 mm 1 4 1 4 17 3 4 451 mm 451 mm D f Q 2 lt x e D LLI 2 1 4 amp Cc 13 7 16 341 mm 1 4 35 3 4 16 9 16 908 mm 421 mm 1 8 Figure 6 PLANNING INFORMATION Frameless Cabinet Figure 7 At Frameless Cabinets the panels are in front of the Cabinet frame Figure 7 PLANNING INFORMATION Panel Dimensions Frameless Cabinet Design Figure 8 The gap between all panels at frameless cabinet design is 1 4 6 mm Th
13. llation Leveling the Refrigerator eeeeeeeeees 14 Fasten the appliance in the recess 14 Before mounting the door panels 0 1 14 Mounting the attachment brackets onto the door panels ccsseeeseeeeenee 15 Mounting the freezer drawer panels 16 Mounting the refrigerator door panels 16 18 Mounting the ventilation grille 18 INSTALLATION GUIDELINES Area Requirements Verify the following e Floors can support refrigerators weight plus approximately 1200 pounds 544 kg of food weight e Finished kitchen floor height is level Refrigerator must be adjusted if the floor heights are not equal to make sure air vents are not obstructed e Remove anything attached to rear or side walls that can obstruct refrigerator opening e Cutout dimensions are accurate e Electrical outlet is in correct location Do not install this refrigerator freezer next to any other refrigerator Installing this refrigerator freezer next to any other refrigerator or freezer can cause condensation or cause damage to the appliance Electrical Requirement If codes require a separate grounding circuit to be used have a qualified electrician install the circuit ees WARNING SSSR Do not ground to a gas pipe Check with a qualified electrician if you are not sure the appliance is properly grounded Do not have a fuse in the neutral or grounding circuit ees WARNING SSSR EL
14. on work and electrical wiring must be done by a qualified electrician in accordance with all applicable codes and standards including fire rated construction TO THE INSTALLER It is very important that the guidelines and instructions are followed in the manual to ensure proper installation and operation of the unit The Installation Guidelines section contains important information for making sure the installation is correct Read and understand all the information in the Installation Guidelines and in this manual before the unit is installed es CAUTION SSSR Always wear protective devices such as protective gloves and eye shields when installing the appliance Also use hearing protection when drilling holes into concrete floors Contents Page Planning Information Unit dimensions 0eeeeeeeeeeeeeeeeeeseenees 4 Unit Venting se scores ne te 4 Cabinet opening dimensions 5 Framed cabinet 6 Panel Dimensions Framed Cabinet Design 7 Frameless cabinet 8 Panel Dimensions Frameless Cabinet Design 0 eeeeeee 9 Blocking For Safety Mounting the anti tipping device on concrete OOIE tician aasa tate at 10 Mounting the anti tipping device on wooden TOOS ricana ae 11 Mounting the anti tipping device at cabinets deeper than 24 11 Ice Maker Safety instructions and warningS 12 Water connection 12 Cover StripS sde een 12 Connection to the water supply 13 Insta
Download Pdf Manuals
Related Search