JVC DT-V17L3D User's Manual
Contents
1. On the Status Display If you press the INPUT SELECT button rs 15 on page 6 currently lit the status of the input signal and setting of muting are displayed for about 3 seconds Make the setting to display hide the status in STATUS DISPLAY of the INFORMATION rs page 15 When STATUS DISPLAY is set to AUTO or ON the status below is also displayed in the following cases When you change the input When the signal condition of the current input changes When you turn on the monitor When STATUS DISPLAY is set to ON the signal format will remain displayed 3 seconds after the status is displayed 1080 60i MUTING ON Signal format For the contents displayed see On the signal format below and Available signals on page 9 Signal format of DVI input t DVI INPUT SEL on page 10 Setting of MUTING Displayed only when muting is activated t 4 MUTING button page 6 On the signal format The following messages appear depending on the type of input signals and their conditions When a DVI D signal protected with HDCP is input at the end of the indication When no video signal comes in NO SYNC When a noncompliant video signal comes in Out of range When COLOR SYSTEM FUNCTION SETTING on page 14 is set2. gt SIZE 000 POSITION 000 V SIZE 000 V POSITION 4 sub menu reset The menu automatically disappears in about 30 seconds after the previous operation lt WHITE BALANCE SET gt Some items may not appear gt COLOR TEMP 6500K on the menu depending on DRIVE n reset gt the input or the input signal B DRIVE 000 Are you sure The items controlled by R CUT OFF 000 YES then El G CUT OFF 000 NO then the MAKE system do not appear on the menu B CUT OFF 4 sub menu reset 000 R DRIVE BI 10 NOTE Settings of sub menu POSI The setting values and features are as follows LOWERt Displays the current setting and adjustment bar at the lower part of the screen UPPER 1 Displays the current setting and adjustment bar at the upper part of the screen LOWER2 Displays the current setting at the lower part of the screen UPPER2 Displays the current setting at the upper part of the 5 screen A you sure The adjustment bar is not displayed for some items YES then gt key NO then key Settings of SD4 3 LARGE The setting values and features are as follows OFF Fit the vertical picture siz
3. lt 1 gt A V buttons When a menu screen is displayed Selects or adjusts menu items Menu Operations on page 7 When no menu screen is displayed Selects the audio channels of EMBEDDED AUDIO signals Audio Channel Selection on page 7 SCREENS CHECK button lamp Displays only the selected element R G or B of the video signal Each time you press this button the screen changes in the following order RGB Normal screen Power lamp Unlit The monitor is completely off both the POWER switch and DC switch on the rear panel are turned off Lights in Green The monitor is on Lights in orange The monitor is off on standby Flashes in orange The monitor is in the P SAVE Red screen e Pressing lt button while holding V button displays the Bluescreen Greenscreen power save mode NO SYNC ACTION in SET UP MENU rs Menu Operations page 7 17 ASPECT button lamp SYNC FUNCTION on page 13 cinis RAPERE 6 MENU button Changes the aspect ratio of the picture from 4 3 17 5 button Activates deactivates the display of the MAIN MENU Menu Operations on page 7 7 COLOR OFF button lamp Displays only the luminance signal This function does not work for RGB input signals 1 1 button lamp Displays the picture in the original resolution of the input signal The aspect ratio of the p
4. 0 5 Clock shield The signal is recognized as 1080 60 7 DDC Data 15 GND 23 TM DS Clock 8 NC 16 Hot Plug Detect 24 T M D S Clock Attaching the power cord holder CAUTION Use only the provided screws Make sure the plug will not be pulled out after the cover is attached to the case The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN terminal The power cord holder consists of two parts a case and a cover To detach the cover 1 ACIN 2 Case terminal ep N xi Cover Menu Configuration MAIN MENU For the operation procedure see page 7 a E gt lt MAIN MENU gt nr lt PICTURE FUNCTION gt gt PICTURE FUNCTION APERTURE FREQ OFF APERTURE FREQ 0FF BACK LIGHT 00 APERTURE LEVEL 01 DVI INPUT SEL AUTO CTI OFF APERTURE LEVEL 01 MARKER LTI 0 E AUDIO SETTING 1 P MODE NORMAL WAVE FORM SETTING 4 sub menu SYNC FUNCTION reset ENTER gt SELECT B EXIT LTI OFF I P MODE NORMAL Operation guide Shows the buttons for each operation lt reset gt A Are you sure YES then Dl key NO then key The menu automatically disappears in about 30 seconds after the previous operation Some items may not appear on the menu depending on the input or the input signal The item
5. Settings for marker functions 1 2 Item To do Setting value AREA MARKER Activate deactivate the area marker and select the t NOTE style of it MARKER ASPECT Select the aspect ratio of the area marker 4 3 14 9 13 9 2 35 1 1 85 1 1 66 1 SAFETY MARKER Activate deactivate the safety marker and select the NOTE style of it SAFETY AREA Adjust the area of the safety marker 80 100 FRAME Displays hides the frame indicating the area of the OFF ON specified aspect ratio CENTER MARKER Displays hides the marker indicating the center OFF ON position of the picture LINE BRIGHTNESS Adjust the brightness of the marker HIGH LOW 2 2 Item To do Setting value R AREA MARKER Activate deactivate the area marker and select the style of it is NOTE R MARKER ASPECT 3 Select the aspect ratio of the area marker 4 3 14 9 13 9 2 3511 1 8511 1 66 1 R SAFETY MARKER Activate deactivate the safety marker and select the style of it is NOTE R SAFETY AREA Adjust the area of the safety marker 80 100 The area marker or the safety marker is displayed by using AREA MARKER or SAFETY MARKER button or external control Select either non R items or R items to activate by using external control External Control on page 16 When a picture is displayed in 4 3 aspect ratio the safety marker for the 4 3 area is display
6. 17 V External dimensions Width 395 mm 15 5 8 with the stand 395 mm 15 5 8 without the stand excluding protruding parts Height 344 8 mm 13 5 8 with the stand 304 mm 12 without the stand Depth 199 mm 7 7 8 with the stand 86 mm 3 1 2 without the stand Weight 7 kg 15 5 Ibs with the stand 5 3 kg 11 7 lbs without the stand Accessories AC power cord Power cord holder x 1 Screw x 2 for power cord holder Ferrite core x 1 for external battery 500 mV rms high impedance AUDIO MONITOR OUT Analog audio signal output 1 line RCA connector x 2 500 mV rms REMOTE MAKE TRIGGER Using the MAKE TRIGGER system on page 17 REMOTE RS 485 REMOTE RS 232C Audio External control Using the serial communication on page 18 Use the Anton Bauer Dionic 90 mount QR DXC M34A external battery For easy understanding pictures and illustrations are shown by being emphasized omitted or composed and may be slightly different from actual products Design and specifications are subject to change without notice CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type All company names and product names mentioned herein are used for identification purposes only and may be the trademarks or registered trademarks of their respective companies No
7. BACK LIGHT 00 MARKER ASPECT 4 3 DVI INPUT SEL AUTO SAFETY MARKER OFF MARKER SAFETY AREA 80 AUDIO SETTING FRAME OFF WAVE FORM SETTING CENTER MARKER OFF SYNC FUNCTION LINE BRIGHTNESS HIGH lt MARKER gt 2 2 gt R AREA MARKER ENTER Bl SELECT B R MARKER ASPECT R SAFETY MARKER R SAFETY AREA Operation guide Shows the buttons for each operation The menu automatically disappears in about 30 seconds after the previous operation Some items may not appear on the menu depending on the input or the input signal The items controlled by the MAKE system do not appear on the menu NOTE Setting of AREA MARKER SAFETY MARKER R AREA MARKER R SAFETY MARKER The setting values and features are as follows OFF Deactivate the marker LINE Displays the area with an outline HALF The area outside the specified aspect ratio of the screen is displayed at 50 transparency HALF L The area of the specified aspect ratio of the screen is indicated by an outline and the area outside of that is displayed at 50 transparency The area outside the specified aspect ratio of the screen is black Only the portion of the picture within the designated area is displayed BLK L The area of the specified aspect ratio of the screen is indicated by an outline and the area outside of that becomes black so that only the area inside the line is displayed BLK MARKER 2
8. If the product is installed in a place where you cannot easily plug unplug the power cord equip an easily accessible device to the wiring of the building for turning on off the power When the product is left unattended and unused for a long period of time unplug it from the wall outlet and disconnect the cable system Do not overload wall outlets extension cords or convenience receptacles on other equipment as this can result in a risk of fire or electric shock Use only the accessory cord designed for this product to prevent shock Slots and openings in the cabinet are provided for ventilation These ensure reliable operation of the product and protect it from overheating These openings must not be blocked or covered Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short circuit the parts which could result in a fire or electric shock Never spill liquid of any kind on the product Never place anything on the product Placing liquids naked flames cloths paper etc on the product may cause a fire Do not apply any strong shock to the LCD panel Do not hit any object against it or push it with a sharp pointed tool Do not put heavy objects on the product Do not step on or hang on the product Caution for use of the product in the high temperature Do not use the product in places of high temperature otherwise parts of this product or the LCD panel may
9. are flashing 2 Press 1 button to turn off on standby the monitor 3 Turn off the POWER switch and DC switch on the rear panel 4 When the AC power supply is used Disconnect the AC power cord from the AC outlet When a DC 12 V power supply is used Detach the battery or disconnect the plug from the DC IN 12V terminal 5 Contact your dealer with the information about which lamps were flashing f you turn on the monitor soon after turning it off or after a short term power failure the INPUT SELECT lamps may flash and no image may be displayed When this happens turn off power and wait at least 10 seconds before turning on the monitor again If the INPUT SELECT lamps do not flash you can use the monitor as normal Unplug this product from the wall outlet before cleaning Screen To avoid irreparable change in appearance of the screen such as uneven color discoloration scratches be careful about the following Do not paste or stick anything using any glues or adhesive tapes Do not write anything on the screen Do not strike the screen with a hard object Avoid condensation on the screen Do not wipe the screen with solvent such as alcohol thinner or benzine Do not wipe the screen forcefully Wipe stains off the screen with a soft cloth If the screen gets heavily stained wipe it with a soft cloth soaked in water diluted neutral detergent and wrung well then wipe with a soft dry cloth Cabinet To av
10. be damaged This product is equipped with a temperature sensor to give warning if the temperature becomes too high If the temperature exceeds the range of normal use TEMP OVER is displayed and the power is turned off automatically if the temperature becomes any higher In this case move the product to a place of low temperature to let it cool down U S A only FCC NOTICE CAUTION Changes or modifications not approved by JVC could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense IMPORTANT RECYCLING INFORMATION This product has a fluorescent lamp that contains mercury Disposal of these materials may be regulated in your community due to environmental considerations For disposal or recycling information please contact your local authorities or for USA the Electronic Ind
11. cause and corrective action Page Symptom Probable cause and corrective action Page Press the 5 button 6 The picture becomes Adjust the picture contrast or brightness by using the adjustment 6 14 Turn on the POWER switch or DC switch on the rear panel 8 blurred knobs on the front panel Or adjust CONTRAST or BRIGHT of No power supply Firmly insert the AC power plug or DC 12 V power plug 8 PICTURE SUB ADJ in the SET UP MENU When using a DC 12 V power supply charge the battery or replace it 8 Check whether the setting of 1 1 or ASPECT buttons is appropriate 6 with a charged one Check whether the input signal format is acceptable on the monitor 9 Select the correct input using the INPUT SELECT buttons 6 Wrong picture position Adjust the picture size SIZE V SIZE or position POSITION V 14 No picture with the Connect the signal cable firmly 8 wrong picture size POSITION of SIZE POSI ADJ the SET UP MENU Turn on the power of the connected component and set the output For some signals the picture cannot be displayed fully the effective power on 6 correctly Screen area There is no sure method to solve this problem Check whether the input signal format is acceptable on the monitor 9 The items which are not available for the current input or the current Adjust the volume level 6 Somentamedonot input signal are not displayed on the menu Change the input or th
12. cause damage to the monitor or injury You can place the monitor in the following two ways when using it on the supplied stand You can tilt the monitor as follows Monitor 1 About 12 pe 0 5 About 8 pae ne When the monitor is not tilted 0 the guidelines align as illustrated below Guidelines You can select the stand height higher position or lower position To adjust the stand height on page 5 CAUTION Be careful not to pinch your fingers in the gap between the monitor and the stand When the stand plate is attached to the lower position of the stand body you cannot tilt the monitor downward When the stand plate is attached to the higher position of the stand body To adjust the stand height on page 5 you can place the monitor as illustrated below 1 Remove the screws on the right side of the stand see the illustration below then lift the stand up by about 144 OC 2L Screw silver About 144 2 Attach the removed screws and place the monitor as illustrated below To place the monitor as illustrated on the left again remove the screws on the right side of the stand return the monitor angle to 0 then reattach the removed screws CAUTION When lifting up the stand lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel from being damaged be careful not to pinch your fingers in
13. signal 1 line BNC connector x 6 Number of pixels displayed 1440 x 900 Y 1 V p p 75 Q Number of colors displayed 16 77 million NT E BUR e brid iod Viewing angle 160 Horizontally 140 Vertically aea MC M HN MAE 1 2 Panel brightness AT eens E AUDIO HD SD SDI IN 1 Digital signal input compatible with EMBEDDED AUDIO signals Contrast ratio TYP 600 1 E AUDIO HD SD SDI IN 2 auto detection 1 line BNC connector x 1 Mou dea frequency v d uem 75 000 2 E AUDIO HD SD SDI Digital signal output compatible with EMBEDDED AUDIO signals computer signal od ot SWITCHED OUT 1 line switched out BNC connector x 1 Some signals within this frequency range may not be displayed Out of AUDIO IN Analog audio signal input 1 line RCA connector x 2 range is displayed Compliant video signal format Available signals on page 9 Format HD SDI BTA S 004B SMPTE292M SD SDI ITU R BT 656 525 625 SMPTE259M 525 EMBEDDED AUDIO SMPTE299M SMPTE272M Audio output Internal speaker 1 0 W 1 0 W Operating conditions Operating temperature 5 C 35 C 41 F 95 F Operating humidity 20 80 non condensing Slightly variable depending on ambient conditions for installation Power requirements AC 120 V AC 220 240 V 50 Hz 60 Hz DC 12 17V Rated current 0 56 A AC 120 V 0 36 A AC 220 240 V 3 0 A DC 12
14. the moving parts Make sure of lifting the stand up until it stops about 144 otherwise the monitor may fall over Place the monitor on a mat to avoid scratching the table surface Do not lift up the stand when the stand plate is attached to the lower position of the stand body When the battery is attached the stand may not be lifted up depending on the type of the battery To detach the stand CAUTION Lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel from being damaged 1 1 o g Attachment screws Ecl DN j Screw holes for stand attachment d Pel oa Stand body lt gt Monitor To install the stand When attaching the stand to the monitor insert the guides of the stand into the guide holes on the monitor to place the stand in the correct position Then fix the stand firmly with the attachment screws Guide holes Guides Screw holes for stand attachment S Stand plate Stand body To adjust the stand height To change the stand height detach the stand from the monitor To detach the stand on page 4 Then change the position of the stand plate according to the stand height you want by choosing the screw holes to use Higher position Screw holes for higher position Stand plate 59 S d R e 0 Stand body Lower position Screw holes for lower po
15. to AUTO and the noncompliant composite video signals come in OTHERS Daily Operations Connections cont Rear panel Carry handle RS 232C Use this handle when carrying the monitor REMOTE IMAKE TRRIGER CAUTION Do not connect the power cord until all other connections are completed REMOTE terminal Terminal for controlling the monitor by an external control rs External Control on page 16 VIDEO terminals BNC Input IN and output OUT terminals for the composite video signals COMPO Y Ps B Y Pr R Y terminals BNC Input IN and output OUT terminals for the analog component video color difference signals AUDIO IN terminals pin jack Input terminals for the analog audio signals Use this terminal for the analog audio connection of the SDI AUDIO MONITOR OUT terminals pin jack Output terminals for the analog audio signal The terminals emit the audio signals through the AUDIO IN terminal or EMBEDDED AUDIO signals through the E AUDIO HD SD SDI IN 1 or IN 2 input terminal The signal is output from this terminal only when the monitor is on or in SAVE power save mode NO SYNC ACTION in SYNC FUNCTION on page 13 The EMBEDDED AUDIO signal is decoded into an ana
16. 11 12 9 10 11 12 9 12 3G channel s 1 2 3 4 5 6 7 8 9 1 0 4 1 4 2 1 2 3 4 5 6 7 8 9 10 11 12 1 4 1G 5 8 2G 9 12 3G 8 10 20 1 12 1 3G Example of the level meter display Level meter position and audio channels Ex When LEVEL METER ch is set to LINE and BAR is set to X COLORS OVER LEVEL REFERENCE LEVEL mmm o 1 1 1 Yellow Green When BAR TYPE is set to W 100 the standard input level set in REFERENCE LEVEL is displayed with the line indication The input level set in OVER LEVEL is not displayed The level meter with no audio signal input is displayed in white for 3COLORS and in gray for W 100 You can select the position of the level meter display top or bottom of the screen POSITION in INFORMATION on page 15 L AUDIO SETTING 12 Settings for the audio output balance EMBEDDED AUDIO signals and level meter Item To do Setting value BALANCE Adjust the balance between the right and left L5 L1 0 R1 R5 Speakers E AUDIO GROUP Select the audio channel group of the t NOTE EMBEDDED AUDIO signals LEVEL METER Adjust the level meter display for the t NOTE SETTING EMBEDDED AUDIO signals LEVEL METER ch Select how the audio channels are displayed on OFF LINE Displays the channels 1 6 the level meter at the left of the screen and 7
17. 12 at the right DIVIDE Displays the odd channels at the left of the screen and the even channels at the right BAR TYPE Select the color of the level meter display 3COLORS 3 colors to indicate variations in input levels W 100 white REFERENCE Select the standard input level indicated on the 20dB 18dB LEVEL level meter OVER LEVEL Select the input level s lower limit indicated in red for the 5 display 10dB 8dB 6dB 4dB 2dB BAR BRIGHTNESS Select the brightness of the level meter Memorized for each input LOW HIGH MENU lt MAIN MENU gt lt WAVE FORM SETTING gt lt OVER LEVEL gt PICTURE FUNCTION gt MARKING OFF BACK LIGHT en a LEVEL 070 DVI INPUT SEL AUTO ay WARKER AUDIO SETTING ON gt WAVE FORM SETTING SYNC FUNCTION ENTER gt EXIT MENU Operation guide Shows the buttons for each operation lt SYNC FUNCTION gt gt NO SYNC ACTION OFF DELAY TIME 30sec LOW LATENCY 0N NOTE Example of the wave form monitor Ex When MARKING is set to ON and LEVEL is set to 080 Red White The wave which goes over the value set on LEVEL is indicated in Red WAVE FORM SETTING Settings for the wave form monitor Item To do Setting value POSITION Select the position of the wave form
18. 8 Troubleshooting esee 19 Self check program 20 nnna 20 Specifications 21 General 21 Input output 21 DIMENSIONS va en aed ex dehet 22 LCT2457 001A Safety Precautions WARNING REDUCE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE NO OBJECTS FILLED WITH LIQUIDS SUCH AS VASES SHALL BE PLACED ON THE APPARATUS IMPORTANT SAFEGUARDS Electrical energy can perform many useful functions This unit has been engineered and manufactured to assure your personal safety But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRIC SHOCK OR FIRE In order not to defeat the safeguards incorporated into this product observe the following basic rules for its installation use and service Please read these IMPORTANT SAFEGUARDS carefully before use All the safety and operating instructions should be read before the product is operated The safety and operating instructions should be retained for future reference All warnings on the product and in the operating instructions should be adhered to All operating instructions should be followed POWER CONNECTION The power supply voltage rating of this product is AC 120 V For U S A and C
19. GA60 4 Non inter 7 480 60p 480 60p 720 60p Non inter 8 576 50p 576 50p 1080 60p 4 Non inter 640 480 60p 640 480 60p 720 50p Non inter 720 60p 720 60p 1080 50p 4 Non inter 720 50p 720 50p d 4 When No 7 10 12 and 14 signals in thin lines will become obscured because their signal resolution is higher 720 30p 720 30p y than the screen resolution 720 25p 720 25p y Non preset signals may not be displayed normally even if their frequency is within the acceptable range 720 24p 720 24 y Horizontal vertical frequency computer signal on page 21 1080 60i 1080 60i When a preset signal comes in the signal format is shown on the status display For other signals the 1035 60i 1035 60i resolution is shown 1080 50i 1080 50i 1080 60 1080 60 Specification of the DVI D HDCP terminal 1080 50p 1080 50p Connect it to the DVI D output terminal on a personal computer 1080 30p 1080 309 y 16 Pin No Input signal Pin No Input signal Pin No Input signal 1080128 1080 25 8 1 TM D S Data 2 9 TM D S Data 1 17 TM DS Data 0 1080 24p ine 2 T M D S Data 2 10 TM DS Data 1 18 TM D S Data 0 1080 30p5F 1080601 Liu Bc 3 0 5 Data 2 shield 11 TM D S Data 1 shield 19 TM D S Data 0 shield 1080 24psF 1080 24psf Y 3 4 12 NC 20 ING t Analog component signals are compatible with Y on sync signals 5 NC 13 NC 21 NC 2 Compatible with EMBEDDED AUDIO signals 6 DDC Clock 14 5 V Power 22
20. MATION on page i 1080 60 i CAMERA 1 TC 12 34 56 01 m Audio level meter Not displayed when LEVEL METER ch is set to OFF AUDIO SETTING on page 12 Signal format Displayed when STATUS DISPLAY is set to ON INFORMATION on page 15 For the contents displayed see On the signal format below and Available signals on page 9 Source name assigned in CHARACTER SET Displayed when SOURCE ID is set to ON Displayed in large letters when STATUS DISPLAY is set to OFF or AUTO t INFORMATION on page 15 CRC error indication Displayed when CRC ERROR is set to ON INFORMATION on page 15 Ared square is displayed when an error occurs Time code When the input signal includes no time code 1 is displayed 14 T C time code button lamp on page 6 When any information of 1 2 3 or 4 above is displayed while signals come in from equipment other than a computer the picture is displayed without overlapping the information display area However the information display will overlap with the picture when displaying the picture with higher resolution than the resolution of the panel in 1 1 mode SD4 3 LARGE setting is ON FUNCTION SETTING on page 14
21. NFORMATION on page 15 Off On Wave form monitor display Color off Monochrome Screens check Change a mode according to a input picture Muting on off No function 3 Selects which functions in MARKER are activated non R items or R items MARKER on page 11 4 Displays the information shown when INPUT SELECT button of the current input is pressed gt On the Status Display on page 7 While controlling with the MAKE system the information is displayed only at the moment of short circuiting 5 While controlling with the MAKE system the level meter is switched between displayed short circuiting and hidden opening When LEVEL METER ch is set to OFF the level meter is not displayed EFFECT appears While controlling with the TRIGGER system the pattern of the audio channel display is switched 6 Must be controlled with the TRIGGER system Controls whether displaying hiding the wave form monitor This function cannot be controlled with the MAKE system 7 While controlling with the MAKE system the screen is switched between normal screen opening and blue screen short circuiting While controlling with the TRIGGER system the screen changes as same as when pressing SCREENS CHECK button 11 on page 6 8 Must be controlled with the TRIGGER system The mode changes in the order of NORMAL CINEMA FIELD This function cannot be contro
22. The lightning flash with arrowhead symbol within an equilateral triangle is CAUTION intended to alert the user to the presence of uninsulated dangerous voltage RISK OF ELECTRICAL SHOCK AN within the product s enclosure that may DO NOT OPEN be of sufficient magnitude to constitute a risk of electric shock to persons JVC CAUTION To reduce the risk of electric shock Do The exclamation point within an not remove cover or back No user equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance DI V17L3D INSTRUCTIONS MULTI FORMAT LCD MONITOR serviceable parts inside Refer servicing to qualified service personnel Safety 2 IMPORTANT SAFEGUARDS 2 1 eerte re merces 4 Daily Operations Connections 6 Front panel 2 2 6 Rear panel eese 8 Available 9 Menu Configuration MAIN MENU 10 Menu Configuration SET UP MENU 14 External Control esses 16 About the external control 16 Using the MAKE TRIGGER system 17 Using the serial communication 1
23. anada and AC 220 240 V For For European and Asian countries AC 220 240 V European countries Asian countries and United Kingdom The power cord attached conforms to the following power supply voltage and countries Use only the power cord designated to ensure safety and EMC regulations of each country Not all types of power cords are supplied to this product For U S A and Canada For United Kingdom AC 120 V AC 220 240 V sp di cr 4 This plug will fit only into a grounded power outlet If you are unable to insert the plug into the outlet contact your electrician to install the proper outlet Do not defeat the safety purpose of the grounded plug This product should be operated only with the type of power source indicated on the label If you are not sure of the type of power supply of your home consult your product dealer or local electric power company Warning Do not use the same power cord for AC 120 V as for AC 220 240 V Doing so may cause malfunction electric shock or fire Note for United Kingdom power cord only The plug of United Kingdom power cord has a built in fuse When replacing the fuse be sure to use only a correctly rated approved type re fit the fuse cover Consult your dealer or qualified personnel How to replace the fuse Open the fuse compartment with the blade screwdriver and replace the fuse Warning This is a class A product In a domestic environment th
24. ctivated Turning on off on standby the monitor Displaying the SET UP MENU by pressing 1 button while holding V button and turning CONTROL LOCK to OFF Operating the monitor by an external control If you try other operations wOControl lock on appears on the screen Restores all the settings and adjustments of the monitor to the default HOUR METER and the settings done by using the adjustment knobs on the front panel will not be reset When you operate the monitor with the AC power supply the monitor is turned off on standby then turned on automatically When you operate the monitor with the DC 12 V power supply the monitor is turned off on standby 15 External Control About the external control This monitor has three external control terminals MAKE TRIGGER terminal RJ 45 The following external control systems are available 1 MAKE make contact system Controls the monitor by short circuiting the corresponding pin terminal to the GND pin terminal or disconnecting opening it 2 TRIGGER trigger system Controls the monitor by sending the pulse signal instantaneously to the corresponding pin terminal Using the MAKE TRIGGER system page 17 e RS 485 terminals RJ 45 Controls the monitor with the RS 485 system Using the serial communication on page 18 e RS 232C terminal D sub 9 pin Controls the monitor with the RS 232C system Using th
25. d you cannot change the assignment of these functions Settings for the information display of the monitor Item To do Setting value POSITION Select the position to show the information display v On the UPPER LOWER Information Display on page 7 SOURCE ID Select if the name assigned in CHARACTER SET is displayed on OFF ON the screen On the Information Display on page 7 CHARACTER SET Assign name to each video source as you like 10 characters at t NOTE maximum You can also enter a name using the RS 232C system STATUS DISPLAY Select if the status of the current input and the setting of muting are AUTO OFF ON displayed on the screen On the Status Display on page 7 CRC ERROR Select if the CRC error indication for the input HD SDI signal is displayed ON OFF on the screen s On the Information Display on page 7 SUB HOUR METER Display the hours of use unit hour You can reset this item MODEL Display the model name of the monitor VERSION Display the version of the monitor HOUR METER Display the total hours of use unit hour This item is used for maintenance of the monitor You cannot reset this item 1 Memorized for each input Setting value OFF ON Turns on or off the control lock function to disable the buttons on the front panel The following operations are available even when this function is a
26. dily while ON is selected select OFF While ON is selected the displayed picture may become unstable when an operation using buttons on the front panel or the menu is performed or when the signal format changes LOW LATENCY ON OFF When setting NO SYNC ACTION to GRAY B the screen color changes to gray and the power consumption of the back light is saved by half Selecting P SAVE power save mode saves more power consumption by turning off the back light 13 Menu Configuration SET UP MENU For the operation procedure see page 7 rr I MENU ee MENU Q CONTRAST 00 RI lt SET UP MENU gt gt FUNCTION SETTING PICTURE SUB ADJ lt FUNCTION SETTING gt gt sub menu POSI COLOR SYSTEM SIZE POSI ADJ TALLY SELECT GREEN WHITE BALANCE SET SD4 3 LARGE 0 REMOTE SETTING INFORMATION lt PICTURE SUB ADJ gt CONTROL LOCK OFF gt Q CONTRAST 00 38 BRIGHT 00 SELECT 8 EXIT MENU CHROMA 00 wa PHASE 00 NTSC SET um o COMPO 4 sub menu COMPO LEVEL reset Operation guide Shows the buttons for each operation reset gt Q Are you sure YES then gt NO then MENU lt SIZE POSI ADJ gt
27. djustment knob 9 PHASE Adjusts the picture hue CHROMA Adjusts the picture color density BRIGHT Adjusts the picture brightness CONTRAST Adjusts the picture contrast MUTING button Turns off the sound when no menu screen is displayed To cancel the function press the button again or turn the VOLUME adjustment knob Muting function is also canceled when BALANCE of AUDIO SETTING in the MAIN MENU is changed page 12 Select the style of the area marker in MARKER of the MAIN MENU page 11 This function works only when displaying the picture in 16 9 aspect ratio This function does not work when AREA MARKER or R AREA MARKER is set to OFF in MARKER SAFETY MARKER button lamp Displays hides the safety marker Adjust the area of the safety marker in MARKER of the MAIN MENU page 11 This function does not work when displaying the picture in the 1 1 mode This function does not work when SAFETY MARKER or R SAFETY MARKER is set to OFF in MARKER time code contained in the SDI signal On the Information Display on page 7 INPUT SELECT buttons lamps Selects an input SDI 1 E AUDIO HD SD SDI IN 1 terminal SDI 2 E AUDIO HD SD SDI IN 2 terminal DVI DVI D HDCP terminal COMPO COMPO terminal VIDEO VIDEO terminal The lamp for the selected input lights DC switch on the rear pan
28. e Deactivate the muting function 6 appear on the menu input signal No sound Connect the signal cable firmly 8 The items controlled by the MAKE system do not appear on the 17 Turn on the power of the connected component and set the output menu correctly Set CONTROL the SET UP MENU to OFF 15 OTHERS or Out of Check whathsi the inputsianal formatis acceniable cniih monitor 7 9 es monitor You cannot use the buttons for the items controlled by the MAKE 16 17 range appears put sig p system Disable the external control Select the correct input using the INPUT SELECT buttons 6 Connect the signal cable firmly 8 rf Turn on the power of the connected component and output video MO NAE qe ucc signals Or check whether the video output of the component video output setting of the VCR or graphic board of the computer is set correctly Adjust each picture adjustment knob on the front panel or adjust the 6 14 items of PICTURE SUB ADJ in the SET UP MENU Or perform reset in PICTURE SUB ADJ Check whether the setting of COLOR OFF or SCREENS CHECK 6 Wrong color no color buttons are appropriate Select the proper color system COLOR SYSTEM in FUNCTION 14 SETTING of the SET UP MENU Adjust the items of WHITE BALANCE SET in the SET UP MENU 14 Or perform reset in WHITE BALANCE SET The following are not malfunctions Whe
29. e into the pixel numbers of the monitor display Fit the vertical picture size into that of the monitor display ON C DE fh gt 14 FUNCTION SETTING Setting for the sub menu display color system color of the tally lamp and the picture size Item To do Setting value sub menu POSI Select the contents and displaying position of sub menu t NOTE COLOR Select the color system AUTO NTSC PAL SYSTEM If the picture is unstable with AUTO select PAL or NTSC TALLY SELECT Select the color of the tally lamp GREEN RED SD4 3 LARGE Change the picture size of 4 3 format signal te NOTE PICTURE SUB ADJ Adjusts the standard level for the picture adjustment and selects the set up level for the input video signal Item To do Setting value CONTRAST Adjust the standard level for the contrast adjusted 20 20 with CONTRAST knob on the front panel BRIGHT Adjust the standard level for the brightness 20 20 adjusted with BRIGHT knob on the front panel CHROMA Adjust the standard level for the chroma adjusted 20 20 with CHROMA knob on the front panel PHASE Adjust the standard level for the phase adjusted 20 20 with PHASE knob on the front panel NTSC SETUP Select the set up level of the input NTSC signal 00 compliant with 0 set up signal 7 5 compliant with 7 5 set up signal COMPO S
30. e serial communication on page 18 Set the following items of REMOTE SETTING in SET UP MENU according to the external control terminal and control system SERIAL TYPE PARALLEL TYPE on page 15 The settings of this unit Gontrol terminal Control system SERIAL setting PARALLELTYPE setting MAKE TRIGGER MAKE MAKE terminal TRIGGER TRIGGER RS 485 terminal Serial RS 485 RS485 RS 232C terminal communication RS 232C RS232C For a monitor connected to a personal computer etc select the terminal the equipment is actually connected to For other monitors select RS485 16 Control priority is as follows MAKE gt TRIGGER serial communication buttons and menu on the monitor You can use the external control even when CONTROL LOCK is set to ON page 15 When the monitor is off on standby external control is not available But certain external controls starting terminating communication turning on the monitor are available through the serial communication page 18 MAKE TRIGGER system You can control the monitor by a personal computer or dedicated controller 2 For the details see page 17 The controller is not commercially available Consult your dealer if you need it Serial communication RS 485 IN RS 485 RS 485 RS 485 RS 485 RS 485 or OUT IN OUT IN OUT RS 232C For
31. ed To display the safety marker for the area of a picture displayed in 16 9 aspect ratio hide the area marker i NOTE Memorized for each input 2 Not displayed when picture is displayed in the 1 1 mode 3 Displayed only when picture is displayed in 16 9 aspect ratio 11 Menu Configuration MAIN MENU cont MENU X MAIN MENU gt lt AUDIO SETTING gt lt LEVEL METER SETTING gt PICTURE FUNCTION gt BALANCE 10 gt LEVEL METER ch OFF BACK LIGHT 100 E AUDIO GROUP 1G BAR TYPE 3COLORS DVI INPUT SEL AUTO LEVEL METER SETTING REFERENCE LEVEL 20dB MARKER OVER LEVEL 10dB gt AUDIO SETTING WAVE FORM SETTING SYNC FUNCTION BAR BRIGHTNESS LOW ENTER gt SELECT EXIT IMENU Adjustment bar Displayed when selecting Operation guide BALANCE Shows the buttons for each operation The menu automatically disappears in about 30 seconds after the previous operation Some items may not appear on the menu depending on the input or the input signal The items controlled by the MAKE system do not appear on the menu NOTE Settings of E AUDIO GROUP The setting values and selectable audio channels of EMBEDDED AUDIO signals are as follows channel s 1 2 3 4 1 2 3 4 1 4 1G channel s 5 6 7 8 5 6 7 8 5 8 2G channel s 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 4 1G 5 8 2G 1 8 1G 2G channel s 9 10
32. ed by the manufacturer or Sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus 16 Batteries shall not be exposed to excessive heat such as sunshine fire or the like 17 When discarding batteries environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly European Union only Dear Customer This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety European representative of Victor Company of Japan Limited is JVC Technical Services Europe GmbH Postfach 10 05 04 61145 Friedberg Germany Information for Users on Disposal of Old Equipment European Union This sy
33. el before replacing the battery The length of time that the lamp lights in orange differs depending on the type of battery or the battery condition It is recommended to replace the battery when the lamp turns to orange Menu Operations 7 Display the menu To display the MAIN MENU Press MENU button To display the SET UP MENU Press lt button while holding V button MAIN MENU lt MAIN MENU gt PICTURE FUNCTION BACK LIGHT 00 INPIJT SEL AUTO Selected item T MARKER AUUTU SETTING WAVE FORM SETTING SYNC FUNCTION Operation guide SET UP MENU lt SET UP MENU gt FUNCTION SETTING p R B AD Selected item REMOTE SETTING INFORMATION CONTROL LOCK all reset Operation guide 2 Press V buttons to select an item then press gt button For some items adjustments will be made by pressing OC lt MARKER gt 1 2 gt AREA MARKER MARKER ASPECT SAFETY MARKER SAFETY AREA CENTER MARKER LINE BRIGHTNESS Ex When MARKER in the MAIN MENU is selected 3 Press V buttons to select an item then press lt buttons to make adjustments 4 Press MENU button to finish the menu operation Pressing MENU button repeatedly deactivates the display of the menu Audio Channel Selection Select audio channels emitted from the speakers L R and the AUDIO MONITOR OUT OUT1 L OUT2 R terminals EMBEDDED AUDIO signals come i
34. elect the level of the analog component signal B75 compliant with BetacamVTR 7 596 set up LEVEL 480i and 576i only signal BOO compliant with BetacamVTR 0 set up signal SMPTE compliant with M2VTR signals sub menu Display the sub menu which enables you to adjust the items in PICTURE SUB ADJ while viewing the actual picture reset Restore the default settings for all the items in PICTURE SUB ADJ Memorized for each input SIZE POSI ADJ Adjusts the size and position of the picture Item To do H SIZE 2 Adjust the horizontal picture size Setting value H POSITION Adjust the horizontal picture position Setting value varies depending on V SIZE Adjust the vertical picture size the signals V POSITION Adjust the vertical picture position sub menu Display the sub menu which enables you to adjust the items of SIZE POSI while viewing the actual picture reset Restore the default settings for all the items in SIZE POSI ADJ 2 Memorized for each signal format WHITE BALANCE SET Selects the color temperature and adjusts the drive level and cutoff point of each color R G B Item To do Setting value COLOR TEMP Select the color temperature 9300K 6500K USER R DRIVE G DRIVE Agjust the drive level of each color red green and blue MIN 000 MAX in 256 grades B DRIVE R CUT OFF G CUT OFF B CUT OFF Adju
35. he AC power supply is cut off for example when turning off the POWER switch the power supply automatically switches to the DC 12 V power supply DC switch Turns the DC 12 V power on or off You need to press 5 button 17 on page 6 on the front panel to turn on the monitor after turning on the DC switch The monitor consumes the battery even while the monitor is on standby To save battery life turn off the DC switch AC IN terminal AC power input connector Connect the provided AC power cord to an AC outlet Attach the provided power cord holder to prevent accidental disconnection of the AC power cord Attaching the power cord holder on page 9 8 2 POWER switch Turns AC power on or off You need to press 5 button 17 on page 6 to use the monitor after turning on the POWER Switch 3 Screw holes for external battery attachment Attach external battery for DC 12 V power supply by using 2 screw holes Choose the appropriate screw holes from 1 2 3 or 4 according to the type of external battery Use the Anton Bauer Dionic 90 mount QR DXC external battery CAUTION Do not use the external battery for DC 24 V power supply Use only the battery specified above If a heavy battery is used it may fall off depending on the way the monitor is used When an external battery is attached attach the ferrite core pr
36. icture may change depending on the input signal AREA MARKER button lamp Displays hides the area marker to 16 9 when the picture of 16 9 aspect ratio is squeezed into 4 3 format signal To return to 4 3 press the button again This function does not work when displaying the picture in the 1 1 mode 13 WAVE FORM button lamp Displays hides the indication of the wave form 18 monitor Adjust the settings of the wave form monitor in WAVE FORM SETTING of the MAIN MENU page 13 14 T C time code button lamp Activates deactivates the display of the time data Turns on and off on standby the monitor The power switches the POWER switch and DC switch are equipped on the rear panel of the monitor rs 10 12 on page 8 To turn off the monitor completely turn off the POWER switch and DC switch DC lamp When the DC 12 V power voltage is being lowered due to the battery consumption the lamp changes to orange from green When the voltage becomes lower than a certain level the monitor automatically turns off and the lamp turns to red Make sure to turn off the POWER switch and 1 Speakers stereo The speakers emit the same audio signal emitted from the AUDIO MONITOR OUT terminals 8 5 AUDIO MONITOR OUT terminals on page 8 2 VOLUME adjustment knob Adjusts the volume 3 Picture a
37. input signal The items controlled by the MAKE system do not appear on the menu NOTE Setting of CHARACTER SET Assign a name for each video source 1 Change the input to one that you want to assign a video source name for 2 Select CHARACTER SET 3 Press V buttons to select the first character Each time you press A button the character changes as follows Press V button to reverse the order 0 9 A Z a z lt CHARACTER SET gt amp lt gt _ 4 Press button to move the arrow to the next space The characters entered before moving the arrow are memorized 5 Repeat steps 3 and 4 10 characters at maximum B Press MENU button to store the name lt CHARACTER SET REMOTE SETTING External Control on pages 16 to 18 Settings for the external control Item To do Setting value SERIAL TYPE Select the input terminal used for external control by RS232C RS485 serial communication PARALLEL TYPE Select the external control method for the MAKE MAKE TRIGGER SET TRIGGER terminal PIN1 PIN2 PIN3 Assign the control functions to the pins of the MAKE Functions controlled by the MAKE PIN4 PINS TRIGGER terminal TRIGGER system on page 17 INFORMATION Assign a function to each pin terminal by selecting SET in PARALLEL TYPE mentioned above The functions are assigned for PIN6 PIN8 an
38. is product may cause radio interference in which case the user may be required to take adequate measures Before connecting other products such as VCR s and personal computers you should turn off the power of this product for protection against electric shock Do not use attachments not recommended by the manufacturer as they may be hazardous When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or equivalents Unauthorized substitutions may result in fire electric shock or other hazards Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition Under the following conditions 1 Turn off the power 2 Unplug this product from the wall outlet 3 Refer service to qualified service personnel a When the product emits smoke or unusual smell b When the product exhibits a distinct change in performance for example no picture or no Sound If liquid has been spilled or objects have fallen on the product e If the product has been dropped or damaged in any way f When the power supply cord or plug is damaged Do not install this product in the following places in a damp or dusty room where the product is exposed to soot or steam such as near the cooking counter or a humidifier near heat sources
39. lled with the MAKE system You cannot assign the same function to different pin terminals The TRIGGER system switches each function by short circuiting the pin terminal for about 1 second and opening it 17 External Control cont Using the serial communication You can control the monitor from a personal computer etc via the RS 485 or RS 232C terminal Consult your dealer for the details of the external control specification lt Communication specifications gt Terminal Input terminal specification Communication specifications RS 485 RS 232C A straight LAN cable A straight cable with a D sub 9 pin connector male for the monitor Parity No parity female for the personal computer Stop Bits 1 bit etc Flow Control No control Communication Code ASCII Code Baud Rate 4800 bps Data Bits 8 bits t See below lt Specifications of the RS 485 terminal gt lt Specifications of the RS 232C terminal gt 2 1 2 5 This is a female terminal 8 Thisis a female terminal 8 5 Pin No IN terminal signal OUT terminal signal Pin No Signal 1 TXD TXD 1 NC 2 TXD TXD 2 RXD 3 RXD RXD 3 TXD 4 NC NC 4 NC 5 NC NC 5 GND 6 RXD RXD 6 NC 7 NC NC 7 RTS 8 GND GND 8 CTS 9 NC The 7th terminal and the 8th terminal are connected Command outline All commands consist of the following segment
40. log signal then emitted is emitted only when SDI 1 or SDI 2 is selected and when EMBEDDED AUDIO signals come in to the E AUDIO HD SD SDI IN 1 or IN 2 terminal E AUDIO HD SD SDI IN 1 IN 2 terminals BNC Input terminals for the HD SD SDI signals The terminals accept also EMBEDDED AUDIO signals including up to 12 audio channels with a sampling frequency of 48 kHz N E AUDIO HD SD SDI SWITCHED OUT terminal BNC Output terminal for the HD SD SDI signals The SDI signals of the current input SDI 1 or SDI 2 are re clocked then emitted When an input other than SDI 1 and SDI 2 is selected the SDI signal of the input selected last time is emitted from this terminal The signals are emitted from this terminal only when the monitor is on or in PSAVE power save mode DVI D HDCP terminal Input terminal for the DVI D signal compatible with HDCP When the picture is not displayed correctly change the setting of DVI INPUT SEL 10 DC IN 12V terminal y LX DC 12 V maximum GNIS eT S DC 17 V power input js D MELOS connector When using DC 12 V power maximum DC 17 V check the DC IN 12V terminal pin signal and use the correct polarity If the polarity is reversed this could cause a fire or personal injury While using both the AC and DC 12 V power supply AC power supply is preferentially used If t
41. mbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end of life Instead the product should be handed over to the applicable collection point for the recycling of electrical and electronic equipment for proper treatment recovery and recycling in accordance with your national legislation Attention This symbol is only valid in the European Union By disposing of this product correctly you will help to conserve natural resources and will help prevent potential negative effects on the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more information about collection point and recycling of this product please contact your local municipal office your household waste disposal service or the shop where you purchased the product Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation Business users If you wish to dispose of this product please visit our web page www jvc europe com to obtain information about the take back of the product Other Countries outside the European Union If you wish to dispose of this product please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment EMC Supplement This equipment is in conformity with the provi
42. monitor 1 lower right 2 lower left 3 upper left 4 upper right FILTER Activates deactivates the low pass filter for the FLAT no filter LOWPASS incoming wave form data GAIN Adjust the gain level for the incoming wave form 10 10 data OVER LEVEL Select the over level for the incoming luminance NOTE signals MARKING Activates deactivates the function to change the OFF ON color of a wave form when the signal exceeds the limit specified on LEVEL vx below LEVEL Adjust the lower limit for the luminance signal 070 109 AUTO OFF Activates deactivates the function to make the ON OFF wave form monitor indication go off automatically 15 minutes after displaying it 1 This function does not work for the signals as follows RGB input signals digital DVI signals digital inputted from personal computer 1080 60p analog digital 1080 50p analog digital 640 480 60p analog digital SYNC FUNCTION Settings for the synchronization with signals Item To do Setting value NO SYNC ACTION Select the screen status when no signal is OFF coming in P SAVE power save mode GRAY B gray screen DELAY TIME Select the period until the screen status 30sec 5min 15min changes as selected in NO SYNC ACTION after signals stop coming in Activates deactivates the function to shorten the time taken to display the picture low latency function If the picture is not displayed stea
43. n a still image is displayed for a long time it may remain indistinctly on the screen after the picture has changed Though the remaining picture will disappear after a while there may be a case that it remains for a long period depending on the length of time the still image was displayed for This is due to the characteristics of the LCD display and is not a malfunction Red spots blue spots and green spots on the panel surface are a normal characteristic of LCD displays and not a problem The LCD display is built with very high precision technology however be aware that a few pixels may be missing or constantly lit The following symptoms are problems only when pictures or sounds are not played back normally A slight electric shock occurs when you touch the monitor The top and or rear panel of the monitor becomes hot The monitor emits a cracking noise The monitor emits a mechanical noise Maintenance Troubleshooting cont Self check program This monitor has a self check function which allows it to detect malfunctions and alert you This makes troubleshooting easier Whenever a problem occurs one or some of the INPUT SELECT lamps will flash If this happens follow the steps below and contact your dealer to resolve the problem COMPO VIDEO When the screen goes blank and one or some of the INPUT SELECT lamps DVI COMPO VIDEO on the front control panel start flashing 1 Check which lamps
44. n to the E AUDIO HD SD SDI terminal IN1 or IN2 and SDI input 1 or 2 is selected You have to choose a group of selectable audio channels before the channel selection E AUDIO GROUP in AUDIO SETTING on page 12 The setting is memorized for each input SDI 1 and SDI 2 1 Press lt or gt button when a menu is not displayed The screen for audio channel selection is displayed The screen for audio channel selection automatically disappears in about 30 seconds after the previous operation Audio channel selection screen Selected item E AUDIO R ch 2 2 Press 7 buttons to select the left L ch or right R ch 3 Press ac buttons to select audio channel Each time you press the button the audio channel changes according to the settings of E AUDIO GROUP NOTE on page 12 4 Press MENU button The screen for audio channel selection disappears Using the audio level meter You can check the conditions of the current EMBEDDED AUDIO signals in the audio level meter On the Information Display on the right LEVEL METER SETTING in AUDIO SETTING on page 12 On the Information Display The monitor displays the information below Make the setting to display hide each information using the MENU with the exception of 5 controlled with T C button 14 on page 6 Select the position of the information display POSITION in INFOR
45. ndby Selects SDI 1 input Selects SDI 2 input Selects DVI input Selects COMPO input Selects VIDEO input Cr Displays the status No data T E x x Cr Turns muting on off 00 Off 01 On Changes the aspect ratio 00 4 3 01 16 9 Cr is ODh The commands for starting communication connection No 1 terminating communication termination No 2 and turning on the monitor No 13 can be used while the monitor is off on standby UJ No data 9 No data No data No data No data No data No data No data No data No data No data No data No data O u vujo jic z U2 UJ U2 U2 U2 U2 U2 UJ E P D D E Ww Ww N N N N N S 14 UJ gt Enter the monitor s ID for The initial setting of the monitor s ID is 00 When connecting several monitors 00 is a command for controlling all monitors at once 2 Enter the appropriate data to 3 Displays the information shown when the INPUT SELECT button currently lit is pressed On the Status Display on page 7 Troubleshooting Solutions to common problems related to the monitor are described here If none of the solutions presented here solve the problem unplug the monitor and consult an authorized dealer or service center Symptom Probable
46. ng pin terminal to the 8th pin terminal GND or opening it When the TRIGGER system is selected Operate each function by pulse control that is short circuiting the corresponding pin terminal to the 8th pin terminal GND for about 1 second and opening it When changing the input with MAKE system only one pin terminal must be short circuited Other pin terminals must be opened When selecting the TRIGGER system you can operate only one function at a time Operate the functions one by one Functions controlled by the MAKE TRIGGER system Display Functions to be controlled Opening Short circuiting Selects the color of the tally lamp Green Red Changes the input to SDI 1 Invalid Valid Changes the input to SDI 2 Invalid Valid Changes the input to DVI Changes the input to COMPO Invalid Invalid Valid Changes the input to VIDEO Invalid The area marker indication The safety marker indication Off Off Indication of the area of the specified aspect ratio Off The center marker indication Off Selects the items of MARKER Non R items R items Changes the aspect ratio 4 3 16 9 Displays in 1 1 mode Off On Status display 4 t On the Status Display on page 7 Audio level meter display 5 Time code display Off On t SOURCE ID in I
47. oid the deterioration or damages of the cabinet such as its paint s peeling away be careful about the following Do not wipe the cabinet using solvent such as alcohol thinner or benzine Do not expose the cabinet to any volatile substance such as insecticides Do not allow any rubber or plastic in contact for a long time Do not wipe the cabinet forcefully Wipe stains off the cabinet with a soft cloth If the cabinet gets heavily stained wipe it with a soft cloth soaked in water diluted neutral detergent and wrung well then wipe with a soft dry cloth Ventilation openings Use a vacuum cleaner to get rid of the dust around the intakes all the openings If a vacuum cleaner is not available use a cloth and wipe it off Leaving the dust around the intakes may prevent proper temperature control and cause damage to the product Specifications General minput output terminals Model name DT V17L3D Type Multi format LCD monitor Screen size Type 17 wide format Aspect ratio 16 10 LCD panel 17 wide active matrix TFT Effective screen size Width 367 2 mm 14 7 1 6 COMPO Y Ps B Y Pr R Y Height 229 5 mm 97 Y Pe B Y Input output of composite signal 1 line BNC connector x 2 1 V p p 75 The input IN and output OUT terminals are bridge connected auto termination DVI D HDCP DVI D signal input compatible with HDCP DVI D connector x 1 compatible with DDC2B Input output of analog component
48. ovided to the power cord from the mount as illustrated below Ex When the Anton Bauer mount QR DXC M3A is used Ferrite core 4 Security slot Attach a security wire to this slot Note for connections Before making any connections turn off all the equipment Use a cord whose plugs correctly match the terminals on this monitor and the equipment Plugs should be firmly inserted poor connections could cause noise When unplugging a cord be sure to grasp its plug and pull it out DO NOT connect the power cord until all connections are complete Refer also to the user manual of each piece of equipment Computer signals preset DVI D HDCP terminals B Available signals The following signals are available for this monitor Resolution Frequency Video signals ib c Horizontal Vertical Horizontal kHz Vertical Hz system Signal format Input terminal 1 AL No Signalname Shown in the COMPO E AUDIO HD DVI D HDCP M ieee Non inter status display Analog SD SDI Digital component 3 SVGAe0 Nori inter page 7 component digital RGB 4 XGA60 Non inter 1 NTSC 5 WXGA 1280 Non inter 2 PAL 6 WXGA 60 Non inter 3 B W50 7 SXGA60 4 Non inter 4 B W60 8 WSXGA 60 4 Non inter 5 480 60i UXGA60 4 Non inter 6 576 50i WUX
49. s Header Monitor ID Command ID Function Data Cr ODH On Header I Operation commands from the personal computer etc For details see Basic command list on the right 2 Reference commands from the personal computer etc Status returns from the monitor To start communication send the connection command from the personal computer etc To terminate the communication send the termination command from the personal computer etc 18 Example of communication procedures Starting the communication connection command 00BCN1Cr Monitors status OOBOKCr Monitor Selecting SDI 1 input 100 Monitor s status OOBOKCr 5 the communication termination command IOOBCNOCT amp Monitors status OOBOKCr PC etc Basic command list i c c ME Starts communication connection No data Terminates communication termination Assigns the control ID Initializes the control ID No data 01 99 00 Hide 01 Display 00 Hide 01 Display www UJ W Displays hides the ID Flashes hides the selected ID No of the monitor Displays the MAIN MENU Quits the menu operation Moves the cursor upward A Moves the cursor downward V Makes setting adjustment gt Makes setting adjustment lt Displays the SET UP MENU Turns on the monitor Turns off the monitor on sta
50. s controlled by the MAKE system do not appear on the menu PICTURE FUNCTION Setting for the picture quality 10 Item To do Setting value APERTURE Select the frequency of the luminance signal compensated in OFF LOW HIGH FREQ APERTURE LEVEL APERTURE Compensate the frequency response of the luminance signal of the 01 10 LEVEL video signal CTI Adjust the clearness of the outlines of the chrominance signal OFF NORMAL HARD LTI Adjust the clearness of the outlines of the luminance signal OFF NORMAL HARD MODE Selects a proper mode corresponding to the input picture NORMAL CINEMA FIELD sub menu Display the sub menu which enables you to adjust the items of PICTURE FUNCTION while viewing the actual picture reset Restore the default settings for all the items in PICTURE FUNCTION Memorized for each input BACK LIGHT Setting value 20 20 Adjusts the brightness of the display Setting value AUTO MODE1 MODE2 MODE3 When AUTO is selected the format of signals come to the DVI D HDCP terminal is automatically recognized Normally select AUTO Select MODE1 MODE2 or MODE when the picture is not displayed correctly with AUTO DVI D input of the monitor is compatible with HDCP MENU lt MAIN MENU gt lt MARKER gt 1 2 gt PICTURE FUNCTION gt AREA MARKER OFF
51. sions and protection requirements of the corresponding European Directives This equipment is designed for professional video appliances and can be used in the following environments Controlled EMC environment for example purpose built broadcasting or recording studio and rural outdoors environment far away from railways transmitters overhead power lines etc In order to keep the best performance and ensure electromagnetic compatibility we recommend to use cables not exceeding the following length Cable Length Power cord 2 0m attached cable HO5VV F x 0 75 mm Video signal cable coaxial cable 2 0m Audio signal cable shielded cable 1 5m DVI cable shielded cable 2 0m RS 232C cable shielded cable 2 0m A straight cable with a D sub 9 pin connector RS 485 cable twist pair cable 2 0m A straight LAN cable REMOTE cable twist pair cable 2 0m A straight LAN cable The inrush current of this apparatus is 8 947 ampere CAUTION In case where the strong electromagnetic waves or magnetism are near the audio cable or the signal cable the sound or the picture will contain noise In such cases please keep the cable away from the sources of the disturbance Installation CAUTION Do not rest your arm on the monitor or lean against the monitor Do not touch the LCD panel when installing the monitor Be sure to install the monitor securely to prevent the monitor from falling over which may
52. sition Stand plate Stand body S To prevent an accidental fall Fix the monitor to a wall by using strings Fixing the monitor Attach the hook not provided to the VESA mounting holes on the rear panel use the two holes on the upper side using M4 x 10 mm screws not provided Bind the hooks on the rear panel of the monitor to a wall or a pillar using durable string VESA mounting holes Hook and screw M4 x 10 mm not provided Hook not provided Daily Operations Connections m Front panel NO EFFECT is displayed when you press a button which is not available for the current input or signal format the lamp lights even when the function does not Tally lamp actually work This lamp is controlled by the tally function of the The items controlled by the MAKE system cannot be controlled by the buttons on the front panel REMOTE ON is displayed and the lamps do not light MAKE TRIGGER terminal 4 16 17 You can select the color of the tally lamp from GREEN or RED TALLY SELECT in FUNCTION SETTING on page 14 and External Control on page 16 PHASE CHROMA BRIGHT CONTRAST AREA SAFETY 3 MUTING o 1 2 DV COMPO VIDEO INPUT SELECT Wwe
53. st the cutoff point of each color red green and blue MIN 000 MAX in 256 grades sub menu Display the sub menu which enables you to adjust the items in WHITE BALANCE SET while viewing the actual picture reset Restore the default settings for the drive levels and cutoff points of the selected color temperature 3 Memorized for each color temperature MENU lt REMOTE SETTING gt lt SET UP MENU gt gt FUNCTION SETTING gt SERIAL TYPE RS2320 PICTURE SUB ADJ PARALLEL TYPE MAKE SIZE POSI ADJ PINI m WHITE BALANCE SET PIN2 DM REMOTE SETTING PIN3 INFORMATION PIM MG CONTROL LOCK PINS MEAS n all reset TALLY ENTER SELECT EXIT MENU uH oe Operation guide Shows the buttons for each operation lt INFORMATION gt lt CHARACTER SET gt gt POSITION UPPER SOURCE ID OFF CHARACTER SET STATUS DISPLAY AUTO CRC ERROR ON 00001H P D lt reset gt SUB HOUR METER MODEL DT VI7L3D A Are you sure VERSION YES then key HOUR METER 00001H NO then MENU key all reset gt A Are you sure YES then gt key NO then MENU key The menu automatically disappears in about 30 seconds after the previous operation Some items may not appear on the menu depending on the input or the
54. the details see page 18 m Using the MAKE TRIGGER system The MAKE TRIGGER terminal is configured as follows You can assign a function to each pin terminal in REMOTE SETTING PIN1 PIN2 PIN3 PIN4 PIN5 in PARALLEL on page 15 You cannot change the functions assigned to the pin terminals from 6th to 8th Pin No Pin name 1 PIN1 2 PIN2 3 PIN3 This is a female terminal 4 PIN4 5 PIN5 6 PIN6 TALLY 7 PIN7 ENABLE 2 8 PIN8 GND The 6th pin terminal controls turning on or off the tally lamp available to control even when the 7th pin terminal is invalid 2 The 7th pin terminal makes the external control valid invalid Make sure to control the terminal by the MAKE system To assign the functions to the pin terminals For the operation procedure see page 7 1 Select REMOTE SETTING on the SET UP MENU 2 Set PARALLEL to SET 3 Select a pin name PIN1 PIN5 for which you want to assign a function then select the function you want to assign For selectable functions see the tables on the right Operation of the external control 1 Set PARALLEL TYPE of REMOTE SETTING to MAKE or TRIGGER the SET UP MENU 2 Short circuit the 7th pin terminal ENABLE to the 8th pin terminal GND so that the monitor can be controlled by the external control 3 When the MAKE system is selected Operate each function by short circuiting the correspondi
55. tice on transportation This monitor is precision equipment and needs dedicated packing material for transportation Never use any packing material supplied from sources other than JVC or JVC authorized dealers 21 Specifications cont B Dimensions urit mm inch Front view Side view Rear view 86 3 1 2 gt lt VESA mounting holes 40 1 5 8 Size 4 M4 depth 10 mm 395 15 5 8 1 5 1 16 100 lt gt gt X X l ee g 55895595 TERT ur ees n 80000006 J o pe 000 304 12 100 344 8 13 5 8 309 5 12 1 4 Ed E E o6 00000 6000 99 99 0 0000 yY 34 1 3 8 240 9 1 2 i A gt 199 77 8 atthe higher position at the lower position DT V17L3D MULTI FORMAT LCD MONITOR 2008 Victor Company of Japan Limited 0708STH MW VP
56. ustries Alliance http www eiae org WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE WARNING THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE EARTHING CONNECTION CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specifi
57. where condensation easily occurs such as near the window Do not place this product on an unstable cart stand or table The product may fall causing serious injury to a child or adult and serious damage to the product The product should be mounted according to the manufacturer s instructions and should use a mount recommended by the manufacturer Do not use this product near water Be sure to install the product in the place where proper temperature and humidity are kept Operating conditions on page 21 This product becomes hot during its use Take enough care when handling the product Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltages and other hazards Refer all service to qualified service personnel Do not use the product for a long time if the sound is distorted Use only the power source specified on the unit AC power 120 V 220 240 V 50 Hz 60 Hz DC power 12 17 V If the product has been exposed to rain or water The AC power supply is controlled by turning on off the POWER switch on the rear panel If the product is installed in a place where you cannot easily turn on off the POWER switch control the AC power supply by plugging unplugging the power cord into from the AC outlet In this case install the product as close to the AC outlet as possible and leave enough space for plugging unplugging the power cord
Download Pdf Manuals
Related Search