Hotpoint AQXL 169 User's Manual
Contents
1. 14 Hotpoint After Sales Service ES No one is better placed to care for your Hotpoint appliance during the course of its working life than us the manufacturer Essential Contact Information Hotpoint Service We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified engineers on call to ensure you receive fast reliable local service UK 08709 066 066 Republic of Ireland 0818 313 413 www hotpointservice co uk Please note Our advisors will require the following information Serial number Parts and Accessories We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life UK 08709 077 077 Republic of Ireland 0818 313 413 www hotpointservice co uk Appliance Registration We want to give you additional benefits of Hotpoint ownership To activate your free 5 year parts guarantee you must register your appliance with us UK 0870 6092094 Republic of Ireland 01 230 0800 www hotpointservice co uk Indesit Company UK Ltd Morley Way Peterborough PE2 9JB Indesit Company Unit 49 Airways Industrial Estate Dublin 17 Recycling amp Disposal Information As part of Hotpoint s continued commitment to helping the environment Hotpoint reserves the right to use quality recycled components to keep down2. button the tempe rature can be progressively reduced or even set to cold wash x By pressing the 9 button the spin speed can be progressively reduced or even eliminated altogether PX If the buttons are pressed again the maximum values are restored Exception if the Whites programme is selected the temperature can be increased up to a value of 90 C Ey Adjust the intensity of the wash The machine automatically selects the medium MED or minimum MIN level available for the set programme By pressing the button the user can increase or decrease the intensity of the wash this adjustment may prolong or shorten the cycle duration Exception it is not possible to increase the wash intensity for the Fast Wash Silk and Wool programmes wi ej Modify the cycle caracteristics Press the OPTION buttons to personalise the wash cycle according to your own requirements e Press the button to activate the option the corresponding indicator light will illuminate e Press the button again to deactivate the option the indicator light will switch off If the selected option is not compatible with the set programme the indicator light will flash and the option will not be activated If the selected option is not compatible with another previously selected option the indicator light corresponding to the first option will flash and only the second option will be activated the correspond
3. Make sure that the water level inside the machine is lower than the door opening if this is not the case remove excess water using the water outlet hose collecting it in a bucket as shown in the figure 3 Remove the covering panel on the front of the washing machine using a screwdriver see figure 4 Using the tab shown in the figure pull outwards until the plastic brace comes away pull it downwards until you hear a click which indicates that the door is unlocked 5 Open the door if this is still not possible repeat the process 6 Replace the cover panel making sure that the hooks are positioned in the right slots before pushing the panel towards the machine 11 Care and maintenance Shutting off the water and electricity supplies e Shut off the water tap after every wash This limits wear and tear on the machine s water supply and prevents leaks e Disconnect the appliance from the electricity supply before cleaning it and before performing any maintenance work on it Cleaning the machine The exterior of the appliance and all rubber parts may be cleaned using a cloth soaked in warm soapy water Do not use solvents or abrasive products Cleaning the detergent dispenser drawer To remove the drawer press the lever 1 and pull it outwards 2 see figure Wash the drawer under running water this should be done regularly Drum maintenance e Always leave the port
4. amp SYNTHETICS 40 40 o o 8 5 1 5 1h 10 1h5 AM e 2 85 15 30 3 Vigorous programmes a ow e e zs ss mom amp SYNTHETICS 60 60 o o 8 5 1 5 th 25 1h 10 Special programmes SHIRTS 40 o o 2 1 1h 15 1h 10 S gt SILK Washes silk and garments and lingerie 30 o o 2 1 55 50 WOOL Washes wool cashmere etc 40 o o 2 1 1h 5 1h 5 E2 DUVETS Washes garments filled with goose down 30 o o 3 1 5 1h15 1h 15 BED amp BATH Washes bathroom laundry and bedlinen 60 o o O 3 5 1h 55 1h 45 Partial programmes ty Durable rinse 7 5 3 5 45 40 ty Delicate rinse 3 5 1 5 40 35 Durable spin 20 Delicate spin 14 kp Drain 3 Wash options wi Super Wash This option guarantees a high performance wash thanks to the use of a greater quantity of water during the initial phase of the cycle and a longer overall duration of the programme It is not compatible with the Fast Wash Silk Wool Duvets and Partial programmes A Easy Iron If this option is selected the wash and spin phases will be adjusted accordingly so that fabric creasing is reduced At the end of the cycle the drum of the washing machine will spin slowly the Easy Iron and START PAUSE indicator lights will flash To end the cycle press the START RESET button or the Easy Iron button When using the Silk programme the machine will end the c
5. customer costs and minimise material wastage Please dispose of packaging and old appliances carefully To minimise the risk of injury to children remove the door plug and cut the mains cable off flush with the appliance Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains socket and the door cannot be locked shut 15 16 Hotpoint 195 052 806 00 June 2005
6. from 1 to 7 5 kg Electrical voltage 220 240 V 50 Hz connections maximum absorbed power 2100 W maximum pressure 1 MPa 10 bar Water connections minimum pressure 0 05 MPa 0 5 bar drum capacity 62 litres Spin speed up to 1600 rotations per minute Whites programme temperature 60 C Maximum wash intensity using a load of 7 5 kg Test programmes according to regulation IEC456 This appliance conforms to the following EC Directives 72 23 EEC dated 19 02 73 Low Voltage and subsequent modifications 89 336 EEC dated 03 05 89 E Electromagnetic Compatibility and subsequent modifications 2002 96 EC Hotpoint Description of the machine BZ Zz CONTROL PANEL DOOR DOOR HANDLE TOE KICK ADJUSTABLE FEET DOOR DETERGENT DISPENSER Always use the handle to open the door see diagram This is inside the machine and may be accessed by opening the door For information relating to detergents please refer to the chapter entitled Detergents and laundry 1 Pre wash compartment use powder detergent 2 Main wash compartment use powder or liquid detergent If you intend to use liquid detergent we recommend that it is poured into the compartment immediately before the wash cycle is started amp compartment for additives for fabric softener or other liquid washing additives Do not exceed the maximum level indicated by the grille and dilute conc
7. wash cycle does not begin The washing machine fails to load water The machine continuously loads and drains water The machine does not drain or spin The washing machine vibrates too much during the spin cycle The washing machine leaks The icons corresponding to the Phase in progress flash rapidly at the same time as the ON OFF indicator light There is too much foam The washing machine door remains locked Possible causes Solutions e The plug has not been inserted into the electrical socket or it has not been inserted far enough to make contact e There is no power in the house e The porthole door has not been shut properly e The START RESET button has not been pressed e The water tap has not been turned on e The water inlet hose is not connected to the tap e The hose is bent e The water tap has not been turned on e There is no water in the house e The water pressure is insufficient e The START RESET button has not been pressed e The end of the outlet hose has not been fitted at a height between 65 and 100 cm from the floor see Installation e The free end of the hose is underwater see Installation e f If the dwelling is on one of the upper floors of a building there may be problems relating to water drainage causing the washing machine to load and drain water continuously Special anti draining valves are available in shops and help to avoid this inconvenien
8. B Hotpoint Kitchen think Instructions for Installation and Use Washing machine Model AQXL 169 To the Installer Before installation fill in the product details on the back cover of this book The information can be found on the rating plate To the User You must read the instructions prior to installing and using the appliance and then retain them for future reference Instruction booklet WASHING MACHINE Contents EN Installation 2 3 4 5 EI Unpacking and levelling Connecting the water and electricity supplies English 1 Technical data Description of the machine 6 7 Control panel Running a wash cycle 8 Programmes and options 9 Table of Programmes Wash options Detergents and laundry 10 Detergent Preparing the laundry AQXL 169 Washing advice Load balancing system Precautions and tips 11 General safety Disposal Opening the door manually Care and maintenance 12 Shutting off the water and electricity supplies Cleaning the machine Cleaning the detergent dispenser Drum maintenance Cleaning the pump Checking the water inlet hose Troubleshooting 13 Assistance 14 B Hotpoint Installation Keep this instruction manual in a safe place for future reference If the appliance is sold given away or moved please ensure the manual remains with the machine so that the new owner may benefit from the advice contained within it Please read this instruction manual caref
9. ace over the edge of a basin or sink be sure the free end of the hose should not be underwater We advise against the use of hose extensions in case of absolute need the extension must have the same diameter as the original hose and must not exceed 150 cm in length Ensure that if the drain hose is pushed into a standpipe that the end does not go down more than 15cms 6 inches If the hose is pushed down too far this may cause the machine to self syphon ie continuously empty as it is filling Electric connection Before plugging the appliance into the mains socket make sure that e the socket is earthed and in compliance with the applicable law e the socket is able to sustain the appliance s maximum power load indicated in the Technical details table on the next page Hotpoint e the supply voltage is included within the values i ndicated on the Technical details table on the next page e the socket is compatible with the washing machine s plug If this is not the case replace the socket or the plug Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use Before using the appliance please read the instructions below WARNING THIS APPLIANCE MUST BE EARTHED THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN Replacing the fuse When replacing a faulty fuse a 13 amp ASTA approved fuse to BS 1362 should alway
10. any consumable item or accessory These include but are not limited to plugs cables batteries light bulbs fluorescent tubes and starters covers and filters Replacement of any removable parts made of glass or plastic THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON DOMESTIC PREMISES 5 Year Parts Guarantee Hotpoint also offers you a free 5 year parts guarantee This additional guarantee is conditional on you registering your appliance with us and the parts being fitted by one of our authorised engineers There will be a charge for our engineer s time To activate the extra parts warranty on your appliance simply call our registration line on 0870 6092094 ROI 01 230 0800 Extended Guarantees We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills for the life of your policy To find the ideal plan for you please call our advice line on 08709 088 088 ROI 01 230 0233 Free Helpdesk Service We have a dedicated team who can provide free advice and assistance with your appliance if you experience any technical difficulties within the first 90 days of ownership Simply call our Hotpoint Service Hotline on 08709 066 066 ROI 0818 313 413 for telephone assistance or where necessary to arrange for an engineer to call If we cannot resolve the technical problem we will replace your machine or if you prefer give you your money back
11. blem persists after the above checks have been carried out shut off the water tap switch off the machine and contact Assistance 13 Assistance cl Guarantee 12 Months Parts and Labour Guarantee Your appliance has the benefit of our manufacturer s guarantee which covers the cost of breakdown repairs for twelve months from the date of purchase This gives you the reassurance that if within that time your appliance is proven to be defective because of either workmanship or materials we will at our discretion either repair or replace the appliance at no cost to you This guarantee is subject to the following conditions The appliance has been installed and operated correctly and in accordance with our operating and maintenance instructions The appliance is used only on the electricity or gas supply printed on the rating plate The appliance has been used for normal domestic purposes only The appliance has not been altered serviced maintained dismantled or otherwise interfered with by any person not authorised by us Any repair work must be undertaken by us or our appointed agent Any parts removed during repair work or any appliance that is replaced become our property The appliance is used in the United Kingdom or Republic of Ireland The guarantee does not cover Damage resulting from transportation improper use neglect or interference or as a result of improper installation Replacement of
12. ce e The wall drainage system is not fitted with a breather pipe e The programme does not include a draining phase some programmes require manual draining see Programmes and options e The Easy Iron option is enabled to complete the programme press the START RESET button see Programmes and options e The outlet hose is bent see Installation e The drainage duct is clogged e The drum was not unlocked properly when the appliance was installed see Installation e The washing machine is not level see Installation e The washing machine is trapped between cabinets and a wall see Installation e The load is not balanced properly see Description of the machine e The water inlet hose is not screwed on to the tap correctly see Installation e The detergent dispenser drawer is blocked for instructions on how to clean it see Care and maintenance e The outlet hose has not been secured properly see Installation e Switch off the machine and unplug the appliance wait for approximately 1 minute then switch it on again If the problem persists contact Assistance e The detergent is not designed for machine washing the packaging should state that the product is for washing by machine for washing by hand or machine or similar e Too much detergent was used e Follow the manual unlocking procedure see Precautions and tips If the pro
13. cycle to avoid excessive vibrations and to distribute the load in a uniform manner the drum rotates continuously at a speed which is slightly faster than the normal washing speed If after several attempts the load is still not evenly distributed the machine spins at a lower speed than the set frequency f the load is excessively unbalanced the washing machine attempts to distribute it instead of spinning n order to achieve better load distribution and balance we recommend that large and small garments are mixed when placing the laundry in the machine Precautions and tips This machine was designed and manufactured in compliance with cuurent international safety standards The following advice is provided for safety reasons and should be read carefully General safety e This appliance was designed for domestic use inside the home and is not intended for commercial or industrial use e The washing machine must be used by adults only in accordance with the instructions provided in this booklet e Do not touch the machine when barefoot or with wet or damp hands or feet e When unplugging the appliance always pull the plug from the mains socket do not pull on the cable e Do not touch the drained water as it may reach extremely high temperatures e Never force the porthole door doing so may damage the safety lock mechanism designed to prevent the door being opened accidentally e If the appliance breaks down under
14. d much less likely to cause vibrations and noise during the spin cycle If positioned on a fitted carpet or a rug adjust the feet in such a way as to allow room for air to circulate and provide ventilation beneath the washing machine Connecting the water and electricity supplies Connecting the water inlet hose Before connecting the inlet hose to the water supply allow the water to flow from the tap until it runs clear 1 Connect the inlet hose to the machine by screwing it into the cold water inlet on the upper right hand side of the back of the machine see figure 2 Place the seal A provided in the bag on the end of the inlet hose and screw it to a cold water tap with a 3 4 gas threaded connection see figure 3 The hose should not be bent or compressed The water pressure at the tap must fall within the values indicated in the Technical data table see next page If the inlet hose is not long enough contact a specialist store or an authorised technician Always use the new inlet hoses supplied with the machine Connecting the drain hose 65 100 cm Connect the drain hose without bending it to a draining duct or a wall drain situated between 65 and 100 cm from the floor The drain hose may be connected to an under sink trap Before connecting the drain hose from the machine ensure that any blanks or removable ends have been taken off the spigot If it is pl
15. entrated fabric softeners Control panel Hotpoint OPTION WASH PROGRAMME buttons and CYCLE START PAUSE knob indicator lights PHASE button with indicator light ON OFF CANCEL button with indicator light TEMPERATURE button SPIN SPEED button ON OFF CANCEL button with indicator light press the button briefly to switch the machine on or off The green indicator light shows that the machine is switched on To switch the washing machine off during a wash cycle press and hold the button for approximately 2 seconds pressing the button quickly or accidentally will not switch the machine off If the machine is switched off during a wash cycle the programme will be cancelled PROGRAMME knob this can be rotated in both directions To set a more suitable programme please refer to the Table of Programmes The knob is locked into position during the wash cycle TEMPERATURE button press this button to adjust the temperature the value will be indicated by the indicator lights above it see Start up and personalisation SPIN SPEED button press this button to adjust the spin value or to exclude this part of the programme the value will be indicated by the indicator lights above it see Start up and personalisation INTENSITY Ey button press this button to adjust the wash intensity the value will be indicated by the indicator lights above it see Start up and personalisatio
16. hole door ajar to prevent unpleasant odours from forming Cleaning the pump The washing machine is fitted with a self cleaning pump which does not require regular maintenance However it may be that small objects coins buttons etc fall into the pre chamber that protects the pump the pump is located in the lower part of this pre chamber Make sure that the wash cycle has finished and remove the plug from the socket 12 To access the pre chamber 1 Remove the covering panel on the front of the machine using a screwdriver see figure 2 Position a container collecting the drained water approximately 1 5 correctly see figure 3 Unscrew the cover turning it in an anticlockwise direction see figure 4 Clean the inside thoroughly 5 Screw the cover back on 6 Replace the cover panel making sure that the hooks are positioned in the right slots before pushing the panel towards the machine Checking the water inlet hose Check the water inlet hose at least once a year If there are any cracks replace it immediately the high water pressure used by the wash cycles could cause a cracked hose to split open Troubleshooting Hotpoint From time to time your machine may not operate as it should Before calling for Assistance see Assistance make sure that the problem cannot be resolved easily using the following list Malfunction The washing machine will not switch on The
17. in elements that alter the balance of nature We recommend e the use of powder detergents for white cotton garments and for pre wash phases e the use of liquid detergents for delicate cotton garments and for all programmes which run at a low temperature e the use of liquid detergents for wool and silk Do not use detergents when washing garments by hand because they create too much foam The detergent must be measured out into the relevant compartment or into the detergent dosing ball which will be placed directly into the drum of the machine In this case the Cotton cycle with pre wash phase may not be selected Preparing the laundry Divide the laundry according to type of material the symbol on the garment label and colour making sure that whites are separated from coloured garments e Empty all pockets and check for loose buttons e Do not exceed the values indicated in the Table of Programmes which refer to the weight of the laundry items when they are dry How much does your laundry weigh 1 sheet 400 500 y 1 pillowcase 150 200 g 1 tablecloth 400 500 y 1 bathrobe 900 1200 y 1 towel 150 250 g 1 pair of jeans 400 500 g 1 shirt 150 200 g 10 Washing advice Shirts use a suitable programme to wash shirts made from different fabrics and in different colours This will guarantee that these garments are looked after properly Silk use the relevant programme designed for all silk gar
18. ing indicator light will remain lit in a fixed manner START THE PROGRAMME Press the START PAUSE button The corresponding indicator light remains lit in a fixed manner and the porthole door locks the DOOR LOCK indicator light illuminates The icons corresponding to the different wash phases will light up during the cycle indicating the phase in progress To change a programme while a cycle is in progress pause the washing machine by pressing the START PAUSE button then select the desired cycle and press the START PAUSE button again To open the door while a cycle is in progress press the START PAUSE button if the DOOR LOCK o indicator light switches off it is possible to open the door Press the START PAUSE button again to resatrt the programme from the point at which it was interrupted PROGRAMME END The text END lights up to indicate that the programme has ended The porthole door may be opened immediately If the START PAUSE button flashes press the button to end the cycle open the door unload the laundry and switch off the machine Programmes and options Table of Programmes Hotpoint Max Detergent en load Cycle duration Icon Programme description tempera 7 ture C Washing Es Normal Mint Normal Ain load load Everyday programmes WHITES ers 75 3 5 2h10 1h40 To COLOUREDS 40 o o 75 3 5 1h 35 1h 20
19. ments We recommend the use of a special detergent for delicate garments Curtains we recommend these are folded and placed inside a pillowcase or a mesh laundry bag Wash them separately making sure the half load weight is not exceeded and use the Silk programme as this automatically excludes the spin phase Wool Hotpoint is the only washing machine to have obtained the prestigious Woolmark Platinum Care mark of recognition M 0303 from The Woolmark Company which certifies the machine washing of all woollen garments even those whose label states hand wash only yay max 1 kg The Wool programme therefore offers you complete peace of mind when washing all woollen garments with great performance guaranteed every time Duvets we recommend this programme is used to wash laundry filled with goose down such as single or double duvets pillows wind jackets etc Use liquid detergent Once the laundry is dry shake it vigorously in order to distribute the filling evenly Bathroom laundry and bedlinen this washing machine can be used to wash any domestic laundry in a single cycle called Weekly washing that optimises the use of fabric softener while saving both time and electricity We recommend that you use a powder detergent Stubborn stains stubborn stains should be treated with solid soap before the garment is washed use the Cotton programme with pre wash phase Load balancing system Before every spin
20. n OPTION buttons and indicator lights may be used to select any of the available options The indicator light corresponding to the selected option will remain lit see Start up and personalisation ECO CHILD LOCK INTENSITY indicator button and indicator button light DOOR light LOCK indicator light WASH CYCLE PHASE icons these light up to provide an indication of the progress of the wash cycle Wash Rinse ty Spin Final draining phase kp The text END lights up when the cycle has finished START PAUSE button with indicator light when the green indicator light flashes slowly press the button to start the wash cycle When the cycle has started the indicator light is illuminated in a fixed manner To pause the wash cycle press the button again the indicator light will turn orange and begin to flash again If the Door Locked o indicator light is off the porthole door may be opened To restart the wash cycle from the point at which it was interrupted press the button again DOOR LOCKED gt indicator light this indicates that the porthole door is locked To open the door pause the wash cycle see following page CHILD LOCK button and indicator light this is used to enable or disable the Child lock function by pressing the button for approximately 2 seconds When the indicator light is illuminated the control panel is locked This avoids accidental changes being made
21. nect Brown wire to terminal marked L or coloured Red Connect Blue wire to terminal marked N or coloured Black If a 13 amp plug BS 1363 is used it must be fitted with a 13 amp fuse either in the plug or adaptor or at the distribution board If you are in any doubt the electrical supply to your machine consult a qualified electrician before use How to connect an alternative plug The wires in this mains lead are coloured in accordance with the following code BLUE NEUTRAL N BROWN LIVE L GREEN amp YELLOW EARTH E Disposing of the appliance When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above GREEN amp YELLOW gt CROSS BAR CORD GRIP The washing machine should not be installed in an outdoor environment not even when the area is sheltered because it may be very dangerous to leave it exposed to rain and thunderstorms When the washing machine is installed the mains socket must be within easy reach Do not use extensions or multiple sockets The power supply cable must never be bent or dangerously compressed The power supply cable must only be replaced by an authorised serviceman Warning The company denies all liability if and when these norms are not respected Technical data Model AQXL 169 width 59 5 cm Dimensions height 85 cm depth 64 5 cm Capacity
22. no circumatances must you attempt to carry out the repairs yourself e Keep children well away from the machine while it is in operation e f the machine must be moved work in a group of two or three people and handle it very carefully Never attempt to move the appliance without the help of another person because it is extremely heavy e Make sure that the drum is empty before loading laundry into the appliance Disposal e When disposing of the packaging material observe local legislation so that the packaging may be reused e The European Directive 2002 96 EC relating to Waste Electrical and Electronic Equipment states that household appliances should not be disposed of using the normal solid urban waste cycle Exhausted appliances should be collected separately in order to optimise the cost of re using and recycling the materials inside the machine while preventing potential damage to the atmosphere and to public health The crossed out dustbin is marked on all products to remind the owner of their obligations regarding separated waste collection For more information relating to the correct disposal of household appliances owners should contact their local authorities or appliance dealer Hotpoint Opening the porthole door manually ES If it is not possible to open the porthole door due to a powercut and you wish to hang out the laundry proceed as follows 1 Remove the plug from the electricity socket 2
23. s be used and the fuse cover re fitted If the fuse cover is lost the plug must not be used until a replacement is obtained Replacement fuse covers If a replacement fuse cover is fitted it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug Replacements can be obtained directly from your nearest Service Depot Removing the plug If your appliance has a non rewireable moulded plug and you should wish to re route the mains cable through partitions units etc please ensure that either the plug is replaced by a fused 13 ampere re wearable plug bearing the BSI mark of approval or the mains cable is wired directly into a 13 amp cable outlet controlled by a switch in compliance with BS 5733 which is accessible without moving the appliance Disposing of the plug Ensure that before disposing of the plug itself you make the pins unusable so that it cannot be accidentally inserted into a socket Instructions for connecting cable to an alternative plug Important the wires in the mains lead are coloured in accordance with the following code Green amp Yellow Earth Blue Neutral Brown Live As the colours of the wires in the lead may not correspond with the coloured markings identifyng the terminals in your plug proceed as follows Connect Green amp Yellow wire to terminal marked E or or coloured Green or Green amp Yellow Con
24. to the wash cycles especially where children are at home ECO indicator light the Eco icon lights up when the electricity saving reaches at least 10 this can be achieved by adjusting the wash cycle settings Running a wash cycle NOTE the first time you use the washing machine add etergent and run an empty 90 C cotton wash cycle without the pre wash phase 1 SWITCH ON THE MACHINE Press the button All the indicator lights will illuminate for 1 second after which the light corresponding to the button will remain lit constantly while the START PAUSE indicator light will flash slowly 2 LOAD THE LAUNDRY Open the porthole door Load the laundry making sure that the maximum load quantity indicated in the table of programmes below is not exceeded 3 MEASURE OUT THE DETERGENT Pull out the drawer and pour the detergent into the relevant compartments as described in Description of the machine 4 CLOSE THE PORTHOLE DOOR 5 CHOOSE THE PROGRAMME Turn the PROGRAMME KNOB left or right to select the required programme to which a set temperature spin speed and wash intensity are linked these values may all be modified 6 PERSONALISE THE WASH CYCLE Use the relevant buttons on the control panel Modify the temperature and or the spin speed The machine automatically selects the temperature and the maximum spin speed for the programme set and these values may not be increased By pressing the
25. ully it contains important information regarding the safe installation use and maintenance of the appliance You will find the guarantee and other details relating to the installation process in the bag containing this booklet Unpacking and levelling Unpacking 1 Once the washing machine has been removed from the packaging check that it has not been damaged during transportation If it has been damaged contact the retailer and do not proceed any further with the installation process 2 Remove the four protective screws and the rubber bush with the respective spacer situated on the rear of the appliance NB The plastic spacers may fall down inside the machine once the bolt has been removed and will not interfere with the operation of the machine 3 Close the holes using the plastic covers provided in the bag 4 Keep all the pieces if the washing machine is transported in future the screws and spacers will have to be replaced in order to avoid damaging the inside of the machine Packaging materials should not be used as toys by children Levelling 1 Position the washing machine on a level and sturdy floor without resting it against walls or cabinets 2 If the floor is uneven the feet of the appliance may be adjusted until it reaches a perfectly horizontal position the angle of inclination must not exceed 2 degrees ee If the appliance is levelled correctly it will be more stable an
26. ycle while the laundry is soaking and the Easy Iron indicator light will flash To drain the water so that the laundry can be removed press the START PAUSE button or the Easy Iron button This option is not compatible with the Wool Durable Spin Delicate Spin and Draining programmes gi Extra Rinse This programme increases the efficiency of the rinse phase and ensures that a greater amount of detergent is removed It is particularly recommended for skin types that are sensitive to detergents We recommend this programme is used when the washing machine is full or when a large amount of detergent has been used This option is not compatible with the Fast Wash Durable Spin Delicate Spin and Draining programmes 4 Mini load This function should be used when the amount of laundry is half or less than half of the maximum recommended load see Table of Programmes This option is not compatible with the Durable Spin Delicate Spin and Draining programmes Detergents and laundry Detergent The type and quantity of detergent used depends on the type of fabric cotton wool silk its colour the temperature of the wash the level of soiling and the hardness of the water in the area Measuring out the detergent carefully will avoid accidental spills and help to protect the environment although they may be biodegradable detergents conta
Download Pdf Manuals
Related Search