HomeTech PMS03 User's Manual
Contents
1. for Motion Detection is A1 ON The default for Motion Detection is detect at all times 24 HOUR The default for Time Out that A1 OFF is sent is 1 minute The default House Unit Codes for Dusk Dawn is A2 ON at Dusk A2 OFF at Dawn Note As with all RF transmitter devices electrical fields metal doors or door window frames and appliances can cause interference that can decrease the strength of the transmitted signal Re locating the PATO1 RF Base Transceiver may increase your ability to receive the necessary X10 Signals from the PMSO3 PRO PMS03_03_ 03 07 Tampa FL 33542 Technical Support 800 832 40032. you wish to use before starting the programming procedure because the PMSO3 will only wait a few seconds after it has finished reporting its current setting for you to begin entering the new setting 5 Press the UNIT OFF button the number of times equal to the blink value in the chart above Hold the button down on the last press i e for a setting of 64 minutes press the UNIT OFF button 7 times and hold on the last press 6 A few seconds later the red LED will blink the new setting 7 If the programming fails the red LED will display a sustained blink slightly longer than the report blinks This can occur if you wait too long to start your programming you press the button more than 2 times or you press the HOUSE ON button If the programming procedure fails you must start the procedure over Sensor Detection vs Direction of Motion For best detection results mount the PMSO3 so the person entering the area will cut across the PMSO3 s field of view Do not mount the PMS 03 near hot or cold sources i e heat vents air conditioners direct or reflected sunlight as this may cause false triggering of the PMSO3 Sensor s fields of view are 90 Degrees Horizontally 30 Degrees Vertically and detection range is approximately 20Ft DEFAULTS After replacing batteries please wait 30 seconds before the PMSO3 will see any motion After transmission you need to wait 10 seconds before the PMSO3 will see motion again The default House amp Unit Codes
3. Outdoor Motion Sensor Detects Moti n LED Motion Indicator Code Indicator Manual Off delay and Dusk Dawn E a ter motion Green LED Behind Lens Wireless RF Signal to ae RF Transceiver X10 Code On Off Plugs Into Buttons in Battery Outlet Compartment X10 ACTIVEHOME PATO1 RF Base Sends _ Transceiver sie remote Modi Commands RRR House On Un it Off Description The Outdoor Motion Sensor PMSO03 is a battery operated RF Transmitter capable of sensing Motion and Dusk Dawn events It transmits an X10 Command to an X10 PRO RF Base Transceiver PAT01 which then passes the X10 Command onto the AC wiring of the structure This can be used to control X10 PRO Receiver Modules i e Light and Appliance Modules ON OFF The X10 Command can also be used as a trigger to initiate Macros in the CM11A ActiveHome Two Way Computer Interface Module This would allow for complex routines to be executed as soon as the PMSO3 detects motion The PMSO3 can be used indoors as well Specific Requirements 2 AAA Batteries PATO1 RF Base Transceiver Module Optional Supplementary Devices amp Modules PHH0O2 Chime PLW01 Wall Switch PLM01 Lamp Module X10 Protocol House Code Dial Letters A P Default A Unit Number Dial Numbers 1 16 Default 1 Each X10 Receiver Module is set to a unique Unit Number or to an identical Unit Number as desired Each X10 Controller operating a specific set of Receiver Mod
4. The number of blinks reported by the PMSO3 represent the following Blinks Dawn Dusk Motion Detection 1 Disabled Day amp Night 2 Disabled Night Only 3 Enabled Day amp Night 4 Enabled Night Only 6 If you do not wish to change the current setting take no further action at this point A few seconds later the PMSO3 will timeout The PMSO3 will indicate this to you by displaying a sustained blink slightly longer than the report blinks 7 To change the current setting first select the Dawn Dusk and Motion Detection settings you wish to use from the chart above and remember the blink value listed to the left of them i e for dawn dusk detection enabled and detect motion only at night there are 4 blinks Determine the setting you wish to use before starting the programming procedure because the PMSO3 will only wait a few seconds after it has finished reporting its current setting for you to begin entering the new setting 8 Press the HOUSE ON button the number of times equal to the blink value in the chart above Hold the button down on the last press i e for a setting of dawn dusk detection enabled and detect motion only at night press the HOUSE ON button 4 times and hold on the last press 9 A few seconds later the red LED will blink the new setting 10 If the programming fails the red LED will display a sustained blink slightly longer than the report blinks This can occur if you wait too long to start your programming you pres
5. et above the ground and let it settle for at least 1 minute default with no motion before activation PRO PMS03_03_ 03 07 Tampa FL 33542 Technical Support 800 832 4003 Outdoor Motion Detector Changing the House and Unit Codes 1 Press and hold the House Code button the Red LED flashes first goes off and then blinks the current setting 2 Release and press the desired number of times for the House Code that you want once for A twice for B etc 3 Hold the House Code button on the last press after 3 seconds the Red LED will blink the amount of times to confirm your settings Note For Unit Code changes perform the same as above but using the Unit Code button Motion Detection only after Dusk or 24 hours This section configures the PMSO3 to send the ON Command at dusk no light and the OFF Command at dawn any light for the Unit Code one number higher than the current Unit Code setting i e PMS03 set to A1 will control A2 when dawn dusk is detected When battery power is initially applied to the PMSO3 this feature is disabled This section also configures the PMSO3 to detect motion at all times or only at night The default setting is to detect motion at all times 1 Press the UNIT OFF button once 2 The red LED flashes 3 Press and hold the HOUSE ON button 4 The green LED located behind the sensor window turns on 5 A few seconds later the PMSO3 reports its current setting Release the button
6. s the button more than 2 times or you press the UNIT OFF button If the programming procedure fails you must start the procedure over Delay after Motion before an OFF command is sent When no motion is detected the default amount of time that will pass before the OFF Command is transmitted is Analog i e the setting on the Top Dial under the rubber plug on the top of the PMSO3 The dial adjusts the delay range from 1 minute to 60 minutes The following procedure allows you to alter this setting 1 Press the House button once the Red LED flashes 2 Press and hold the Unit button the Green LED turns ON 3 seconds later the Red LED will report the setting as follows 1 blink for Analog Dial 1 60 Mins 6 blinks for 32 minutes 2 blinks for 2 minutes 7 blinks for 64 minutes 3 blinks for 4 minutes 8 blinks for 128 minutes 4 blinks for 8 minutes 9 blinks for 256 minutes 5 blinks for 16 minutes Note When the setting is 2 blinks or higher the dial on top of the PMSO3 is disabled 3 If you do not wish to change the current setting take no further action at this point A few seconds later the PMSO3 will timeout The PMSO3 will indicate this to you by displaying a sustained blink slightly longer than the report blinks 4 To change the current setting first select the delay time you wish to use from the chart above and remember the blink value listed to the left of it i e for 64 minutes there are 7 blinks Determine the time
7. ules must be set to the same House Code as the Receivers they are controlling Electrical Protocol Nearly all residential homes are wired SPLIT PHASE Each 120V Phase is NOT directly connected with the other 120V phase If after installation an X10 Receiver does not respond to a remote Controller then check to ensure that the breaker serving the X10 Receiver is on the same phase as the Controller If not the breaker can be changed to the opposite phase An alternative solution is recommended to install a Phase Coupler for improving remote communications throughout the home See www x10pro com then select Technical Support and PLC Troubleshooting Installation Setting up the PMS03 1 Remove the battery cover on the front of the PMSO3 and install two AAA alkaline batteries Initially the PMSO3 defaults to House Code A and Unit Code 1 and defaults to See Motion all the time 24hrs 2 Plug in an X10 PRO RF Base Transceiver PAT01 sold separately set the House Code to A 3 Install or plug in an X10 PRO Receiver Module for Light Appliance control and set the Receiver Module to House Code A Unit Code 1 Testing the PMS03 1 Press the House button once the PMSO3 will transmit an RF X10 ON Command and the Red LED will flash 2 Press the Unit button once the PMSO3 will transmit an RF X10 OFF Command and the Red LED will flash The default setting is A1 3 Place the Sensor on a shelf or mount it on a wall at least 6 fe
Download Pdf Manuals
Related Search