Harbor Freight Tools Gear Driven Ring Roller Product manual
Contents
1. PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE DO NOT OPERATE THE TOOL SKU 36790 For technical questions please call 1 800 444 3353 Page 5 Maintenance CLEANING Regularly clean the work surface using a non toxic solvent Zerk Fittings 1 Figure 3 LUBRICATION Your three lubrication points are the Drive Shaft 9 Drive Shaft II 17 and the Adjustable Shaft 18 Grease using the Zerk Fittings 1 see Figure 3 above STORAGE Store in a dry area out of the reach of children Unpacking When unpacking your Metal Planetary Ring Roller check to make sure the following parts are included If any parts are missing or broken please call HARBOR FREIGHT TOOLS at 1 800 444 3353 Parts List Part Description Q ty 3 HexBoltM10x60 4 DriveWheel 5 5 Taper Pin 8 x 28 Copper Bushing 21 Hex Key Screw M10 x 60 Shaft w hole 6 7 8 Bushing 9 Drive Shafti 5 7 Right Frame Mounting Plate 3 4 7 2 2 28 _ Locking Screw M6 x 6 Hex Key Screw M6 x 45 29 Note So2. determine if your judgment reflexes might be impaired Do not wear loose clothing or jewelry as they can be caught in moving parts Protective gloves and non skid footwear are recommended Wear restrictive hair covering to contain long hair Use eye and ear protection Always wear ANSI approved impact safety goggles Maintain proper footing and balance at all times Use the right tool for the job Do not attempt to force a small tool or attachment to do the work of a larger industrial tool There are certain applications for which this tool was designed Do not modify this tool and do not use this tool for a purpose for which it was not intended For your own safety maintenance should be performed regularly by a qualified technician WARNING The brass components of this product contain lead a chemical known to the State of California to cause birth defects or other reproductive harm California Health amp Safety code 25249 5 et seq REV 12 06 SKU 36790 For technical questions please call 1 800 444 3353 Page 2 Work Area TO AVOID RISK OF PERSONAL INJURY EQUIPMENT DAMAGE FIRE AND SHOCK MAKE SURE YOUR WORK AREA IS Free of damp wet or rainy conditions Free of children never let them handle tools or machinery Well lit Clean and uncluttered Before Operating Make sure all clamps locks and bolts are tight and that the Ring Roller is securely fastened to the appropriate mounting surface Assembly Your Ri
3. 3 Page 3 Mounting tep 1 tep 2 tep 3 tep 4 tep 5 Upper Drive Wheel 4 Lower Drive Wheel 4 SKU 36790 Taper Pin 20 into the hole as seen in Figure 1 If necessary lightly tap the Taper Pin 20 into place Set the Roller on your appropriate mounting surface as desired The Metal Planetary Ring Roller must be securely mounted to an appropriate work surface prior to use Make certain that you can operate the Handle 15 comfortably Mark the appropriate mounting surface through the two holes located at the far ends of the Base 25 Remove the Metal Planetary Ring Roller from the appropriate mounting surface Drill holes through the mounting surface at the marked locations Mount the unit using two bolts lock washers washers and nuts in that order sold separately Handle 15 Knob 29 Adjustable Wheel 16 Left Frame 5 For technical questions please call 1 800 444 3353 Page 4 Operation When operating your Metal Planetary Ring Roller it may be helpful to refer to each of the operational Figures as well as to the Parts List and Assembly Diagram located on the last pages of this manual Never force the tool or attachment to do the work of a larger industrial tool It is designed to do the job better and more safely at the rate for which it was intended tep 1 Determine the size ring you wish to obtain Do not use flat stock larger than 3 16 x 1 Do not use
4. METAL PLANETARY RING ROLLER Wexel 11 36790 ASSEMBLY AND OPERATION INSTRUCTIONS 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http Awww harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2000 2006 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 THANK YOU for choosing a HARBOR FREIGHT TOOLS product For future reference please complete the owner s record below Model Serial No Purchase Date SAVE THE RECEIPT WARRANTY AND THESE INSTRUCTIONS It is important that you read the entire manual to become familiar with the unit BEFORE you begin assembly Specifications IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that COMMON SENSE AND CAUTION ARE FACTORS WHICH CANNOT BE BUILT INTO THIS PRODUCT BUT MUST BE SUPPLIED BY THE OPERATOR The Operator PLEASE REMEMBER Do not operate the product if under the influence of alcohol or drugs Read warning labels on prescriptions to
5. Round stock larger than 1 4 tep 2 Move the Adjustable Wheel 16 up or down as desired by turning the Knob 29 see Figure 2 tep 3 To obtain small size rings approximately 1 the Adjustable Wheel 16 must be in its uppermost position To obtain 2 rings the Adjustable Wheel 16 must be in the middle position op tep 5 To obtain larger rings the Adjustable Wheel 16 must be in its lowest position t is recommended that you practice on scrap stock to find the correct wheel adjustment to make the desired size ring Step 6 Insert the stock between the Upper Drive Wheel 4 and between both the Adjustable Wheel 16 and lower Drive Wheel 4 see Figure 2 Step 7 Turn the Knob 29 clockwise to clamp the stock between the Wheels Warning After stock has been clamped between the Wheels keep hands and fingers clear of the Wheels while the handle is being rotated Step 8 Rotate the Handle 15 counterclockwise to process the ring Step 9 To remove the completed rings turn the Knob 29 counterclockwise to loosen the clamping action PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEM BLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY
6. me parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 36790 For technical questions please call 1 800 444 3353 Page 6 Assembly Diagram h 7 OY PRIS aN o WA a f A N e SKU 36790 For technical questions please call 1 800 444 3353 Page 7
7. ng Roller will require minor assembly prior to operation It is important that you read the entire manual to become familiar with the unit BEFORE you assemble and use the Ring Roller Before assembling your Ring Roller be sure that you have all parts described in the Parts List When assembling your Ring Roller it will be helpful to refer to each of the operational Figures as well as to the Parts List and Assembly Diagram on the last pages of this manual Assemble attachments based on the intended use of the Ring Roller only Mounting Surface The mounting surface must be flat level and capable of supporting the weight of the Roller combined with the materials to be rolled Mount the Ring Roller on a solid mounting surface that is capable of supporting the weight of the Ring Roller and the leverage force of the Handle movement Step 1 Slide the Connector 19 onto the Drive Shaft Il 17 see Figure 1 Once the Connector 19 is slid in Figure 1 place on the Drive Shaft Il 17 make certain that the holes in the Connector 19 line up with the holes in the Drive Shaft Il 17 Step 2 Slide the Handle 15 into the hole Handle 15 in the Connector 19 and Drive Shaft Il 17 6G ee _ Connector 19 Step 3 Secure the Connector 19 to the Insert Taper Pin 20 here Drive Shaft Il 17 using the Taper Pin 20 Insert the Base 25 Mounting Hole SKU 36790 For technical questions please call 1 800 444 335
Download Pdf Manuals
Related Search