Harbor Freight Tools 13 in. Electric String Trimmer Product manual
Contents
1. Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference POR TCASID ELECTRIC 3 STRING TRIMMER ITEM 62338 Visit our website at http www harborfreight com REV 14f Email our technical support at productsupport harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 888 866 5797 as soon as possible Copyright 2014 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Table of Contents 2 12 52. 60Hz 4A No Load Speed 9 000 RPM Replacement Line Type 0 065 Nylon The spool will continue to rotate for a few seconds after use Allow it to stop completely and unplug it before putting the appliance down making any adjustments or servicing the appliance Do not use in rain snow sprinklers or wet grass Do not rinse off the Trimmer Use only during daylight hours Carefully inspect the wire spool and guard before plugging in the Trimmer Do not use Trimmer if any part is cracked or damaged Cover the Trimming Blade after every use Do not use appliance for other than intended use Maintain labels and nameplates on the appliance These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator A SAVE THESE INSTRUCTIONS POR TCANID Item 62338 For technical questions please call 1 888 866 5797 Page 5 SAFETY Set Up Instructions Read the ENTIRE IMPORTANT SAFETY INSTRUCTIONS section at the beginning of this manual including all text under subheadings therein before set up or use of this product AWARNING TO PREVENT SERIOUS INJURY FRO
3. S pR 31_jlabel Ct Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Page 14 For technical questions please call 1 888 866 5797 Description 32 RubberPad Reel 3 1 A NutM6 2 Nylon Line 0 065 4 3 Rotor 4 4 1 2 8X0 8Terminl 5 60822 6 Motor Bracket __ __ 7 Bolt M4x82 i O 8 Spring Washer4 9 Washer4 i O 44 11 Stap 2 Item 62338 Assembly Diagram 4 he y 11 MAINTENANCE Item 62338 For technical questions please call 1 888 866 5797 Page 15 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or
4. be sure to use one heavy enough to carry the current your product will draw An undersized extension cord will cause a drop in line voltage resulting in loss of power and overheating Personal Safety 1 Dress Properly Do not wear loose clothing or jewelry They can be caught in moving parts Use of rubber gloves and substantial footwear is recommended when working outdoors Wear protective hair covering to contain long hair Wear ANSl approved safety goggles and heavy duty work gloves Use face or dust mask if operation is dusty 3 Avoid Unintentional Starting Do not carry plugged in appliance with finger on switch Be sure switch is off when plugging in 4 Do not Overreach Keep proper footing and balance at all times 5 Stay Alert Watch what you are doing Use common sense Do not operate appliance when you are tired Item 62338 Extension Cord Size The following table shows the correct cord size to use depending on cord length and nameplate ampere rating If in doubt use the next heavier gauge The smaller the gauge number the heavier the cord TABLE MINIMUM WIRE GAUGE FOR EXTENSION CORDS 120 VOLT Ampere Rating EXTENSION CORD LENGTH at full load 25 SAFETY Connecting Cords To reduce the risk of the cords pulling apart during operation a Make a loop in the extension cord and press that cord loop through the hole in the handle b Hook that cord loop around the co
5. Parts List and Diagram 14 6 16 9 POR TCANID WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER Indicates a hazardous situation which if not avoided will result in death or serious injury AWARNING Indicates a hazardous situation which if not avoided could result in death or serious injury Indicates a hazardous situation which if not avoided ACAUTION could result in minor or moderate injury NOTICE CAUTION IMPORTANT SAFETY INSTRUCTIONS AWARNING When using electric gardening appliances basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury including the following READ ALL INSTRUCTIONS Power Cord Safety Addresses practices not related to personal injury WARNING To reduce the risk of electric 1 Ground Fault Circuit Interrupter GFCI protection shock use only with an extension cord should be provided on the circuit s or outlet s to intended for outdoor use such as an be used for the gardening appliance Receptacles extension cord of cord type are available having built in GFCI protection SW A SOW A STW A STOW A SJW A and may be used for this measure of sa
6. consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state POR TCAD 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 1 888 866 5797
7. please call 1 888 866 5797 Item 62338 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO MAINTENANCE Item 62338 For technical questions please call 1 888 866 5797 Page 13 m gt O m Parts List and Diagram Parts List _ _ _ N oy 7 7 N a 1S Se Power Cord Cord Protector _ o O cket O a y 9 o D O Q L eft Housing eft Housing Cover 3 2 o gt 0 Q 2 O Part 32 Nut M6 AK 4 2 AJA AIA ES AIR N 2 Pln A P INENENININ AVA AJR 9 Z
8. M ACCIDENTAL OPERATION Make sure that the Power Switch Trigger is in the off position and unplug the appliance from its electrical outlet before performing any procedure in this section Note For additional information regarding the parts listed in the following pages refer to the Assembly Diagram near the end of this manual Assembly Install Guard 1 CAUTION TO PREVENT ACCIDENTAL CUTS Cover the Trimming Blade 39 with the Blade Cover 40 before installing the Guard 2 Align Guard 42 over Housing as shown in Figure A Screw 25 WARNING TO PREVENT SERIOUS INJURY FROM FLYING DEBRIS AND PIECES OF TRIMMING LINE Install the guard only in the orientation shown 3 Attach Guard to Housing using 4 Screws 25 Install Auxiliary Handle 1 Position Auxiliary Handle over Handle Bracket 14 2 Install Locking Knob 15 and tighten it in place to secure the Handle 3 Loosen the Locking Knob and move the Auxiliary Handle to the desired position WARNING Tighten the Locking Knob after adjustment Locking Knob 15 Auxiliary Handle Handle Bracket 14 Figure B Auxiliary Handle Installation Page 6 For technical questions please call 1 888 866 5797 Item 62338 Install Edge Guide 1 Snap Edge Guide 21 into holes on both sides of Housing as shown in Figure 2 Use the Edge Guide to limit striking objects with the Line while trimming nearby
9. _ Edge Guide 21 3 Flip the Edge Guide up out of the way when not in use Figure C Install Edge Guide SETUP Item 62338 For technical questions please call 1 888 866 5797 Page 7 Functions Trigger Auxiliary Handle Cord Hook Length Sleeve Head Angle Button Guard Edge Guide Line Reel Available Accessories Attachments AWARNING Use of any accessory or attachment other than those listed below may increase the risk of serious injury Only replace the line on this appliance with the line material and diameter of line listed on the Specifications table Other materials such as wire rope or blades can damage the appliance and be forcefully and dangerously ejected from the appliance upon breaking Accessories and attachments are not available for this product Page 8 For technical questions please call 1 888 866 5797 Item 62338 Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product AWARNING TO PREVENT SERIOUS INJURY Before operating the gardening appliance put on ANSI approved safety goggles close toed work boots long pants and other safety gear Safety goggles and other safety gear are sold separately TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION Make sure that the Power Switch Trigger is in the off position and unplug the applianc
10. age it and cause it to break 7 To prevent accidents turn off the appliance and unplug it after use Clean then cover the Trimming Blade with the Blade Cover and store the appliance indoors out of children s reach Page 11 Z Lu ou 2 gt m Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician AWARNING TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION Make sure that the Power Switch Trigger is in the off position and unplug the appliance from its electrical outlet before performing any procedure in this section TO PREVENT SERIOUS INJURY FROM APPLIANCE FAILURE Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further use Cleaning Maintenance and Lubrication 1 BEFORE EACH USE inspect the general 2 AFTER USE clean external surfaces of condition of the appliance Check for the appliance with clean moist cloth loose hardware 3 To feed replace trimming Line e misalignment or binding of moving parts see instructions on page 10 damaged cerdiclecttical witihg 4 AAWARNING If the supply cord of this cracked or broken parts and appliance is damaged it must be replaced any other condition that may only by a qualified service technician affect its safe operation 12 For technical questions
11. e from its electrical outlet before setting up the appliance Using Cord Hook 1 extension cord sold separately will be 3 Secure the extension cord required Ensure that the extension cord is an using the cord hook outdoor type extension cord and that it is the as explained below correct design to accept this appliance s plug a Make a loop in the 2 WARNING extension cord and TO PREVENT ELECTRIC SHOCK AND press that cord loop through SERIOUS PERSONAL INJURY the hole inthe handle The extension cord must remain b Hook that cord loop secured to the appliance s plug around the cord hook c Make sure the Trigger is released then plug the cord ends together Z ad Lu ou Item 62338 For technical questions please call 1 888 866 5797 Page 9 5 2 Replacing Nylon Line 1 Press in buttons on side of Reel 33 and remove Reel Cover 38 and Spool 36 Reel Figure D Reel Assembly 2 Remove all old Line from Spool 3 Cut two equal lengths of 0 065 Nylon Line 4 Insert one Line into hole in top groove of Spool Figure E Insert Line Feeding Nylon Line NOTICE To prevent damage DO NOT BUMP REEL This string trimmer feeds Line automatically when stopping 1 Make sure area is safe to operate appliance in then operate it at full speed 2 AN 2 Release Trigger and allow Line to stop fully Adjusting Working Height 1 Loosen the Length Sl
12. ects that may be thrown during operation Keep extension cord clear of work area Edger Operation 1 If head is in horizontal position pull back on Angle Sleeve rotate head 180 and release Angle Sleeve CAUTION Make sure Angle Sleeve locks in the new position 2 To adjust head angle press the Head Angle Button 27 adjust as desired and release Button CAUTION Make sure head angle locks in the new position 3 Clear the work area of all fragile objects and all objects that may be thrown during operation Keep extension cord clear of work area 4 Remove the Blade Cover and keep it available Item 62338 For technical questions please call 1 888 866 5797 4 Remove the Blade Cover and keep it available 5 Make sure Trigger is released then connect the Power Cord to the extension cord see Using Cord Hook on page 9 6 Squeeze the Trigger and slowly move the spinning Line across the work area CAUTION DO NOT STRIKE THE HEAD doing so may damage it and cause it to break 7 To prevent accidents turn off the appliance and unplug it after use Clean then cover the Trimming Blade with the Blade Cover and store the appliance indoors out of children s reach 5 Make sure Trigger is released then connect the Power Cord to the extension cord see Using Cord Hook on page 9 6 Squeeze the Trigger and slowly move the spinning Line across the work area CAUTION DO NOT STRIKE THE HEAD doing so may dam
13. eeve 2 Adjust the Tube to the desired Length 3 Tighten the Length Sleeve Page 10 For technical questions Cover 38 5 Wind onto top groove using slight tension and following arrow direction Press Line into clip on top of Spool Figure F Wind Line 6 Repeat to wind other Line onto bottom groove Press Line into clip on other side of Spool 7 Insert Spool partway into Reel insert Line ends through round holes in side of Reel unclip Lines and pull Line ends snug 8 Reassemble Reel Cover onto Reel and make sure that both buttons pop back into place 3 Line will feed slightly Repeat as desired Note Line will feed only if Spool is wound correctly and can unwrap freely 4 To manually feed Line unplug the Power Cord press the Feed Button 34 at the base of the Reel and pull out the Line slightly Keep pushing the Button and pulling the Line out until the Line reaches the desired length Angle Sleeve Length Sleeve Figure G Tube Adjusting Sleeves please call 1 888 866 5797 Item 62338 Trimmer Operation 1 If head is in vertical position pull back on Angle Sleeve rotate head 180 and release Angle Sleeve CAUTION Make sure Angle Sleeve locks in the new position 2 To adjust head angle press the Head Angle Button 27 adjust as desired and release Button CAUTION Make sure head angle locks in the new position 3 Clear the work area of all fragile objects and all obj
14. ended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and any other condition that may affect its operation A guard or other part that is damaged should be properly repaired or replaced by a qualified technician unless indicated elsewhere in this manual Disconnect Appliance Disconnect the appliance from the power supply when not in use before servicing when changing accessories such as blades and the like Keep guards in place and in working order Only replace the line on this appliance with the line material and diameter of line listed on the Specifications table Other materials such as wire rope or blades can damage the appliance and be forcefully and dangerously ejected from the appliance upon breaking Do not smoke during use Nicotine reduces the blood supply to the hands and fingers increasing the risk of vibration related injury Wear suitable gloves to reduce the vibration effects on the user Use appliances with the lowest vibration when there is a choice between different processes Include vibration free periods each day of work Grip appliance as lightly as possible while still keeping safe control of it Let the appliance do the work To reduce vibration maintain the appliance as explained in this manual If any abnormal vibration occurs stop use immediately Item 62338 General Safety 1 Specifications Electrical Rating 120VAC
15. fety SJOW A SJTW A or SJUTOW A 2 not Abuse Cord Do not carry appliance by cord or yank it to disconnect from receptacle Keep cord from heat oil and sharp edges Page 2 For technical questions please call 1 888 866 5797 Item 62338 3 reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other and will require the use of a polarized extension cord The appliance plug will fit into a polarized extension cord only one way If the plug does not fit fully into the extension cord reverse the plug If the plug still does not fit obtain a correct polarized extension cord A polarized extension cord will require the use of a polarized wall outlet This plug will fit into the polarized wall outlet only one way If the plug does not fit fully into the wall outlet reverse the plug If the plug still does not fit contact a qualified electrician to install the proper wall outlet Do not change the equipment plug extension cord receptacle or extension cord plug in any way This design is referred to as double insulated indicated by 4 WARNING The cord of this product contains lead a chemical known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling California Health amp Safety Code 25249 5 et seq 5 Extension Cord Make sure your extension cord is in good condition When using an extension cord
16. n Appliance With Care Keep cutting edge sharp and clean for best performance and to reduce the risk of injury Follow instructions for lubricating and changing accessories Inspect appliance cord periodically and if damaged have it repaired by an authorized service facility Inspect extension cords periodically and replace if damaged Keep handles dry clean and free from oil and grease Vibration Hazard This appliance vibrates during use Repeated or long term exposure to vibration may cause temporary or permanent physical injury particularly to the hands arms and shoulders To reduce the risk of vibration related injury 1 Page 4 Anyone using vibrating appliances regularly or for an extended period should first be examined by a doctor and then have regular medical check ups to ensure medical problems are not being caused or worsened from use Pregnant women or people who have impaired blood circulation to the hand past hand injuries nervous system disorders diabetes or Raynaud s Disease should not use this appliance If you feel any symptoms related to vibration such as tingling numbness and white or blue fingers seek medical advice as soon as possible 9 11 12 For technical questions please call 1 888 866 5797 Check Damaged Parts Before further use of the appliance a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its int
17. rd hook c Make sure the Trigger is released then plug the cord ends together Wear thick jeans and steel toed work boots to help prevent injury caused by flying debris People with pacemakers should consult their physician s before use Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure In addition people with pacemakers should e Avoid operating alone Don t use with power switch locked on e Properly maintain and inspect to avoid electrical shock Any power cord must be properly grounded Ground Fault Circuit Interrupter should also be implemented it prevents sustained electrical shock For technical questions please call 1 888 866 5797 Page 3 9 gt m lt Gardening Appliance Use and Care 1 Avoid Dangerous Environment Do not use appliances in damp or wet locations Do not Use In Rain Keep Children Away All visitors should be kept at a distance from work area When servicing use only identical replacement parts Use Right Appliance Do not use appliance for any job except that for which it is intended Do not Force Appliance It will do the job better and with less likelihood of injury at the rate for which it was designed Store Idle Appliances Indoors When not in use appliances should be stored indoors in dry and high or locked up place out of reach of children Maintai
Download Pdf Manuals
Related Search