Hannspree 19 Inch Screen TFT LCD Monitor User's Manual
Contents
1. REGULATORY INFORMATION Before operating the monitor please read this manual thoroughly This manual should be retained for future reference FCC Class Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures A Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help The device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device2. Other Setting 720 400 640 400 HANNspree 17 OSD Diagram OSD Description Recall the factory settings Select the Factory Preset option to reset 9 027 03 to the monitor s default setting This will Factory Preset erase the current settings Press enter and select On or Off Other Setting Off Input Setting Main Menu Select the Input Setting option to change H0 E269 BO ES between the analog D Sub or Digital DVI source Press enter and select Analog or Digital Analog Digital H 80 0KHz V 75 0Hz 1280x1024 PLUG AND PLAY Plug amp Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD It allows the monitor to inform the computer or host system of its identity and depending on the level of DDC used communicate additional information about its display capabilities The DDC2B is a bidirectional data channel based on the C protocol The host can request EDID information over the DDC2B channel If your computer video card and operating system support DDC2B your monitor should automatically be set to it s optimal configuration Some computer systems may not have the capability to properly detect this information In addition some computer systems will require manually configuring the video options In most cases software and or driver updates will correct this issue Please contact your computer or video card ma
3. WY 39J0SNNVH HANNSpree 19 inch Screen TFT LCD Monitor n HANNSPREE INC www hannspree com Table of Contents REGULATORY INFORMATION 2 4 SAFEFY NORGE passerer 5 PRECAUTIONS vasene 5 SPECIAL NOTES ON LCD 5 6 FREE EP 7 BEFORE YOU OPERATE THE 2 8 PEA DURES etsende 8 CHECKING THE CONTENTS OF THE PACKAGE 8 91 12 9 CONTROLS AND 5 2222 2 10 ADJUSTING THE VIEWING 2 1 11 OPERATING 8 1 222 12 GENERAL INSTRUGTIONS need 12 FRONT PANEL GCONTROL dets 13 HOW TO ADJUST A SETTING 14 dE ICE IDEE Sgen 18 TECHNICAL SUPPORT FAQ unne 19 Q amp A FOR GENERAL DEFECTS 1 19 ERROR MESSAGE amp POSSIBLE SOLUTION 20 APPENDIX 21 wpsl c 21 CONNECTOR PIN ASSIGNMENT 1 22 HANNspree
4. surge protection power strip or device 5 Turn on your monitor and computer e e de le le ie de ie ie ic id lc ie id ic id ic le id ic ie id Le id Lo Le 1d Le 1e y Le d PG m Figure 2 Connecting Cables D Sub Input DVI D Input Audio Input Power AC Input 10 Hannspree ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor then adjust the monitor s angle to your own preference e Hold the stand so you do not topple the monitor when you change the monitor s angle e You are able to adjust the monitor s angle at 20 alternative from 5 to 15 0 to 20 e For more information please refer to the Quick Start Guide of your Monitor model A Figure 3 monitor s angle NOTES e Avoid touching the LCD screen when changing the viewing angle as it may cause damage e Be careful not to place fingers or hands near the hinges when tilting the monitor otherwise pinching can result HANNspree 17 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off The other control buttons are located at front panel of the monitor See Figure 4 By changing these settings the picture can be adjusted to your personal preferenc
5. tub swimming pool or in a wet basement Do not place the monitor on an unstable cart stand or table If the monitor falls it can injure a person and cause serious damage to the appliance Use only a cart or stand recommended by the manufacturer or sold with the monitor If you mount the monitor on a wall or shelf use a mounting kit approved by the manufacturer and follow the kit instructions olots and openings in the back and bottom of the cabinet are provided for ventilation To ensure reliable operation of the monitor and to protect it from overheating be sure these openings are not blocked or covered Do not place the monitor on a bed sofa rug or similar surface Do not place the monitor near or over a radiator or heat register Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided The monitor should be operated only from the type of power source indicated on the label If you are not sure of the type of power supplied to your home consult your dealer or local power company Unplug the unit during a lightening storm or when it will not be used for long period of time This will protect the monitor from damage due to power surges Do not overload power strips and extension cords Overloading can result in fire and or electric shock Never push any object into the slot on the monitor cabinet It could short circuit parts causing a fire or electric shock Never spill liquids on the monitor Do not at
6. Guide of your Monitor model Cables and User manual Power Cord User s manual Warranty and Service Manual DVI D Cable Optional Note Images are for illustration only and may vary by model or region Hannspree POWER POWER SOURCE 1 Make sure that the power cord is the correct type required in your area 2 This LCD monitor has an Internal universal power supply that allows operation in either 100 120V AC or 220 240V AC voltage area No user adjustment is required 3 Plug one end of the AC power cord into the LCD monitor s AC input socket and the other into a surge protection power strip or device HANNspree 9 CONTROLS AND CONNECTORS CABLE CONNECTIONS Turn off your computer before performing the procedure below 1 Connect one end of the 15 pin D Sub cable to the back of the monitor and connect the other end to the computer s D Sub port 2 Connect one end of 24 DVI D to the back of the monitor Connect the other end to the computer s DVI D port note This monitor is capable of operating in Dual input mode Only one of either the 15 pin D sub or the 24 pin DVI D connections is needed for normal operation 3 Connect the audio cable between the monitor s audio input and the PC s audio output green port This connection is optional and not required for normal operation of the monitor 4 Plug one end of the AC power cord into the LCD monitor s AC input socket and the other into
7. OSSIBLE SOLUTION CABLE NOT CONNECTED 1 Check whether the signal cable is properly connected If the connector 15 loose tighten the connector screws 2 Check the signal cable s connection pins for damage INPUT NOT SUPPORT Your computer has been set to an unsuitable display mode Set the computer to a display mode from the table below FACTORY PRESET TIMING TABLE twine REQVENGY He FREQUENCY H2 FREQUENCY kHz FREQUENCY Hz 1024x768 1024x768 1152x864 1280x960 1280x1024 64 1280x1024 1440x900 1440x900 The two timing modes are for 19 widescreen support only 20 Hannspree APPENDIX SPECIFICATIONS 0 2835 H x E 2835 V 10 294 x 0 294 V Video R G B Analog Interface Digital Dual Input Model H V TTL Input H Frequency 31KHz 80KHz Audio maximum power output maximum power Audio maximum power output 1 2W Amplifier D Sub 15pin Input Connector DVI D 24pin Dual Input Model Hor 408 24mm Ver 255 15mm Operating Temp 5 to 35 C Storage Temp 20 to 60 C Operating Humidity 10 85 non condensing LMO1 465 193 482 mm 02 485 212 402 mm Dimensions W D H 449 293 416 mm LMO5 449 180 409 mm 485 293 482 mm Weight GW NW Max 8 kg 6 5 kg UL CUL BSMI CCC CE CB PSB FCC VCCI C TICK NEMKO GS TCO 03 Maximum Screen Size Environmental Considerations Regulatory Compliance The above specificati
8. SD Press enter and adjust the level OSD vertical position adjustment Select the OSD V Position option to adjust the vertical position of the OSD Press enter and adjust the level OSD timer setting Select the OSD Time out option to set the OSD time out from 10 to 120 seconds Press enter and adjust the level OSD Transparency setting Select the OSD Transparency option to adjust the transparency of the OSD Press enter and adjust the level OSD Diagram OSD Description OSD color setting Select the OSD Color setting option to adjust the color of the OSD Press enter and adjust the level 1 2 3 4 5 6 OSD Setting Language Select the Language option to change the language of the OSD Press enter and select a language TE Please note the diagram is for reference EM 5 only The OSD Language options may vary Fran ais Espa ol by model and region Italiano Portugu s Nederlands OSD Setting Volume adjustment Select the Volume option to change the volume level Press enter and adjust the level 50 Other Setting Other Settin Sharpness Select the Sharpness option to adjust the 9 es e sharpness of the display Set the value from Sharpness 0 to 6 0O 1 2 3 4 5 6 DOS mode Select the DOS mode option to set the 9 022 003 ER monitor for use with PC Press enter and DOS Mode select 720 x 400 or 640 x 400
9. Setting IG Phase Adjustment Main Menu Oro E H 80 0KHz V 75 0Hz 1280x1024 Color Setting olson a Es Color Setting User B OSD Description Clock adjustment Select the Clock Adjustment option to reduce the vertical flicker of characters on the screen Press enter and adjust the level Phase adjustment Select the Phase Adjustment option to reduce the horizontal flicker of characters on the screen Press enter and adjust the level How to adjust color Select the Color Setting option on the Main Menu and then Press enter Move the cursor to one of the preset options and select it User defined option Move the cursor to the User option and select it 1 To adjust the red enter the R option and adjust the level 2 To adjust the green enter the option and adjust the level To adjust the blue enter the B option and adjust the level HANNspree 15 OSD Diagram Main Menu EDEPP RR H 80 0KHz V 75 0Hz 1280x1024 OSD Setting 19 H Fesition OSD V Position OSD Time out OSD Transparency 0 lt 1 lt 2 lt 3 lt 4 lt 5 lt 6 16 Hannspree OSD Description How to set the OSD Select OSD Setting on the Main Menu and then Press enter OSD horizontal adjustment Select the OSD H Position option to adjust the horizontal position of the O
10. es e he power cord should be connected e Connect the Signal cable from the monitor to the computer e Press the power button to turn on the monitor The LED will turn green Figure 4 External Control Button EXTERNAL CONTROLS AUTO 6 Power Indicator LED 1 2 HANNspree FRONT PANEL CONTROL e Power Button Press this button to switch the monitor on and off Power Indicator LED Green Power On mode Orange Power saving mode MENU ENTER 1 Activate the OSD menu or adjust the function settings and confirmation 2 Exit OSD menu when in volume OSD status e VOL VOL 1 Activates the volume control when the OSD is OFF 2 Navigate through adjustment icons when OSD is ON or adjust function when function is activated Auto Adjust button When OSD menu 15 in off status press this button to activate the Auto Adjustment function The Auto Adjustment function is used to optimized the H Position V Position Clock and Phase NOTES Do not install the monitor in location near heat sources such as radiators or air dusts or in place subject to direct sunlight or excessive dust or mechanical vibration or shock e Save the original carton and packing materials as they will come in handy if you ever have to ship your monitor e o ensure problem free shipping pack your monitor in the same packing materials and carton as it was shipped from the factory e o keep the mon
11. itor looking new periodically clean it with a soft cloth Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution Never use strong solvents such as paint thinners benzene or abrasive cleaning products These and other harsh cleaning agents will damage the cabinet of the monitor HANNspree 13 HOW TO ADJUST SETTING OSD Description OSD Diagram Main Menu 52 0 54 9 09 H 80 0KHz V 75 0Hz 1280x1024 Main Menu 12 2 99 09 m 99 Corr H 80 0KHz V 75 0Hz 1280x1024 Main Menu 0 zz 69 090 80 88 Seng H 80 0KHz V 75 0Hz 1280x1024 Image Setting Image Setting e e Tw s e 14 Hannspree Brightness adjustment Select the Brightness option on the Main Menu Press enter adjust the level Contrast adjustment Select the Contrast option on Main Menu Press enter and adjust the level How to adjust screen position and quality Select Image Setting on the Main Menu and then Press enter Horizontal position adjustment Select the H position option to shift the screen image to the left or right Press enter and adjust the level Vertical position adjustment Select the V position option to shift the screen image up or down Press enter and adjust the level OSD Diagram Image Setting e em n Clock Adjustment Image
12. must accept any interference received including interference that may cause undesired operations CANADA This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulation C This device complies with requirement of EMC directive 89 336 EEC with regard to Electromagnetic Compatibility and 73 23 EEC and 93 68 EEC with regard to Low Voltage directive Socket outlet shall be near the equipment and shall be accessible 2 Hannspree TCO 03 TCO 03 applied model only Congratulations The display you have just purchased carries the TCO 03 0 Displays label This means that your display is designed manufactured and tested according to some of the strictest DISPLAYS quality and environmental requirements in the world This makes for a high performance product designed with the user in focus that also minimizes the impact on our natural environment Some of the features of the TCO 03 Display requirements Ergonomics Good visual ergonomics and image quality order to improve the working environment for the user and to reduce sight and strain problems Important parameters are luminance contrast resolution reflectance colour rendition and image stability Energy e Energy saving mode after certain time beneficial both for the user and the environment e Electrical safety Emissions Electromagnetic fields e Noise emissions Ecology The p
13. ng Hannspree Liquid Crystal Display Monitor LCD Monitor Please carefully read this manual in its entirety before setting up using or operating your Monitor To ensure the safe and correct installation and operations of the Monitor it is important that the safety and operation instructions in this manual are followed This instruction manual is designed to assist you in setting up and using the Monitor The information in this manual has been carefully checked for accuracy however no guarantee is given to the correctness of the contents The information in this manual is subject to change without notice To the extent allowed by applicable law Hannspree Inc Hannspree shall not be liable for direct indirect special exemplary incidental or consequential damages arising from any defect or omission in this manual even if advised of the possibility of such damages in advance HANNspree 7 BEFORE YOU OPERATE THE MONITOR FEATURES e 10 screen TFT Color LCD Monitor e Crisp Clear Display e Recommended Resolutions 19 Wide 16 10 1440 X 900 19 5 4 1280 X 1024 EPA ENERGY STAR e Ergonomic Design e Space Saving Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items LCD Monitor 00000 Screen Base Note The screen and base design may vary on different models For more information please refer to the Quick Start
14. nufacturer for more details THIS MONITOR WILL APPEAR TO BE NON FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY THERE MUST BE A VIDEO INPUT SIGNAL This monitor meets the Green monitor standards as set by the Video Electronics Standards Association VESA and or the United States Environmental Protection Agency EPA and The Swedish Confederation Employees NUTEK This feature is designed to conserve electrical energy by reducing power consumption when there is no video input signal present When there is no video input signal this monitor following a time out period will automatically switch to an OFF mode This reduces the monitor s internal power supply consumption After the video input signal is restored full power is restored and the display is automatically redrawn The appearance is similar to a Screen Saver feature except the display is completely off The display is restored by pressing a key on the keyboard or clicking the mouse 18 Hannspree TECHNICAL SUPPORT FAQ Q amp A FOR GENERAL DEFECTS PROBLEM amp QUESTION POSSIBLE SOLUTION Power LED is not on Check the power cord No Plug amp Play or screen Check if the PC system is Plug amp Play compatible image is stretch or seems Check if the Video Card is Plug amp Play compatible out of proportion Check if the D 15 plug pin of Video Cable is bent or broken Adjust the Clock Phase or Contrast and Brightne
15. on is subject to actual panel specification and is subject to change without prior notice Applied models only Note Maximum Resolution is dependant on the support of your computer system and video card Please see http www hannspree com for more information HANNspree 21 CONNECTOR PIN ASSIGNMENT 15 Pin Color Display Signal Cable PIN NO DESCRIPTION PIN NO DESCRIPTION __ Reg 9 Green 10 Cable Detection Bue 11 Gomd gt Ground 12 DDCG SerialData 13 gt S 15 gt 7 DDC Serial Clock B Ground 4 24 Color Display Signal Cable Dual Input Mode 10 11 12 1 14 15 PINNO DESCRIPTION TMDS Clock Shield 11 TMDS Data 1 3 Shield 12 NoConnection EE CUN 22 i __5_ 6 DDCCok 1 15 8 09 00 2 3 4 5 f 10 11 12 22 Hannspree HANNSPREE CALIFORNIA ING TEL 1 510 360 3080 Toll Free 1 888 808 6789 FAX 1 510 360 3001 Corporate website http www hannspree com us Service website http usservice hannspree net Service Email webservice_us hannspree com Australia Phone 1 300 HANNSPREE 1 300 426677 Corporate website http www hannspree com au Service website http auservice hannspree net New Zealand Phone 0 800 HANNSPREE 0 800 426677 Corporate website http www hannspree com nz Service website htt
16. p nzservice hannspree net Europe GmbH TEL 49 0 2154 953 23 0 FAX 49 0 2154 953 23 123 Corporate website http www hannspree com eu Service website http euservice hannspree net io RIT ES BEAR 2 DI 23 886 2 87518000 886 2 87514755 Corporate website http www hannspree com tw Service website http twservice hannspree net Er CERE A 86 21 3912 6999 86 21 3912 6969 Corporate website http www hannspree com cn Service website http cnservice hannspree net Hannspree Hong Kong Service Center TEL 852 23453822 FAX 852 23453790 Corporate website http www hannspree com hk Service website http hkservice hannspree net Japan 03 6914 5088 7 7 17 5 03 6914 5087 Corporate website http www hannspree com jp Service website http joservice hannspree net
17. roduct must be prepared for recycling and the manufacturer must have certified environmental management system such as EMAS or ISO 14 001 e Restrictions on O chlorinated and brominated flame retardants and polymers O heavy metals such as cadmium mercury and lead The requirements included in this label have been developed by TCO Development in cooperation with scientists experts users as well as manufacturers all over the world oince the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user friendly direction Our labelling system started with displays in 1992 and is now requested by users and IT manufacturers all over the world For more information please visit www tcodevelopment com HANNspree 3 RECYCLING INFORMATION HANNspree Inc cares about environmental protection strategies and in using manufacturing methods and treatments that lend themselves to conservation and recycling devices at the end of life Our products whenever possible contain recyclable materials which can be recycled into new devices When necessary for operation other materials may be classified as hazardous or poisonous substances We strongly encourage you to research the provided information about recycling this device United State http newyork earth911 org Asia http recycle epa gov tw public public4 2 htm Europe Ireland Company McGrath Environmental Consultants Ltd Contact Person M
18. s McGrath Clodagh Address 20 Lower John Street Cork Ireland Tel 021 4554833 Fax 021 4505805 Norway Company Bergfald amp Co as Contact Person Mr Solev g ystein Address Solavagsvegen 90 EIDSNES NORWAY Code N 6037 Tel 47 40 23 47 05 Fax 47 70 19 40 17 Web Site http www bergfald no bergfald english html United Kingdom Company ARENA Network Contact Person Dr Tillotson Allen Address Bank Buildings Treforest Estate Pontypridd Rhondda Cynon Taff Kindom Post Code CF37 SUR Tel 01443 844001 Fax 01443 844002 Web Site http www arenanetwork org 4 1 SAFETY NOTICE Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Shielded interface cables and AC power cord if any must be used in order to comply with the emission limits The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment It is the responsibilities of the user to correct such interference WARNING To prevent fire or shock hazard do not expose the monitor to rain or moisture Dangerously high voltages are present inside the monitor Do not open the cabinet For all service issues please refer to qualified personnel only PRECAUTIONS Do not use the monitor near water e g near a bathtub washbowl kitchen sink laundry
19. ss Controls Manually set resolution to 1440 X 900 ru is dim too bright or for 19 Wide models or 1280 X1024 for 19 models Please consult your operating system manual for specific instructions Update Video Card driver Picture bounces or wave pattern is present the picture Reposition electrical devices that may cause electrical interference Computer Power Switch should be in the ON position Computer Video Card should be snugly seated in its slot Make sure monitor s video cable is properly connected to the computer Inspect monitor s video cable and make sure none of the pins are bent Make sure computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED The LED should either turn ON or OFF after hitting the CAPS LOCK key The power LED is ON orange but there s no video or no picture Missing one of the primary colors RED GREEN or Inspect the monitor s video cable and make sure that BLUE none of the pins are bent Screen image is not centered Adjust pixel frequency CLOCK and PHASE or press or sized properly hot key AUTO Picture has color defects Adjust color or select color temperature white does not look white Horizontal or vertical Use win 95 98 2000 NT ME XP shut down mode disturbances on the screen Adjust CLOCK and PHASE or perform hot key AUTO HANNspree 19 ERROR MESSAGE amp P
20. tempt to service the monitor by yourself opening or removing covers can expose you to dangerous voltages and other hazards Please refer all service issues to qualified service personnel To ensure satisfactory operation use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 240V AC Min 5A The wall socket shall be installed near the equipment and shall be easily accessible HANNspree D SPEGIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate problem Due to the nature of the fluorescent light the screen may flicker during initial use Turn off the Power Switch and then turn it on again to make sure the flicker disappears You may find slightly uneven brightness on the screen depending on the desktop pattern YOU USE The LCD screen has effective pixels of 99 99 or more It may include blemishes of 0 01 or less such as a missing pixel or a pixel lit all of the time Due to the nature of LCD screens an after image of the previous displayed content may remain if this image has been the displayed for several hours The LCD screen should recover if the image is changed or powered off for several hours If the screen suddenly flashes erratically or the backlighting fails please contact your dealer or service center for repair Do not attempt to repair the monitor yourself HANNspree Thank you for purchasi
Download Pdf Manuals
Related Search