GE TS Series Installation Guide
Contents
1. locking clockwise making sure the fixture should snap into position tab Make sure the locking tab polarity lines match between the is positioned directly below the track and the fixture adapter polarity line Push adapter into track This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This Class A RFLD complies with the Canadian standard ICES 003 Ce DEFR de la classe A est conforme la NMB 003 du Canada Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Fixture intended for commercial use only Use only in non insulated applications GE Lighting 1 888 MY GE LED 1 888 69 43 533 www gelighting com GE Lightin2. GE Lighting Installation Guide Track Fixture Engineering Samples GE LED Track Fixture Track Fixture Samples SKU Product Description Power TBD ENG SAMPLE 2000Im 830 FL 20W TBD ENG SAMPLE 1000Im 830 FL 10W TBD ENG SAMPLE 1500Im 830 FL 15W TBD ENG SAMPLE SPOT 830 20W BEFORE YOU BEGIN Read these instructions completely and carefully FOR USE WITH CEILING MOUNTED TRACK ONLY READ GLOBAL trac eco TRACK INSTALLATION INSTRUCTIONS D2234B FOR GUIDELINES ON TRACK INSTALLATION A WARNING RISK OF ELECTRIC SHOCK Turn power off before inspection installation or removal A CAUTION To reduce risk of fire and electric shock use only with Nordic Aluminum GLOBAL eco GES2 track system imagination at work Input Current Input Voltage Frequency 167mA 120V 60Hz 87 mA 120V 60Hz 125 mA 120V 60Hz 167mA 120V 60Hz IMPORTANT SAFETY INSTRUCTIONS When installing or using this track system basic safety precautions should always be followed including the following a Read all instructions b Do not install this track in damp or wet locations c Do not cut any track sections d Do not install any part of a track system less than 5 feet above the floor e Do not install any luminaire assembly closer than 6 inches from any curtain or similar combustible material f Disconnect electrical power before adding to or changing the configuration of the track g Do not attempt to energize anything othe
3. g Solutions LLC is a subsidiary of the General Electric Company The GE brand and logo are trademarks of the General Electric Company 2014 GE Lighting Solutions LLC Information provided is subject to change without notice All values are design or typical values when measured under laboratory conditions IND129 091114
4. r than ighting track luminaires on the track To reduce the risk of fire and electric shock do not attempt to connect power tools extension cords appliances and the like to the track h Do not connect a track to more than one branch circuit unless the track is constructed so that it can be used with more than one branch circuit Check with a qualified electrician Although the track lighting system may seem to operate acceptably a dangerous overload of the neutral may occur and result in a risk of fire SAVE THESE INSTRUCTIONS For future reference when adding fixtures or changing the track configuration Select Circuit Position The fixture adapter can be used on both GLOBAL eco GES one circuit and GET two circuit track systems An adjustable contact on the fixture adapter allows you to select the circuit position Circuit 1 Contact Circuit 2 1 For one circuit installation no 2 For two circuit installation lift adjustment is required Contact the lower contact to the up is in the down position position with a narrow blade screw driver Fixture Installation CAUTION Fixtures supplied with the GES66 adapter can be used only with GLOBAL eco trac Attempted use on any other track could cause fire and electrical hazard Align locking tab z Rotate with polarity line 1 Hold the adapter below the track Rotate adapter 90 degrees 3 Release the locking tab and the with your thumb on the
Download Pdf Manuals
Related Search