Danby DKC445BL User's Manual
Contents
1. 3 C e To maintain temperatures ranging between 34 F 38 F 1 C 3 C We recommend the thermostat knob be positioned at the 2 00 o clock setting on the graduated blue control dial See Fig 15 e To turn off the refrigerator no cooling rotate the control knob to the 0 position See Fig 14 HELPFUL HINTS ON CONTROLLING TEMPERATURE Keep a thermometer handy adjust temperature control knob accordingly Periodically monitor temperatures inside your cooler adjust as necessary Keep the refrigerator door closed as much as possible to avoid temperature fluctuations CLEANING AND MAINTENANCE AUTOMATIC DEFROSTING There is no need to defrost the refrigerator because ice depositing on the evaporator is defrosted automat ically Ice build up on the evaporator during compressor operation will when the compressor has cycled off defrost automatically Defrost water collects inside the drain trough and passes through the drain outlet in the rear wall into a drain pan situated above the compressor where it evaporates CLEANING THE APPLIANCE Always disconnect the power cord before cleaning and or servicing the appliance Do not use coarse or aggressive cleaning agents as they can damage painted surfaces Clean the exterior cabinet with warm water and a mild detergent Clean the interior with warm water and a mild detergent adding one or two spoonfuls of vinegar After cleaning connect the appliance to power supply SWITCH O2. Owners Manual Glaciere de biere en fut Guide d utilisation Barril Refrigerador Manual del propietario Danby Products Limited Guelph Ontario Canada N1H 6Z9 Danby Products Inc Findlay Ohio USA 45840 DKC445BL 11 00 TABLE OF CONTENTS Before putting appliance into use We care for the environment Tips for energy savings Disposal of worn out appliance Location Instructions for setting up the Chill n Tap Keg Cooler Chill n Tap Keg cooler accessories Warning CO2 can be dangerous Chill n Tap assembly instructions How to replace and empty CO2 cylinder Setting the refrigerator temperature Helpful hints on setting the refrigerator temperature Cleaning and maintenance Changing the direction of the door opening swing Helpful hints to assist you in serving the perfect glass of cold beer Keg sizes Dispensing beer Cleaning beer lines Converting the Chill n Tap Keg Cooler to a basic All Refrigerator Optional accessories available for Keg Cooler and or All Refrigerator Additional information on CO2 Warranty INTRODUCTION Thank you for buying a Danby Millennium appliance This unique appliance is designed to offer you two separate functions The primary function of this appliance is that of a Chill n Tap Draft Beer Dispensing unit When this unit is not being used as a Draft Beer Dispensing unit it s secondary function allows for fast and easy conversion to a compact All Refrigerator app
3. Fire water damage theft war riot hostility acts of God such as hurricanes floods etc SA 7 Service calls resulting in customer education R SS Proof of purchase date will be required for warranty claims so please retain bills of sale In the event warranty service is required present this document to our GA 2 AUTHORIZED SERVICE DEPOT eK N59 A OG DA ed Warranty Service R OG DA e d Canada United States R RY Compacts In Home In Home S e G oe Danby Products Inc x P O Box 669 Findlay Ohio U S A 45839 0669 R 6S Danby Products Limited Telephone 419 425 8627 FAX 419 425 8629 ge S P O Box 1778 Guelph Ontario Canada N1H 629 5 Telephone 519 837 0920 FAX 519 837 0449 et 11 00 Yoa K ODIO RADAR ARCA CADA AS AA
4. condenser evaporator de E Fifth Year dryer and all related tubing will be replaced without charge The purchaser shall pay for all labour and return freight during this four 2 K year 4 period for repair or replacement of any sealed system components Any unit being diagnosed as non functional due to sealed R aN system failure and warranting an exchange during the existing four 4 years will be subject to an appropriate depreciation or user fee SS lt amp including any and all freight charges being levied against the consumer R OG Sr SS To obtain Contact your dealer from whom your unit was purchased or contact your nearest authorized Danby service depot where service D Cs Service must be performed by a qualified service technician If service is performed on the units by anyone other than an authorized service gt LA amp depot or the unit is used for commercial application all obligations of Danby under this warranty shall be at an end R PES The following clause refers to single and double door refrigerators supplied with or without a separate freezer section Nothing within this warranty shall imply TA ZS s KA that Danby will be responsible or liable for any spoilage or damage to food or other contents of this appliance whether due to any defect of the appliance or its R A ek use whether proper or improper o K amp Save as herein provided Danby Products Limited Canada or Danby Products Inc U S A
5. of the red air line hose to the hose barb connection on the keg coupler Secure hose by using the remaining self locking plastic snap on clamp provided use pliers to tighten clamp and assure there are no leaks Installation of the Beer Line Hose to the Keg Coupler IMPORTANT NOTICE The black rubber washer provided must be installed inside the wing nut before connecting the beer line to the keg coupler Remove the black rubber protective cap located on top of the keg coupler and screw the wing nut with rubber washer onto the keg coupler hand tighten firmly Making the connection between the Keg Coupler and Beer Keg Before making opening connection between the keg coupler and beer keg make sure the beer tower faucet is in the closed position faucet handle straight back To engage the tank connection pull the keg coupler handle out and push down until it locks into position Listen for positive click of the pull handle in the final downward position See Fig 10 Opening the CO2 Cylinder Main Valve Before opening the main valve located on top of the CO2 cylinder Make sure the secondary shut off valve located on the lower stem pipe of the regulator is in the closed position See Fig 11 NOTE When the secondary valve handle is positioned Horizontal east west the valve is closed 21 When the secondary valve handle is positioned Vertical north south the valve is open To open the main CO2 cylinder
6. or injury to persons GROUNDING INSTRUCTIONS For your personal safety this appliance must be grounded In the event of a malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current This appliance is equipped with a power cord having an equipment grounding conductor and grounding plug The plug must be plugged into an appropriate wall outlet that is installed and grounded in accordance with all existing local codes and ordinances Consult a qualified electrician or serviceman if the grounding instructions are not clearly understood or if doubt exist as to whether your electrical wall outlets are properly grounded LOCATION e Selecting the proper location will ensure peak performance levels of your appliance Choose a location where the unit will not be exposed to direct sunlight and away from heat emitting sources This appliance is designed for indoor use only and should not be used outdoors e This appliance is inclusive of an in wall static type condenser and should not be built in recessed unless adequate ventilation is provided to maintain proper cooling minimum 2 3 inches clearance required on all sides e If the unit as a Keg Cooler application is to be built in remember this will hamper 1 Removal of the CO2 cylinder when it needs to be re filled 2 Reading Monitoring Adjustment of the low pressure CO2 regulator to maintain proper operating pr
7. there are no other warranties conditions representations or guar R SS antees express or implied made or intended by Danby Products Limited or its authorized distributors and all other warranties conditions representations or ORE amp guarantees including any warranties conditions representations or guarantees under any Sale of Goods Act or like legislation or statute is hereby expressly R LR excluded Save as herein provided Danby Products Limited Canada or Danby Products Inc U S A shall not be responsible for any damages to persons or SIS 60 property including the unit itself howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit the 6 9 6 purchaser does hereby agree to indemnify and save harmless Danby Products Limited from any claim for damages to persons or property caused by the unit Gos E aS GENERALPROVISIONS RE K No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following amp S 1 Power Failure 6 NG 2 Damage in transit or when moving the appliance SA amp 3 Improper power supply such as low voltage defective house wiring or inadequate fuses R 6S 4 Accident alteration abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating conditions S KI extremely high or low room temperature A ES 5 Use for commercial or industrial purposes SS NG 6
8. valve slowly turn the main valve counter clockwise until fully open You will notice the needles on both gauges start to climb Adjusting the CO2 Regulator There are two pressure gauges on the CO2 regulator See Fig 12 The upper gauge 1 monitors LOW internal keg pressure and must be adjusted to the correct operating pressure of 10 12psi lbs The lower gauge 2 monitors HIGH CO2 cylinder pressure and is not adjustable The high pressure gauge also acts as a fuel gauge to let you know when the C02 cylinder needs re filling IMPORTANT The internal operating pressure of the beer keg should be adjusted and maintained between 10 12psi lbs To adjust the low pressure gauge e Using an adjustable wrench release the adjustment lock nut 3 See Fig 12 Using a flat screwdriver turn the regulator adjustment screw 4 See Fig 12 Clockwise rotation of the adjustment screw will increase low pressure Counter clockwise rotation of the adjustment screw will decrease low pressure e When the required operating pressure is attained retighten the adjustment lock nut 3 e You are now ready to serve cold beer Secondary Shut off Fig 9 Fig 10 Fig 11 Valve Fig 12 HOW TO REPLACE AN EMPTY CO2 CYLINDER Close the main cylinder valve A by turning ina 9 Readjust regulator pressure D if necessary clockwise direction See Fig 13 Close the secondary shut off valve C by turning to horizontal
9. 263 2629 ADDITIONAL INFORMATION ON CO2 Afully charged 5lb CO2 cylinder will service approx Quantity Keg Size 20 30 Liter Kegs 1 4 Barrels 25 20 Liter Kegs 1 6 Barrels For the location of a CO2 supplier in your area re fills please look in your Yellow Page telephone directory under OXYGEN suppliers 12 IT HR IR IN HR IRR A AA HAS ef w 6S Danby LIMITED PRODUCT WARRANTY 69 O 34 amp This quality product is warranted to be free from manufacturer s defects in material and workmanship provided that the unit is used under the normal operating D SS conditions intended by the manufacturer ES R This warranty is available only to the person to whom the unit was originally sold by Danby or by an authorized distributor of Danby and is non transferable X KA TERMS OF WARRANTY 6 9 6 Plastic parts ie evaporator door door rails covers and trays are warranted for thirty 30 days only from purchase date with no extensions provided Cn XS First Year During the first year 1 any electrical parts of this product found to be defective including any sealed system units will be repaired or PS SA amp replaced at warrantor s option at no charge to the ORIGINALpurchaser Consumable parts ie light bulbs are not warranted or guar R A anteed for any length of time amp Second Through During the next four years 4 any part of the sealed system found to be defective consisting of compressor
10. E CO2 CYLINDER VENTILATE AND LEAVE THE ROOM IMMEDIATELY CO2 gas cylinders should be stored in the coolest part of the establishment preferably at 70 F 21 C and must always be securely fastened in an upright position CHILL N TAP ASSEMBLY INSTRUCTIONS Remove Worktop Using a Phillips Screwdriver remove the three screws located on the front underside edge of the worktop and the three screws located at the rear back side of the worktop See Fig s 1 amp 2 Remove the worktop from the cabinet and position the worktop on top of the cabinet so that the front corners are staggered across the front corners of the cabinet Installation of Top Rail Attach the chrome rail to the work top using four self tapping screws from the underside of the worktop through the pre drilled holes attach the front ends of the rail first Re Install Worktop Install the front of the worktop onto the cabinet then lower the rear side of the worktop over the backside of the cabinet Secure using the same screws removed earlier the smaller screws at the front the larger screws at the rear Installation of CO2 Cylinder Support Install the cylinder support onto the four studs located on the exterior back wall of the cabinet no tools required Align the holes in the cylinder support with the studs and push down firmly See Fig 3 Installation of CO2 Cylinder Install your fully charged CO2 cylinder into the support stand I
11. FF AND OR DISCONNECT THE APPLIANCE WHEN NOT IN USE If you do not intend to use the appliance for long periods of time vacations set the thermostat knob to the 0 off position and disconnect the power cord Take out all foods and clean the appliance Leave the door slightly open to reduce mold mildew from accumulating inside the cabinet CHANGING THE DIRECTION OF THE DOOR OPENING SWING If you find the direction of the door swing on your appliance inconvenient you can change it to the opposite side Simply follow the steps listed below Lay the unit on it s back Remove the adjustable leveling leg from the lower right hinge Remove two 2 screws from the lower door hinge Open the main door and pull down until the door releases from the upper door hinge pin Remove the plastic door plug cap from the top left side of the main door Re install plastic door plug cap to the top right side of the main door Remove unscrew the upper door hinge pin right side cabinet Re install the upper door hinge pin left side cabinet Position the main door back on the cabinet and push up until the top hinge pin is inserted into the top of the door 9 7097 ge NS ES Re install the lower door hinge to the left side of the cabinet using the same screws removed earlier Align the main door on the cabinet before tightening the lower hinge screws Re install the leveling leg back into the lower hinge Return the unit back to the upright po
12. Hose Plug located exterior rear cabinet 1 Plastic Drip Tray 2 piece WARNING CO2 CAN BE DANGEROUS WARNING CO2 Cylinders when charged contain high pressure compressed gas which can be hazardous if not handled properly Read and understand the following procedures for C02 cylinders before installation 1 Always connect CO2 gas cylinder to a regulator Failure to do so could result in an explosion with possible death or injury when the cylinder valve is opened Never connect C02 gas cylinder directly to beer keg Always secure C02 gas cylinder in an upright position Always keep CO2 gas cylinder away from heat Never drop or throw CO2 gas cylinder Always check the D O T Department of Transport test date located on the neck of the cylinder before installation If over five 5 years do not use return the gas cylinder to gas supplier Never connect a product container unless there are two 2 safety mechanism s in the pressure system a One at or on the CO2 regulator the regulator supplied with this unit is inclusive of such a safety mechanism b One at or on the product container coupler or in the pressure gas line the keg coupler supplied with this unit is inclusive of such a safety mechanism 8 Always ventilate area after any leakage of CO2 If it becomes difficult to breathe and or your head starts to ache abnormal concentrations of carbon dioxide CO2 may be present in the area CLOSE THE MAIN VALVE ON TH
13. MPORTANT NOTICE ALWAYS EXERCISE EXTREME CAUTION WHEN HANDLING PRESSURIZED C02 CYLINDERS Installation of C02 Regulator Attach the CO2 Regulator to the C02 cylinder by screwing the regulator nut onto cylinder valve and tighten snug using an adjustable wrench Installation of C02 Air Line Hose to Regulator Attach one end of the red air line hose to the hose barb connection on the CO2 regulator Secure hose by using one of the two self locking black plastic snap on clamps provided use pliers to snap the clamp tight to assure that there are no leaks See Fig 5 Fig 1 Fig 2 Fig 3 Fig 4 8 10 11 12 CHILL N TAP ASSEMBLY INSTRUCTIONS CON T Installation of CO2 Air Line inside Cabinet Remove rubber plug located at the exterior top right hand corner of the cabinet store this plug in a safe place it will be required when converting your unit back to a basic refrigerator Insert the open end of the air line into the cabinet through the opening vacated by plug See Fig 6 Remove the Chill n Tap Cabinet Plug located on top of worktop Firmly grasp the cabinet Chill n Tap plug twist and pull upward store this plug in a safe place it will be required when converting your unit back to a basic refrigerator Installation of the Beer Tower Quick Connect Locking Bayonet Insert the locking bayonet into the opening on the worktop Align the F indicated on top of the bayone
14. Model Mod le Modelo DKC445BL For service contact your nearest service depot or call 1 800 26 Danby 1 800 263 2629 to recommend a depot in your area En cas de r paration veuillez contacter votre service apres vente le plus pres ou communiquez au 1 800 26 Danby 1 800 263 2629 pour connaitre le service apres vente le plus proche Para obtener servicio comuniquese con el establecimiento de servicio m s cercano o llame al 1 800 26 Danby 1 800 263 2629 para que le recomendemos un establecimiento de su zona Chill nlap Keg Cooler The model number can be found on the serial plate located on the back panel of the unit All repair parts available for purchase or special order when you visit your nearest service depot To request service and or the location of the service depot nearest you call the TOLL FREE NUMBER When requesting service or ordering parts always provide the following information Product Type e Model Number e Part Description Glaci re de bi re en fut Chill n lap Le num ro du mod le se trouve sur la plaque d identification situ e sur le panneau arri re de l appareil Il est possible d acheter les pi ces de rechange ou de les obtenir par commande sp ciale en vous rendant votre service apr s vente le plus proche Pour effectuer des r parations ou obtenir l adresse du service apr s vente le plus proche veuillez composer le NUM RO SANS FRAIS Po
15. before tapping Prior to tapping the keg ensure the beer faucet is in the off position e Completely remove the dust cover identification cap from the beer keg e Check that the keg coupler handle is in the up off position See Fig 9 Insert the keg coupler into the locking neck of the beer keg and apply a turn clockwise to lock into position e Pull keg coupler handle out and downward until it locks into position See Fig 10 This activates both the beer and CO2 pressure line The keg is now tapped and ready to draw beer CLEAN BEER GLASSES Keeping your glassware beer clean is the key to serving good draught beer To achieve this e Maintain strict sanitary conditions in the glass washing area e Never wash glassware with utensils or dishes used to serve food Food particles and or residue can effect the quality taste of draught beer Do not use regular liquid household dish washing detergents for glassware They are fat based and will leave a slight oily film on the glass This causes beer to go flat quickly Use a detergent designed specifically for beer glass cleaning lt must be low suds odor free and non fat Avoid drying glassware with towels as they tend to leave traces of lint on the surface of the glass e We recommend that you use beer glassware only for beer Dairy and other food products leave a residue which can effect the quality taste of the draught 10 KEG SIZES There are two 2 standard size bee
16. east west position on lower stem pipe See Fig 13 Remove the air line clamp and hose from the regulator Remove the regulator assembly E from empty cylinder See Fig 13 Remove dust cap from new and or replacement CO2 cylinder Re attach regulator assembly E to new replacement cylinder See Fig 13 Re attach the air line hose to regulator barb connection and secure with clamp Slowly open main valve A all the way See Fig 13 between 10 12 psi lbs 10 Open the secondary shut off valve C by turning to vertical north south position on lower stem pipe SETTING THE REFRIGERATOR TEMPERATURE The temperature of the refrigerator compartment is controlled by adjusting setting the thermostat con trol knob located on the ceiling of the refrigerator cabinet To start the refrigerator and achieve maximum cooling quickly e Turn the temperature control knob using a coin or screwdriver clockwise to the furthest maximum setting on the darker blue section of the graduated control dial See Fig 14 e Allow the refrigerator to run at this setting for 3 4 hours e When maximum cooling is achieved turn back the temperature control knob setting to the 2 00 o clock position on the graduated blue control dial See Fig 15 e Correct cooling temperature is a key factor to consider in storing and dispensing draught beer e Optimum temperature for serving draught beer is between 34 F 38 F 1 C
17. essure INSTRUCTIONS FOR SETTING UP THE CHILL N TAP KEG COOLER Please read and understand these instructions thoroughly before attempting assembly installation and operation of your Chill n Tap Keg Cooler Remove and inspect all internal accessories components supplied with this unit are present and in good condition A check list of accessories is listed below for reference purposes In the event any accessory is missing and or not in good condition please contact our after sales service department and ask for customer assistance TOLL FREE NUMBER 1 800 26 DANBY CHILL N TAP ACCESSORIES included with this unit 1 Chrome Rail for attachment to Worktop 4 Self Tapping Screws to attach chrome rail 1 CO2 Cylinder Support Stand 1 CO2 Cylinder empty 1 CO2 Regulator high low pressure gauges 1 CO2 Air Line Hose red 2 CO2 Air Line Hose Connectors black 1 Beer Keg Coupler 1 Beer Tower Unit complete with faucet hose and wing nut 1 Rubber Washer to be installed inside wing nut 1 Beer Tower Quick Connect Bayonet Attachment beer tower installation 4 Machine Screws to attach bayonet to beer tower 1 Gasket beer tower base 1 Pull Handle beer tower faucet 1 Beer Keg Stand required for 30 liter keg installations only 1 Protective Plate refrigerator cabinet floor 2 Cantilever Wire Shelves conversion to all refrigerator application 1 Chill n Tap Exterior Cabinet Plug located on worktop 1 CO2 Air Line
18. lication This refrigerator is for domestic use only and is intended for storing fresh foods at temperatures higher than 32 F 0 C Model Number Serial Number Date of Purchase Dealer s Name and Address This information will be required if your unit requires servicing and or for general inquiries To contact a Customer Service Representative call Danby TOLL FREE 1 800 26 Danby CAREFULLY READ AND SAVE THESE INSTRUCTIONS These instructions for use are intended for the user They describe the appliance and correct installation and operating procedures for safe use IMPORTANT NOTICE Beer is easily available with Danby s new Keg Cooler Refrigerator however it is not intended to be available to people under the legal age to consume beer One of the options Danby offers is a lock so that access to the ice cold beer can be limited Danby does not assume liability for the unlawful use or consumption of the beer DON T DRINK AND DRIVE NOTE This appliance was carefully packed and thoroughly inspected before leaving our factory Responsibility for its safe delivery was assumed by the carrier upon acceptance of the shipment Claims for loss or damage sus tained during transit must be made directly to the carrier 4 BEFORE PUTTING APPLIANCE INTO USE e Before connecting the appliance to any electrical power supply leave it standing upright for about 2 hours This will reduce the possibility of malfunctions in the cooling system d
19. linder Close the secondary shut off valve horizontal position on the regulator stem pipe Close the connection between the beer keg and the keg coupler by pulling and lifting the handle into the upright position Disconnect both the beer line and CO2 air line from the keg coupler Remove the beer keg and keg stand from the cabinet Disconnect the air line from the CO2 cylinder Remove the CO2 air line from the cabinet Install the air line rear cabinet plug Remove the beer tower assembly from the cabinet by grasping the center of the tower making a turn counter clockwise and lift pull the beer line through the top of the cabinet Install the Chill N Tap cabinet plug worktop Install the 2 cantilever wire shelves onto the factory installed cantilever support brackets located on the rear wall of the refrigerator cabinet Adjust the refrigerator temperature as required The conversion process is now complete Please make sure all Chill N Tap accessories removed are stored in a safe place for future use OPTIONAL ACCESSORIES FOR CHILL N TAP KEG COOLER Description Part No Beer Faucet Lock 445 7703 Beer Line Cleaning Kit 445 5571 OPTIONAL ACCESSORIES FOR ALL REFRIGERATOR Description Part No Crisper Drawer 452 1C Crisper Cover 452 28 Additional Wire Cantilever Shelf 452 33 For more details on purchasing any of the above listed accessories please contact our after sales service department at 1 800 26 DANBY 1 800
20. r kegs that can be used in your Chill N Tap Keg Cooler 30 Liter Keg 1 4 Barrel yields 3 1 2 cases 10560zs of beer Keg Weight 91lbs Full 20 Liter Keg 1 6 Barrel yields 2 1 2 cases 7040zs of beer Keg Weight 54lbs Full Note The keg stand is required only when using the 30 liter size beer keg DISPENSING BEER IMPORTANT NOTICE Beer is easily available with Danby s new Keg Cooler Refrigerator however it is not intended to be avail able to people under the legal age to consume beer One of the options Danby offers is a lock so that access to the ice cold beer can be limited Danby does not assume liability for the unlawful use or con sumption of the beer PLEASE DON T DRINK AND DRIVE e Keep beer keg refrigerated at all times Never let beer lines empty or allow them to dry out e Rinse the beer glass with fresh cold water before pouring e Hold glass at a 45 angle hold steady when 2 3 full start to straighten glass and top it off e When beer is dispensing through the faucet condensation may form on the outer surface of the faucet This is a normal condition and cannot be avoided This is caused by temperature differentials between cold beer flowing across the warmer ambient surfaces of the inner faucet e Always make sure the faucet handle is pushed fully back closed to prevent excess dripping A beer faucet lock kit for the purpose of limiting access is readily available and can be purchased through our after sale
21. s service department at 1 800 26 DANBY 1 800 263 2629 CLEANING BEER LINES Why do dispensing lines have to be cleaned Beer lines have to be cleaned because a scale called calcium oxalate commonly referred to as beer store forms on the fittings lines and taps Beerstore if not completely removed in a cleaning process will leave an unsanitary surface that can har bour microorganisms Line cleaning with the proper equipment and chemical eliminates the build up of beerstore protecting the integrity of the product Microorganisms or bacteria will grow very quickly if a sanitary environment is not maintained causing off flavours or shorten the shelf life of beer Regular cleaning assures that bacteria does not have the opportunity to reach levels which affect the quality taste of the beer Line cleaning should be done on a regularly scheduled basis approximately every 6 weeks A standard cleaning kit will perform approximately eight 8 scheduled line cleanings Line cleaning kits are readily available and can be purchased through our after sales service department For more information please call 1 800 26 DANBY 1 800 263 2629 11 CONVERTING THE CHILL N TAP KEG COOLER TO A BASIC ALL REFRIGERATOR The Chill N Tap Keg Cooler is designed to offer you quick and easy conversion from a beer dispensing unit to a basic compact All Refrigerator application Simply follow the below steps Close the main valve on the CO2 cy
22. sition Allow the unit to stand 30 minutes before switching the unit on HELPFUL HINTS TO ASSIST YOU IN SERVING THE PERFECT GLASS OF COLD BEER STORAGE AND HANDLING e Draught Beer should be treated as a food product In most instances draught beer is not pasteurized It is very important that you store and handle it properly e Draught Beer should be immediately stored in a refrigerated cabinet Draught Beer products have a shelf life which on average is 30 days after the keg is tapped By keeping the beer keg pressurized with CO2 the shelf life can be extended 60 days Beer Kegs should be stored refrigerated separately from other food products It is very important that food not be stored near or on the beer keg BEER TEMPERATURE e Correct temperature is a key factor to consider in storing and dispensing draught beer e Beer can freeze so it is important to select and maintian proper operating temperatures inside the refrigerator cabinet Optimum temperatures for serving cold beer are 34 38 F 1 3 C e Temperatures too cool or too warm may cause flavour loss off taste and dispensing problems CO2 PRESSURE e Periodically monitor the pressure regulators to ensure applied operating pressures remain constant 10 12psi lbs e Always keep equipment in good repair TAPPING KEG Do not agitate kegs unnecessarily If excessive agitation occurs during transportation allow keg to settle for 1 2 hours
23. t has spoiled and therefore dangerous to consume e Always disconnect the appliance from the power supply before cleaning and or attempting repairs servicing WARNING Repairs should be performed by qualified service personnel only e Do not defrost this appliance using other electric appliances i e hair dryer and never attempt to scrape remove ice frost from the evaporator cold plate with sharp objects e The rating plate containing Model No Serial No and other technical data specific to this unit is located on the exterior rear wall of the refrigerator cabinet DISPOSAL OF WORN OUT APPLIANCES e When your appliance finally wears out dispose of it in a safe and harmless manner If you have bought this appliance to replace an old one equipped with a door lock that cannot be opened from the inside lock bolt make sure the lock is removed disabled or destroyed before discarding This will make it impossible for children to accidentally lock themselves inside the appliance and suffocate e The refrigerator system of this appliance is filled with refrigerant and insulating substances which should be treated and processed separately Call your nearest service agent or specialized servicing center If you are unable to locate one contact your local authorities for proper disposal instructions Be careful not to damage the any of the refrigeration lines of the appliance WARNING Instructions pertaining to the risk of fire electric shock
24. t with the right front corner of the worktop push and 1 4 turn clockwise The F represents the final FRONT installation position of the beer tower at the 6 00 o clock position Installation of the Beer Tower Gasket Position the rubber beer tower gasket directly on top of the bayonet aligning all four holes in the gasket with the four holes on the bayonet Installation of the Beer Tower Unravel the beer line hose from the tower and insert the beer line and wing nut through both the gasket and bayonet This will require a little maneuvering by positioning folding the wing nut together with the beer line in a north south direction and pushing it through the hole Align the four holes in the base of the beer tower gasket and bayonet The beer faucet should be aligned with the F on the bayonet and facing the front Fig 7 13 14 15 of the cabinet 6 00 o clock position Using a Phillips Screwdriver attach the beer tower to the bayonet using four machine screws provided and tighten firmly To remove unlock the beer tower assembly from the cabinet grasp the tower and 1 4 turn counter clock wise until it stops and lift This allows quick and easy removal of the beer tower assembly when converting the unit from the keg cooler application to the all refrigerator application Installation of the Beer Tower Faucet Handle Screw the black faucet handle clockwise onto the beer tower faucet hand
25. tighten only Installation of the Protective Plate To prevent unnecessary damage marring to the floor of the refrigerator cabinet the protective plate should always be installed when the keg stand is being used The protective plate also makes installation and removal of the keg stand easier Installation of the Beer Keg Position the keg stand directly in front of the open refrigerator cabinet Using proper lifting technique using keg handles only carefully lift the beer keg onto the keg stand See Fig 7 NOTE The keg stand is required when using 30 Liter 1 4 barrel kegs only To install the beer keg and stand inside the refrigerator cabinet brace your knees behind the keg stand and grasp the keg stand handles Lift the front of the keg stand just enough so that the front edge of the stand is resting on the front edge of the refrigerator cabinet See Fig 8 Grasp the keg stand front handles and care fully slide the keg stand all the way into the refrigerator cabinet 16 17 18 19 20 CHILL N TAP ASSEMBLY INSTRUCTIONS CON T Installation of the Keg Coupler IMPORTANT NOTICE Make sure the black pull handle of the keg coupler is in the upward closed position before installing on the beer keg See Fig 9 Insert the keg coupler into the locking neck of the beer keg and apply a 1 4 turn clockwise to lock into position Installation of the CO2 Air Line Hose to the Keg Coupler Attach the open end
26. ue to transport handling e Clean the appliance thoroughly both interior and exterior See Cleaning and Maintenance WE CARE FOR THE ENVIRONMENT e Our products use environmentally friendly recyclable materials To this end individual packaging materials are clearly identified with a recycling symbol Always use proper disposal methods e When any appliance finally wears out always use safe and proper disposal methods 1 e use authorized land fill sites only TIPS FOR ENERGY SAVINGS e Try not to open the door too often especially when the weather is hot and humid Once you open the door close it as soon a s possible Every now and then check the appliance to make sure it is receiving sufficient ventilation adequate air circulation behind the appliance e Set the thermostat from higher to lower settings as soon as possible this will depend on loaded conditions and ambient temperatures etc e Before loading the appliance with fresh foods make sure they are cooled to ambient room temperature excluding soups e If the door gasket is damaged or the door seal is poor energy efficiency is lost and energy consumption is substantially higher To restore energy efficiency replace the door gasket and or adjust the door IMPORTANT e This appliance must be connected to a properly grounded electrical outlet see Grounding Instructions e If food or beverage has a strange smell or color throw it away because it is likely that i
27. ur effectuer des r parations ou commander des pi ces de rechange veuillez donner les renseignements suivants Type de mod le Num ro du mod le Description des pi ces Barril refrigerador Chill n Tap El numero de modelo se encuentra en la placa de serie ubicada en el tablero posterior de la unidad Puede comprar todos los repuestos o hacer un pedido especial visitando el establecimiento de servicio m s cercano a su domicilio Llame al TEL FONO GRATUITO para obtener servicio de mantenimiento o la direcci n del establecimiento de servicio m s cercano a su domicilio Siempre al solicitar servicio de mantenimiento o hacer un pedido de repuestos debe suministrar la siguiente informaci n Tipo de artefacto N mero de modelo Descripci n del repuesto Danby Products Limited Guelph Ontario Canada N1H 6Z9 Printed in China P R C Danby Products Inc Findlay Ohio USA 45840 OWNER S MANUAL MANUEL D UTILISATION MANUAL DEL PROPIETARIO Model Mod le Modelo DKC445BL CAUTION Read and follow all safety rules and operating instructions before first use of this product PRECAUTION Veuillez lire attentivement les consignes de securite et les instructions d utilisation avant l utilisation initiale de ce produit PRECAUCION Lea y observe todas las reglas de seguridad y las instrucciones de operacion antes de usar este producto por primera vez Danby Chill niop Keg Cooler
Download Pdf Manuals
Related Search