Cisco Systems ONS 15600 User's Manual
Contents
1. Service State Identifies the autonomously generated state that gives the overall condition of the port Service states appear in the format Primary State Primary State Qualifier Secondary State e IS NR In Service and Normal The port is fully operational and performing as provisioned e OOS AU AINS Out Of Service and Autonomous Automatic In Service The port is out of service but traffic is carried Alarm reporting is suppressed The ONS node monitors the ports for an error free signal After an error free signal is detected the port stays in OOS AU AINS state for the duration of the soak period After the soak period ends the port service state changes to IS NR e OOS MA DSBLD Out of Service and Management Disabled The port is out of service and unable to carry traffic e OOS MA MT Out of Service and Management Maintenance The port is out of service for maintenance Alarm reporting is suppressed but traffic is carried and loopbacks are allowed SyncStatusMsg Allows you to view the incoming synchronization status message by clicking Show e PRS Primary reference source Stratum 1 e STU Sync traceability unknown e ST2 Stratum 2 e ST3 Stratum 3 e ST3E Stratum 3E e SMC SONET minimum clock e ST4 Stratum 4 e TNC Transit node clock e DUS Do not use for timing synchronization e RES Reserved quality level set by user Enable Sync Messages Enables2. ONS 15454 or ONS 15327 e Yes checked e No unchecked Send Do Not Use When checked sends a DUS do not use message on the S1 byte e Yes checked e No unchecked default BLSR Ext Byte Chosen extended byte carries information that governs BLSR protection switches e K3 e 72 e E2 e FI Admin State Sets the port service state unless network conditions prevent the change e IS Puts the port in service The port service state changes to IS NR e IS AINS default Puts the port in automatic in service The port service state changes to OOS AU AINS e OOS DSBLD Removes the port from service and disables it The port service state changes to OOS MA DSBLD e OOS MT Removes the port from service for maintenance The port service state changes to OOS MA MT AINS Soak Sets the automatic in service soak period Duration of valid input signal in hh mm format after which the card becomes in service IS automatically 0 to 48 hours in 15 minute increments Type Defines the port as SONET or SDH Enable Sync Msg and Send Do Not Use must be disabled before the port can be set to SDH SONET default e SDH I February 2008 Cisco ONS 15600 Procedure Guide R5 0 E Chapter11 Change Card Settings HI NTP E66 Modify Line and Status Thresholds for Optical Ports Table 11 2 Heading OC N Card Line Settings continued Description Options
3. c Click Refresh to view or modify the thresholds for each selection Cisco ONS 15600 Procedure Guide R5 0 I February 2008 EN Chapter11 Change Card Settings HI NTP E66 Modify Line and Status Thresholds for Optical Ports Table 11 3 OC N Threshold Options Line Section and Path Heading Description Options Port Port number 1 16 for an OC 48 card 1 4 for an OC 192 card CV Coding violations Numeric Defaults 15 min 1 day Line e 21260 212600 OC 48 Near and Far End e 85040 850400 OC 192 Near and Far End Section e 10000 100000 Near End 0 0 Far End e 10000 500 OC 192 Near and Far End Path e 15 125 OC 48 OC 192 Near and Far End ES Errored seconds Numeric Default 15 min 1 day Line e 87 864 Near and Far End Section e 500 5000 Near End 0 0 Far End Path e 12 100 OC 48 OC 192 Near and Far End SES Severely errored seconds Numeric Defaults 15 min 1 day Line e 1 4 Near and Far End Section e 500 5000 Near End 0 0 Far End Path e 3 7 OC 48 OC 192 Near and Far End SEFS Severely errored framing seconds Numeric Defaults 15 min 1 day Section e 500 5000 Near End 0 0 Far End Cisco ONS 15600 Procedure Guide R5 0 uau February 2008 l Chapter 11 Change Card Settings Table 11 3 Heading NTP E66 Modify Line and Status Thresholds for Optical Ports OC N Threshold Options Line Section and Path continued Descri
4. synchronization status messages S1 byte which allow the node to choose the best timing source e Yes checked default e No unchecked Step6 Click Apply Cisco ONS 15600 Procedure Guide R5 0 February 2008 l Chapter11 Change Card Settings NTP E66 Modify Line and Status Thresholds for Optical Ports W Step7 Click the Thresholds subtab The default selection is Near End 15 Min and Line Figure 11 1 Figure 11 1 Provisioning Thresholds for the OC 48 Card zox File Edit View Tools Help ala a sje el gt lel ielsie l interop 441 slot 11 OC1 Eqgpt 0C192_4 Status Standby State IS Alarms Conditions History Circuits Provisioning Maintenance Performance _Line NearEnd 15Min Line SONET Thresholds Port cv Es ses Fe uas Psc Psp Psc w PsD w ppl SONETSTS T 85040 87 1 10 3 a 300 a 300 Alarm Behavior 2 85040 87 1 10 3 1 300 1 300 Reset 3 85040 87 1 10 a 1 300 1 300 E 4 85040 87 m 3 a 300 1 300 Directions Intervals pues G NearEnd C 15Min Line C Path Refresh C FarEnd C 1 Day C Section C Physical o oO S NET CKT SS Step8 As needed complete the following a Click Line Section Path or Physical to provision the line section path and physical options in Table 11 3 for each OC N port b Change the selection to Near End Far End 15 Min 1Day as necessary
5. 16 for an OC 48 card 1 4 for an OC 192 card LBC HIGH Laser bias current maximum Default 15 min 1 day 150 percent LBC LOW Laser bias current minimum Default 15 min 1 day 50 percent OPT HIGH Optical power transmitted maximum Default 15 min 1 day 120 percent OPT LOW Optical power transmitted minimum Default 15 min 1 day 80 percent OPR HIGH Optical power received maximum Default 15 min 1 day 200 percent OPR LOW Optical power received minimum Default 15 min 1 day 50 percent Set OPR Setting the optical power received OPR establishes the received power level as 100 If the receiver power decreases then the OPR percentage decreases to reflect the loss in receiver power For example if the receiver power decreases 3 dBm the OPR decreases 50 Click Apply amp Note See Chapter 7 Manage Alarms for information about the Alarm Behavior tab including alarm profiles and alarm suppression Stop You have completed this procedure Purpose This procedure provisions a port on an OC N card for SDH Tools Equipment None Prerequisite Procedures None Required As Needed As needed Onsite Remote Onsite or remote Security Level Provisioning or higher Complete the DLP E26 Log into CTC task on page 16 39 at the node where you want to change the settings If you are already logged in continue with Step 2 Double click the OC N card where you want to provision a port for SDH Click t
6. MT In Service and Normal Out of Service and Management Maintenance Stop You have completed this procedure Cisco ONS 15600 Procedure Guide R5 0 February 2008 l
7. dmin State Original Service State Next Service State IS OOS AUMA MT amp UEQ OOS AU UEQ Out of Service and Autonomous Out of Service amp Management Maintenance and Autonomous Unequipped Unequipped IS OOS AUMA MEA amp MT OOS AU MEA Out of Service and Autonomous Out of Service and Management Mismatched Equipment and Autonomous Mismatched Equipment Maintenance IS OOS MA MT IS NR Out of Service and In Service and Normal Management Maintenance OOS MT OOS AU MEA OOS AUMA MT amp UEQ Out of Service and Out of Service and Autonomous Autonomous Mismatched Equipment Management Maintenance and Unequipped Cisco ONS 15600 Procedure Guide R5 0 I February 2008 TEEN Chapter11 Change Card Settings HE NTP E125 Change Card Service State Table 11 5 Cisco ONS 15600 Card State Transitions continued Admin State Original Service State Next Service State OOS MT OOS AU AINS amp UEQ OOS AUMA MT amp UEQ Out of Service and Autonomous Auto Out of Service and Autonomous In Service and Unequipped Management Maintenance and Unequipped OOS MT OOS AU AINS amp MEA OOS AUMA MEA amp MT Out of Service and Autonomous Auto Out of Service and Autonomous In Service and Mismatched Equipment Management Mismatched Equipment and Maintenance OOS MT OOS AU UEQ OOS AUMA MT amp UEQ Out of Service and Out of Service and Autonomous Autonomous Unequipped Management Maintenance and Unequipped OOS MT IS NR OOS MA
8. e settings If you are already logged in continue with Step 2 Step2 Complete the NTP E69 Back Up the Database procedure on page 14 4 Step3 On the shelf graphic double click the OC N card that you want to provision The card view appears Step4 Click the Provisioning gt Line tabs Click Provisioning gt Optical gt Line tabs for the ASAP card Step5 As needed provision the options in Table 11 2 for each OC N port Table 11 2 OC N Card Line Settings Heading Description Options Port Identifies the port number e For an OC 48 card 1 16 e For an OC 192 card 1 4 e For an ASAP card up to 16 ports denoted by 4PIO module followed by port number Example 1 3 1 denotes the third port on 4PIO Module 1 Port Name Provides the ability to assign the User defined name can be up to 32 specified port a name alphanumeric special characters blank by default SF BER Sets the signal fail bit error rate e 1E 3 e 1E 4 default e 1E 5 Cisco ONS 15600 Procedure Guide R5 0 rite E February 2008 l Chapter11 Change Card Settings NTP E66 Modify Line and Status Thresholds for Optical Ports W Table 11 2 OC N Card Line Settings continued Heading Description Options SD BER Sets the signal degrade bit error rate e 1E 5 e 1E 6 e 1E 7 default e 1E 8 e 1E 9 Provides Sync Indicates that the port has been Read only provisioned as a network element timing reference on another node ONS 15600
9. he Provisioning gt Line tabs In the Type field specify the port and choose SDH Click Apply E Cisco ONS 15600 Procedure Guide R5 0 February 2008 l Chapter 11 Change Card Settings Step 6 NTP E125 Change Card Service State W You can repeat Steps 4 and 5 for any other ports on that card Stop You have completed this procedure NTP E125 Change Card Service State Purpose This procedure changes card service state Tools Equipment None Prerequisite Procedures Chapter 2 Install Cards and Fiber Optic Cable Required As Needed As needed Onsite Remote Onsite or remote Security Level Provisioning or higher Step 1 Complete the DLP E26 Log into CTC task on page 16 39 at the node where you want to change the card service state Step2 Click the Inventory tab Step3 Click Admin State for the card you want to change and choose an Admin state from the drop down list IS In Service or OOS MT Out of Service Maintenance Step4 Click Apply Step5 If an error message opens indicating that the card state cannot be changed from its current state click OK Table 11 5 lists possible card service state transitions based on the Admin State chosen For more information about the enhanced state model and card state transitions refer to the Administrative and Service States appendix of the Cisco ONS 15600 Reference Manual Table 11 5 Cisco ONS 15600 Card State Transitions A
10. ion a Multirate PPM page 11 2 Required As Needed Required Onsite Remote Onsite or remote Security Level Provisioning or higher Step 1 Complete the DLP E26 Log into CTC task on page 16 39 to log into an ONS 15600 on the network Step2 Click the Alarms tab a Verify that the alarm filter is not turned on See the DLP E157 Disable Alarm Filtering task on page 17 50 as necessary b Verify that no unexplained conditions appear on the network If unexplained conditions appear resolve them before continuing Refer to the Cisco ONS 15600 SONET Troubleshooting Guide c Complete the DLP E76 Export CTC Data task on page 16 98 to export alarm and condition information Step3 In node view double click the ASAP card where you want to provision the line rate Step4 Click the Provisioning gt Pluggable Port Modules tabs Step5 In the Pluggable Ports pane click Create The Create Port dialog box appears Step6 In the Create Port dialog box complete the following e Port Click the PPM number and port number from the drop down list The first number indicates the PPM and the second number indicates the port number on the PPM For example the first PPM with one port displays as 1 1 and the second PPM with one port displays as 2 1 When a 4PIO is present on an ASAP card the port is identified as 4PIO PPM Port for example 4 4 1 The 4PIO number can be 1 to 4 the PPM number can be to 4 but the port number is alway
11. ioning gt Pluggable Port Modules tabs In the Pluggable Port Modules pane click Create The Create PPM dialog box appears In the Create PPM dialog box complete the following e PPM Click the slot number where the SFP is installed from the drop down list e PPM Type Click the number of ports supported by your SFP from the drop down list If only one port is supported PPM 1 port is the only menu option Click OK The newly created port appears on the Pluggable Port Modules pane The row on the Pluggable Port Modules pane turns light blue and the Actual Equipment Type column lists the equipment name Verify that the PPM appears in the list on the Pluggable Port Modules pane If it does not repeat Steps 5 through 8 Repeat the task to provision a second PPM Click OK Continue with the NTP E151 Provision an Optical Line Rate procedure on page 11 3 to provision the line rate Stop You have completed this procedure Cisco ONS 15600 Procedure Guide R5 0 Pit E February 2008 l Chapter 11 Change Card Settings NTP E151 Provision an Optical Line Rate W NTP E151 Provision an Optical Line Rate Purpose This procedure provisions the line rate on a multirate pluggable port module PPM Single rate small form factor pluggables SFPs or 4 port I O modules 4PIOs do not need line rate provisioning Tools Equipment None Prerequisite Procedures NTP E148 Preprovision an SFP Slot page 2 8 or NTP E157 Provis
12. m Filtering task on page 17 50 as necessary b Verify that no unexplained conditions appear on the network If unexplained conditions appear resolve them before continuing Refer to the Cisco ONS 15600 SONET Troubleshooting Guide c Complete the DLP E76 Export CTC Data task on page 16 98 to export alarm and condition information Step3 You cannot delete a port on a PPM if it is in service part of a protection group has a communications channel termination in use is used as a timing source has circuits or has overhead circuits As needed complete the following procedures and task e NTP E61 Modify or Delete Optical 1 1 Port Protection Settings page 10 4 e NTP E62 Change Node Timing page 10 4 e NTP E128 Modify or Delete Communications Channel Terminations and Provisionable Patchcords page 10 7 e NTP E52 Modify and Delete Circuits page 9 2 e NTP E134 Modify and Delete Overhead Circuits page 9 3 e DLP E115 Change the Service State for a Port page 17 14 Step4 In node view double click the ASAP card where you want to delete PPM settings Step5 Click the Provisioning gt Pluggable Port Modules tabs Step6 To delete a PPM and the associated ports a Click the PPM line that appears in the Pluggable Port Modules pane The highlight changes to dark blue b Click Delete The Delete PPM dialog box appears c Click Yes The PPM provisioning is removed from the Pluggable Port Modules pane and the Pluggable Ports pane Ste
13. nge an optical port from SONET to SDH NTP E125 Change Card Service State page 11 13 As needed complete this procedure to change card service state I February 2008 Cisco ONS 15600 Procedure Guide R5 0 E Chapter11 Change Card Settings HE ONTP E157 Provision a Multirate PPM NTP E157 Provision a Multirate PPM Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step7 Step 8 Step 9 Step 10 Step 11 Purpose This procedure provisions a multirate pluggable port modules PPMs in CTC Tools Equipment None Prerequisite Procedures NTP E147 Install the ASAP Card page 2 5 DLP E211 Install the ASAP 4PIO Modules page 18 12 as needed DLP E215 Install an SFP page 18 14 as needed Required As Needed Required Onsite Remote Onsite or remote Security Level Provisioning or higher Complete the DLP E26 Log into CTC task on page 16 39 to log into an ONS 15600 on the network Click the Alarms tab a Verify that the alarm filter is not turned on See the DLP E157 Disable Alarm Filtering task on page 17 50 as necessary b Verify that no unexplained conditions appear on the network If unexplained conditions appear resolve them before continuing Refer to the Cisco ONS 15600 SONET Troubleshooting Guide c Complete the DLP E76 Export CTC Data task on page 16 98 to export alarm and condition information In node view double click the ASAP card where you want to provision PPM settings Click the Provis
14. p7 Verify that the PPM provisioning is deleted e Ifthe PPM was pre provisioned CTC shows an empty slot in CTC after it is deleted e Ifthe SFP or 4PIO is physically present when you delete the PPM provisioning CTC transitions to the deleted state the ports if any are deleted and the PPM is represented as a gray graphic in CTC The SFP or 4PIO can be provisioned again in CTC or the equipment can be removed in which case the removal causes the graphic to disappear I February 2008 Cisco ONS 15600 Procedure Guide R5 0 E Chapter11 Change Card Settings HI NTP E66 Modify Line and Status Thresholds for Optical Ports amp Note If you need to remove the SFP see the DLP E216 Remove an SFP procedure on page 18 15 If you need to remove the 4PIO see the DLP E217 Remove a 4PIO Module procedure on page 18 16 Stop You have completed this procedure NTP E66 Modify Line and Status Thresholds for Optical Ports Purpose This procedure changes line settings line type coding and length line status in service or out of service and performance monitoring thresholds for OC 48 OC 192 cards and OC N ports on ASAP cards Tools Equipment None Prerequisite Procedures NTP E157 Provision a Multirate PPM page 11 2 Required As Needed As needed Onsite Remote Onsite or remote Security Provisioning or higher Step 1 Complete the DLP E26 Log into CTC task on page 16 39 at the node where you want to change th
15. ption Options FC Failure count Numeric Defaults 15 min 1 day Line e 10 40 OC 48 OC 192 Near and Far End Path e 10 10 OC 48 OC 192 Near and Far End UAS Unavailable seconds Numeric Defaults 15 min 1 day Line e 3 10 OC 48 OC 192 Near and Far End Path e 10 10 Near and Far End PSC Protection Switching Count Line Numeric Defaults 15 min 1 day Line e 1 5 Near End e 0 0 Far End PSD Protection Switch Duration Line Numeric Defaults 15 min 1 day Line e 300 600 Near End e 0 0 OC 48 OC 192 Far End PSC W Protection Switching Count Working Line Numeric Defaults 15 min 1 day Line e 1 5 Near End PSD W Protection Switch Duration Working Line Numeric Defaults 15 min 1 day Line e 300 600 Near End Step9 As needed complete the following a Click Physical to provision the physical options in Table 11 4 for each OC N port b Change the selection to 15 Min or 1 Day as necessary c Click Refresh to view or modify the thresholds for each selection Cisco ONS 15600 Procedure Guide R5 0 I February 2008 EN Chapter11 Change Card Settings HI NTP E105 Change an Optical Port to SDH Step 10 NTP E105 Change an Optical Port to SDH Step 1 Step 2 Step 3 Step 4 Step 5 Table 11 4 OC N Threshold Options Physical Heading Description Options Port Port number 1
16. r on the network If unexplained conditions appear resolve them before continuing Refer to the Cisco ONS 15600 SONET Troubleshooting Guide c Complete the DLP E76 Export CTC Data task on page 16 98 to export alarm and condition information Step3 In node view double click the ASAP card where you want to edit the PPM port rate Step4 Click the Provisioning gt Pluggable Port Modules tabs Step5 Click the port with the port rate you want to change in the Pluggable Ports pane The highlight changes to dark blue Step6 Click Edit The Edit Port Rate dialog box appears Step7 In the Change To field use the drop down menu to select the new port rate and click OK Step8 Click Yes on the Confirm Port Rate Change dialog box Stop You have completed this procedure Cisco ONS 15600 Procedure Guide R5 0 Pais February 2008 l Chapter 11 Change Card Settings NTP E149 Delete Pluggable Port Modules W NTP E149 Delete Pluggable Port Modules Purpose This procedure deletes PPM provisioning for SFPs on the ASAP card Tools Equipment None Prerequisite Procedures NTP E157 Provision a Multirate PPM page 11 2 Required As Needed As needed Onsite Remote Onsite or remote Security Level Provisioning or higher Step 1 Complete the DLP E26 Log into CTC task on page 16 39 to log into an ONS 15600 on the network Step2 Click the Alarms tab a Verify that the alarm filter is not turned on See the DLP E157 Disable Alar
17. s 1 e Port Type Click the type of port from the drop down list The port type menu displays the supported port rates on your PPM See Table 11 1 for definitions of the supported rates on the ASAP card Step7 Click OK Step8 Repeat Steps 5 through 7 to configure the port rates as needed Table 11 1 PPM Port Types Card Port Type ASAP e OC 3 155 Mbps e OC 12 622 Mbps e OC 48 2 48 Gbps e ETHER 10 Gbps Ethernet Cisco ONS 15600 Procedure Guide R5 0 I February 2008 EEN Chapter11 Change Card Settings HI NTP E150 Change the Optical Line Rate Step9 Click OK The row on the Pluggable Ports pane turns light blue until the actual SFP is installed and then the row turns white Stop You have completed this procedure NTP E150 Change the Optical Line Rate Purpose This procedure changes PPM port rates for the ASAP card Perform this procedure if you want to change the port rate on a multi rate SFP that is already provisioned Tools Equipment None Prerequisite Procedures NTP E157 Provision a Multirate PPM page 11 2 Required As Needed As needed Onsite Remote Onsite or remote Security Level Provisioning or higher Step 1 Complete the DLP E26 Log into CTC task on page 16 39 to log into an ONS 15600 on the network Step2 Click the Alarms tab a Verify that the alarm filter is not turned on See the DLP E157 Disable Alarm Filtering task on page 17 50 as necessary b Verify that no unexplained conditions appea
18. ws a 11 Change Card Settings This chapter explains how to change transmission settings on cards in a Cisco ONS 15600 Before You Begin As necessary complete the NTP E57 Document Existing Provisioning procedure on page 7 2 Before performing the following procedures investigate all alarms and clear any trouble conditions Refer to the Cisco ONS 15600 Troubleshooting Guide as necessary This section lists the chapter procedures NTPs Turn to a procedure for applicable tasks DLPs 1 NTP E157 Provision a Multirate PPM page 1 1 2 Complete this procedure to provision a multirate pluggable port module PPM for the ASAP card If a multirate PPM was preprovisioned this procedure is unnecessary NTP E151 Provision an Optical Line Rate page 11 3 Complete this procedure to provision the optical line rate on a multirate PPM for the ASAP card Single rate PPMs do not need to be provisioned NTP E150 Change the Optical Line Rate page 11 4 As needed complete this procedure to edit optical line rates for multirate PPMs on the ASAP card NTP E149 Delete Pluggable Port Modules page 11 5 As needed complete this procedure to delete PPMs for the ASAP card NTP E66 Modify Line and Status Thresholds for Optical Ports page 11 6 As needed complete this procedure to change line drop and threshold settings for all OC N cards NTP E105 Change an Optical Port to SDH page 11 12 As needed complete this procedure to cha
Download Pdf Manuals
Related Search