Chief Manufacturing MSS6000 User's Manual
Contents
1. 6 May remove up pin and nut and 1 move to lower holes Q A padlock or bolt may be placed through latch holes Figure 6 Removing Display from Mount 1 Remove bolt or padlock from faceplate if used See Figure 7 NOTE The pin may have been used as a more permanent locking device If so remove nut and pin and move from the lower holes to the upper holes 2 Pull back on flag on upper mounting hole and press pin down into Open position See Figure 7 3 Carefully lift display from mount 4 Liftupon pin and place flag back against faceplate to return it to Closed position See Figure 7 Installation Instructions MSS6000 Height Adjustment Screws 2 each side Remove bolt or padlock ap if used o 5 Max Pin in Closed position move to Open position to remove display Figure 8 Display Roll Adjustment The MSS 6000 provides limited display roll adjustment Pin in for the purpose of leveling the display Open position To level the display Mea to 1 Loosen upper and lower roll adjustment nuts Closed See Figure 9 position after display 2 Level display See Figure 9 ki Pa 3 Tighten roll adjustment nuts Figure 7 ADJUSTMENTS Displav Height Adjustment CAUTION Displavs are fragile Allowing the displav to drop to bottom of stand mav2. INSTALLATION INSTRUCTIONS LCD Swivel Stand G amp G CHIEF MSS6000 MSS6000 Installation Instructions DISCLAIMER Milestone AV Technologies Inc and its affiliated corporations and subsidiaries collectivelv Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for everv possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions DIMENSIONS WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty Itis the installer s responsibility to make sure all components are properly assembled and installed using the instructio
3. fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche By Hand A mano Von Hand Com a m o A mano Met de hand la main p y bi 3 Hex Head Wrench Llave de cabeza hexagonal O CG Sechskantschl ssel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Pencil Mark Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez Optional Opcional Optional Opci
4. isplavs 24 in height or less If a display with a height greater than 24 is being installed follow the instructions below To install a display with a height greater than 24 1 Remove slide plate assembly from the base by removing four 5 16 18 x 3 4 button head cap screws and four 1 4 flat washers See Figure 3 Q O 9 D Slide Plate Assembly Figure 3 2 Remove face plate from slide plate assembly by removing two 3 8 16 x 1 round head carriage bolts two 1 OD x 563 ID spacers two 3 8 flat washers and two 3 8 16 lock nuts See Figure 5 3 Reinstall face plate into upper mounting holes of slide plate using two 3 8 16 x 1 round head carriage bolts two 1 OD x 563 ID spacers two 3 8 flat washers and two 3 8 16 lock nuts removed in Step 2 See Figure 5 4 Reinstallslideplateassembly ontobase usingfour 5 16 18 x 3 4 button head cap screws and four 1 4 flat washers previously removed in Step1 See Figure 3 5 Raise slide plate assembly to maximum height 6 Secure slide plate in place by tightening the four height adjustment screws See Figure 2 Slide Plate Face Plate 9 AY Lock Nut L Flat Washer Spacer cius Bolt Figure 4 MSS6000 Installation Instructions Displav Installation The following procedure assumes that the proper interface bracket for the displa
5. n routes the cables across the mounting surface and out the rear cable access slot in the back of the mount See Figure 13 TU INTA e S S FS 22 9 2602 7 e PIO AA NU X Cable Access Figure 13 Option C Option C uses the cable access at the center of the MSS 6000 and then routes the cables down through an access Figure 14 MSS6000 Installation Instructions CHIEF 8800 000057 Rev B 2008 Chief Manufacturing www chiefmfg com 03 08 USA International Europe Asia Pacific A P F A P F A Nati JIR P F 8401 Eagle Creek Parkwav Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA JJI me 2 iX BARA BAB DEK24F 86 755 8996 9226 86 755 8996 9217
6. ns provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located on the MSS including the display does not exceed 150 Ibs 68 04 kg TOP MOUNTING BUTION ON MSB XXXX DRAWING GOES HERE NOTE CUSTOM INTERFACE BRAC KET NOTSHOWN THE CUSTOM INTERFACE BRAC KET NEEDED FOR YOUR DISPLAY WILL ADD BETWEEN 1 2 AND 2 IN DEPTH AND MAY AFFECT LOCATION OF DISPLAY ON THE MOUNT SEE MSB XXXX DRAWING ALSO 2 53 5 07 _ __ 1 i ge 24 50 MAX o Q 19 25 MIN Lon Cc APPRO XIMATE j CENTER OF DISPLAY B 3301 929 I 14 25 Installation Instructions MSS6000 LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il
7. onal Opzionale Optie En option Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguranca Chiave di sicurezza Veiligheidssleutel Cl de s curit MSS6000 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 5 32 3 16 3 8 Provided Provided B 5 C 1 D 1 5x 5x 203 5 32 3 16 Installation Instructions MSS6000 INSTALLATION Mount Installation Free Standing not anchored Applications Only NOTE Do not perform this step if you are going to anchor the stand to a surface 1 Install five rubber bumpers B on bottom of stand See Figure 1 a Rubber Bumpers 5 places View from Bottom Figure 1 Display 24 Inches High or Smaller 1 Loosen the four height adjustment screws and raise the slide to its maximum height See Figure 2 2 Secure the slide by tightening the four height adjustment screws Faceplate Height Adjustment Screws 4 jq x 4 Lh RE l IT Ili Figure 2 Displav More Than 24 Inches High NOTE The MSS 6000 comes pre configured for d
8. owing the instruction outlined in Display Installation section on page 6 7 Test display swivel tension by grasping each side of display and turning display left and right If additional swivel tension adjustment is required repeat 8 steps 1 through 7 above Display Swivel Stop Location Adjustment The MSS 6000 allows for the installation of swivel stops that limit the amount of display travel Stops can be installed at 15 25 or 35 degrees To install swivel stops 1 Follow steps 1 through 3 of Display Swivel Tension Adjustment section 2 Insertone 10 24 X 1 2 Phillips head cap screw in one of the three swivel stop holes 15 25 or 35 degrees in the base of the stand See Figure 11 n D IL 2 lt e c e Tension Adjustment Screw Turn left to decrease tension urn right to increase tension O Figure 11 Installation Instructions MSS6000 Cable Management The MSS 6000 has been designed to provide multiple cable management routing options Option A Option A does not use the cable access features of the MSS 600 and simply routes the cables away from the display and mount See Figure 12 Option B Option B uses the cable access at the center of the MSS 6000 and the
9. result in damage to the displav 1 While holding the display loosen the four height adjustment screws See Figure 8 CAUTION Make sure all cables and wires are not pinched when raising or lowering display 2 Position display at the desired height 3 Tighten four height adjustment screws See Figure 8 MSS6000 Installation Instructions Roll Adjustment Nuts 2 places O inu TIT ITI NOTE Adjustment nuts located between slide plate and back plate of base assembiv Figure 9 Displav Swivel Tension Adjustment Displav swivel tension is pre set at the factorv Swivel tension will varv depending on the weight of displav being mounted If swivel tension adjustment is required 1 Disconnect all cords and cables from display 2 Follow steps in Removing Display from Mount section 3 Lay mount on back See Figure 10 4 Locate three tensions adjustment screws See Figure 10 5 Turn each adjustment screw either clockwise to increase tension or counter clockwise to decrease tension NOTE It is important that all adjustment screws are turned equal amounts in the same direction for the display to turn properly 6 Install display foll
10. v being mounted has alreadv been installed on the displav If no interface bracket is present on display install bracket to display using the instructions included with the interface bracket before proceeding If an interface bracket for the display being mounted needs to be obtained or additional assistance is required contact a Chief Customer Service representative by calling 1 800 582 6480 or by visiting www chiefmfg com NOTE If the display being mounted has a height of more than 24 the mount needs to be modified prior to display installation See Display More Than 24 Inches High on page 5 To install the display 1 While supporting both sides of display align four mounting buttons on display or interface bracket with four mounting holes in faceplate See Figures 5 and 6 Figure 5 2 Lower display into place listening for audible click to ensure recessed area of mounting buttons are properly seated in lower area of mounting holes See Figures 5 amp 6 WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Ensure mounting buttons are completely engaged in mounting holes NOTE Holes are provided in the faceplate for use with a padlock or similar locking device if desired In addition the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure
Download Pdf Manuals
Related Search