Casablanca Fan Company Inteli-Touch 3 PN User's Manual
Contents
1. 8 Install the W 85 in the wall box with the two long screws provided POWER SOURCE 9 Install the wall plate with the two short color matched screws provided 120V AC BLACK AND WHITE STRIPED WIRE 10 Installation of the second W 85 control is identical Repeat steps 1 through 9 FIGURE 5 ooo Inteli Touch 3 OPERATION POWER The POWER button is normally left in the on position Always turn the power off during cleaning or servicing the fan and during thunderstorms It is also used to exit or enter ad E rower ditional programs The POWER button must be left on to retain a previously set fan speed or light level OPERATION SPEED CONTROL There are six individual speed settings for the fan each speed is indicated by an audible tone of increasing pitch FAN CONTROL To select the desired fan speed 1 With fan off press and hold the button labeled FAN D The fan blades will start rotating ON OFF at the slowest speed and will increase in steps 2 Release the button when the desired speed is reached A momentary press of the FAN The fan speed is now in memory and will automatically come on at the same PURON speed each time the FAN D button is used To maintain this level of speed turn CHANGE SPEED the fan on by pressing less than one second To lower speed turn fan d hold i off then on by pressing and holding the button until the desired speed ioe ANG TO is reached When the fan2. Fan Size Variable fan speed capability permits the use of a full size 52 fan even in smaller J rooms For very large rooms two fans may be needed Suggested Extension Pole Lengths Ceiling Height Pole Length Standard Standard 6 12 12 18 24 36 48 When to Use Extension Poles For best performance and best appearance an extension pole should be used with your Casa blanca fan when installing on high cathedral ceilings or sloped ceilings Casablanca offers standard poles in increments of 6 up to 5 Custom poles are available in lengths up to 9 9 See your Authorized Casablanca Dealer for details Note Fan may wobble or vibrate if pole length is not long enough and inside blade is too close to downslope or side wall Extending pole length will usually solve problem Calculation of 32 MAXIMUM HANG TRU EXTENSION ANGLE 32 POLE pu did BLADES MUST BEA MINIMUM OF 7 ABOVE THE FLOOR 7 MINIMUM EXAMPLE 1 This slope is less than 32 dl It is OK to install your fan EXAMPLE 2 This slope is 32 This is the maximum gl slope that will allow the fan to hang straight down It is OK to install your fan Use the tear off Ceiling Angle Template card inserted in the EXAMPLE 3 3 This slope is more than 32 back of this manual it provides you with a simple
3. ay INSTALLING THE HALOGEN BULB Step 13 Screw the 100 Watt Halogen bulb into the socket Do not touch the glass bulb with your fingers it is extremely important that the glass be clean If it is touched or dirty clean carefully with a tissue A dirty glass bulb will cause the bulb to fail almost immediately IMPORTANT When installing the halogen bulb carefully cut off the end of the plastic sleeve the bulb comes in and hold the bulb by the plastic sleeve to screw it into the socket HALOGEN BULB 100 WATT INSTALLING THE GLASS SHADE Step 14 Position the indentations in the outer rim of the glass shade so that they line up with the tabs on the inside surface of the fan light fixture rim LIGHT FIXTURE Step 15 Carefully lift the glass shade up inside the light fixture as far as it will go Step l6 Rotate the shade in a clockwise direction until it is held tightly in place by the three tabs TIP At first the shade is a very loose fit in the fixture and can be wiggled a little from side to side It is a great help when rotating the glass shade to wiggle it at the same time In compliance with U S federal energy regulations T GLASS this ceiling fan contains a device that restricts the light SHADE fixture to a maximum of 190 watts WARNING Exceeding that limit or the marked limit on this product may result in fire hazard or improper operation Inteli Touch 3 W 85 CON
4. COSA CROSSBAR MOUNTIING BRACKET INSTALLATION Proceed with installation as follows Step 1 Route the wires from the ceiling outlet box through the crossbar mounting bracket center hole Attach the bracket with ground wire and ridges down to the ceiling fixture outlet box with the mounting hardware included with the outlet box Tighten the screws firmly by hand only being careful not to bend the bracket by over tightening CAUTION To reduce the risk of personal injury use only the mounting hardware provided with the approved outlet box to install the crossbar mount ing bracket CEILING FAN APPROVED OUTLET BOX CEILING WIRING CROSSBAR MOUNTING BRACKET FLAT ff WASHER Cf OUTLET BOX MOUNTING HARDWARE X ane J NC Ss D f Ss NN CN g i i CANOPY CANOPY HATCH GLASS SHADE 00 CANOPY SCREW 4 4 O CANOPY LOCK WASHER 4 n HALOGEN BULB 100 WATT BODY TOP COVER CANOPY INSTALLATION Step 2 Attach the canopy to the crossbar mount ing bracket with three of the 8 32 x 2 long canopy screws and canopy lock washers Tighten the screw firmly by hand only Note On sloped ceilings align the canopy opening towards the top or room peak CROSSBAR MOUNT ING BRACKET INSTALLED CANOPY BEL AIR Yo INSTALLING THE FAN BODY TOP COVER IMPORTANT To avoid possible damage to the Halogen bulb holder the fan m
5. by twisting the bare ends of the wires together and then securing with a BLACK wire nut WIRES Connect in this order e GREEN leads from mounting plate and fan to GROUND conductor of WHITE WIRES power source Secure with wire 2 nut e WHITE wire from fan to white NEU TRAL wire in ceiling fixture outlet box Secure with wire nut e BLACK wire from fan to black or red POWER wire in ceiling fixture outlet box Secure with wire nut GREEN WIRES 3 WIRE NUT s CANOPY HATCH INSTALLATION Step 9 Tuck the wires into the canopy with the wire nuts pointed upwards so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy CANOPY opening HATCH CANOPY Step 10 Install canopy hatch with the WASHER last canopy screw and lock washer To do this tilt the fan body away from the hatch opening CANOP SCREW Step 11 Straighten the fan then TILT THE check to ensure that there is no FAN TO movement between the canopy and ASTU ceiling or Hang Tru ball and top sup CANOPY port shaft SCREW BEL AIR Yo BLADE HOLDER HARDWARE mm BLADE SCREW 4 FLAT WASHER PER BLADE 4 PER BLADE CENTER STYLE BLADE HOLDER amp BLADE BLADE SCREW 4 PER BLADE Step 12 Blade Installation Attach the blades to the blade holders with four blade screws and four steel washers provided for each blade Hand tighten securely FLAT WASHER 4 PER BLADE
6. go or oues Your fan will not hang straight down no go for installing your fan on a sloped ceiling an adaptor is necessary Contact your local Authorized Casablanca Dealer in regards to purchasing a Slope Ceiling Adaptor BEL AIR Yeo Unpacking Before assembling and installing your ceiling fan remove all parts from the shipping cartons and check them against the parts listed here Before discarding packaging material be certain that all parts have been removed IMPORTANT To avoid possible damage to the Halogen bulb holder the fan must be placed on the styrofoam packaging from the box After removing the top cover from the upper half of the styrofoam take the packaging from the box and put it on the floor Place the fan in the recessed circle that the top cover was in WM ALLEN SET S REN DOWNROD amp BALL wiih 4 20 x 1 4 1 8 ASSEMBLY PRE INSTALLED ALLEN WRENCH IMPORTANT SAFETY INFORMATION y BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN MOTOR INSTALL THE THREADED DOWNROD INTO THE WIRES MOTOR COUPLING AND LOCK THE ASSEMBLY GROUND Prepare for fan installation as follows WIRE Step A Route the wires from the motor through the PermaeLock downrod and ball assembly DOWNROD amp BALL Tip The downrod has a tapered thread ASSEMBLY that is designed to lock completely when correctly installed TAPERED Step B Using the provided allen wrench loosen the set screw Dind U
7. is on you may increase the speed by pressing and FAN button longer holding the button until the desired speed is reached then release it than one second OPERATION REVERSING AIRFLOW The direction of airflow can be changed from downward to upward or from upward to downward To reverse the airflow Note A four toned signal indicates the command was accepted by the fan A few dn sure the is on and blades are Turn Saeondelateriba A to a stop and then reverse Cm urn 2 Press the REVERSE button EET OPERATION LIGHTS To turn the lights off and on press and release the button for less than one second 1 First press release of the button The light will turn ON 2 Second press release of the button The light will turn OFF To vary the light brightness at each touch level LIGHT CONTROL To vary the light brightness Y J J ON OFF A momentary press of 1 With lights off press and hold the button After one second the lights will the LIGHT button come on at their lowest level and gradually become brighter CHANGE BRIGHT 2 Release the button when the desired brightness level is reached NESS PRESS AND HOLD NOTE Light Operation the light varies from bright to dim over LIGHT BUTTON approximately 8 seconds This sequence will reverse the light when it reaches LONGER THAN ONE the brightest or dimmest level if you continue to hold the LIGHT button SECOND Release the button
8. when the desired level is reached The brightness level is now in the fan memory and will automatically come on at the same brightness the next time the button is used ee 3 CHANGING FREQUENCY SETTING E Inteli Touch 8 NOTE All fans leave the factory set to DIP 1111 SWITCHES You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately Step 1 Turn power OFF at the circuit breaker or fuse box and at the toggle switch for the fan you want to change NOTE DO NOT set dip switch setting in the remote to 0000 this may cause frequency interference from other Casablanca Products Step 2 Remove the screws and switch plate from the existing switch box Step 3 Remove the screws holding the switch in the switch box Step 4 Pull the existing W 85 switch from the switch box to expose the dip switches located on the side of the control as shown in Figure 1 DIP SWITCHES DIP SWITCHES SET TO 1111 SET TO 1001 Step 5 Change the dip switch settings assuring that they are different from the Factory Setting previously installed Inteli Touch 3 fan Step 6 Mount the W 85 Wall Control unit back into the wall electrical box Step 7 At the circuit breaker or fuse box and at the toggle switch turn the power off for the fan whose frequency you are changing Th FAN _ ae ROR Step
9. 8 Within 20 seconds of restoring power to the ceiling fan and the W 85 Wall Control press and hold both the FAN and REVERSE buttons as shown in Figure i 2 for 3 seconds you will hear one tone from the Piezo Buzzer indicating the com mand has been accepted AUTOMATIC DEMONSTRATION PROGRAM Lights slowly increase to full intensity Fan accelerates to speed three with audio tones Light dims to half intensity Fan accelerates to full soeed with audio tones Fan reverses at full soeed with audio tones Fan operates at full speed Fan turns off with audio tones blades coast for a short time Lights turn off Programmed into every Inteli Touch 3 Series fan is an Automatic Demonstration Program It can be used to fully demonstrate and test the operation of the fan To enter the demonstration program 1 Turn off for at least 5 seconds This will clear the fan memory ready for programming 2 Turn JWE on 3 Immediately operate the buttons in the following sequence The complete cycle lasts slightly over one minute It will continue to repeat until the is turned off for more than five seconds cancelling the program A multi tone signal will verify the start of the test program which proceeds as follows o Inteli Touch 3 NOTE Both Light Minder and Safe Exit programs will always run at the same time The Safe Exit Program gives you about thirty seconds of light when you tur
10. CONTENTS INTRODUCTION MET 1 MOUNTING RECOMMENDATIONS e eee me enne hene rrr nnn 2 FAN ANS TAELATION erties EA Et UN E A A A MUNI LED EIUS UCM EM 3 CONTROL FEATURES INTEEISTOUCTELS OPERATION einen ene et ee ee ee ee etse Un tueri ee eee 8 INTELII TOUCH 3 TROUBLESHOOTING eect eee etter nennen 16 READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation therefore before attempting to install and operate your Casablanca fan read this owner s manual completely and carefully Retain this manual for future reference CAUTION To avoid possible electrical shock make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation procedure CAUTION RISK OF ELECTRICAL SHOCK All wiring must be performed in accordance with national and local electrical codes If you are unfamiliar with the wiring codes you should use a qualified electrician To avoid overheating and possible damage to other equipment do not install control to a receptacle fluorescent light fixture motor operated appliance or transformer supplied appli ance This fan is designed to be installed on an existing electrical outlet box The outlet box must be UL Listed for ceiling fan installations if it is not a new box must be installed Casabl
11. N several turns to allow installation of the downrod Thread the downrod into the motor coupling until it stops turning this REN will take at least four and a half full turns SET SCREW uu Step C Securely tighten the set screw with the provided allen lin wrench to ensure safe operation of your fan MOTOR F COUPLING CAUTION Failure to fully lock in the downrod 4 before securely tightening the set screw may cause the fan to separate from the downrod 9 during normal operation N ADDITIONAL HARDWARE Amer EN E a es 4 __ 4 00 21 4 x 8 32 ROUNDED lt 7 SROSSHAR HEAD SCREW 2 e ee WIRE NUT 4 mumy 1 x 8 32 ROUNDED FLAT BRACKET HEAD SCREW 2 WASHER 2 j Installing a New Ceiling Fixture Outlet Box Using Existing Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish After turning the power OFF at its source either circuit to place your Casablanca fan an approved ceiling fixture outlet breaker or fuse box lower the old fixture and disconnect box must be installed and wired the wiring Check the ceiling fixture outlet box to be sure Warning To reduce the risk of fire electrical shock or that it is marked Approved for ceiling fan mounting If it is personal injury mount to outlet box marked acceptable for not a new box must be installed ceiling fan support using the mounting hardware provided with the outlet box
12. ON Ensure power is turned OFF at the breaker or fuse panel before starting installation FIGURE 4 WHITE ereen et Tocontrol the fan and lights from two locations a three way circuit use two W 85 wall controls 1 Remove the screws and switch plate from the existing switch box and the BLACK WITH screws holding the switch in the switch box GREEN peas GREEN p W 85 W 85 2 Pull the existing switch from the switch box to expose the wire connections xm cum RED BLACK WITH WHITE STRIPE BLACK 3 Determine which wire is connected to the common terminal from the power iai RE source 120V AC of the three way switch The terminal will be marked BLACK RED on switch BLACK BLACK BLACK 4 Remove the wire from the common terminal of the three way switch Connect this W 85 wire to the remaining black white striped wire on the W 85 control Secure this splice 2 BLACK Wall Control with a wire nut WIRES 5 Remove the two remaining wires from the three way switch Connect the black wire of these wires to a black wire on the W 85 control Secure the splice with a wire nut The remaining red wire is to be connected to the other red wire on the W 85 Secure the splice with a wire nut 6 Connect the green ground wire coming from the back of the W 85 control to the ground wire in the switch box Secure the splice with a wire nut 7 Check your work by using the wiring diagrams as shown in Figure 5 on this page
13. Safe Exit command has been accepted The lights will stay on for 30 seconds and then begin to dim After thirty seconds have elapsed the lights will turn completely off 4 To cancel the Light Minder and Safe Exit Programs press the ower button The Home Safe Program makes an unoccupied home appear occupied by turning the lights on and off at random times To enter the Home Safe Program 1 To operate the lights and fan for Home Safe Program Press the POWERS Button off for a least 5 seconds 2 Turn the oweRD on Immediately press the buttons in the following sequence GCEIGHT GLIGHT CEIGHT CEEANCO A series of tones will be heard through the piezo buzzer and flashing lights indicating the command has been accepted will follow This program overrides all manual control of lights and fan Once the lights turn on they will automatically turn off after 2 hours 3 The lights will automatically cycle on and off in a controlled sequence as follows ON 1 hour OFF 75 hour ON 2 hours OFF 1 hour ON 7 hour then OFF 2 hours This seven hour pattern will repeat continuously so that a different pattern of lighting is seen each day of the week 4 To cancel the Home Safe Program press the POWER Button OFF for five seconds Safe Exit Light Minder Inteli Touch 3 OPERATION FAN MINDER PROGRAM The Fan Minder feature will add to your comfort when used in the bedroom The program reduces the speed of the f
14. TROL INSTALLATION WALL CONTROL AND HARDWARE not to scale aa W 85 Switch Mounting Switch Bezels Wall Plate 4 Wire Cap i Screws Wall Control Screws 2 1 White White Wall Almond Wall 2 Plate 1 Plate 1 2 White 1 Almond 2 Almond WARNING To avoid possible electrical shock make cer tain that electricity is turned off at the circuit breaker or fuse box before attempting any in stallation or repair procedure CAUTION NOT turning the power OFF at the circuit breaker or fuse box may cause damage to the electronics within the wall control and or the PC board on the fan Before installing the W 85 wall control you will need to check and see if you will need to change the bezel on the front of the wall control from WHITE to ALMOND If you are going to use white skip these steps and go to wall control installation starting on page 1 The bezel can be changed at any time before or after installation The wall control does not need to be uninstalled to replace the bezel W 85 Wall Control Bezel Replacement installation as follows Step 17a Locate the four 4 tabs holding the bezel to the front of the switch then press in on each tab one at a time removing the bezel as shown in Figure 1 LOCATING PINS HOLES 4 RUBBER KEY PAD Step 17b Locate the rubber key pad attached to the four 4 locating pins as shown in Figure 2 and remove rubber key pad from t
15. an each two hour interval to compensate for cooling night air To enter the Fan Minder Program 1 Turn the OFF for at least 5 seconds 2 Turn the ON 3 Immediately operate the buttons in the following sequence C LIGHT C LIGHT FC FAN o FAN 4 The fan will respond with three descending tones A timer is now initiated and the fan will reduce one speed for each two hour interval The fan will not however descend below the second lowest speed 5 You may increase the fan speed by pressing and holding the button until the desired speed is reached then release it The fan will again reduce one speed for each 2 hour interval 5 To cancel the Fan Minder Program turn the OFF for three seconds TROUBLESHOOTING TIP Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance Inteli Touch 3 PROBLEM POSSIBLE REMEDIES Fan will not start e Check the main circuit fuses circuit breakers and wall switch position Check all wire connections Make sure the power is turned off during this inspection e Pin connectors are not making good contact Check all connections e The fan receiver is defective Replace the fan receiver e Reset the frequency setting Turn the power off at the circuit breaker for the fan that is not functioning only Within 20 seconds from restoring power to the ceiling fan and the W 85 Wall Control press and hold both the Fan and REVERSE
16. anca extension poles are available for sloped or high ceiling installations e This ceiling fan requires a grounded electrical supply of 120 VAC 60 Hz and a minimum 15 amp circuit The maximum current require ment for the fan with light fixture is 3 8 amps The fan uses about amp or 100 watts Maximum light current is 1 0 amps or 100 watts of lighting e Where wire nuts are employed be sure all bare wires are within the connectors When installing the canopy hatch make sure all wires are within the canopy and that no wires are being pinched For best performance and for your warranty to be valid use only genuine Casablanca blades light fixtures and accessories The blades in each pack are matched for equal FUSE BOX weight to assure smooth fan operation If more REMOVE FUSE FORTHE than one fan is being installed be careful not to CIRCUIT YOU WILL BE mix blades from different cartons WORKING ON Inspect the contents of your carton for possible shipping or handling damage and report any such J J damage directly to your authorized Casablanca dealer 2 e Itis always a good idea to have an assistant to help LO Oo jt 70 with the installation HD i When cleaning painting or working near your fan WE be very careful of the fan and blades Always turn CIRCUIT BREAKER the power OFF to the ceiling fan before servicing TRIP BREAKER FOR THE 84 it working on it or replacing light bulb
17. ated on the back of the W 85 wall control Secure this connection with a wire nut 7 Connect the green ground wire coming from the back of the W 85 control to the ground wire in the switch box Secure the splice with a wire nut 8 Check your work by using the wiring diagrams as shown in Figures 1 and 2 Xu RED WIRE 9 Install the W 85 in the wall box with the two long NOT USED screws provided 10 Install the wall plate with the two color matched From Screws PO WER SOURCE BLACK AND WHITE 120V AC ECUR TA STRIPED WIRE SEEN LE IL To control the fan and lights from two locations a three way circuit use two W 85 DIP SWITCHES wall controls as shown in the wiring diagram in Figure 5 Before installing the two switches into the wall place both switches side by side then locate the 4 dip switches on the side of the two switches Then make sure that the dip switches are set to the same address on both switches as shown in Figure 4 When setting these dip switches you are setting the channel number that is required to control both your fan and lights from both sides of the room If you are installing other Inteli Touch 3 fans within your home you may need to reset the dip switches on these other fans to a different channel before installing your W 85 wall control into the wall Please review the section on channel changing on this instruction sheet Inteli Touch 3 DUAL W 85 INSTALLATION CAUTI
18. buttons as shown in Figure 2 for 3 seconds you will hear one tone from the Piezo Buzzer indicating the command has been accepted The Fan will come on at low speed in the reverse direction Fan wobbles or shakes excessively Be sure the canopy pin is set properly into the slot on the ball Check that the blade holders have not been bent during installation and the blades are balanced he hanger bracket and or the ceiling outlet are attached too loosely Make sure the hanger bracket is attached tightly to the ceiling outlet box and the downrod assembly is secured firmly he downrod is attached to the downrod base too loosely Make sure all the screws are securely tightened Fan is noisy during operation e When changing fan speeds you may hear several audible clicks This is normal operation Check and tighten the light fixture retaining screws glass shade screws and or lightbulb s Tighten the canopy screws and mounting plate assembly Make sure the wire nuts inside the canopy and switch housing are not touching the metal parts and that they have not fallen off the wire splices Tighten as necessary e Tighten the blade holders to the flywheel or Direct Drive motor and the blades to the bladeholder screws Make sure all the screws in the motor housing are snug but not overly tight Fan does not run on low speed e f fan is new it may need to be broken in Run at high speed for several days This devi
19. ce complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device 1 This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circ
20. he WHITE bezel also as shown in Figure 2 Figure 2 Inteli Touch 3 W 85 Wall Control Bezel replacement CONTINUED ALMOND 7 BEZEL Step 17c Reinstall the rubber key pad on to the four 4 locating pins located on the almond bezel as shown in Figure 3 and 4 RUBBER KEY PAD Figure 3 RUBBER KEY PAD Step 17d To attach the bezel back on to the front of the switch you will need to align the four 4 tabs on the bezel with the front of the wall control and by gently pressing on both top and button of the bezel at the same time snap the bezel back on to the front of the switch as shown in figure 5 LOCATING ALMOND BEZEL PINS 4 Figure 4 ALMOND BEZEL Step 17e Check your work by pressing on the light fan reverse and power buttons making sure that the buttons do not stick and that each switch functions properly BEZEL ALIGNMENT PIN AND HOLE Figure 5 o Inteli Touch 9 3 INSTALLING THE W 85 WALL CONTROL NOTE W 85 Wall Control should only be installed on Casablanca s Inteli Touch 3 fans with DOWNLIGHTS ONLY The wall control installs in the same manner as an ordinary light switch using an existing wall box and wiring This controller is designed to signal the fan microcomputer as well as perform normal switching operations For this reason the following precautions must be observed 1 Use only the Casablanca W 85 wall control 4 No other light fi
21. n the lights off enabling you to exit your home before the lights go out To enter the Safe Exit Program 1 To operate the lights for Safe Exit Program Press the POWER button off for at least five seconds 2 Turn the Power on Immediately press the buttons in the following sequence EAND CEEANCO CEIGHI CEIGHT Immediately press the GEIGHT9 Button after an audio tone is heard from the fan controller The lights will blink to indicate this command has been accepted The lights will stay on for 30 seconds and then begin to dim After thirty seconds have elapsed the lights will turn completely off 3 To cancel the Safe Exit Program press the POWER button off for five seconds NOTE If the lights are left on in the room the lights will automatically turn OFF after 2 hours this is Light Minder The Light Minder Program automatically turns OFF the fan mounted lights after two hours To enter the Light Minder Program 1 To operate the lights for Light Minder Program Press the ower button off for at least 5 seconds 2 Turn the oweRS on Immediately press the buttons in the following sequence GEAND GEAND CHIGHD IGHID A series of tones will be heard through the piezo buzzer indicating the command has been accepted Once the lights turn on they will automatically turn off after 2 hours 3 Light operation still remains normal if you leave the room and turn OFF the lights will blink to indicate this
22. s CIRCUIT YOU WILL BE Never insert anything into the path of the fan blades WORKING ON while the fan is in operation Never install a fan over a pool or spa BS Never operate a fan that has been damaged in any x rx way Contact Casablanca Fan Company by calling XI XE 888 227 2178 or contact your local authorized xz rx Casablanca dealer for assistance in obtaining qu service d PN 384372 HN0909 CASA Before mounting your Casablanca fan read the following helpful recommendations The location of the fan air circulation and fan size are all important factors to consider before installation Location Ceiling fans have practical uses in almost every room in your home We suggest you follow these mounting recom mendations as you decide where to install your Casablanca fan For safety reasons the fan blades must be a minimum of 7 above the floor Do not locate the fan in a doorway or above a swinging door In any installation the tips of the blades must be at least 18 from the wall in order to provide sufficient clearance for the blades In bedrooms fans work best when mounted above the foot of the bed Over pool tables be sure to provide plenty of clearance to avoid damage from pool cues In kitchens be sure to allow for open cupboard doors to clear the fan blades Do not install a fan close to or over a pool or spa High humidity combined with corrosive gases will destroy the finish and warp the blades
23. uit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Note Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one s authority to operate this remote control CASA Model Name Model Number Dimensions PRODUCT SPECIFICATIONS Q9 Co X X Y Ceiling Line c x D gt E k A B C D E N N O o Motor XLP 2000 Blade Span With 55 Blade Pitch 14 No of Blades 5 Technology IntelieTouch Lightbulbs 100 watt halogen 1 Airflow 7 174 cfm Electricity Use 119 watts Airflow Efficiency 60 5 cfm watt
24. ust be placed on the styrofoam packaging from the box After removing the top cover from the upper half of the styrofoam take the packaging from the box and put it on the floor Place the fan in the recessed circle that the top cover was in TOP COVER RETAINING SCREWS Step 3 Locate the three tabs on the top of the fan motor assembly Remove the three top cover retaining screws and set aside for Step 6 Step 4 Locate the top cover and note the three mounting tabs on the top NOTE Make a note of the Fan Serial Number and Model Type before install ing the top cover Step 5 Lower the top cover over the fan downrod with the top cover mounting tabs lined up with the tabs on the fan motor assembly TOP COVER MOUNTING TABS Step 6 Once the tabs are aligned attach the top cover to the motor using the three top cover retaining screws removed in TOP COVER Step 3 Hand tighten ensuring that all screws are engaged RETAINING T SCREWS Test that the cover is on securely before continuing with the installation paN COMPANY 000000 aN HANGING THE FAN Step 7 To hang the fan body in the canopy hold the fan body firmly and insert the ball into the canopy opening Check that no wires were pinched Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening Note Fan weighs 24 lbs Step 8 Attach the fan wires to the ceiling fixture outlet box wiring
25. xtures or electrical appliances may be 2 Do not use any additional control with your Inteli Touch connected on the circuit controlled by the W 85 wall 3 fan for example dimmer or fan speed control control 3 Do not use more than one fan per wall control SINGLE W 85 INSTALLATION CAUTION Ensure power is turned OFF at the breaker or fuse panel before starting installation W 85 is used to describe either white 11 or almond finish DE If you have multiple Inteli Touch 3 fans refer to the section BLACK Changing Frequency Setting on page 13 2 BLACKS 2 WHITES 5 GROUND WIRE NUT 1 Remove the screws and switch plate from the existing switch box 2 Remove the screws holding the switch in the switch box 3 Pull the existing switch from the switch box to expose the wire connections W 85 4 Remove the two wires from the switch 5 Connect the BLACK wire from the POWER SOURCE that you just removed from the switch to the BLACK WHITE STRIP wire on the W 85 wall control Secure this connection with a wire 3 GREENS BLACK WITH 5 v WHITE STRIPE BLACK WHITE nut v GROUND 120V AC BLACK WHITE NOTE The RED wire is not used in this BLACK prev meds application DO NOT remove the crimped cap FIGURE 1 from the wire 2 BLACK WIRES W 85 6 Connect the second BLACK wire that you just Wall Control removed from the switch to the second BLACK wire on the loc
Download Pdf Manuals
Related Search