Cabela's PRECISE CUT 52-0601 User's Manual
Contents
1. ATTENTION If any components of this unit are broken or the unit does not operate properly please contact Cabela s Customer Service Retail Store Purchases 1 800 905 2731 U S amp Canada Catalog and Internet Purchases 1 800 237 8888 All International 1 308 234 5555 DO NOT RETURN THE UNIT TO THE STORE WHERE IT WAS PURCHASED PRECISE CUT ARROW SAW WITH DUST COLLECTING ATTACHMENT INSTRUCTION BOOK MODEL NO 52 0601 REVOS1711 COMPONENT LIST ARROW SAW BLADE REPLACEMENT DIAGRAM PART PART NO WARNING Before cleaning assembling or disassembling the Arrow NUMBER DESCRIPTION NUMBER Saw make sure it is turned OFF and the PLUG IS REMOVED FROM THE p ry OUTLET POWER SOURCE 1 Cutting Blade 2 52 0301 2 i Your Arrow Saw comes complete with two reinforced Cutting Blades Pn Toeter meee Senet These Cutting Blades are ideal for cutting both carbon and aluminum 3 Shaft Position Bracket 52 0305 arrow shafts To order replacement Cutting Blades contact Customer 4 Measuring Tape 52 0316 Service at the telephone number listed on the back of this manual 5 Socket Head Cap Screw 52 0320 1 Set the On Off Power Switch to the OFF AEN 6 Power Cord N A position Disconnect the Power Cord from the power source 1 On Off Switch N A 8 Dust Collector 52 0331 2 Loosen the two Thumb Screws holding the Blade Shield to the A Figure 9 Dust Collector Bracket 52 0332 OE Oy A eee ae 10 Thumb Screw 2 52 0333 3 Remove2. REMEMBER YOUR PERSONAL SAFETY IS YOUR RESPONSIBILITY 1 Check for damaged parts BEFORE using the Arrow Saw check that all parts are operating properly and perform their intended functions Check for alignment of moving parts binding of moving parts and any other condition that may affect the Arrow Saw operation 2 ALWAYS DISCONNECT Arrow Saw from power source before servicing changing accessories or cleaning the unit 3 To Reduce risk of unintentional starting make sure the power switch is in the OFF position before connecting the Arrow Saw to the power source 4 DO NOT IMMERSE THE ARROW SAW INTO WATER OR OTHER LIQUID OR OPERATE NEAR A WATER SOURCE SERIOUS INJURY FROM ELECTRIC SHOCK COULD RESULT 5 DO NOT operate the Arrow Saw with wet hands or bare feet 6 The Arrow Saw is not a toy KEEP CHILDREN AWAY fromthe unitatALL times NEVER LEAVE THE UNIT UNATTENDED DURING OPERATION 7 Keep fingers clear of the Cutting Blade at all times NEVER reach into the Arrow Saw with fingers or other objects Doing so may result in personal injury or unit damage 8 Any improper use or modification of the Arrow Saw will void the warranty 9 DO NOT attempt electrical repairs Any electrical repair mustbe done by an authorized service technician If your Arrow Saw needs repairing contact Customer Service 10 DO NOT operate the Arrow Saw if it is damaged or malfunctions in any way Instead please call Cust
3. c clamps Not Included May be used FIGURE 1 B Mounting Holes VACUUM ATTACHMENT INSTRUCTIONS The Arrow Saw comes with two Dust HGURE 2 Collector Adapters Use the appropriate size Dust Collector Adapter for the vacuum hose you want to connect 1 Set the ON OFF Switch to the OFF position 2 Unplug the Power Cord from the power source Dust Dust Vacuum Collector Collector Hose 3 If you are using the Small Dust nae Collector Adapter connect the large end to the Dust Collector Figure 2 If you are using the Large Dust Collector Adapter connect the small end to the Dust Collector 4 Firmly insert the vacuum hose end into the open end of the Dust Collector Adapter 5 Make sure all connections between the Arrow Saw Dust Collector Adapter and vacuum hose are secure MEASURING TAPE APPLICATION WARNING Before cleaning assembling or disassembling the Arrow Saw make sure it is turned OFF and the PLUG IS REMOVED FROM THE fy OUTLET POWER SOURCE The Arrow Saw with Dust Collecting Attachment comes without the Measuring Tape applied Carefully follow these instructions to apply the Measuring Tape to ensure you get the best results from your Arrow Saw 1 Place the Arrow Saw on a flat level non skid work surface 2 Clean the front face of the Base to remove any dirt or grime that may have accumulated during manufactu
4. to the Base Figure 7 Thumb Screw Arrow Shaft humb Screws 5 Adjust the Arrow Shaft Guide until the Guide Cutting Blade extends about 1 16 PAST a fully FIGURE 7 cut arrow shaft Figure 7 6 Firmly tighten the Socket Head Cap Screw to secure the Arrow Shaft Guide to the Base 7716 PAST 7 Replace the Blade Shield CAUTION NEVER OPERATE THE ARROW SAW arrow WITHOUT THE BLADE SHIELD SECURELY shafi MOUNTED IN PLACE Cutting Blade Arrow Shaft 8 Secure the Blade Shield to the Arrow Saw OE aos ects with the Thumb Screws Cap Screw Arrow Shaft 9 Check cutting depth to verify no movement occurred while securing the Arrow Shaft Guide or replacing the Blade Shield 10 Verify the On Off Power Switch is in the OFF position and connect the Arrow Saw to the power source Turn the attached vacuum on 11 Turn on the Arrow Saw and allow a few seconds for the Motor to reach full speed WARNING ALWAYS stand clear of the Cutting Blade during start up CAUTION ROTATING SHARP BLADE To avoid severe injury keep fingers hands and other foreign objects clear of the saw opening Blade and Moving Parts of the Arrow Saw Wear approved Safety Glasses and Kevlar Gloves when using the Arrow Saw MOUNTING INSTRUCTIONS For best results mount the Arrow Saw to a solid level surface to prevent excess vibration and movement during use There are two holes in the Base for this purpose Figure 1 As an alternative
5. 9 Re install the Blade Spacer and Blade Retaining Nut 10 Re install the Arrow Shaft Guide and Blade Shield CAUTION NEVER OPERATE i aki R taining THE ARROW SAW WITHOUT THE BLADE Blade Nut Base SHIELD SECURELY MOUNTED IN PLACE Spacer The Arrow Saw Cutting Blade rotates at very high speeds It is normal for the Arrow Saw to vibrate during operation If you experience excessive noise and or vibration during operation or blade breakage check all parts to ensure they are properly and securely mounted If the problem continues please contact Customer Service 2 11 8 Secure the Blade Shield to the Arrow Saw with the Thumb Screws 9 Check cutting depth to verify no movement occurred while securing the Arrow Shaft Guide or replacing the Blade Shield 10 Verify the On Off Power Switch is in the OFF position and connect the Arrow Saw to the power source Turn the attached vacuum on 11 Turn on the Arrow Saw and allow a few seconds for the Motor to reach full speed WARNING ALWAYS stand clear of the Cutting Blade during start up 14 Gently guide the arrow shaft into the Cutting Blade Rotate the arrow shaft until it is completely cut Figure 11 15 Carefully remove the cut arrow shaft from the Arrow Shaft Guide and Shaft Position Bracket Be careful to not allow the arrow shaft to further contact the Cutting Blade 16 Turn the Arrow Saw to the OFF Position Turn off the attached vaccuum Disconnect from
6. g Arrow Shaft the Arrow Shaft Guide to the Base Figure 10 Guide Thumb Screws FIGURE 10 5 Adjust the Arrow Shaft Guide until the Cutting Blade extends about halfway through the arrow shaft Figure 7 Halfway through poi 6 Firmly tighten the Socket Head Cap Screw the ade to secure the Arrow Shaft Guide to the Base Shaf 7 Replace the Blade Shield CAUTION NEVER OPERATE THE ARROW SAW A WITHOUT THE BLADE SHIELD SECURELY I Arrow Shaft MOUNTED IN PLACE sate la Cap Screw 9 There are two methods you can employ to cut arrow shafts One method is a THROUGH CUT for quickly cutting arrow shafts The other is a ROLL CUT for more precise cleaner cuts WARNING Before cleaning assembling or disassembling the Arrow Saw make sure it is turned OFF and the PLUG IS REMOVED FROM THE ey OUTLET POWER SOURCE 1 Set the On Off Power Switch to the OFF position Disconnect the Power Cord from the power source Wear eye protection at all times while Arrow Saw is in use Everyday eye glasses are not safety glasses Safety glasses confirm to ANSI Z87 z requirements Approved safety glasses have Z87 printed or stamped on them 2 Loosen the two Thumb Screws holding the Blade Shield to the Blade Shield FIGURE 6 Arrow Saw Figure 6 3 Remove the Thumb Screws and Cutting Blade Shield 4 Using an Allen Wrench loosen but do not remove the Socket Head Cap Screw securing the Arrow Shaft Guide
7. l it is completely cut Figure 8 14 Carefully remove the cut arrow shaft from thesArrow Shaft Guide and Shaft Position Bracket Be careful to not allow the arrow shaft to further contact the Cutting Blade 15 Turn the Arrow Saw to the OFF Position Turn off the attached vaccuum Disegnnegtdiom the power source when not in use Di FIGURE 8 Shaft Position Arrow Shaft Bracket CAUTION ROTATING SHARP BLADE D To avoid severe injury keep fingers hands and other foreign objects clear of the saw opening Blade and Moving Parts of the Arrow Saw Wear approved Safety Glasses and Kevlar Gloves Z when using the Arrow Saw Arrow Shaft Guide WARNING Before cleaning assembling or disassembling the Arrow Saw make sure it is turned OFF and the PLUG IS REMOVED FROM THE M OUTLET POWER SOURCE Wear eye protection at all times while Arrow Saw is in use Everyday eye glasses are not safety glasses Safety glasses Lazy confirm to ANSI Z87 z requirements ic Approved safety glasses have Z87 printed or stamped on them 1 Set the On Off Power Switch to the OFF position Disconnect the Power Cord from the power source FIGURE 9 2 Loosen the two Thumb Screws holding the Blade Shield to the Arrow Saw Figure 9 3 Remove the Thumb Screws and Blade Shield 4 Using an Allen Wrench loosen but do not remove the Socket Head Cap Screw securin
8. loves OPERATING INSTRUCTIONS WARNING Before cleaning assembling or disassembling the Arrow Saw make sure it is turned OFF and the PLUG IS REMOVED FROM THE ry OUTLET POWER SOURCE AND WARNINGS PRIOR TO USING THIS SAW YOUR SAFETY IS MOST IMPORTANT FAILURE TO COMPLY WITH PROCEDURES AND SAFE GUARDS WARNINGI may RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE REMEMBER YOUR PERSONAL SAFETY IS YOUR RESPONSIBILITY READ AND FULLY UNDERSTAND ALL INSTRUCTIONS Wear eye protection at all times while Arrow Saw is in use Everyday eye glasses Ware not safety glasses Safety glasses 1 Place the Arrow Saw ona flat level work surface Ka Sonn on ToT ee printed or stamped on them 2 Place the Shaft Position Bracket onto the Base Shafi Position 3 Locate the left face of the Shaft Position Bracket FIGURE 4 Bracket at the line on the Measuring Tape Wing Nut indicating the length of shaft you want to cut For example if you want to cut a 31 long arrow shaft locate the Shaft Position Bracket face at the 31 mark Figure 4 4 Secure the Shaft Position Bracket to the Base by tightening the Wing Nut Bracket Slowly tighten the Wing Nut while firmly Face holding the Shaft Position Bracket to prevent the Shaft Position Bracket from moving Base 5 Continue to the THROUGH CUTS or ROLL CUTS section of this manual WARNING Be sure to follow ALL SAFETY WARNINGS and preca
9. omer Service 11 Tie back loose hair and clothing roll up long sleeves and remove ties and rings bracelets and other jewelry before operating the Arrow Saw 12 DO NOT use the Arrow Saw if the power cord is frayed or damaged in any way 13 Keep the power cord well clear of the Arrow Saw blade during operation 14 DO NOT operate Arrow Saw while under the influence of drugs or alcohol 15 The Arrow Saw is for household use only Commercial use of the Arrow Saw will void the warranty 16 Only operate the Arrow Saw on a flat stable work surface 17 NEVER install any accessories or parts from other manufacturers on the Arrow Saw Doing so may damage the unit and will void the warranty 18 ALWAYS make sure the Cutting Blade is properly secured before operating the Arrow Saw Always stand clear of the Cutting Blade during start up 19 ALWAYS clean the area near the Cutting Blade Keep it clear of dust and debris to prevent damaging the blade 20 Wear eye protection at all times while the Arrow Saw is in use Everyday eye glasses are not safety glasses Safety glasses confirm to ANSI Z87 z requirements Approved safety glasses have Z87 printed or stamped on them SAVE THESE INSTRUCTIONS Refer to them to instruct others 12 Place the nock insert end of the arrow shaft into the notch in the Shaft Position Bracket Figure 8 13 Gently guide the end of the arrow shaft to be cut into the Cutting Blade unti
10. ring Shaft 3 Place the end of a tape measure Position FIGURE 3 firmly against the right side of the Bracket Cutting Blade Figure 3 4 Measure 6 15 2 cm from the Blade to the back face of the notch in the Shaft Position Bracket 5 Using the left face of the Shaft Position Bracket as a guide mark the Base with a pencil Vol Vad 6 Cut the Measuring Tape at the 5 mark Figure 3 Right Side Left rant Measuring of Face 1 7 Peel about 4 10 2 cm of the Tape Curing of Shaft p backing off of the Measuring Tape Blade Position PaE exposing the adhesive surface Bracket 8 Line up the 6 indicator line on the Measuring Tape with the left side of the Shaft Position Bracket The top of the Measuring Tape should be about 1 2 1 3 cm below the top of the Base Carefully apply the Measuring Tape a few inches at a time Continue peeling off the backing as necessary 9 Be sure to apply the Measuring Tape level and without air bubbles or creases Such irregularities will result in inaccurate shaft length measurements WARNING Be sure to follow ALL SAFETY WARNINGS and precautions that are contained in this instruction manual before using this when using the Arrow Saw appliance CAUTION ROTATING SHARP BLADE To avoid severe injury keep fingers hands and other foreign objects clear of the saw opening Blade and Moving Parts of the Arrow Saw Wear approved Safety Glasses and Kevlar G
11. the Thumb Screws and Cutting eae Thumb Screws SS eS ES oh eA GES NO oO fF ON Small 1 1 4 3 2 cm Dust Collector Adaptor Large 2 1 4 5 7 cm Dust Collector Adaptor Arrow Shaft Guide Electric Motor 8000 RPM Rubber Feet Wrench Kit Blade Mounting Bracket Assembly 17a Blade Spacer 52 0340 52 0341 52 0306 52 0202 52 0329 52 0330 52 0314 Blade Shield 3 Remove the Socket Head Cap Screw securing the Arrow Shaft Guide to the Base Figure 14 4 Remove the Arrow Shaft Guide 5 Insert the long leg of the largest Allen Wrench supplied with your Arrow Saw into one of the holes in the outer edge of the Blade Mounting Bracket Figure 15 FIGURE 14 arron a a uide 17b Blade Retaining Nut 6 Place the Wrench onto the Blade Retaining e ead Nut While holding the Allen Wrench loosen f the Blade Retaining Nut rotate counter clockwise until you can remove it by hand Blade Mounting Cutting 7 Remove the Blade Retaining Nut Blade Bracket Blade FIGURE 15 Spacer and Cutting Blade Wrench 8 Carefully install a new Cutting Blade CAUTION NEVER USE A BROKEN WORN Before beginning the assembly check the package contents for all of the parts If you are missing any parts or if any parts are damaged contact Cabela s Customer Service Retail Store Purchases 1 800 905 2731 U S amp Canada Catalog amp Internet Purchases 1 800 237 8888 All International 1 308 234 5555 OR CRACKED BLADE
12. the power source when not in use Cutting Blade FIGURE 11 Arrow Shaft Shaft Position Bracket Arrow Shaft Guide The Arrow Saw comes with 2 Spin Testers that allow you check the straightness of arrow shafts 1 Place the Spin Testers onto the Base Using an arrow shaft as a guide position the Spin Testers within 1 of each end of the shaft 2 Set the arrow shaft onto the Spin Testers 3 Spin the arrow shaft in either direction by rolling your thumb perpendicularly across the shaft at about the middle Figure 12 4 If the arrow shaft is true straight it will spin smoothly without any bounce or excess movement 5 Ifthe arrow bounces or does not spin true straight the arrow shaft is faulty and should be discarded Spin Testers Arrow Shaft FIGURE 12 Tr Trrrsrs tsrtststtrtstttdty i oe 10 WARNING Before cleaning assembling or disassembling the Arrow Saw make sure it is turned OFF and the PLUG IS REMOVED FROM THE M OUTLET POWER SOURCE Vacuum and vacuum hose not included 2 i 3 _ u GENERAL SAFETY RULES READ AND FULLY UNDERSTAND ALL USING THIS SAW YOUR SAFETY IS MOST 1 INSTRUCTIONS AND WARNINGS PRIOR TO IMPORTANT FAILURE TO COMPLY WITH PROCEDURES AND SAFE GUARDS MAY WARNING RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE
13. utions that CAUTION ROTATING SHARP BLADE Sre Contained in this To avoid severe injury keep fingers hands and other foreign 5 A objects clear of the saw opening Blade and Moving Parts of the instruction manual Arrow Saw Wear approved Safety Glasses and Kevlar Gloves before using this when using the Arrow Saw appliance
Download Pdf Manuals
Related Search