Audiovox PRO 2000 User's Manual
Contents
1. SAJE SE SSS RF Programmable Features Feature Selection 1 Chirp 2 Chirps ist DoorL UL 1 Sec 3 5 Sec 2nd Accy Lock Auto Lock On Auto Lock Off 3rd Accy UL Auto UL Dr Auto UL All 4th Passive Locks Passive Active 5th Pass Act Arm Passive Arm Active Arm 6th Voltage Sense On Off 7th Siren Horn O P Siren amp Horn Siren Only 8th Horn Chirp 10ms 16ms 9th Override Method Custom Code Valet 10th Two Step Unlock On Off 11th Chp From Tx On Off 12th Keyless Or Alarm Keyless Alarm To program these selectable features Action Turn ignition on Press and release the valet switch 3 times Within 3 seconds turn ignition Off Then On Press transmitter Lock button to change Press transmitter Lock button to change Press transmitter Lock button to change Press transmitter Lock button to change or Press and release the valet switch Press transmitter Lock button to change or Press and release the valet switch Press transmitter Lock button to change Press transmitter Lock button to change or Press and release the valet switch Press transmitter Lock button to change or Press and release the valet switch Press transmitter Lock button to change or Press and release the valet switch Press transmitter Lock button to change or Press and release the valet switch Press transmitter Lock button to change Press transmitter lock button to change or Press and release the valet switch Press transmitter Lock button to change Press transmitter L2. 3 chirps horn chirp output 30mS 4 chirp horn chirp output 40 mS 5 chirps horn chirp output 50mS 1 chirp horn chirp output 10 mS 2 chirps valet switch override operation 1 chirp custom code override operation 2 chirps 2 step unlock off 1 chirp 2 step unlock on 2 chirps chirp delete from transmitter inactive 1 chirp chirp delete from transmitter active 1 chirp keyless entry mode 2 chirp alarm mode Exit program mode Exit program mode Note Once you enter the feature programming mode do not allow more than 15 seconds to pass between steps or the programming will be terminated Note This system allows the transmitter to be programmed for single button lock unlock or separate button lock unlock The receiver is set up as follows Channel 1 Lock Unlock Unlock 2 amp Panic Unlock only if no button is programmed to Ch 2 Channel 2 If Programmed Unlock Unlock 2 amp Panic Channel 3 Channel 3 amp Alternate Channel 3 Channel 4 Channel 4 Output Channel 5 Channel 5 Output If so Equipped 128 6103 Front Page Released 7 24 01 During the program routine if a transmitter button is programmed into receiver channel 2 then the unit will always have separate lock unlock from that transmitter If during the program sequence receiver channel 1 is programmed and receiver channel 2 is skipped over as indicated in the transmitted program guide then the unit will operate as
3. a single button lock unlock unit from that transmitter It is possible to have one transmitter programmed for single button lock unlock and one transmitter programmed for separate button lock unlock if the customer so desires If you inadvertently incorrectly program the transmitter please read the information on reprioritizing found in the transmitter programming guide Valet Push ButtonSwitch HIH x To Shock Sensor Blue Pre Detect Green Trigger a Black Ground Red 12 Volts gt I LED ee m Door Lock Unlock Unlock 2 Red Lock Unlock Green Unlock Lock Red Black 2nd Unlock Existing Low Current Start Solenoid Wire To Start From Ignition K Solenoid Switch Hood Or Trunk Pin Switch Red Orange Dk Green Low Current Negative Black White Output To Operate 1 To 12 Volt Horn Relay Ign Crank Negative Trigger Input one 1 7 K gt Existing Negative Lt Green Zone F Door Pin Switch Connect To Optional GM Type Negative Triggering Device 7 et To Entry Green w White Illumination Wire Of Vehicle To Fused 12 Volt a Volt Supply Source onnect To Constant Battery Connect To 12 Volts Source If Vehicle S
4. ock button to change Press transmitter Lock button to change Press transmitter Lock button to change or inth Press and release the valet switch Press transmitter Lock button to change or Tenth Press and release the valet switch Press transmitter Lock button to change or Eleventh Press and release the valet switch Press transmitter Lock button to change or Twelfth Press and release the valet switch Press transmitter Lock button to change or Press and release the valet switch or Turn ignition key off Model PRO 2000 Short Manual 4 Chirps 5Chirps Default 1 Sec L Dbl U L Dbl L 1 Sec U L Dbl L Dbl U L 1 Sec Off Auto UL Off Off Active Active Off S amp H 16ms Valet Off Off Keyless System Response No response 1 Chirp LED 1 flash Short chirp then long chirp 1 chirp 1 second door locks 2 chirps 3 5 second door locks 3 chirps 1 sec lock dbl 1 sec unlock 4 chirps 1 sec unlock dbl 1 sec lock 5 chirps dbl 1 sec lock dbl 1 sec unlock 2 chirps auto locks off 1 chirp auto locks on 3 chirps auto unlock off 1 chirp auto unlock drivers door only 2 chirps auto unlock all doors 2 chirps active door locks 1 chirp passive door locks 2 chirps active arming 1 chirp passive arming 2 chirps voltage sense off 1 chirp voltage sense on 1 chirp siren and horn output 2 chirps siren output only 3 chirps horn output only 2 chirps horn chirp output 16mS
5. witches 12 Volts To The Interior Light ae a Connect To Ground pasing peat If The Vehicle Switches FordType Ground To The Vehicles Altemate Channel 3 Blue Black Low Current Output For Remote Start Interface Ignition Source Connect To 12 Volts Yellow Ignition Crank Channel 4 G Black Negative Pulsed Or neon Switched Output Responsive To Transmitter Activation 7 Duration Chassis Ground CHANNEL 3 Low Current Dark Blue Negative Pulsed Output For Optional Remote Start Trunk Release Window Roll Up 128 6103 Back Page
Download Pdf Manuals
Related Search