AMX UDM-RX02 User's Manual
Contents
1. an EFA Overview Installed at the display device the UDM RX02 FG UDM RX02 converts the signal received from a UDM Multi Format Distribution Hub to standard A V signals FIG 1 ENDELEO UDM RX02 FIG 1 UDM RX02 With all the same features of the UDM RX01 the UDM RX02 adds support for Common mode sync as well as remote power for long cable distance runs Compatibility The UDM RX02 is compatible for use with the following UDM Hubs e UDM 0102 FG UDM 0102 This hub supports Common Synch Mode e UDM 0404 FG UDM 0404 This hub supports Common Synch Mode e UDM 1604 FG UDM 1604C This hub supports Common Synch Mode e UDM 1604 FG UDM 1604 This hub does not support Common Synch Mode In this case the UDM RX02 will function but without Common Synch Mode Product Specifications UDM RX02 Specifications 24VDC 75A Note In most cases the UDM RX02 is remotely powered by the UDM Multi Format Distribution Hub see Powering on the UDM RX02 Power Requirements Rear Panel Connectors Power Socket 2 1mm barrel style DC power socket female UDM Hub RJ45 Provides audio video transport as well as control via Cat5 Cat5e or Cat6 to an UDM Hub Port Serial RJ12 port Enables an administrator to control the various functions to the UDM RX02 from a command line prompt and termi nal connection e Requires a DB9 to RJ12 adapter cable FG RS01 to connect to a PC 9600 8 bit No Parity 1 S2. RX02 is attached to is configured correctly within the Hub s configuration software Also ensure the correct Audio Type Analog L R S PDIF or None is selected for the relevant input UDM HUB Port LEDs 2 LEDs are visible at the UDM Hub port on the UDM RX02 when the UDM 0102 is switched on e Green Connection to UDM 0102 if Cat 5 removed LED switches off Amber Power as well as comms if uploading protocols etc the Amber LED may flicker For full warranty information refer to the AMX Instruction Manual s associated with your Product s 2 08 2008 AMX All rights reserved AMX and the AMX logo are registered trademarks of AMX AMX reserves the right to alter specifications without notice at any time 3000 RESEARCH DRIVE RICHARDSON TX 75082 800 222 0193 fax 469 624 7153 technical support 800 932 6993 www amx com Powering on the UDM RX02 The UDM RX02 may be powered by its hub device through a standard CAT5 cable but it may also be powered through an optional 24 VDC power supply FG UDM PS intended to augment power for very long cable runs To connect the UDM RX02 to the optional power supply insert the barrel connector of the power supply into the power connector on the UDM RX02 see FIG 2 To power down the UDM RX02 remove the barrel connector of the power supply from the power connector and then remove the Ethernet cable from the UDM Hub connector Note Disconnecting the optional power supply
3. the UDM RX02 2 Run the other end of the composite cable to the Composite connector normally yellow on the display device Connect firmly 3 If appropriate connect audio to the audio connectors on the UDM RX02 SVideo Input at Display Device 1 Attach the SVideo cable to the 4 pin S Video connector on the UDM RX02 2 Run the other end of the SVideo cable to the SVideo connector on the display device Connect firmly 3 If appropriate connect audio to the audio connectors on the UDM RX02 Component Input at Display Device 1 Attach the Component cables normally green blue and red to the Y green Pb blue and Pr red connectors on the UDM RX02 2 Run the other end of the Component cable to the Component connectors nor mally green blue and red on the display device Connect firmly 3 If appropriate connect audio to the audio connectors on the UDM RX02 Audio amp Video Formats Resolutions Distance Audio amp Video Formats Resolutions Distance Class Format Name Distance em r 720x576 300 m 1000 1280x720 300 m 1000 300 m 1000 300 m 1000 300 m 1000 300 m 1000 Component 1920x1080 1080i 640x480 When using VGA modes with audio enabled the maximum cable distance is approximately 200 m 650 Note The maximum distances indicated above are not absolute but are recommended distances that have been tested to deliver video at the specified resolutions w
4. will not power down the UDM RX02 if its Ethernet connection to the UDM Hub ts intact System Overview FIG 3 provides a basic system diagram representing a UDM 0102 Hub UDM RX02 Receiver and connected devices Video Out Audio Out Video Out Audio Out Video In Audio In Video In UDM Hub Audio In Ethernet network Cats UDM Receiver Video Out Audio Out Video In Audio In Display FIG 3 UDM System Diagram Additional Documentation Refer to the UDM 0102 and UDM RX02 Multi Format Distribution Hub and Receiver Operation Reference Guide available online at www amx com for detailed information on configuring the Hub UDM receivers and source devices 93 UDM RX02 REV F NI MUNI URUY 10E VIET TM TOT E M Aa AR
5. DM Hub s Operation Reference Guide for details Rear Panel Components All of the connectors and ports are located on the rear panel FIG 2 Composite Pr port UDM HUB port RJ45 from an Composite Pb port OUTPUT port on the UDM 0102 Composite Y port VGA HD15 port S Video SVIDEO AA UDM HUE SERML A aro f CVES RCA audio left right SPDIF female Digital Audio port FIG 2 UDM RX02 rear panel components UDM Hub Port RJ45 The UDM RX02 connects to a UDM Hub through a Cat 5 Cat 6 connection Refer to the UDM Hub s Operation Reference Guide for details Power connector Serial Port The Serial port is available for diagnostic and troubleshooting purposes The Serial port on the UDM RX02 is an RJ12 connector and requires a DB9 to RJ12 adapter cable FG RSO01 to connect to a PC for Terminal control IR Receiver IR Rx Port The IR Rx port is used to enable user control and the remote compensation of the video link to the UDM using the FG UDM RC10 and the FG IRO3 Refer to the Protocols and IR Learning section of the UDM Hub s Operation Reference Guide for details for information on learning a device s IR commands IR Transmit IR Tx Port The IR Tx port issues IR commands from the UDM RX02 to a controlled display device TV monitor or display One IR display device can be connected to the UDM RX02 via the IR Tx port and controlled via the UDM Hub s WebConsole or via remote control Co
6. ithout significant signal degradation In particular lower resolutions 640 x 480 720 x 480 and 800 x 600 can often be delivered significantly further than what is indicated in the table Refer to the UDM Hub s Operation Reference Guide for additional details on maximum cable distances Video Compensation Video at the Receive end can be compensated using three main methods e Using the UDM Hub s WebConsole e Using the UDM RCO2 Multi Format IR Remote Control e Using a hyper terminal session via the serial connector on the UDM RX02 especially effective setup method when using long runs Connecting an External IR Receiver Module If passthrough mode where a device such as a DVD or VCR can be controlled via a UDM RC02 Multi Format IR Remote Control is required then an IRO3 External IR Receiver Module will be needed to pick up IR controls from the remote control Additionally if the UDM RX02 is to be compensated via a remote control then an IR Receiver Module is also needed Connecting the UDM RX02 Receiver to the UDM Hub The RJ45 port on the front panel of the UDM 0102 Hub labelled UDM supports one UDM RX02 Receiver The UDM RX02 is then be connected to a display device 1 Connect a standard Cat5 6 Ethernet cable to the RJ45 port labelled UDM on the front panel of the UDM hub 2 Connect the other end of the Ethernet cable to the RJ45 port labelled UDM Hub on the rear panel of the UDM RX02 Note Ensure the UDM Hub port the
7. nnecting an IR Device to the IR Tx Port 1 Connect an IRO1 Endeleo IR Emitter Module FG IRO1 to the IR Tx port on the UDM RX02 Note Ensure the position of the device corresponds to the position assigned in the Devices option of the UDM Hub s WebConsole 2 Run the other end of the IR Emitter cable to the device s IR sensor and attach the IR Emitter to the device s sensor by removing the cover on the reverse side of the IR Emitter IR commands for each device on the system have to be learned by the UDM 0102 in order to function properly Refer to the Protocols and IR Learning section of the UDM Hub s Operation Reference Guide for information on learning a device s IR commands AUDIO Connectors The UDM RX02 provides standard Audio RCA output connectors for S PDIF for digital audio and LEFT RIGHT for analog audio output FIG 2 VIDEO Connectors VGA Input at Display Device 1 Attach one end of the VGA cable to the VGA connector on the UDM RX02 2 Run the other end to the VGA connector on the display device Connect firmly 3 If appropriate connect audio to the audio connectors on the UDM RX02 Note Ensure the UDM Hub port the RX02 is attached to is configured correctly within the Hub s configuration software Also ensure the correct Audio Type Analog L R S PDIF or None is selected for the relevant input Composite Input at Display Device 1 Attach the composite cable normally yellow to the CVBS connector on
8. top Bit IR Rx Port 3 5mm stereo input port for connection of an IR receiver to allow setup of the UDM RX02 local compensation controls and remote control of centrally located IR devices IR Tx Port 3 5mm stereo IR Transmitter output port allows one IR controlled device such as a DVD or VCR player to be controlled via optional wired IR emitter Audio Connectors Black RCA female connector Digital audio White RCA female connector Analog audio Left Red RCA female connector Analog audio Right Video Connectors Yellow RCA female connector CVBS supports composite video S Video S video female connector VGA HD15 female connector supports VGA video Green RCA female connector Component output Y Blue RCA female connector Component output Pb Red RCA female connector Component output Pr 35 F 95 F 5 C 35 C e Max relative humidity 85 non condensing Dimensions HWD 1 x 8 15 16 x 3 3 8 25 mm x 227 mm x 85 mm Certifications e CE e FCC part 15 Class A Other AMX Equipment RS232 DB9 RJ12 Connection Cable FG RSO1 e UDM RCO2 Multi Format IR Remote Control FG UDM RCO2 e IRO1 IR Emitter Module FG IRO1 e RO3 External IR Receiver Module FG IRO3 e UDM PS 24VDC 750mA Power Supply FG UDM PS Operating Environment Quick Start Guide UDM RX0O2 Endeleo Multi Format Receiver Configuration The UDM RX02 is configured via the UDM Hub s WebConsole Refer to the U
Download Pdf Manuals
Related Search