American Standard Reliant+ 4205.001 User's Manual
Contents
1. attach COUPLING NUT 3 of HOSE 1 to HOSE ADAPTOR 4 on valve body Tighten COUPLING NUT 3 firmly Make certain that SPACER WASHER 5 and RUBBER WASHER 6 are attached to SPRAY HOSE 1 and thread SPRAY HEAD 7 to NUT 8 TEST INSTALLED FAUCET Remove AERATOR With handles in OFF position turn on water supplies and check all connections for leaks Operate HANDLE to flush water lines thoroughly Rotate SPOUT in both directions Replace AERATOR Direct SPRAY HEAD into sink and activate SPRAY Check HOSE connections for leaks SERVICE If faucet drips proceed as follows Turn VALVE in OFF position If faucet drips operate handle several times from off to on Do not apply excessive force Clogged CARTRIDGE inlets may cause reduced flow in full on hot or cold To clean inlets first turn off water supply then Remove HANDLE 1 CAP 2 CARTRIDGE 3 and DISC amp SEALS 5 Clean inlets and MANIFOLD 4 Reassemble CARTRIDGE 3 alternately tightening screws Replace CAP and HANDLE Check flow HOT LIMIT SAFETY STOP ADJUSTMENT By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold the HOT LIMIT SAFETY STOP reduces risk of accidental scalding To set the maximum hot water temperature of your faucets all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP a Use a flat blade screwdriver or your fingers to pull up and rotate PRY RED RING FORWARD red HOT LIM2. Americam Standard Installation Instructions 4205 000 Reliant 4205 001 SINGLE CONTROL KITCHEN FAUCETS Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Certified to comply with ASME A112 18 1M M968420 REV 1 1 TOOLS REQUIRED rO Ss mae Channel Locks Adjustable Wrench Plumbers Putty or Caulking Phillips Screwdriver INSTALL FAUCET SECURE FAUCET AND MAKE Fan GF water SE WATER SUPPLY CONNECTIONS CAUTION NOTE FLEXIBLE SUPPLIES 3 4 HAVE TO BE PURCHASED SEPARATELY Secure FAUCET 1 with ATTACHMENT NUTS 2 supplied E Install FAUCET 1 on sink No sealant is required HAND TIGHTEN unless mounting deck on SINK is uneven Connect water supply to FAUCET 1 with 1 2 IPS FLEXIBLE SUPPLIES 3 or 3 8 0 D BULL NOSE RISERS 4 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink copper supply when bending Use tubing cutter to cut to proper length 2 HAND TIGHTEN SINK OR DECK ee T a COUPLING NUT FERRULE 3 FITTING WITH SPRAY m Place SPRAY HOLDER 1 into separate hole of SINK 2 and assemble NUT 3 onto shank E From underside of SINK 2 and hand tighten NUT 3 FITTING WITH SPRAY Feed SPRAY HOSE 1 through SPRAY HOLDER 2 and
3. IT SAFETY STOP 5 Follow Step A or B to adjust NOI er ONE CUCK min max discharge temperature 0 being the hottest to 7 lt i A the coldest temperature setting Factory set at 0 TEMPERATURE A SETTING NUMBERS oO ADJUSTMENT WHEN B PRY RED RING FORWARD AND ROTATE CLOCKWISE B ADJUSTMENT WHEN WATER IS TOO COLD RED RING HOT LIMIT SAFETY STOP 7 CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE M968420 REV 1 1
Download Pdf Manuals
Related Search