Zanussi ZFU20200WA freezer
Contents
1. Unscrew the upper pin 1 and place it on the opposite side 2 Refit the door 11 Stand the appliance upright Unscrew the handle 1 and fix it on the op posite side 2 Re insert the cover pins 3 on the opposite side Environmental concerns A The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent 12 Do afinal check to make sure that All screws are tightened The edges of the doors run parallel to the side edge of the appliance The magnetic seal adheres to the cabinet The door opens and closes correctly It is advisable to wait at least four hours before connecting the appliance to allow the oil to flow back in the compressor If the ambient temperature is cold i e in Win ter the gasket may not fit perfectly to the cabi net In that case wait for the natural fitting of the gasket In case you do not want to carry out the above mentioned operations contact the nearest After Sales Service Force The After Sales Service specialist will carry out the reversibility of the doors at your cost potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste ha2. Control panel 4 This product must be serviced by an author ized Service Centre and only genuine spare parts must be used Environment Protection This appliance does not contain gasses which could damage the ozone layer in ei ther its refrigerant circuit or insulation materials The appliance shall not be discarded together with the urban refuse and rubbish The insula tion foam contains flammable gases the appli ance shall be disposed according to the appli cable regulations to obtain from your local au thorities Avoid damaging the cooling unit es pecially at the rear near the heat exchanger The materials used on this appliance marked by the symbol are recyclable www zanussi com Freezer baskets Rating plate Control panel Maxibox baskets Alarm Light Fast Freeze Indicator Fast Freeze Switch Pilot Light Temperature Regulator Switching on Insert the plug into the wall socket Turn the Temperature regulator clockwise to a medium setting The Pilot light and the Alarm light will light up Switching off To turn off the appliance turn the Temperature regulator to the 0 position Temperature regulation The temperature is automatically regulated To operate the appliance proceed as follows turn the Temperature regulator toward lower settings to obtain the minimum coldness turn the Temperature regulator toward higher settings to obtain the maxi
3. User manual Freezer U R MANUAL ZFU20200WA ZAN USSI Contents Safety instructions _ _______ Product description Control panel Daily use First use JO QI QI R N A Safety instructions In the interest of your safety and to ensure the correct use before installing and first using the appliance read this user manual carefully in cluding its hints and warnings To avoid unnec essary mistakes and accidents it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features Save these instructions and make sure that they remain with the appliance if it is moved or sold so that everyone using it through its life will be properly informed on ap pliance use and safety For the safety of life and property keep the pre cautions of these user s instructions as the manufacturer is not responsible for damages caused by omission Children and vulnerable people safety This appliance is not intended for use by per sons including children with reduced physi cal sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction con cerning use of the appliance by a person re sponsible for their safety Children should be supervised to ensure that they do not play with the appliance Keep all packaging well away from children There is risk of suffocation f you are discarding the appliance p
4. use before putting the products in the com partment let the appliance run at least 2 hours The freezer drawers ensure that it is quick and easy to find the food package you want If large quantities of food are to be stored remove all drawers except for the bottom drawer which needs to be in place to provide good air circu lation On all shelves it is possible to place food that protrude until 15 mm from the door Important In the event of accidental defrosting for example due to a power failure if the power has been off for longer that the value shown in the technical characteristics chart under rising time the defrosted food must be consumed quickly or cooked immediately and then re frozen after cooling Thawing Deep frozen or frozen food prior to being used can be thawed in the refrigerator compartment or at room temperature depending on the time available for this operation Small pieces may even be cooked still frozen directly from the freezer in this case cooking will take longer Removal of freezing baskets and glass shelves from the freezer Some of the freezing baskets have a limit stop to prevent their accidental removal or falling out At the time of its removal from the freezer pull the basket towards yourself and upon reaching the end point remove the basket by tilting its front uowards At the time of putting it back slightly lift the front of the basket to insert it into the freezer Once you ar
5. Wrap the food correctly Set a higher temperature 3 If necessary replace the defective door gaskets Contact the Service Center 2 If necessary adjust the door Refer to In stallation Technical data Dimension Rising Time Voltage Frequency Height Width Depth The technical information are situated in the rat ing plate on the internal left side of the appli ance and in the energy label Installation 1540 mm 595 mm 658 mm 20h 230 240 V 50 Hz Caution Read the Safety Information carefully for your safety and correct www zanussi com appliance operation of the appliance before installing the Positioning Install this appliance at a location where the ambient temperature corresponds to the cli mate class indicated on the rating plate of the appliance Climate Ambient temperature class SN 10 C to 32 C N 16 C to 32 C ST 16 C to 38 C T 16 C to 43 C Location The appliance should be installed well away from sources of heat such as radiators boilers direct sunlight etc Ensure that air can circulate freely around the back of the cabinet To ensure best performance if the appliance is positioned below an overhanging wall unit the minimum distance between the top of the cabinet and the wall unit must be at least 100 mm Ideally however the appliance should not be posi tioned below overhanging wall units Accurate levelling is ensured by one or mo
6. appliance is not working prop erly The temperature in the freezer is too high The temperature is not set correct ly The door is not closed correctly The door has been opened too fre quently Switch on the appliance Connect the mains plug to the mains socket correctly Connect a different electrical appli ance to the mains socket Contact a qualified electrician Contact a qualified electrician Refer to Excessive Temperature Alarm Set a higher temperature Refer to Closing the door Do not keep the door open longer than necessary www zanussi com The temperature in the freezer is too low The temperature in the freezer is too high There is too much frost Closing the door 1 Clean the door gaskets The product temperature is too high The room temperature is too high The temperature regulator is not set correctly The Fast Freeze function is switch ed on The temperature regulator is not set correctly Many products are stored at the same time Products are too near to each oth er Food is not wrapped correctly The temperature regulator is not set correctly Let the product temperature de crease to room temperature before storage Decrease the room temperature Set a higher temperature Refer to Fast Freeze function Set a lower temperature Store less products at the same time Store products so that there is cold air circulation
7. be tak en when moving it Do not remove nor touch items from the freezer compartment if your hands are damp wet as this could cause skin abrasions or frost freezer burns Avoid prolonged exposure of the appliance to direct sunlight Bulb lamps if foreseen used in this appli ance are special purpose lamps selected for household appliances use only They are not suitable for household room illumination www zanussi com Daily Use Do not put hot pot on the plastic parts in the appliance Do not store flammable gas and liquid in the appliance because they may explode Do not place food products directly against the air outlet on the rear wall If the appli ance is Frost Free Frozen food must not be re frozen once it has been thawed out Store pre packed frozen food in accordance with the frozen food manufacturer s instruc tions Appliance s manufacturers storage recom mendations should be strictly adhered to Refer to relevant instructions Do not place carbonated or fizzy drinks in the freezer compartment as it creates pressure on the container which may cause it to ex plode resulting in damage to the appliance Ice lollies can cause frost burns if consumed straight from the appliance Care and cleaning Before maintenance switch off the appliance and disconnect the mains plug from the mains socket Do not clean the appliance with metal ob jects Do not use sharp obj
8. e electricity supply voltage is the same as that indicated on the appli ance rating plate 6 Switch on the appliance The appliance is supplied with a 13 amp plug fitted B In the event of having to change the fuse in the plug supplied a 13 amp ASTA ap proved BS 1362 fuse must be used Warning A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that it is disposed of safely Rear spacers You can find the two spacers in the bag with documentation Do these steps to install the spacers mak Release the screw 2 Engage the spacer below the screw 3 Turn the spacer to the right position 4 Tighten again the screws a www zanussi com Levelling When placing the appliance ensure that it stands level This can be achieved by two ad justable feet at the bottom in front Door reversibility Important To carry out the following operations we suggest that this be made with another person that will keep a firm hold on the doors of the appliance during the operations To change the opening direction of the door do these steps Remove the plug from the power socket Tilt back the appliance carefully so that the compressor cannot touch the floor Remove the plinth 1 Remove the cap 2 and position it on the opposite side Unscrew and remove the lower hinges 3 Remove the door
9. e over the end points push the basket back in their position First use Cleaning the interior Before using the appliance for the first time wash the interior and all internal accessories with lukewarm water and some neutral soap so The appliance is equipped with shelf stops to secure the shelves The shelves must be lifted up 1 on each side and than pulled outwards 2 The glass shelves equipped with expander roll ers are secured with locking pins To remove them proceed as follow 1 Use a screwdriver to loosen the locking pin on each side on the expander roller 2 Then pull out both locking pin 1 Then pull the glass shelf outwards 2 as to remove the typical smell of a brand new product then dry thoroughly Important Do not use detergents or abrasive powders as these will damage the finish www zanussi com Helpful hints and tips Normal Operating Sounds You may hear a faint gurgling and a bubbling sound when the refrigerant is pumped through the coils or tubing This is correct When the compressor is on the refrigerant is being pumped around and you will hear a whirring sound and a pulsating noise from the compressor This is correct The thermic dilatation might cause a sudden cracking noise It is natural not dangerous physical phenomenon This is correct When the compressor switches on or switches off you will hear a faint click of the temperature regulator Thi
10. ects to remove frost from the appliance Use a plastic scraper Never use a hair drier or other heating appli ances to speed up defrosting Excessive heat may damage the plastic interior and humidity could enter the electric system making it live Installation Important For electrical connection carefully follow the instructions given in specific paragraphs Unpack the appliance and check if there are damages on it Do not connect the appliance if it is damaged Report possible damages immediately to the place you bought it In that case retain packing tis advisable to wait at least four hours be fore connecting the appliance to allow the oil to flow back in the compressor Adequate air circulation should be around the appliance lacking this leads to overheat ing To achieve sufficient ventilation follow the instructions relevant to installation Wherever possible the back of the product should be against a wall to avoid touching or catching warm parts compressor condens er to prevent possible burn The appliance must not be located close to radiators or cookers Make sure that the mains plug is accessible after the installation of the appliance Connect to potable water supply only If a water connection is foreseen Service Any electrical work required to do the servic ing of the appliance should be carried out by a qualified electrician or competent person Product description
11. g odour Clean the condenser black grill and the com pressor at the back of the appliance with a brush This operation will improve the perform ance of the appliance and save electricity con sumption Important Take care of not to damage the cooling system Troubleshooting Warning Before troubleshooting disconnect the mains plug from the mains socket Many proprietary kitchen surface cleaners con tain chemicals that can attack damage the plastics used in this appliance For this reason it is recommended that the outer casing of this appliance is only cleaned with warm water with a little washing up liquid added After cleaning reconnect the equipment to the mains supply Defrosting Your appliance is frost free This means that there is no buildup of frost when it is in opera tion neither on the internal walls nor on the foods The absence of frost is due to the continuous circulation of cold air inside the compartment driven by an automatically controlled fan Only a qualified electrician or competent person must do the troubleshooting that is not in this manual ICI TI CT The appliance does not operate The Pilot light does not flash The Pilot light flashes The Alarm light flashes The compressor operates continually The appliance is switched off The mains plug is not connected to the mains socket correctly The appliance has no power There is no voltage in the mains socket The
12. mum coldness Daily use Freezing fresh food The freezer compartment is suitable for freezing fresh food and storing frozen and deep frozen food for a long time To freeze fresh food activate the Fast Freezing function at least 24 hours before placing the food to be frozen in the freezer compartment Place the fresh food to be frozen in the top compartment www zanussi com The intermediate position is usually the most suitable However the exact setting should be chosen keeping in mind that the temperature inside the appliance depends on room temperature how often the door is opened the quantity of food stored the location of the appliance Fast Freeze function To activate the Fast Freeze function press the Fast Freeze switch The Fast Freeze light will light up Excessive Temperature Alarm In the event of an abnormal temperature rise in side the freezer e g power cut alarm light comes on When normal conditions are restored the alarm light will switch off automatically The maximum amount of food that can be fro zen in 24 hours is specified on the rating plate a label located on the inside of the fridge The freezing process lasts 24 hours during this period do not add other food to be frozen After 24 hours when the freezing process is completed deactivate the Fast Freezing func tion see Fast Freezing function Storage of frozen food When first starting up or after a period out of
13. ndling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product www zanussi com www zanussi com 13 14 www zanussi com www zanussi com 15 www zanussi com shop ES 8 i ZN fN 280151036 A 492012
14. ore better and longer than fatty ones salt reduces the storage life of food water ices if consumed immediately after re moval from the freezer compartment can possibly cause the skin to be freeze burnt it is advisable to show the freezing in date on each individual pack to enable you to keep tab of the storage time Hints for storage of frozen food To obtain the best performance from this appli ance you should make sure that the commercially frozen food stuffs were adequately stored by the retailer be sure that frozen foodstuffs are transferred from the foodstore to the freezer in the short est possible time not open the door frequently or leave it open longer than absolutely necessary once defrosted food deteriorates rapidly and cannot be refrozen do not exceed the storage period indicated by the food manufacturer ing must therefore only be carried out by au thorized technicians Periodic cleaning The equipment has to be cleaned regularly clean the inside and accessories with luke warm water and some neutral soap regularly check the door seals and wipe clean to ensure they are clean and free from debris rinse and dry thoroughly Important Do not pull move or damage any pipes and or cables inside the cabinet Never use detergents abrasive powders highly perfumed cleaning products or wax polishes to clean the interior as this will damage the surface and leave a stron
15. re adjustable feet at the base of the cabinet A Warning It must be possible to disconnect the appliance from the mains power supply the plug must therefore be easily accessible after installation E 100 mm 20 mm 10 Electrical Connection Caution Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Warning This appliance must be earthed The manufacturer declines any liability should these safety measures not be observed G N N Important The wires in the mains lead are coloured in accordance with the following code A Green and Yellow Earth C Brown Live D Blue Neutral As the colours of the wires in the mains lead of this appliance may not correspond with the col oured markings identifying the terminals in your plug proceed as follows 1 Connect the wire coloured green and yel low to the terminal marked either with the letter E or by the earth symbol or col oured green and yellow 2 Connect the wire coloured blue to the ter minal either marked with the letter N or coloured black www zanussi com 3 Connect the wire coloured brown to the terminal either marked with the L or col oured red 4 Check that no cut or stray strands of wire is present and the cord clamp E is secure over the outer sheath 5 Make sure th
16. s is correct Hints for energy saving Do not open the door frequently or leave it open longer than absolutely necessary Ifthe ambient temperature is high and the Temperature Regulator is set to low temper ature and the appliance is fully loaded the compressor may run continuously causing frost or ice on the evaporator If this happens set the Temperature Regulator toward warm er settings to allow automatic defrosting and so a saving in electricity consumption Hints for freezing To help you make the most of the freezing process here are some important hints the maximum quantity of food which can be frozen in 24 hrs is shown on the rating plate the freezing process takes 24 hours No fur ther food to be frozen should be added dur ing this period only freeze top quality fresh and thoroughly cleaned foodstuffs Care and cleaning Caution Unplug the appliance before carrying out any maintenance operation This appliance contains hydrocarbons in its cooling unit maintenance and recharg www zanussi com prepare food in small portions to enable it to be rapidly and completely frozen and to make it possible subsequently to thaw only the quantity required wrap up the food in aluminium foil or poly thene and make sure that the packages are airtight do not allow fresh unfrozen food to touch food which is already frozen thus avoiding a rise in temperature of the latter lean foods st
17. ull the plug out of the socket cut the connection cable as close to the appliance as you can and remove the door to prevent playing chil dren to suffer electric shock or to close themselves into it If this appliance featuring magnetic door seals is to replace an older appliance having Careandcleaning 7 Troubleshooting _______ _ 8 Technical data ______________ 9 Installation 2 __________________ 9 Environmental concerns 12 Subject to change without notice a spring lock latch on the door or lid be sure to make that spring lock unusable be fore you discard the old appliance This will prevent it from becoming a death trap for a child General safety A Warning Keep ventilation openings in the appliance en closure or in the built in structure clear of ob struction The appliance is intended for keeping food stuff and or beverages in a normal household and similar applications such as staff kitchen areas in shops offices and other working environments farm houses and by clients in hotels mo tels and other residential type environ ments bed and breakfast type environments catering and similar non retail applications Do not use a mechanical device or any artifi cial means to speed up the thawing process Do not use other electrical appliances such as ice cream makers inside of refrigerating appliances unless they are approved for this purpose by the manufact
18. urer Do not damage the refrigerant circuit The refrigerant isobutane R600a is con tained within the refrigerant circuit of the ap pliance a natural gas with a high level of en vironmental compatibility which is neverthe less flammable www zanussi com During transportation and installation of the appliance be certain that none of the com ponents of the refrigerant circuit become damaged If the refrigerant circuit should become dam aged avoid open flames and sources of ignition thoroughly ventilate the room in which the appliance is situated It is dangerous to alter the specifications or modify this product in any way Any damage to the cord may cause a short circuit fire and or electric shock Warning Any electrical component pow er cord plug compressor must be re placed by a certified service agent or qualified service personnel to avoid hazard 1 Power cord must not be lengthened 2 Make sure that the power plug is not squashed or damaged by the back of the appliance A squashed or damaged power plug may overheat and cause a fire 3 Make sure that you can come to the mains plug of the appliance 4 Do not pull the mains cable 5 If the power plug socket is loose do not insert the power plug There is a risk of electric shock or fire 6 You must not operate the appliance without the lamp cover if foreseen of interior lighting This appliance is heavy Care should
Download Pdf Manuals
Related Search