Home
Belling IDW604 MK2
Contents
1. gure 7 x Ni Installatlon of aesthetic panel St4 countersunk head screw Lower hook Figure4b 4X18 screw Cover Installation of aesthetic wooden panel Spacer for furniture door 1 Take away the cover 2 Pin up the screw 3 Get back the cover Hook for aesthetic door Outer door of dishwasher Furniture door e Tension adjustment of the door spring The door springs are set at the factory to the proper tension for the outer door lf aesthetic wooden panel are installed you will have to adjust the door spring tension Rotate the adjusting screw to drive the adjustor to strain or relax the steel cable see figure 5 Adjust the door spring tension until the door remains balance inthe fully opened position Lie AO N Figured Tension adjustment of the door spring e Connection of drain hoses Insert the drain hose into a drain pipe with a minimum diameter of 4cm or let it run into the sink making sure to avoid bending or crimping it Use the speical plastic support that comes with the appliance figure 6 The top of the hose must be at a height between 40 and 100cm The free end of the hose must not be immersed in water to avoid the back flow of it ATTENTION The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain Figure6 Drain pipe connection Close
2. I B Display window Program remaining time delay time running indicator Program indicator Salt and rinse aid indicator Error codes etc Delayed Start Button To preset the wash timer and delay the starting time up to 24 hours Every press of this button increases the time by one hour for example one press for an hour two for two hours 3in1 and half load function button To select and show 3in1 and Half load functions Half load function means that the lower spray arm does not run so you should load the upper basket only Program button To select one of the six programs Power switch To turn on off the power supply Dishwasher Features GES o y Front view o E fa 1 ip mu n SS NGA JEN Upper Basket Salt Container Spray Arms Main Filter Lower Basket 6 Detergent Dispenser o Ble Cup Shelf 8 Cutlery Basket 9 Coarse Filter 3 Back View Rinse Aid Dispenser Drain pipe connector Inlet pipe connector IMPORTANT To getthe best performance from your dishwasher read all operating instructions 4 Prior using for the first time Before using your dishwasher for the first time Set the water softener B Pour 1 2 litre of water inside the salt container and then fill with dishwasher salt Fill the rinse aid dispenser BA Fillin detergent A Water Softener The water softener must be set manually using the water hardness dia
3. Items are blocking the path of spray arms The filter combination in the base of wash cabinet is not clean or is not correctly fitted This may cause the spray arm jets to get blocked Combination of soft water and too much detergent Aluminum utensils have rubbed against dishes Dishes block detergent cups Improper loading Too little rinse aid Dishes are removed too soon Wrong program has been selected Use of cutlery with a low quality coating What To Do See notes in Loading the Dishwasher Baskets Select a more intensive programme See Wash Cycle Table Use more detergent or change your detergent Rearrange the items so that the spray can rotate freely Clean and or fit the filter combination correctly Clean the spray arm jets See Cleaning the Spray Arms Use less detergent if you have soft water and select a shortest cycle to wash the glassware and to get them clean Use a mild abrasive cleaner to eliminate those marks Re loading the dishes properly Load the dishwasher as suggested in the directions Increase the amount of rinse aid refill the rinse aid dispenser Do not empty your dishwasher immediately after washing Open the door slightly so that the steam can escape Begin unloading the dishwasher only once t he dishes are barely warm to the touch Empty the low basket first This prevents water form dropping off dishes in the upper basket In short program
4. Electrical Connection Ensure the voltage and frequency of the power being corresponds to A Insure proper ground those onthe ing plate Only cer the ja into Het socket exists before use which is earthed properly If the electrical socket to which the appliance must be connected is not appropriate for the plug replace the socket rather than using a adaptors or the like as they could cause overheating and burns GROUNDING INSTRUCTIONS A WARNING This appliance must be earthed Inthe event Improper connection of the equipment of a malfunction or breakdown earthing will reduce the risk of electric shock by providing a path of least resistance forthe electric current This appliance is equipped with a cord having an equipment earthing conductor and an earthing plug The plug must be plugged into an appropriate outlet that is installed and earthedin accordance with all local standards and requirements grounding conductor can result in the risk of an electric shock Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded Do not modify the plug provided with the appliance If itis not fit for the outlet Have a proper outlet installed by a qualified electrician A WARNING In order to avoid that there Is more water staying in the inlet hose please close the hydrant after using For the models no safety inlet hose Cold Water Connection Connect the col
5. Turn off the water tap unload the baskets Warning wait a few minutes about 15 minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to break They will also dry better Unload the appliance starting from the lower basket Read this Manual Dear Customer Please carefully read this manual before using the dishwasher it will help you to use and maintain the dishwasher properly Keep it to refer to it at a later date Pass it on to any subsequent owner of the appliance This manual contains sections on safety Instructions Operating Instructions Installation Instructions and Troubleshooting Tips etc Before Calling for Service To review the section on troubleshooting Tips will help you to solve some common problems by yourself If you can not solve the problems by yourself please ask for the help of professional technicians NOTE The manufacturer following a policy of constant development and updating of the product may make modifications without giving prior notice 1 Safety Information eee eee eee een 1 2 NDS O S dasa saa aik naa a an aa iga Tino ao aaa 2 3 Operating Instructiongs senasa a enere aaa 3 Goriro Panel soti t to tro dets bob lo no 3 Dishwasher Features sasana aee anae aes 3 4 Prior using forthefirsttime ss araras 4 A Water Softener cc
6. after 10 seconds completely Add forgotten dishes At the End of the Wash Cycle When the working cycle has finished the buzzer of the dishwasher will sound for 8 seconds then stop Turn off the appliance using the ON OFF button shut off the water supply and open the door of the dishwasher Wait for afew minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage They will also dry better E Switch Off the Dishwasher The program has ended only if there appears a in the digital display remaining program time 1 Switch off the dishwasher by pressing the ON OFF button 2 Turn off the water tap E Open the door carefully Hot dishes are sensitive to knocks The dishes should therefore be allowed to cool down around 15 minutes before removing from the appliance Open the dishwasher s door leave it ajar and wait a few minutes before removing the dishes In this way they will be cooler and the drying will be improved E Unloading the dishwasher Itis normal that the dishwasher is wet inside Empty the lower basket first and then the upper one This will avoid water dripping from the upper Basket onto the dishes in the lower one A WARNING It is dangerous to open the door when washing because the hot water may scald you 13 Maintenance and Cleaning Filtering System The filter prevents larger remnants of food or other objects
7. beling Instruction Manual IDW604MK2 NSS van nA vr Ni HT AVS M ie TA Ss 2 q AN ti WN UAN T TA NS Mi IS ITO ET a ANN AN NE A O M Ly RS TE r TRA Z EN A Dishwasher Quick operation guide For detailed operating method read the corresponding content on the instruction manual Switch on the appliance Press the On Off button to switch on the appliance Open the door Compartment A With each wash cycle Fill the detergent dispenser Compartment B For programmes with pre wash only Follow the user instructions Mechanical indicator C Crests Cis Bile Lee Electric indicator on control panel if provided On models with water softener system only Check the regeneration Electric indicator on control panel if provided salt level lf there is no salt warning light in the control panel for some models you can estimate when to fill the salt into the softener by the number of cycles the dishwasher has run Scrape off any large amount of leftover food Soften remnants of burnt food in pans Load the baskets then load the baskets Refer to the dishwasher loading instructions Press the Programme button until the selected programme lights up Select a programme See the section entitled Operationg instruction Running the dishwasher Close the door tu
8. cap by inserting it aligned with open arrow and turning it to the closed right arrow NOTE Clean up any rinse aid spilled while during filling with an absorbent cloth to avoid excessive foaming during the next wash Don t forget to replace the cap before you close dishwasher door Adjusting Rinse Aid Dispenser Adjust lever The rinse aid dispenser has six or four settings Always start with the dispenser Rinse seton 4 If spots and poor drying are a problem increase the amount of rinse s aid dispensed by removing the dispenser lid and rotating the dial to 5 If the dishes still are not drying properly or are show spots adjust the dial to the next higher lever until your dishes are spot free The recommended setting is 4 Factory value is 4 A NOTE Increase the dose if there are drops of water or lime spots on the dishes after washing Reduce itif there are sticky whitish stains on your dishes or a bluish film on glassware or knife blades D Function of Detergent Detergents with its chemical ingredients are necessary to remove dirt crush dirt and transport it out of the dishwasher Most of the commercial quality detergents are suitable for this purpose Detergents There are 3 sorts of detergents 1 With phosphate and with chlorine 2 With phosphate and without chlorine 3 Without phosphate and without chlorine Normally new pulverised detergent is without phosphate Thus the water softener function of phosphate i
9. or harsh cleaners on any part of the dishwasher Cleaning The Door To clean the edge around the door you should use only a soft warm damp cloth To avoid penetration of water into the door lock and electrical components do not use a spray cleaner of any kind m Never use a Spray cleaner to clean the door panel as it may damage the door lock and electrical components A WARNING E Abrasive agents or some paper towels should not be used because of the risk of scratching or leaving spots on the stainless steel surface Protect Against Freezing please take frost protection measures onthe dishwasher in winter Every time after washing cycles please operate as follows 1 Cut off the electrical power to the dishwasher 2 Turn off the water supply and disconnect the water inlet pipe from the water valve 3 Drain the water from the inlet pipe and water valve Use a pan to catch the water 4 Reconnect the water inlet pipe to the water valve 5 Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump A NO TE If your dishwasher cannot work because of the ice please contact professional service persons Cleaning the Spray Arms It is necessary to clean the spray arms regularly for hard water chemicals will clog the spray arm jets and bearings To remove the spray arms screw off the nut clockwise to _ take out the washer on top of the spray arm and remove the arm Wash the arms in soapy and w
10. section entitled Salt Detergent and Rinse Aid M Insert the plug into the socket The power supply is 220 240 VAC 50 HZ the specification of the socket is 10A 250VAC Make sure that the water supply is turned on to full pressure M Press the ON OFF button and the ON OFF light or the display will turn on Press the program button to select a desired wash cycle Close the door after 10 seconds the machine will work Change the Program Premise M Acycle thatis underway can only be modified if ithas only been running fora short time Otherwise the detergent may have already been released and the appliance may have already drained the wash water If this is the case the detergent dispenser must be refilled see the section entitled Loading the Detergent M Open the door alittle to stop the washing Press the programme button more than 3 seconds to cancel the running programme Then you can select other programmes see the section entitled Starting a wash cycle M When you select Intensive Normal Eco Programmes you can select the 3in1 function 1 NOTE Ifyou open the door during a wash cycle the machine will pause When you close the door the machine will continue working after 10 seconds Forgotto Add aDish A forgotten dish can be added any time before the detergent cup opens Open the door a little to stop the washing Close the door After the spray arms stop working you can open the door The dishwasher will run
11. the soak wash cycle to drain out the water Repeat if necessary Always wipe up rinse aid spills immediately Make sure that the detergent is the one without colourant To clean the interior use a damp sponge with dishwasher detergent and wear rubber gloves Never use any other cleaner than dishwasher detergent for the risk of foaming or suds Always run the quick wash programme without any crockery in the dishwasher and without selecting the Turbo function if present after adding dishwasher salt gotten into the wash cycle The lid of the softer is loose A spray arm is Knocking against an item in a basket Items of crockery are loose in the wash cabinet This may be caused by on site installation or the cross section of the piping Check the lip Ensure the fix is fine Interrupt the programme and rearrange the items which are obstructing the spray arm Interrupt the programme and rearrange the items of crockery This has no influence on the dishwasher function if in doubt contact a suitably qualified plumber Problem The dishes are not clean Unsatis factory washing result Cloudiness on glassware Black or gray marks on dishes Detergent left in dispenser cups The dishes are not drying Unsatis factory drying result Error Codes Possible Causes The dishes were not loaded correctly The programme was not powerful enough Not enough detergent was dispensed
12. the drain hose hook to the counter __ _ Drain hose hook NOTE The top of the hose must be at a height between 40 and 100cm The free end of the hose must not be immersed in water Drain pipe MAX 1000mm e Dishwasher installation steps 1 Install the furniture door to the outer door of the dishwasher using the brackets provided Refer to the template for positioning of the brackets 2 Adjustthe tension of the door springs by using anAllen key turning in a clockwise motion totighten the left and right door springs Failure to do this could cause damage to your dishwasher Illustration 2 3 Connect the inlet hose to the cold water supply 4 Connect the drain hose Refer to diagram Figure 6 5 Connect the power cord 6 Put the dishwasher to slide rails Illustration4 7 Affix the condensation strip under the work surface of cabinet Please ensure the condensation strip is flush with edge of work surface 8 Place the dishwasher into position 9 Level the dishwasher The rear feet can be adjusted from the front of the dishwasher by turning the screws on the left and right hand side of the cabinet Illustration 6A To adjust the front feet use a wrench and turn the front feet until the dishwasher is level Illustration 6B 10 The dishwasher must be secured in place There are two ways to do this A Normal work surface secure to the work surface by using two woodscrews ensuring the dishwasher weight i
13. tip forward m When loading items to be washed 1 Locate sharp items so that they are not likely to damage the door seal 2 Warning Knives and other utensils with sharp points must be loaded in the basket with their points down or placedina horizontal position M When using your dishwasher you should prevent plastic items from coming into contact with the heating element This instruction is only applicable to machines with a visual heating element M Check that the detergent comparment is empty after completion of the wash cycle M Do not wash plastic items unless they are marked dishwasher safe or the equivalent For plastic items not so marked check the manufacturer s recommendations M Use only detergent and rinse additives designed for an automatic dishwasher M Never use soap laundry detergent or hand washing detergent in your dishwasher Keep these products out of the reach of children A WARNING M Improper connection of the eguipment grounding conductor can result in the risk of an electric shock M Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded Do not modify the plug provided with the appliance If it does not fit the outlet Have a proper outlet installed by a qualified electrician M Keep children away from detergent and rinse aid keep children away from the open door of the dishwasher there could still be some detergent left
14. 1 Warning AA ttentlon Electrical Shock Hazard The installation of the pipes Disconnect electrical power and electrical equipments before should be done by professionals installing dishwasher Failure to do so can result in death or electrical shock e Installation preparation The installation position of dishwasher should be near the existing inlet and drain hoses and power cord One side of the cabinet sink should be chosen to facilitate the connection of drain hoses of the dishwasher Note please check the accompanying installation accessories hook for aesthetic panel screw Figure l Cabinet dimensions Less than 5mm between the top of dishwasher and cabinet and the Electrical drain an outer door aligned entrances to cabinet Space between cabinet bottom and floor 600 mm Figure2 Dishwasher Minimum space when the door is opened Door of dishwasher 4 Minimum space of Aesthetic pane s dimensions and installation 1 The aesthetic wooden panel could be processed according to the Figure 3 15 Figure3 The aesthetic panel should be processed in accordance with the illustrated dimensions 680 Unit mm 2 Install the hook on the aesthetic wooden panel and put the hook into the slot of the outer door of dishwasher see figure 4a After positioning of the panel fix the panel onto the outer door by screws and bolts See figure 4b Hop hook
15. FOLLOW THIS SAFETY INFORMATION CAREFULLY KEEP THESE INSTRUCTIONS 2 Disposal Dispose of the dishwasher packaging material correctly All packaging materials can be recycled Plastic parts are marked with the standard international abbreviations m PE for polyethylene e g sheet wrapping material m PS for polystyrene e g padding material m POM polyoxymethylene e g plastic clips m PP polypropylene e g Salt filler m ABS Acrylonitrile Butadiene Styrene e g Control Panel A WARNING Packaging material could be dangerous for children For disposing of package and the appliance please goto arecycling centre Therefore cut off the power supply cable and make the door closing device unusable NM Cardboard packaging is manufactured from recycled paper and should be disposed in the waste paper collection for recycling m By ensuring this productis disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product m For more detailed information about recycling of this product please contact your local city office and your household waste disposal service DISPOSAL Do not dispose this product as unsorted municipal waste Collection of such waste separately for special treatment is necessary 3 Operation Instruction before using it for the first time Control Panel
16. ain hose The drain hose must be correctly fitted to avoid water leaks Ensure that the water drain hose is not kinked or squashed Extension Hose If you need a drain hose extension make sure to use a similar drain hose It must be no longer than 4 metres otherwise the cleaning effect of the dishwasher could be reduced Syphon Connection The waste connection must be at a height of between 40 cm minimum and 100 cm maximum from the bottom of the dish The water drain hose should be fixed by a hose clip The free end of the hose must not be immersed in water Start of Dishwasher The following things should be checked before starting the dishwasher The dishwasher is level and fixed properly The inlet valve is open There is a leakage at the connections of the conducts The wires are tightly connected The power is switched on A The inlet and drain hoses are knotted All packing materials and printings should be taken out from the dishwasher A Attention After installation please make sure to keep this manual The content of this manual is very helpful to the users 9 Troubleshooting Tips Before Calling for Service Review the charts on the following pages may save you from calling for service Technical problems General problems Noise Problem Dishwasher doesn t Start water not pumped form dishwasher Suds in the tub Stained tub interior White film on inside surface There are rust stains o
17. ainer of your machine Place the end of the funnel supplied into the hole and introduce about 1kg of salt Itis normal fora small amount of water to come out of the salt container After filling the container screw the cap tightly back clockwise Usually the salt warning light will stop being illuminated within 2 6 days after the salt container has been filled with salt Immediately after filling the salt into the salt container a washing program should be started We suggest to use the soak or rapid program Otherwise the filter system pump or other important parts of the machine may be damaged by salty water This is out of warranty A NOTE 1 The salt container must only be refilled when the salt warning light in the control panel comes on Depending on how well the salt dissolves the salt warning light may still be on even though the salt container is filled If there is no salt warning light in the control panel for some Models you can estimate when to fill the salt into the softener by the cycles that the dishwasher has run 2 If there are spills of the salt asoak or arapid program should be run to remove the excessive salt IC 00 gt uu Wel C Fill the Rinse Aid Dispenser Rinse Aid Dispenser The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes which can leave spots and streaks It also improves drying by allowing water to roll off the dishes Your dishwa
18. arm water and use a soft brush to clean the jets Replace them after rinsing them thoroughly k u 7 rr F 4 How to Keep Your Dishwasher in Shape M After Every Wash M When not in Use foraLongTime After every wash turn off the water supply to the Itis recommend that you run a wash cycle with the appliance and leave the door slightly open so that dishwasher empty andthen remove the plug from the moisture and odours are nottrapped inside socket turn off the water supply and leave the door of the appliance slightly open This will help the door M Remove the Plug seals to last longer and prevent odours from forming within the appliance Before cleaning or performing maintenance always remove the plug from the socket M Moving the Appliance E No Solvents or Abrasive Cleaning If the appliance must be moved try to keep it in the vertical position If absolutely necessary itcan be To clean the exterior and rubber parts of the dishwasher positioned on its back do not use solvents or abrasive cleaning products E Seals Only use acloth with warm soapy water To remove spots or stains from the surface of the One of the factors that cause odours to form in the interior use a cloth dampened with water ana little dishwasher is food that remains trapped in the seals vinegar ora cleaning product made specifically for Periodic cleaning with adamp sponge will prevent this dishwashers from occurring 8 Installation instruction
19. c ccecce ee eeeeeeee seen eens 4 B Loading the Salt into the Softener 5 C Fillthe Rinse Aid Dispenser es 5 D Function of Detergent ooooo novo 6 How to use the 3 in 1function ove 8 5 Loading the Dishwasher Basket 9 Attention before or after loading the Dishwasher KOS tu ka aaa SK a apang a aan ajaga gana a eee 9 Loading the upper Basket kaaranan 10 Loading the Lower Basket ooos nooo m 10 Cutlery Basket ccccc cece eee eeeee seas nn eas 11 6 Starting a washing programme 12 Wash Cycle Table sanan aaa nain aaa ata baa aga panah 12 Turning on the Appliance sae sree aranan 13 Change the Programme saene resserre 13 At the End of the Wash Cycle aaa aana 13 7 Maintenance and cleaning ooo2oooovo o 14 Filtering System ene hlad nan no ona 14 Caring for the Dishwasher o ooeo o 15 8 Installation instruction seser e eee 16 Installation preparation ss ee ee rane 16 Aesthetic pane s dimensions and installation 17 Tension adjustment of the door spring 19 Connection of drainhoses seser eens 19 Dishwasher installation steps 20 About Electricity Connecting kae eee 21 Cold Water Con
20. d sign Clark British degree Contact your local water board for information on the hardness of your water supply A NOTE if your model does not have any water softener you may skip this section WATER SOFTENER The hardness of the water varies from place to place If hard water is used in the dishwasher deposits will form on the dishes and utensils The appliance is equipped with a special softener that uses a salt container specifically designed to eliminate lime and minerals from the water B Loading the Salt Into the Softener Always use the salt intended for use with dishwasher The salt container is located beneath the lower basket and should be filled as explained in the following Attention M Only use salt specifically designed for the use in dishwashers Every other type of salt not specifically designed for the use in adishwasher especially table salt will damage the water softener In case of damages caused by the use of unsuitable salt the manufacturer does not give any warranty nor is liable for any damages caused M Only fill with salt just before starting one of the complete washing programs This will prevent any grains of salt or salty water which may have been spilled remaining on the bottom of the machine for any period of time which may cause corrosion Remove the lower basket and then unscrew and remove the cap from the salt container Before the first wash fill 1lt of water inthe salt cont
21. d water supply hose to a threaded 3 4 inch connector and make sure that it is fastened tightly in place If the water pipes are new or have not been used for an extended period of time let the water runto make sure that the water is clear This precaution is needed to avoid the riskofthe water inlet to be blocked and damage the appliance Hot Water Connection The water supply to the appliance can also be connected to the household hot water line such as central system heating system as long as itdoes not exceeda temperature of 60 In this case the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced The connection must be made to the hot water line following the same procedures as described in the section for the connection to the cold water line Positioning the Appliance Position the appliance in the desired location The back should rest against the wall behind it and the sides along the adjacent cabinets or walls The dishwasher is equipped with water supply and drain hoses that can be positioned either to the right or the left sides to facilitate proper installation How to Drain Excess Water From Hoses If the sink is 1000 higher from the floor the excess water in hoses cannot be drained directly into the sink It will be necessary to drain excess water from hoses into a bowl or suitable container that is held outside and lower than the sink Water Outlet Connect the water dr
22. eaper electricity Or just to benefit from the convenience of the programming finishing when you want to Adjustable upper basket Flexible dish loading available Adjust the upper Error alarm basket for large or awkward loads To alert you to any errors or problems with the program while it is running Salt Warning Indicator Ifthe salt is running low the warning indicator will light on the panel alerting you to topit up This Stainless steel tub ensures the best results from your machine No need to worry about staining Rinse aid Warning Indicator Broad applied voltage If the rinse aid is running low the warning indicator l will light on the panel alerting you to top it up The broad scope of the applied voltage reduce lt hig code ol electric condition This ensures the best results from your machine ellin Stoney lane prescot Merseyside L35 2XW Customer Care In case of difficulty within the UK and Northern Ireland please call the customer care help line on 0844 815 3746 This symbol on the product or in the instructions means that your electrical and electronic equipment should Be disposed at the end of its life separately from your household waste There are separate collectionsystems for recycling in the EU For more information please contact the local authority or your retailer where you purchased the product
23. ents can be easily put into the dispenser and the dispenser would not be broken 8 5 Loading the Dishwasher Baskets Recommendation M Consider buying utensils which are identified as dishwasher proof Mm Usea mild detergent that is described as kind to dishes If necessary seek further information from the detergent manufacturers m For particular items select a program with as low a temperature as possible m Toprevent damage do not take glass and cutlery out of the dishwasher immediately after the programme has ended For washing in the dishwasher the following cutlery dishes Are not suitable Are of limited suitability M Cutlery with wooden horn china or M Some types of glasses can become mother of pearl handles dull after a large number of washes M Plastic items that are not heat resistant m Older cutlery with glued parts that are not M Silver and aluminum parts have a temperature resistant tendency to discolour during washing m Bonded cutlery items or dishes M Pewter or cooper items M Glazed patterns may fade if machine m Crystal glass washed frequently M Steel items subject to rusting M Wooden platters m items made from synthetic fibres Attention before or after loading the Dishwasher Baskets For best performance of the dishwasher follow these loading guidelines Features and appearance of baskets and cutlery baskets may vary from your model Scrape off any large amounts of leftover food Soften remnan
24. ergent packaging Close the lid and press until it locks in place If the dishes are heavily soiled place an additional detergent dose in the pre wash detergent chamber This detergent will take effect during the pre wash phase A NOTE M You find information about the amount of detergent for the single programme on the last page M Please aware that according to the level soiling and the specific hardness of water differences are possible M Please observe the manufacturer s recommendations on the detergent packaging How To Use The 3IN1 Function Your dishwasher has a 3in1 function which needs no salt and rinse aid but a 3In1 tablet This dishwasher comes with a 3in1 tablet container as an accessory NOTE Only the 3in1 function for the program intensive Normal Eco Can be used with 3in1 tablets If you use 3in1 tablets in other programs the appliance will not achieve a good performance 1 The figure below shows how to hang the 3in1 tablet container on the upper basket 2 Rotate the upper sprayer and change the location of the container to ensure the upper sprayer is not obstructed by the 3in 1 tablet container Refer to the figure below for reference NY A 3 Put the 3in1 tablet Into the container then start the 3in1 program A NOTE When using 3in1 combination compact Detergents please pay attention to make sure that the size of the combination detergents fits to the dispenser so that combination deterg
25. from getting inside the pum The residues may block the filter in this case they must be removed The filter system consists of a coarse filter a flat Main filter Anda microfilter Fine filter Main filter Food and soil particles trapped in this filter are pulverizedby a special jet on the lower spray arm and washed down to drain Coarse tiite A Larger items such as pieces of bones or glass that could block the drain are trapped in the coarse filter To remove the items caught by the filter gently squeeze the tap on the top of this filter and lift out Fine filter 3 This filter holds soil and food residues in the sump area and prevents it from being redeposit on the dishes during wash cycle Filter assembly The filter efficiently removes food particles from the wash water allowing it to be recycled during the cycle For best performance and results the filter must be cleaned regularly For this reason it is a good idea to remove the larger food particles trapped in the filter after each wash cycle by rinsing the semicircular filter and cup under running water To remove the filter device pull the cup handle in the upward direction m he dishwasher must never be used without the filters A WARNING M Improper replacement of the filter may reduce the performance level of the appliance and damage dishes and utensils Van Step 1 Turn the filter in anti clockwise direction TPA
26. gent Dispenser The dispenser must be refilled before the start of each wash cycle following the instructions provided in the wash cycle table Your dishwasher uses less detergent and rinse aid than Conventional dishwasher Generally only one tablespoon of detergent is needed for a normal wash load More heavily soiled items need more detergent Always add the detergent just before starting the dishwasher otherwise it could get damp and will not dissolve properly Amount of Detergent to Use KN Detergent powder Detergent tablet A NOTE m Ifthe lid is closed press release button The lid will spring open M Always add the detergent just before starting each wash cycle NE Only use branded detergent aid for dishwasher A WARNING Dishwasher detergent is corrosive Take care to keep it out of reach of children Proper Use of Detergent Use only detergent specifically made for the use in dishwashers Keep your detergent fresh and dry Don t put powdered detergent into the dispenser until you re ready to wash dishes Fillin Detergent Fillthe detergent dispenser with detergent The marking indicates the dosing levels as illustrated on the right The place of main wash cycle detergent placed MIN means approximately 20g of detergent I The place of pre wash cycle detergent placed approximately 5g of detergent Please observe the manufacturers dosing and storage Recommendations as stated onthe det
27. inside M This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety M Children should be supervised to ensure that they do not play with the appliance M Dishwasher detergents are strongly alkaline they can be extremely dangerous if swallowed Avoid contact with skin and eyes and keep children away from the dishwasher when the door is open M The door should not be left open since this could increase the risk of tripping M lfthe supply cord is damaged it must be replaced by the manufacturer or its service agent ora similarly qualified person in order to avoid a hazard M Remove the door to the washing compartment when removing an old dishwasher from service or discarding it M Please dispose of packing materials properly M Use the dishwasher only for its intended function M During installation the power supply must not be excessively or dangerously bent or flattened Do not tamper with controls M The appliance is to be connected to the water mains using new hose sets and that old hose sets should not be reused M The maximum number of place settings to be washed is 12 M The maximum permissible inlet water pressure is 1Mpa TL NANG permissible inlet water pressure is 0 04Mpa READ AND
28. l The water softener is designed to remove minerals and salts from the water which would have a detrimental or adverse effect on the operation of the appliance The higher the content of these minerals and salts the harder your water is The softener should be adjusted according to the hardness ofthe water in your area Your local Water Authority can advise you on the hardness of the water in your area Adjusting Salt Consumption The dishwasher is designed to allow for adjustment in the amount of salt consumed based onthe hardness of the water used This is intended to optimise and customise the level o f salt consumption Please follow the steps below for adjustment in salt consumption 1 Unscrew the cap from the salt container 2 Thereis aring onthe container with an arrow on it see figure on the side if necessary rotate the ring in the anticlockwise direction from the Setting toward the sign based on the hardness of the water being used Itis recommended that adjustments should be made in accordance with the following scheme WATER HARDNESS Selector Position gt 01sumptionj Auto nomy o ena O O ZOO OKO ONO C e ms wa ws 00010108 aso 1 oor ers 1 10010180108 Note 1 abi 1 25Clarko 1 781H 0 178mmoll a 1 arke 1 0 1781mmo No salt need added DH German degree Ea Setting toward the sign Setting toward the sign fH French degree ar Setting toward between the sign an
29. min Kwh Program Intensive Eco EN 50242 For the heaviest soiled loads such as pots pans casserole dishes and dishes that have been sitting with dried food on them for a while For normally soiled loads such as pots plates glasses and lightly soiled pans standard daily cycle For lightly soiled loads such as plates glasses bowls and lightly soiled pans For dishes that need to be rinsed and dried only For lightly soiled loads such as glasses crystal and fine china A shorter wash for lightly soiled loads that do not need drying A NOTE EN 50242 This programme is the test cycle The information for comparability test Pre wash 50 U Pre wash Wash 65 U Rinse Rinse Rinse 55 U Drvino Pre wash 50 U Wash 50 U Rinse Rinse 65 U Drying Pre wash Wash 55 U Rinse 65 U Drying Wash 40 Rinse 70 U Drying Pre wash Wash 40 Rinse Rinse 60 U Drying Wash 40 C Rinse Rinse 45 U 5 25g or3in1 i 5 25g or3in1 in accordance with EN 50242 as follows M Capacity 12 setting M Position Upper basket upper wheels on rails M Rinse aid setting 6 12 Turning On the Appliance Starting a cycle wash H Draw out the lower and upper basket load the dishes and push them back It is commended to load the lower basket first then the upper one see the section entitled Loading the Dishwasher M Pour inthe detergent see the
30. n cutlery Knocking noise in the wash cabinet Rattling noise in the wash cabinet Knocking noise in the water pipes Possible Causes What To Do Fuse blown or the circuit breaker acted Power supply is not turned on Error code E1 Water pressure is low Door of dishwasher not properly closed Kink in drain hose Filter clogged Kitchen sink clogged Improper detergent Spilled rinse aid Detergent with colourant was used Hard water minerals The affected items are not corrosion resistant A programme was not run after dishwasher salt was added Traces of salt have Replace fuse or reset circuit breaker Remove any other appliances sharing the same circuit with the dishwasher Make sure the dishwasher is turned on and the door is closed securely Make sure the power cord is properly plugged into the wall socket Check that the water supply is connected properly and the water is turned on Make sure to close the door properly and latch it Check drain hose Check coarse the filter see section titled Cleaning The Filter Check the kitchen sink to make sure it is draining well If the problem is the kitchen sink not draining you may need a plumber rather than a serviceman for dishwashers Use only the special dishwasher detergent to avoid suds If this occurs open the dishwasher and let suds evaporate Add 1 gallon of cold water to the tub Close and latch the dishwasher then Start
31. nectijon eee eee neran 22 Hot Water Connection see eee eee 22 9 Troubleshooting Tips kae e vvn 23 Before calling for ServiCe aaa aaa aaa reren 23 ETOK COGS S or satia ses na Nana a 6 Ods Sb not snem 24 Technical information eee eee ewan 25 1 IMPORIANT SAFETY INFORMATION READ ALL OF THE INSTRUCTIONS BEFORE USING A WARNING When using your dishwasher follow the precautions listed below GROUNDING INSTRUCTIONS M This appliance must be grounded In the event of a malfunction or breakdown grounding will reduce the risk of anelectric shock by providing a path of least resistance of electric current This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug M he plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances WARNING PROPER USE M Do not abuse sit on or stand on the door or dish rack of the dishwasher M Do not touch the heating element during or immediately after use This instruction is only applicable to machines with a visual heating element m Do not operate your dishwasher unless all enclosure panels are properly in place Open the door very carefully if the dishwasher is operating there is a risk of water squirting out M Do not place any heavy objects on or stand on the door when it is open The appliance could
32. nt height of the rails Long items serving cutlery salad servers and knives should be placed on the shelf so that they do not obstruct the rotation of the spray arms The shelf can be folded back or be removed when not required for use d a Upperwnee H a Lower wheels Folding Spikes of Lower Basket For better stacking of pots and pans the spikes can be folded down as show in the picture right M SS JAN Cutlery Basket Cutlery should be placed in the cutlery basket with the handles at the bottom If the rack has side baskets the spoons should be loaded separately into the appropriate slots especially long utensils should be placed in the horizontal position at the front of the upper basket as shown in the picture Forks 5 Knives 2 Soup spoons 6 Serving spoons 5 Dessertspoons 7 Gravy ladles 4 Teaspoons Serving forks Do not let any item extend through bottom a A A WARNING 2M 7 el s For personal safety and a top quality cleaning place the silverware in the basket making sure that M They donot nesttogether M Silverware is placed with the handles down M But place knives and other potentially dangerous utensils are placed handles up 6 Starting a washing program Wash Cycle Table A NOTE Means need to fill rinse into the Rinse Aid Dispenser Description of Cycle Cycle Selection Detergent Running Energy Information Water Rinse pre main time
33. rn on the water tap The machine will start working after about 10 seconds 1 A running cycle can only be modified if it has been running for a short time Otherwise the detergent Changing the programme may have already been released and the water already drained If this is the case the detergent dispenser must be refilled 2 Open the door a little to stop the washing then press the Program button for more than 3 seconds to cancel the running programme 3 Select a new programme then close the door The machine will restart after about 10 seconds Hanee aaa eae a a aa e e tr em ee ee ENE SENEN eee A WARNING Add forgotten dishes in the 1 Open the door a little to stop the dishwasher i dishwasher 2 After the spray arms stop working you can open the door completely Open the door carefully 3 Add the forgotten dishes Hot steam may escape 4 Close the door the dishwasher will start running again after 10 seconds when the door is opened E f the appliance is switched If the appliance is switched off during a wash cycle when switched off during a wash cycle on again please re select the washing cycle and operate the dishwasher according to the original Power on state When the working cycle has finished the buzzer of the Switch off the appliance dishwasher will sound 8 times then stop PP Turn off the appliance using the ON OFF button
34. s not being hit by the surface Illustration 7 B Marble or granite work top secure the bracket to the side panel of the dishwasher and secure the dishwasher to the furniture housing Put the rubber cap over the screw Illustration 8 Tega a BN aa RUBBEBOVER Figure 7 20 Dishwasher must be level for proper dish rack operation and wash performance 1 Place level on door and rack track inside the tub as shown to check that the dishwasher Is level 2 level the dishwasher by adjusting the four leveling legs individually 3 When level the dishwasher please pay attention not to let the dishwasher tip over Figure 81 Check mR 3 T eee Front y Illustration of feet adjustment to Back NOTE JM The maximum adjustment pear height of the feet is 60 mm ja a ape Check level side to side About Electricity Connecting For personal safety A WARNING E DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE HE DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE EARTHING CONNECTION FROM THE POWER CORD Electrical Requirements Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate power supply Use the required fuse 10 amp time delay fuse or circuit breaker recommended and provide separate circuit serving only this appliance
35. s not given In this case we recommend to fill salt in the salt container even when the hardness of water is only 6 dH If detergents without phosphate are used in the case of hard water often white spots appear on dishes and glasses In this case please add more detergent to reach better results Detergents without chlorine do only bleach a little Strong and coloured spots will not be removed completely In this case please choose a program with a higher temperature Concentrated Detergent Based on their chemical composition detergents can be split in two basic types E conventional alkaline detergents with caustic components E low alkaline concentrated detergents with natural enzymes The use of normal washing programs in combination with concentrated detergents reduces pollution and is good for your dishes these wash programs are specifically matched to the dirt dissolving properties of the enzymes of the concentrated detergent For this reason normal wash programs in which concentrated detergents are used can achieve the same results that can otherwise only be achieved using intensive programs Detergent Tablets Detergent tablets of different brands dissolve at different speeds For this reason some detergent tablets cannot dissolve and develop their full cleaning power during short programs Therefore please use long programs when using detergent tablets to ensure the complete removal of detergent residuals Deter
36. sher is designed to use liquid rinse aids The rinse aid dispenser is located inside the door next to the detergent dispenser To fill the dispenser open the cap and pour the rinse aid into the dispenser until the level indicator turns completely black The volume ofthe rinse aid container is about 110ml Function of Rinse Aid Rinse aid is automatically added during the last rinse ensuring thorough rinsing and spot and streak free drying Attention Only use branded rinse aid for dishwasher Never fill the rinse aid dispenser with any other substances e g Dishwasher cleaning agent liquid detergent This would damage the appliance __ 5 When to Refill the Rinse Aid Dispenser If there is no rinse aid warning light in the control panel you can estimate the amount from the colour of the optical level indicator C located next to the cap When the rinse aid container is full the whole indicator will be dark As the rinse aid diminishes the size of the dark dot decreases You should never let the rinse aid level fall 1 4 full C Rinse Aid indicator As the rinse aid diminishes the size of the black dot on the rinse aidlevel indicator changes as illustrated below Full 3 4 full 1 2 full 1 4 full Should refill to eliminate spotting gt Empty To open the dispenser turn the cap tothe open left arrow and lift it out Pour the rinse aid into the dispenser being careful not to overfill Replace the
37. t and then the upper basket M The Method Loading Normal Dishware Loading the Upper Basket The upper basket is designed to hold more delicate and lighter dishware such as glasses coffee and tea cups and saucers as well as plates small bowls and shallow pans as long as they are not too dirty Position the dishes and cookware so that they will not get moved by the spray of water Cups 2 Small serving bowl 5S Large serving bowl Glasses S Saucers 6 Dish 7 may 17 Dessert dishes TAN wes T P i Loading the Lower Basket We suggest that you place large items and the most difficult to clean items are to be placed into the lower basket such as pots pans lids serving dishes and bowls as shown in the figure below Itis preferable to place serving dishes and lids on the side of the racks in order to avoid blocking the rotation of the top spray arm Please be reminded that Pots serving bowls etc must always be placed top down Deep pots should be slanted to allow water to flow out The Bottom Basket features folding spikes so that larger or more pots and pans can be loaded EREE 7 Dessert dishes Oval platter G Dinner plates O Soup plates n Silverware basket Adjusting the Upper Basket The height of the upper basket can be adjusted in order to create more space for large utensils both for the upper lower basket The height of the upper basket can be adjusted by placing the wheels on differe
38. the washing temperature is lower This also lowers cleaning performance Choose a program with a long washing time Water drainage is more difficult with these items Cutlery or dishes of this type are not suitable for washing in the dishwasher When some malfunctions come on the appliance will display error codes to warn you Codes Meanings Possible Causes Tap is not opened or water intake is restricted or water pressure is too low Longer inlet time M Overfilled Too much inlet water m f overflow occurs turn off the main water supply before calling a service A WARNING m f there is water in the base pan because of an overfill or small leak the water should be removed before restarting the dishwasher 24 Technical Information A 9 sA A IA a A V 07005 A CA Gea D 4 Vig ime N Dy SSA m U 2 d A WAU F A A a ga ws KN SS INN a ae nS DISHWASHER FEATURES Additional features of this dishwasher are Overflow protection gt wash programs Your dishwasher has an overfill protection You can choose desired program according to the program which automatically shuts off the soiled level inlet valve and starts the drain pump if the water is overflowing l 8 place settings Time delay feature Be sufficient for normal use This allows the start of the programme to be delay between 1 and 24 hours enabling you to benefit fully from ch
39. then lift it up SA 4 a ff AN LEZ Ee I p _ a Step 2 lift the Main filter up Step 3 lift the Fine filter up NOTE When following this procedure from stepi to step 3 the filter system will be removed when following it from Step 3 to Step 1 the filter system will be installed 14 Remarks Inspect the filters for blocking after every time the dishwasher has been used By unscrewing the coarse filter you can remove the filter system Remove any foodremnants and clean the filters under running water A NOTE The entire filter assembly should be cleaned once a week Cleaning the Filter To clean the coarse filter and the fine filter use a cleaning brush Reassemble the filter parts as shown in the figures on the last page and reinsert the entire assembly in the dishwasher positioning itin its seat and pressing downwards When cleaning the filters don t knock on them Otherwise the filters could be A WARNING contorted and the performance of the dishwasher could be decreased Caring for the Dishwasher The control panel can be cleaned by using a lightly dampened cloth After cleaning make sure to dry it thoroughly For the exterior use agood appliance polish wax Never use sharp objects scouring pads
40. ts of burnt food in pans It is not necessary to rinse the dishes under running water Place objects in the dishwasher in following way 1 Items such as cups glasses pots pans etc are faced downwards 2 Curved items or ones with recesses should be loaded aslant so that water can run off 3 All utensils are stacked securely and can not tip over 4 All utensils are placed in the way that the spray arms can rotate freely during washing A NOTE Very smallitems should not be washed in the dishwasher as they could easily fall out of the basket m Load hollow items such as cups glasses pans etc With the opening facing downwards so that water cannot collect in the container or a deep base Dishes and items of cutlery must not lie inside one another or cover each other To avoid damage to glasses they must not touch Load large items which are most difficult to clean into the lower basket The upper basket is designed to hold more delicate and lighter dishware such as glasses coffee andtea cups Long bladed knives stored in an upright position are a potential hazard Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket Please do not overload your dishwasher This is important for good results and for reasonable consumption of energy Removing the Dishes To prevent water dripping from the upper basket into the lower basket we recommend that you empty the lower basket firs
Download Pdf Manuals
Related Search
Related Contents
RECHARGEABLE HAND TORCH LAH 55 A1 Iniciar sesión - CAE - Bolsa de Trabajo Monitor di sicurezza AS-interface Canada - Buyandsell.gc.ca IB-HXP930_Trance Plus Copyright © All rights reserved.
Failed to retrieve file