Spektrum SPMAR7350
Contents
1. want to continue If you select Continue you must re program all of your travel values dual rates etc Port Assignment The Port Assignment screen enables you to change the receiver port assignment for each surface lt PORT ASSIGNMENT e ASSIGNMENT AUX CHANNELS er GEAR CAUTION Changing the port assignments may cause issues with other control surfaces or mixes that you have programmed in your or AUX 1 6 AUX 2 AUX 3 transmitter Always perform a control test and set failsafe values before flying your aircraft Failure to do so may result in the aircraft crashing e Gray port assignemnts are not in use AUX 4 m e Orange port assignments are currently in use MIXES e Red port assignments are currently being used as part of a No Mix Found mix SPEKTRUM 7 Model Reset Resets the active model in the application Model Reset Are you sure you want to reset the model to default settings Share Via Email Attaches the active model file to a new email The email recipient can open the attachment in the AS3X Programmer app Expo Positive Expo decreases control stick sensitivity near center Negative Expo increases control stick sensitivity near center Swipe left or right to change between Roll Pitch and Yaw Select a flight mode to access the Expo curve N Drag the curve UP or DOWN to adjust the Expo values Directions can be adjusted at the s2. L FM1 RATE GAIN 0 HEADING GAIN 0 PRIORITY RL LO PRIORITY 100 Name Master Slave Rate Offset Output The Dashboard screen enables you to see all of the gain dual rate and expo settings for each Flight Mode You can also adjust the values by selecting any of the value boxes DASHBOARD New Model 0 FLIGHT MODE 1 ROLL PITCH YAW o 0 DASHBOARD New Model 0 FLIGHT MODE 2 ROLL PITCH YAW 0 o 0 DASHBOARD New Model 0 FLIGHT MODE 3 ROLL PITCH YAW 0 0 0 0 0 d e ro WS ye WS m pl In ini An PRIORITY 100 100 100 D R 100 100 100 100 100 100 Eo 0 0 e Dashboard Dashboard Dashboard Country of Purchase Horizon Hobby Contact Information Address Horizon Service Center servicecenter horizonhobby com Request Repairs and Repair Requests Form www quickbase com db Horizon Product Support er bghj ey8c a GenNewRecord Product Technical Assistance Heli 888 959 2304 Air 888 959 2305 sales horizonhobby com Sales Heli 888 959 2304 Air 888 959 2305 Nn Service Parts Sales sales horizonhobby co uk United Kingdom a Horizon Hobby Limited 44 0 1279 641 097 Horizon Technischer Service Germany sales Horizon Hobby GmbH ua Service Parts Sales Horizon Hobby SAS Service Parts Sales China Horizon Hobby China 4105 Fieldstone Rd United States of America Champaign Illinois 61822 USA Units 1 4 Ployters Rd Staple Tye 0 Ha
3. SPERT RUT Instruction Manual Bedienungsanleitung Manuel d utilisation Manuale di Istruzioni To get more information including details on downloading the Spektrum AS3X Mobile Programming Application visit www spektrumRC com AS3xX or scan this QR code Minimum system requirements iOS 6 0 iPhone 4 iPod 4th gen and Android 4 0 Transmitter Setup Connecting to the Receiver e Set all transmitter settings to 1 Connect the servo plug on the default Mit dD i audio interface cable to the BIND Important The Aileron Elevator PROG port on your receiver and Rudder settings in the Power the receiver through any transmitter must remain at their Sui open channel factory default values Settings for DAT MIL BE RESET 4GHz DSMX VAN si E 6CH SPORT RECEIVER 5 gt DP Confirm Reset BOCK gt 9 Model 1 p reverse sub trim travel adjustment ne 3 Connect the audio plug on the expo and dual rate must be done in interface cable to the audio jack the App only on your mobile device The volume MUST be turned up to full 4 Ensure you have secure receiver data port and audio data port connections lt gt Installing the Receiver If the receiver is being connected _____________________ ___ for the first time the App will 1 Install the receiver in one of 8 automatically open in Model Wizard il using double in the Model Setup screen 2 The servo ports must be facing the front or
4. ame time or independently To adjust directions at the same time make sure both directions are orange Active Direction is orange Inactive Direction is gray A Press the lt to return to the main Expo screen Dual Rate Dual Rate is a percentage of the Travel value 1 Swipe left or right to change between Roll Pitch and Yaw 2 Select a flight mode to access the Dual Rate curve 3 Drag the curve UP or DOWN to adjust the Dual Rate values e Directions can be adjusted at the same time or independently To adjust directions at the same time make sure both directions are orange Active Direction is orange Inactive Direction is gray 4 Press the lt to return to the main Dual Rate screen DUAL RATE DUAL RATE Blue o oT Ke o aE eee LEFT 0 RIGHT 0 DUAL RATE LEFT 100 RIGHT 100 SPEKTRUM Gain amp Priority Gain is a percentage of the Travel value 1 Swipe left or right to change between Roll Pitch and Yaw 2 Select a flight mode to access the Gain curve 3 Drag the curve to adjust the Gain values e Directions can be adjusted at the same time or independently To adjust directions at the same time make sure both directions are orange Active Direction is orange Inactive Direction is gray ABS Absolute When ABS is selected the Rate and Heading Gain values that are programmed in the Application are fixed absolute for each given flight mode and are not adjustable from the t
5. e You have the option of selecting Preset or Hold for each receiver port If you aren t sure what each port does tap the lt to return to the Port Assignment screen Surface Setup Tap each surface to access the following e Servo Reverse e Sub Trim e Travel e Balance Servo Reverse If the surface moves in the wrong direction when you move the control stick on the transmitter tap the selector to reverse the direction SPEKTRUM lt PORT ASSIGNMENT lt a lt PORT ASSIGNMENT gt Q ni SURFACE SETUP AILERON SO REVERSE D SUBTRIM Sub Trim 1 Tap SUBTRIM to access the sub trim value 2 Tap the or to change the sub trim value Tapping moves the trim to the Left and moves the trim to the Right 3 Tap SUBTRIM again to save the value Travel 1 Tap TRAVEL to access the travel adjust graph 2 To adjust the travel values drag up or down on the vertical line to adjust the Left Right values simultaneously e Directions can be adjusted at the same time or independently To adjust directions at the same time make sure both directions are orange Active Direction is orange Inactive Direction is gray Balance The balance function is a 7 point curve used to prevent binding when multiple servos are used on a single control surface To adjust the balance on a control surface drag each of the 7 points on the curve until the control surface moves without binding Press
6. lt to return to the Wizard lt PORT ASSIGNMENT LEFT lt A TRAVEL AILERON 100 RIGHT SUBTRIM 0 BALANCE AILERON SURFACE SETUP AILERON SO REVERSE QD SUBTRIM 100 SPEKTRUM Exit the Wizard Surface Setup is the last step in the Wizard Press the LJ in the upper right corner to save settings and exit the Wizard The application will display the AS3X Settings menu after exiting the Wizard Initial Setup Sal HT i Expo Dual Rate Gain amp Mixing About Priority Initial Setup The Initial Setup menu enables you to view individual screens without using aa INITIAL SETUP the Wizard You will also use the Initial Setup menu to perform a Model Reset n share model files via e mail or access the Wizard Some screens in the Initial Setup menu also have programming capabilities that are not available in the Wizard a a Receiver Flight Mode Flight Mode Switch Orientation Switch Select the transmitter channel you wish to use for the Flight Mode switch a Tip If you wish to use the Gear channel for flight modes but also wish AN to use a 3 position switch you will need to assign the Gear channel to a ai 3 position switch in the transmitter Setu Fail Safe Port Model Assigment sb Reset Wing Type IMPORTANT If you select Aircraft Type in the Initial Setup menu the following pop up alert appears Reselecting your aircraft type will reset all your surface settings Are you sure you
7. optional 2 Name the Model 3 Select the receiver that you want to program If a receiver is already bound and connected to the mobile device the app will auto detect the receiver 4 Select your transmitter Model Setup vv Done Select Transmitter Cancel Model Name New Model 0 gt Receiver AR 636 6335 gt Transmitter DX9 gt SPEKTRUM 3 Receiver orientation Tell the app how the receiver is mounted in your aircraft 1 To flip the receiver horizontally swipe LEFT or RIGHT 2 To flip the receiver vertically swipe UP or DOWN The servo pins must always point toward the nose or tail of the aircraft Flight Mode Setup Select the transmitter channel you want to use for flight modes Wing Type 1 Swipe left or right across the wing to change the wing type 2 Swipe left or right across the tail to change the tail type If a tail type is not available it is because you have run out of channels in the receiver 4 ORIENTATION b gt lt ORIENTATION 7 RECEIVER ORIENTATION RECEIVER ORIENTATION Swipe RIGHT or LEFT Swipe UP or DOWN FLIGHT MODE gt FM Channel Assignment FM CHANNEL GEAR AUX 1 AUX 2 AUX 3 UNASSIGNED 74 AIRCRAFT TYPE le WING NORMAL TAIL NORMAL SPEKTRUM Port Assignment The port assignment screen shows you where to connect the servos to the receiver No options are available on this screen it is only used for reference Failsaf
8. ransmitter REL Relative When REL is selected the Rate and Heading gain values are adjustable from the transmitter This allows in flight gain adjustments Some Spektrum transmitters feature an AS3X screen that allows the gain to be adjusted from the transmitter and displays the active value for each gain that includes priority in real time IMPORTANT When REL is selected the gain value in the application represents the maximum available gain 1 Drag up or down in the black area of the curve to adjust the Rate Gain 2 Drag up or down on the vertical line to adjust the Heading Gain Heading Gain is only active when the transmitter control stick is near center 3 Drag left or right across the vertical line to adjust the Stick Priority Adjusting the Priority enables you to turn the gain off when the transmitter control stick reaches a certain position 4 Press the El to return to the Gain screen Mixing The Mixing menu in the AS3X Programmer App is only used for mixes involving control surfaces Any mixes involving lights retracts etc should be programmed in your transmitter as usual Six programmable mixes are available in the app 1 Press the to create a new mix 2 Assign the master and slave channels 3 Assign mix values 4 Press the sync button to save the mix and send the programming to the receiver You must send the mix programming to the receiver before you can create another mix SPEKTRUM ROL
9. rear of the aircraft 3 The receiver must be mounted parallel to the roll pitch and yaw axis NOT ANGLED AS3X Programming Cable AR636 shown Binding mu Insert the bind plug into in the receiver bind port and power on the receiver The LED should blink to indicate the receiver is in bind mode Bind the transmitter to the receiver AR636 shown at low throttle Refer to your transmitter s manual for details Does not apply to iOS Devices Plug servo leads into assigned ports Typical Servo Port Assignments Normal Model Type Delta Port 1 Throttle RENON Male IYNE N on how to bind to your specific e Port 2 Aileron e Port 1 Throttle transmitter PA SAGE BSE e Port 3 Elevator e Port 2 Right Bort 4 Rudd Aileron e Port 4 Rudder e Port 3 Left Port 5 Gear Flap Aileron Port 6 Left e Port 4 Rudder Aileron if equipped with Port 5 Gear dual servos e Port 6 Aux 1 S A AR636 shown for reference Port assignments E nb will be similar for all AS3X receivers Refer to your RR receivers manual for more information 2 SPEKTROM 1 lt and GI move to the next or previous screen in the Wizard 2 The CD appears at the end of the Wizard Tap the square to save the airplane configuration and to exit the Wizard Model Setup The Wizard starts automatically when you open the app for the first time Model Setup 1 Select a photo for the model
10. rlow Essex CM18 7NS United Kingdom service horizonhobby de Christian Junge StraBe 1 49 0 4121 2655 100 25337 Elmshorn Germany infofrance horizonhobby com 33 0 1 60 18 34 90 l info horizonhobby com cn l 86 021 5180 9868 11 Rue Georges Charpak 71127 Lieusaint France Room 506 No 97 Changshou Rd shanghai China 200060 2014 Horizon Hobby LLC DSM DSM2 DSMX the DSMX logo AS3X and the Horizon Hobby logo are registered trademarks of Horizon Hobby LLC The Spektrum trademark is used with permission of Bachmann Industries Inc Apple is a trademark of Apple Inc registered in the U S and other countries Android and Google are trademarks or registered trademarks of Google Inc All other trademarks service marks and logos are property of their respective owners Created 07 2014 42221 10 SPEKTRUM
Download Pdf Manuals
Related Search