Sencor SVC 1011BL FORTE vacuum cleaner
Contents
1. Accessory holder Stopper for the vertical parking position Stopper for the horizontal parking position Safety lock Hose end CD Bag full indicator 2 Horizontal parking position 38 Power cord EN 5 Copyright O 2012 Fast CR a s Revision 05 2012 Vacuum Cleaner SVC 1010 1011BL 1011GR Forte C D Front wheel mechanism 2 Vertical parking position Suction of the motor serves as protection against burning the motor in the case that the vacuum tube becomes blocked ASSEMBLY Inserting the hose into the air suction hole on the vacuum cleaner Press the safety button on the hose end and insert the hose end into the air suction hole on the vacuum cleaner until you hear click The hose is now secured in the correct position Attach the holder to the telescopic tube Make sure to place the holder with the hose on the wider part of the telescopic tube Attach the floor inlet nozzle to the telescopic tube Make sure to install the floor nozzle on the narrower part of the telescopic tube Adjust the length of the telescopic tube Adjust the length of the telescopic tube as follows Move and hold the button on the tube forward as shown the by arrows and adjust the length of the tube as required Then release the safety lock and move the tube slightly forward until you hear a click The telescopic tube is now securely set in position USING2. YOUR VACUUM CLEANER Connecting your vacuum cleaner to power source wall outlet Pull the plug of the supply cable from the vacuum cleaner until the desired length of the cable is out of the appliance Insert the plug into the socket Caution The yellow marking on the power cord tells you that the cord is close to its end Do not pull the cord further than the red marking Adjusting the floor inlet nozzle according to the floor surface You can set the inlet nozzle according to the floor surface by adjusting the inlet flap e f you want to vacuum carpets close the bristles of the inlet inside the inlet nozzle by turning the flap accordingly e f you want to vacuum hard and smooth surfaces move the bristles out of the nozzle by turning the flap accordingly Copyright O 2012 Fast CR a s Revision 05 2012 Vacuum Cleaner SVC 1010 1011BL 1011GR Forte Turning your vacuum cleaner on and off To switch your machine on or off press the START STOP button on the vacuum cleaner body Adjusting the suction strength The suction strength may be adjusted by moving the rider on the vacuum cleaner body small range or by the moveable rider on the hose handler vy Tip Q e Use the maximum suction strength when vacuuming carpets or floors with a hard surface Use the reduced strength when vacuuming upholstery window curtains etc e If the hose holder becomes blocked when vacuuming disconnect it from the telescopic tube and al
3. indicates that this product shall not be treated as household waste Please dispose of this product at your applicable collection point for the recycling of electrical amp electronic equipment waste Alternatively in some states of the European Union or other European states you may return your products to your local retailer when buying an equivalent new product The correct disposal of this product will help save valuable natural resources and help in preventing the potential negative impact on the environment and human health which could be caused as a result of improper liquidation of waste Please ask your local authorities or the nearest waste collection centre for further details The improper disposal of this type of waste may fall subject to national regulations for fines For business entities in the European Union If you wish to dispose of an electrical or electronic device request the necessary information from your seller or supplier Disposal in other countries outside the European Union If you wish to dispose of this product request the necessary information about the correct disposal method from local government departments or from your seller C This product meets all the basic EU regulation requirements that relate to it Changes to the text design and technical specifications may occur without prior notice and we reserve the right to make these changes EN 13 Copyright O 2012 Fast CR a s Revision 05 2012 V
4. MATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS 13 DISPOSAL Or USED ELECTRICAL AND ELECTRONIC APPLIANCES cocos 294 Cte e e n es 13 EN 2 Copyright O 2012 Fast CR a s Revision 05 2012 Vacuum Cleaner SVC 1010 1011BL 1011GR Forte IMPORTANT SAFETY NOTICE 1 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Carefully unpack the product and take care not to throw away any part of the packaging material before you have found all parts of the product This product may not be used by any persons including children with mental disabilities weak strength or by inexperienced persons unless they have been properly trained or schooled in the safe use of the product or unless they are properly supervised by a qualified person who is responsible for their safety Children must be supervised to ensure that they do not play with the product Before connecting this product to the socket outlet make sure the voltage stated on the label of the product corresponds to the voltage in your wall socket Never use the accessories not supplied with this product or not designed for use with this product Do not place the electric cord near hot surfaces or over sharp objects Do not place heavy objects on the power cable Position the cable so that it will not be stepped on or tripped over Make sure the power cord is not touching a hot surface If the pr
5. Vacuum Cleaner User s manual 9 2 1 Y e 2 SENCOR SVC 1010 1011BL 1011GR Forte Before first use please read all instructions contained in this user manual carefully even if you are already familiar with using similar products Only use this product in accordance with the instructions described in the user manual Keep the user manual in a safe place for future use Save the original packaging material warranty card and proof of purchase receipt at least for the duration of the warranty policy If you need to ship this product back pack it in the original cardboard box to ensure maximum protection during shipping or transport e g when moving or when you need to send this product for repair EN 1 Copyright O 2012 Fast CR a s Revision 05 2012 Vacuum Cleaner SVC 1010 1011BL 1011GR Forte CONTENTS IMPORTANT ARE NOTE co s a A un dE SE qm RE ded ER ROV V k b RAR 2 DESCRIPTION tas aterra ad at NV e DER o O O E 00 a ee na k n 5 ASSEMBLY xro O E ES A A KR Ad 3 Per sata 6 USING YOUR VACUUM CLEANER IIT 6 USING YOUR ACCESSORIES a atas obno n d odd edad unes ie dd dedo dada do DERE b t suda STORAGE OF VACUUM CLEANER upad a o ion doe do e dnd dici sudo dete dete ae mme 8 CLEANING AND MAINTENANCE ui actrice Cg ERI a Rame Ra S e bed Eoo dee K en 8 TROUBLE SHOOTING O T oe ee O O O oe ee 12 PECI APE CP OS e v D dob eek eh abad rka Cede t Robur IHRE odes 12 INSTRUCTIONS AND INFOR
6. acuum Cleaner SVC 1010 1011BL 1011GR Forte NOTES EN 14 Copyright 2012 Fast R a s Revision 05 2012
7. h your other hand to protect the vacuum cleaner input area from damage MN Tip Q If the winding process stops and part of the power cord is still outside release the winding button and pull the cable out again by about 50cm and press the winding button again and repeat the winding process Carrying your vacuum cleaner If you need to carry the vacuum cleaner hold it only by the handle Caution Never try to carry your vacuum cleaner by holding the dust container handle STORAGE OF VACUUM CLEANER Before storage you can disassemble your appliance to each individual part or you can store it assembled with the telescopic tube stored in one of the parking positions CLEANING AND MAINTENANCE Caution Before cleaning disconnect this product from the power source Emptying the dust container Empty the dust container as soon as the full container warning light comes on otherwise the air flow and the suction strength will be reduced Safety lock of the bottom hatch Plastic conical filter Bottom hatch Copyright O 2012 Fast CR a s Revision 05 2012 Vacuum Cleaner SVC 1010 1011BL 1011GR Forte F D Plastic conical filter 1 Press the safety lock and pull the container handle up to remove the dust container from the vacuum cleaner 2 Place the dust container above a waste bin 3 Press the safety notch on the dust container and the bottom of the container will open 4 Byturning in the anti cl
8. he hose is bent or damaged in any way Do not move over the power cord with the vacuum cleaner Never use the vacuum cleaner without the protective motor filter the output filter the dust container or the HEPA filter Do not place the vacuuming hose inlet nozzle or vacuuming accessories near to your eyes or ears EN 3 Copyright O 2012 Fast CR a s Revision 05 2012 Vacuum Cleaner SVC 1010 1011BL 1011GR Forte 30 Vacuuming of some types of floors or floor tiles can create a static electricity charge which is not dangerous for the user The manufacturer is not responsible for damages caused by incorrect use of this appliance or its accessories Such damages include food spoilage injuries burns scalding fire etc Copyright O 2012 Fast CR a s Revision 05 2012 Vacuum Cleaner SVC 1010 1011BL 1011GR Forte DESCRIPTION A D START STOP button Safety lock for the dust container Dust container handle 4 Vacuuming hose connection hole 5 Vacuum cleaner handle 6 Motor power output control Cover of the input micro filter Cable winding button 9 Wheel with rubber rim Dust container Handle 43 Sliding knob for air suction 3 Telescopic tube Safety lock for the telescopic tube 9 Floor inlet nozzle Flap position for vacuuming carpets 2 Flap position for vacuuming hard smooth floors Hose AOA
9. inge for the H E P A filter Foam pre filter H E P A filter 1 Press the safety lock and pull the container handle up to remove the dust container from the vacuum cleaner 2 By pressing the safety lock on the plastic frame of the H E P A filter remove it from the dust container and from behind it also remove the foam pre filter 3 Wash both filters under running lukewarm water or if necessary replace with new ones 4 Then first insert the foam pre filter and afterwards the H E P A filter 5 First insert the H E P A filter with two lugs into the hinges in the dust container and close it until the safety lock clicks into position 6 Place the dust container back into the vacuum cleaner Caution Never place the filters back into the vacuum cleaner if they are wet or damp Always wait until they are thoroughly dry The dust container is equipped with a safety lock see pic H which if the H E PA filter is not present will prevent the insertion of the dust container into the vacuum cleaner Changing the outlet filter Inflow micro filter Cover for the inflow micro filter Cover lock Cover lock EN 10 Copyright O 2012 Fast CR a s Revision 05 2012 Vacuum Cleaner SVC 1010 1011BL 1011GR Forte Cover of the outflow micro filter Guide lug outflow micro filter 1 First remove the grill of the inflow filter by pulling upwa
10. ockwise direction remove the plastic conical filter from the container tip out the dust and if necessary wash under running lukewarm water 5 In the same way tip out the dust and dirt from the container into standard household waste If the container is heavily soiled you may wash the entire container under lukewarm running water However before doing SO it is necessary to remove the H E P A filter and its foam pre filter from the container 6 Then insert the plastic conical filter back into the dust container and lock by turning in the clockwise direction 7 Close the bottom lid of the container Make sure the safety lock button is engaged 8 Place the dust container back into the vacuum cleaner Caution Before replacing the dust container and the plastic conical filter back into the vacuum cleaner make sure that all parts are completely dry Changing and cleaning the H E P A filter and the foam pre filter H E P A filter Lug for the hinge of the dust container Safety lock for the H E P A filter Lug for the hinge of the dust container Copyright O 2012 Fast CR a s Revision 05 2012 Vacuum Cleaner SVC 1010 1011BL 1011GR Forte Safety lock Hinge for the H E P A filter H
11. oduct s power cord is damaged have an authorised service or qualified person replace it in order to prevent hazards It is forbidden to use the product if it has a damaged electric cord or electric cord plug Do not disconnect the electrical plug from the wall outlet by pulling on the cord Under no circumstances should you repair or alter the product yourself as this may cause injury by electric shock Entrust all repairs and adjustments to a specialised company service Tampering with the product during the guarantee period may invalidate the guarantee Never touch or use the product if you have wet hands or feet Store and use the product away from flammable or volatile materials and solutions This appliance is designed for household use Do not use in industrial surroundings or outdoors Do not use the product for any other purposes than those intended Do not spray the product with water or any other liquid Do not pour water or any other liquids into the product Do not submerge the product in water or in any other liquid Make sure the product does not come in contact with water Never use the product near a bathtub wash basin or any other container filled with water If you are not using your machine disconnect the power cord from the socket If the product is not used turn it off and disconnect the supply cable from the wall outlet Prior to cleaning proceed in the same manner Never leave the product switched on without supe
12. orrect position Filter is clogged Clean the filter Cord is not fully wound up While winding the cord might While winding up hold the cord have become dislodged from the slightly tensioned winding wheel and try again a qualified technician desired damaged a qualified technician position TECHNICAL SPECIFICATIONS Voltage A o o Y 230 V AC Misura d a HQ 50 Hz SUCHOKOUU el E O M 300W Rated Power IDE esce AO E o a O E eeu 1400 W put ste TR TE e e db een bactoamnee T E i REE 1600 W Safety class with regard to electric shock protection 0 0 2 ne eee I NOBE EVE ss o r a o fate ah lt 73 dB A Power cordlength ps noua 5m Operational range IP Da a ao Tao a 15m Dust container capacity o a 1 6l Dimensions length x width x height 360 x 265 x 255mm A O O O OE O L O O RO O 4 4kg The declared noise emission level for this appliance is lt 73 dB A which represents level A of the acoustic power relative to the reference acoustic power of 1 pW Amendments to text and technical parameters are reserved EN 12 Copyright 2012 Fast R a s Revision 05 2012 Vacuum Cleaner SVC 1010 1011BL 1011GR Forte INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS Dispose of packaging material at a public waste disposal site DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES The meaning of the symbol on the product its accessory or packaging
13. rds in the place of both safety locks 2 Then remove the outflow filter and replace with a new one 3 Insert the new output filter back into the vacuum cleaner so that the lug fits into the slit for the filter in the vacuum cleaner and cover with the grill first insert the grill in the backward direction and then click in both safety locks Caution Insert the ouflow filter into the vacuum cleaner with the plastic grill facing out Cleaning your vacuum cleaner To clean the outer parts of the product use a soft cloth dipped in lukewarm water Do not use aggressive cleaning agents paint thinners or solvents Using these solutions could damage the surface of the product EN 11 Copyright O 2012 Fast CR a s Revision 05 2012 Vacuum Cleaner SVC 1010 1011BL 1011GR Forte TROUBLESHOOTING Before you decide to contact an authorized service centre please read these following tips in the troubleshooting chart Problem Possible cause Recommended action Motor does not turn on Power cord is not firmly inserted Insert the power plug firmly into into the mains power socket the mains power socket Mains power socket is damaged Check the mains power socket The vacuum cleaner is not Turn on the product switched on Suction power is weak The product is clogged Remove the clogged material The dust filter needs to be Clean the dust filter cleaned The dust container is not in the Close the dust container c
14. rvision In order to avoid deformation or a fire in the plastic components of the vacuum cleaner do not expose the vacuum to direct sunlight do not place it close to heaters open fires or other sources of heat and do not leave the vacuum cleaner operating for too long if the air input is blocked Do not use the product in an environment with excessive dust Use extra care if the product is used near children Always place the product out of their reach If the product is being used do not block its air input and output openings Blocked air vents may cause overheating and motor damage Vacuuming objects mentioned below may damage your product or cause injuries to the operating person e wet floors water or other liquids e any type of sharp objects such as broken glass or ceramics needles pins etc e burning cigarettes or smouldering pieces matches or any other flammable or volatile liquids e g gasoline paint thinners etc e flour cement plaster i e dust from holes drilled in walls In order to avoid damage to furniture or injuries to persons hold the power cord in your hands as it winds up Do not vacuum large pieces of paper or plastic bags They may easily clog the pipe or hose If the product becomes clogged for any reason turn it off by removing it from the electric socket and clean the pipe or hose In order to avoid damage to the hose do not step on it or forcefully bend it Do not use the vacuum cleaner if t
15. so disconnect the hose from the vacuum cleaner body Then place the holder inside the suction hole on the vacuum cleaner body and vacuum the stuck dirt out Temporary interruption of the vacuuming process If you want to stop vacuuming for a short time you may use one of the parking positions e for the horizontal parking position use the lug at the end of the floor nozzle e for the vertical parking position use the lug on the telescopic tube Caution Do not move the vacuum cleaner from place to place if the hose is in the parked position It may break or the lugs for the floor nozzle or telescopic tube may break off USING YOUR ACCESSORIES Slot nozzle for vacuuming in hard to reach places e g windows corners book shelves areas between mattresses upholstery etc Upholstery nozzle Brush nozzle by turning the brush part it is possible to use it for vacuuming hard to reach places Tip If during vacuuming you use an accessory very often you may attach it to the special holder on the telescopic tube EN 7 Copyright O 2012 Fast CR a s Revision 05 2012 Vacuum Cleaner SVC 1010 1011BL 1011GR Forte Ending the vacuuming process When you finish vacuuming switch the vacuum cleaner off by pressing the START STOP button and then disconnect the supply cable plug from the socket To wind the power cord back to the vacuum cleaner press and hold the winding button with one hand Hold the cord wit
Download Pdf Manuals
Related Search