E-flite UMX Beast 3D BNF
Contents
1. When the fuselage must be opened for access to servos or receiver first cut the tape or decals before opening the canopy hatch Removing tape or decals may remove paint from the fuselage Troubleshooting Guide AS3X Problem Possible Cause Solution Control surfaces are Control surfaces may not have been Center control surfaces mechanically by not at neutral position mechanically centered from factory adjusitng the U bends on control linkages ee Aircraft was moved after the flight battery Disconnect flight battery and reconnect while was connected and before sensors being sure model does not move for 5 seconds initialized Model flies incon Trims are moved too far from neutral Neutralize trims and mechanically adjust sistently from flight position linkages to center control surfaces to flight Problem Possible Cause Solution Aircraft will not Throttle stick and or throttle trim too high Reset controls with throttle stick and throttle respond to throttle trim at lowest setting m SE Throttle channel is reversed Reverse throttle channel on transmitter connected to the receiver Flight battery damaged Replace flight battery and follow flight battery instructions Flight conditions may be too cold Make sure battery is warm before use Battery capacity too low for flight conditions Replace battery or use a larger capacity battery LED on receiver Transmitter too near aircraft during binding Power off transmitter move tra2. BNF BASIC UMM BEAST 3D Instruction Manual Bedienungsanleitung Manuel d utilisation Manuale di Istruzioni MY Eflfe ADVANCING ELECTRIC FLIGHT NOTIGE All instructions warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby Inc For up to date product literature visit www horizonhobby com and click on the support tab for this product Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product NOTICE Procedures which if not properly followed create a possibility of physical property damage AND little or no possibility of injury CAUTION Procedures which if not properly followed create the probability of physical property damage AND a possibility of serious injury WARNING Procedures which if not properly followed create the probability of property damage collateral damage and serious injury OR create a high probability of superficial injury AN WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result in damage to the product personal property and cause serious injury This is a sophisticated hobby product It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate this pro
3. ESC Lower throttle and throttle Install flight battery and CP Keep plane immobile trim to lowest settings connect it to the ESC on its wheels away from Power on the Transmitter wind for five seconds then wait 5 seconds gd Series of tones Continuous LED If you accidentally connect the battery while the throttle is fully raised the ESC will enter programming mode Disconnect the battery immediately The AS3X system will not activate until the throttle stick or trim is increased for the first time Once the AS3X is active the control surfaces may move rapidly on the aircraft This is normal AS3X will remain active until the battery is disconnected CAUTION Always keep hands away from the propeller When armed the motor will turn the propeller in response to any throttle movement Control Direction Test You should bind your aircraft and transmitter before doing these tests Move the controls on the transmitter to make sure the aircraft control surfaces move correctly and in the proper direction Make sure all linkages move freely and that paint or decals are not adhered to them Control Centering Before first flights or in the event of an accident 2 When needed use a pair of pliers to carefully make sure the flight control surfaces are centered bend the metal of the control linkage see Adjust linkages mechanically if the control surfaces illustration are not centered 3 Make the U shape narrower to make the Fo
4. helicopters The AS3X System invisibly helps with complicated corrections Low Voltage Cutoff LVC When a Li Po battery is discharged below 3V per cell it will not hold a charge The Beast 3D ESC protects the flight battery from over discharge using Low Voltage Cutoff LVC Before the battery charge decreases too much LVC removes power supplied to the motor Power to the motor quickly decreases and increases showing that some battery power is reserved for flight control and safe landing When the motor power pulses land the aircraft immediately and recharge the flight battery Disconnect and remove the Li Po battery from the aircraft after use to prevent trickle discharge Before storage charge the Li Po battery to full capacity allowing you to experience ultra smooth flight performance that feels so natural that you ll quickly build confidence in the capability of the airplane AS3X system setup is easy Just bind your DSM2 DSMX transmitter to the model using a basic airplane program and AS3X will assure that the locked in feel and control authority you want is instantly at your command to help show off your RC pilot skills AS3X will innovate the way you ll want to fly now and in the future To see what we mean go to www E fliteRC com AS3X During storage make sure the battery charge does not fall below 3V per cell Tip Due to the quiet nature of the aircraft you may not hear the pulsing of the motor Fo
5. liability is asserted As Horizon has no control over use setup final assembly modification or misuse no liability shall be assumed nor accepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting liability If you as the pur chaser or user are not prepared to accept the liability associated with the use of the Product purchaser is advised to return the Product immediately in new and unused condition to the place of purchase Law These terms are governed by Illinois law without regard to conflict of law principals This warranty gives you specific legal rights and you may also have other rights which vary from state to state Horizon reserves the right to change or modify this warranty at any time without notice Warranty Services Questions Assistance and Services Your local hobby store and or place of purchase cannot provide mwarranty support or service Once assembly setup or use of the Product has been started you must contact your local distributor or Horizon directly This will enable Horizon to better answer your questions and ervice you in the event that you may need any assistance For questions or assistance please direct your email to productsupport horizonhobby com or call 877 504 0233 toll free to speak to a Product Support representative You may also find information on our website at www horizonhobby com Inspection or Services If this Product nee
6. K UK AC to 12V DC 1 5 Amp AC to 12V DC 1 5 Alimentation secteur AC to 12V DC 1 5 EFLC4000AU Power Supply AU Amp Power Supply 12V DC 1 5A AU Alimentatore AU AU EFLCAQ00EU AC to 12V DC 1 5 Amp AC to 12V DC 1 5 Alimentation secteur AC to 12V DC 1 5 Power Supply EU Amp Netzgerat EU 12V DC 1 5A EU Alimentatore EU DX4e DSMX Spektrum DX4e 4 Emetteur DX4e DSMX DX4e DSMX SPMR4400 4 Channel Transmitter Kanal Sender ohne 4 voies Mode 2 4 Trasmettitore 4 canali Mode 2 4 Empfanger MD 2 4 Mode 2 4 DX4e DSMX Spektrum DX4e 4 Emetteur DX4e DSMX DX4e DSMX SPMR44001 4 Channel Full Range Kanal Sender ohne 4 voies Mode 1 3 Trasmettitore 4 canali Transmitter Mode 1 3 Empfanger MD 1 3 Mode 1 3 DX5e DSMX Spektrum DX5E Emetteur DX5e DSMX DX5e DSMX 5 channel Transmitter DSMX 5 Kanalsender 5 voies Mode 2 Trasmettitore 5 canali SPMR5510 Mode 2 ohne Empfanger Mode 2 MD 2 DX5e DSMX Spektrum DX5E Emetteur DX5e DSMX DX5e DSMX 5 channel Transmitter DSMX 5 Kanalsender 5 voies Mode 1 Trasmettitore 5 canali SPMR55101 S Mode 1 ohne Empf nger Mode 1 MD 1 SPMR6610 DX6i DSMX 6 Channel DX6i DSMX 6 Kanal Emetteur DX6i DSMX DX6i DSMX Trasmet Transmitter Mode 2 Sender Mode 2 6 voies Mode 2 titore 6 canali Mode 2 SPMR66101 DX6i DSMX 6 Channel DX6i DSMX 6 kanal Emetteur DX6i DSMX DX6i DSMX Trasmet Transmitter Mode 1 Sender Mode 1 6 voies Mode 1 titore 6 canali Mode 1 DX6i DSMX 6 Channel Spektrum DX6i Emetteur DX6i DSMX DX6
7. Recharge flight battery Service of Power Components Disassembly AN CAUTION DO NOT handle propeller parts while the flight battery is connected Personal injury could result Propeller 1 Remove the battery hatch by gripping the front of the hatch then pulling it up and away from the fuselage 2 Carefully loosen screw A inside the spinner then remove the propeller assembly B from the motor shaft C 3 Remove the spinner D and glue from the backplate E to free the propeller F and backplate The motor magnet may attract screws to the motor Motor and Firewall 1 Remove 2 screws G the firewall H and motor from the fuselage motor mount J 2 Remove the top screw K from the firewall H and motor 3 Disconnect the motor wire connector from the ESC receiver connector Assembly Motor and Firewall 1 Connect the motor wire connector to the ESC receiver connector so the wire colors align 2 Install the motor in the firewall using a screw in the top of the firewall 3 Attach the firewall to the fuselage motor mount using 2 screws Propeller 1 Install the backplate and propeller on the motor shaft using a screw The numbers on the propeller must face out from the fuselage for correct propeller operation 2 Install the spinner on the propeller and backplate using foam compatible CA 3 Putthe foam battery hatch on the fuselage and slide it back to fully engage the fuselage
8. S3X Receiver BL ESC BL180 Brushless Outrunner Motor 2500Kv Ac B i 4 2 3 g Performance Linear Long Throw Servo Needed to Complete Battery 180mAh 25 20C Li Po CEL Battery Charger 2S 7 4V Li Po WWI Recommended Transmitter Ll Spektrum DSM2 DSMX full range OO with dual rates DX4e and up H 15 7 in 400mm a y 2 0 oz 58 g To register your product online go to www e fliterc com Preflight Ghecklist v EE 1 Charge flight battery 2 Install flight battery in the aircraft once it has been fully charged EN 3 Bind aircraft to your transmitter _ 4 Make sure linkages move freely v E 6 Adjust flight controls and transmitter ES 7 Perform a radio system Range Check a 8 Find a safe and open area mM 9 Plan flight for flying field conditions 5 Perform Control Direction Test with the transmitter AS3X Stabilization DELIVERS BREAKTHROUGH PERFORMANCE The AS3X System for airplanes is an electronic enhancement system that makes it possible for you to experience super smooth flight performance yet still have full control authority for sport scale or 3D flight Turbulence torque and tip stalls are just some of the many complications to assess when trying to achieve smooth flight The Horizon Hobby world class team of RC pilots developed the AS3X System for airplanes based on the successful use of AS3X with ultra micro flybarless
9. UMX Beast 3D Beast 3D Beast 3D Beast 3D Part Nummer Num ro Codice Firewall UMX Beast Brandschott UMX Support moteur UMX Ordinata UMX Beast EFLU4066 Beast Beast EFLUA067 Prop Adaptor Prop Adaptor Adaptateur d h lice Adattatore elica UMX Beast UMX Beast UMX Beast UMX Beast EFLUC1007 Celectra 2S 7 4V DC Celectra 2S 7 4V DC Chargeur CelectraDC Celectra 25 7 4V DC Li Po Charger Li Po Ladegerat 7 4V 28 Caricabatterie Li Po Power Cord for AnschluBstecker mit Cable d alimentation Cavo alimentazione per EFLUC1008 EFLUC1007 Krokodilklemmen fur EFLUC1007 EFLUC1007 EFLUC1007 FFLUA061 Carbon Rods Set E flite UMK Beast Set de biellettes Set aste in carbonio UMX Beast Anlenkungen Carbon carbone UMX Beast UMX Beast EFLUA046 Pushrod Set Gestange Set UMK Set de tringleries Set rinvii UMX Beast Beast UMX Beast UMX Beast Description Beschreibung Description Descrizione DSM 6 Ch Ultra DSM2 6 Kanal Ultra micro r cepteur DSM2 6 Ch Ultra EFLUA864 Micro AS3X Ultra Micro AS3X 6voies DSM2 AS3Xa Micro AS3X Ricevitore Receiver BL ESC Empf nger BL ESC avec contr leur brush BL ESC less int gr 2 3 Gram Perfor 2 3 Gramm Servo 2 3g lin aire Ottimo servo lineare mance Linear Long Hochleistungs longue course per a corsa lunga da 2 3 SPMSA2030L Throw Servo Linear Servo mit formant Grammi langem Ruderweg Replacement Servo Austausch Servo M canique de rem Meccanica ricambio SPM6836 Mechanics Ultra Mechanik U
10. a Horizon Product Support S ee 877 504 0233 All other products 61 E A productsupport horizonhobby com Units 1 4 Ployters Rd Staple Tye United Kingdom Horizon Hobby Limited Harlow Essex CM18 7NS United Kingdom Christian Junge Stra e 1 Germany Horizon Technischer 25337 Elmshorn 49 0 4121 2655 100 Service service horizonhobby de Germany 14 Rue Gustave Eiffel France Horizon Hobby SAS Zone d Activit du R veil Matin Mus Ae Monde infofrance horizonhobby com 91230 Montgeron Compliance Information for the European Union Declaration of Conformity in accordance with ISO IEC 17050 1 No HH2011093005 44 0 1279 641 097 sales horizonhobby co uk Product s UMX Beast 3D BNF Basic Item Number s EFLU4850 Equipment class The object of declaration described above is in conformity with the requirements of the specifications listed below following the provisions of the European R amp TTE directive 1999 5 EC EN 301 489 1 V1 7 1 2006 EN 301 489 17 V1 3 2 2008 C a ym O LK Steven A Hall Vice President Signed for and on behalf of International Operations and Risk Management Horizon Hobby Inc i Champaign IL USA Horizon Hobby Inc Sep 30 2011 Instructions for disposal of WEEE by users in the European Union This product must not be disposed of with other waste Instead it is the user s responsibility to dispose of their waste equipment by handing it over to a designated collections point fo
11. ds to be inspected or serviced please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization RMA number Pack the Product securely using a shipping carton Please note that original boxes may be included but are not designed to withstand the rigors of shipping without additional protection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon is not responsible for merchandise until it arrives and is accepted at our facility An Online Service Request is available at www horizonhobby com under the Support tab If you do not have internet access please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service When calling Horizon you will be asked to provide your complete name street address email address and phone number where you can be reached during business hours When sending product into Horizon please include your RMA number a list of the included items and a brief sum mary of the problem A copy of your original sales receipt must be included for warranty consideration Be sure your name address and RMA number are clearly written on the outside of the shipping carton Notice Do not ship LiPo batteries to Horizon If you have any issue with a LiPo battery please contact the appropriate Horizon Product Support office Warranty Require
12. duct in a safe and responsible manner could result in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision Do not attempt disassembly use with incompatible components or augment product in any way without the approval of Horizon Hobby Inc This manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or serious injury Age Recommendation Not for children under 14 years This is not a toy Designed by aerobatic world champion Quique Somenzini the Ultra Micro extreme UMX Beast 3D BNF Basic is a thrilling small scale recreation of one of the most awe inspiring airplanes ever created At its heart is the revolutionary AS3X System built in to help provide you with a true 3D experience the ability to fly indoors and handle windy conditions outdoors The added punch of its stronger 2500Kv 180BL outrunner motor delivers an outstanding thrust to weight ratio But beyond the capability to better perform all out 3D you will find that the Beast 3D with AS3X gives you unmatched precision in its size class and remarkably stable handling Surprisingly all of the performance possible from the UMX Beast 3D BNF Basic only requires basic radio programming And even though your new model is fully assemb
13. i DSMX Trasmet SPMR6610E Transmitter Mode DSM X Sender ohne 6 voies Mode 2 EU titore 6 canali Mode 2 EU Empfanger MD2 2 EU DX6i DSMX 6 Channel Spektrum DX6i Emetteur DX6i D5MX DX6i DSMX Trasmet SPMR66101E Transmitter Mode DSMX Sender ohne 6 voies Mode 1 EU titore 6 canalir Mode 1 EU Empfanger MD1 1 EU 96 Part e Nummer sone mm ar Num ro Codice Description Beschreibung Description Descrizione DX7s DSMX Spektrum DX7s Emetteur DX7s DSMX DX7s DSMX SPM7800 7 Channel Transmitter 7 Kanal Sender 7 voies Mode 2 Trasmettitore 7 canali Mode 2 Mode 2 DX7s DSMX Spektrum DX7s Emetteur DX7s DSMX DX7s DSMX SPM7800EU 7 Channel Transmitter 7 Kanal Sender 7 voies Mode 2 EU Trasmettitore 7 canali Mode 2 EU Mode 2 EU DX7s DSMX DX7s DSMX Emetteur DX7s DSMX DX7s DSMX SPM78001AU 7 Channel Transmitter 7 Channel Transmit 7 voies Mode 1 AU Trasmettitore 7 canali Mode 1 AU ter Mode 1 AU Mode 1 AU DX7s DSMX Spektrum DX7s Emetteur DX7s DSMX DX7s DSMX SPM78001EU 7 Channel Transmitter 7 Kanal Sender 7 voies Mode 1 EU Trasmettitore 7 canali Mode 1 EU Mode 1 EU Mode 1 EU SPMR8800 DX8 DSMX Transmitter Spektrum DX8 nur Emetteur DX8 DSMX DX8 DSMX Solo Only Mode 2 Sender Mode 1 4 8 voies Mode 2 trasmettitore Mode 2 DX8 DSMX Transmitter Spektrum DX8 nur Emetteur DX8 DSMK DX8 DSMX Solo SPMR8800EU Only Mode 2 EU Sender Mode 1 4 8 voies Mode 2 EU trasmettitore Mode 2 EU DX8 DSMX Transmit
14. itch instructions 7 After five to 10 seconds the receiver status LED will become solid indicating that the receiver is bound to the transmitter If the LED does not turn solid refer to Troubleshooting Guide at back of manual For subsequent flights power on the transmitter for 5 seconds before connecting the flight battery Installing the Flight Battery 1 Remove the battery hatch from the nose of the aircraft 2 Attach the flight battery to the hook and loop strip A on the battery tray See the Adjusting the Center of Gravity instructions for the battery s position 3 Place the aircraft on the ground out of the wind and connect a fully charged flight battery Ensure the aircraft is immobile for 5 seconds so the AS3X system initializes correctly See the Arming the ESC instructions for correct connection of the battery to the ESC 4 Install the battery hatch NOTICE If using a different battery than the recommended 2 Cell 7 4V 180mAh 206 Li Po you will need to apply a circle of hook and loop fastener to the back of the battery opposite the side with the label in order to hold the battery in place AN CAUTION Always disconnect the Li Po battery from the aircraft receiver when not flying to avoid over discharging the battery Batteries discharged to a voltage lower than the lowest approved voltage may become damaged resulting in loss of performance and potential fire when batteries are charged Arming the
15. led please read and follow this manual completely to be sure you re ready to take full advantage of what this awesome RC aircraft has to offer Table of Contents Specifications nen nen ananane 3 Flying Tips and Repairs 8 Preflight Eet 4 Additional Safety Precautions and Warnings 9 AS3X SEHR Eet 4 Service of Power Components 10 Low Voltage Cutoff LVO 4 Troubleshooting Guide 11 Transmitter and Receiver Binding 5 Troubleshooting Guide Continued 12 Installing the Flight Battery D Warranty and Repair Policy 13 Arming th ESG asasih eaaa aa an aka ah alian D Warranty and Service Information 14 Control Direction Test 6 Compliance Information for the European Union 14 Control Centering errereen 6 Parts Contact Information 54 Settings for Control Horns 7 Replacement Parts sss 54 Dual Rates EE 7 Optional Replacement Parts 55 Adjusting Center of Gravity CG 7 Specifications I 14 7 in 372mm J Installed gt EFLU4864 DSM2 6Ch Ultra Micro A
16. ltra Micro placement pour servo per servo Ultra Micro Micro Long Throw Long Throw Ultra micro longue Long Throw course Replacement Servo Ersatz Stellringe Colliers de servo Collari di fissaggio per EFLU4070 Retaining Collars MCX MSR MCX 2 MSR servo MCX 2 MSR MCX 2 MSR Interplane Strut Set Tragflachenstreben Set de haubans UMX Set montanti alari UMX EFLU4069 UMX Beast Beast Beast 55 Optional Parts and Accessories Optionale Bauteile und Zubehorteile Pi ces optionnelles et accessoires Parti opzionali e accessori Part e Nummer ech SED an Num ro lt Codice Description Beschreibung Description Descrizione EFLA7OQUM Charger Plug Adapter Ladekabel Adapter Prise d adaptation Adattatore per la EFL EFL chargeur EFL carica EFL EFLA7001UM Charger Plug Adapter Ladekabel Adapter TP Prise d ana RES per la TP chargeur TP carica TP EFLU4068 Harness Adapter UMX E flite UMX Beast Adaptateur de Cavo adattatore UMX Beast Y Kabel c blage UMK Beast Beast AS2000 Servo E flite UMX Beast AS2000 Inverseur de AS2000 Inversore per SPM6825 Reverser Y Kabel Servo Servo AC to 12V DC 1 5 Amp AC to 12V DC 1 5 Alimentation secteur AC to 12V DC 1 5 ELFC4000 Power Supply US Amp Power Supply 12V DC 1 5A US Alimentatore US US AC to 12V DC 1 5 Amp AC to 12V DC 1 5 Alimentation secteur AC to 12V DC 1 5 EFLC4000UK Power Supply UK Amp Power Supply 12V DC 1 5A UK Alimentatore U
17. ments For Warranty consideration you must include your original sales receipt verifying the proof of purchase date Provided warranty conditions have been met your Product will be serviced or replaced free of charge Service or replacement decisions are at the sole discretion of Horizon Non Warranty Service Should your service not be covered by warranty service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50 of the retail purchase cost By submitting the item for service you are agreeing to payment of the service without notification Service estimates are available upon request You must include this request with your item submitted for service Non warranty service estimates will be billed a minimum of VG hour of labor In addition you will be billed for return freight Horizon accepts money orders and cashiers checks as well as Visa MasterCard American Express and Discover cards By submitting any item to Horizon for service you are agreeing to Horizon s Terms and Conditions found on our website www horizonhobby com Service Requestl 13 Warranty and Service Information Country of Horizon Hobby Address Phone Number Email Address Purchase 4105 Fieldstone Rd 877 504 0233 Horizon Service Center f e T Electronics and engines Champaign Illinois Online Repair Request visit United States 61822 USA www horizonhobby com service of Americ
18. n dealer OTHER THAN THE EXPRESS WARRANTY ABOVE HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRAN TIES OF NON INFRINGEMENT MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIRE MENTS OF THE PURCHASER S INTENDED USE Purchaser s Remedy Horizon s sole obligation and purchaser s sole and exclusive remedy shall be that Horizon will at its option either i service or ii replace any Product determined by Horizon to be defective Horizon reserves the right to inspect any and all Product s involved in a warranty claim Service or replacement decisions are at the sole discretion of Horizon Proof of purchase is required for all warranty claims SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER S SOLE AND EXCLUSIVE REMEDY Limitation of Liabili HORIZON SHALL NOT BE LIABLE FOR SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT WARRANTY TORT NEGLIGENCE STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Further in no event shall the liability of Horizon exceed the individual price of the Product on which
19. nsmitter a larger flashes and aircraft process distance from aircraft disconnect and reconn will not bind to ect flight battery to aircraft and follow binding transmitter during instructions binding Bind switch or button not held long enough Power off transmitter and repeat bind process during bind process Hold transmitter bind button or switch until receiver is bound LED on receiver Less than a 5 second wait between first Leave transmitter on disconnect and reconnect flashes rapidly and powering on transmitter and connecting flight battery to aircraft aircraft will not flight battery to aircraft respond to transmit ter after binding Aircraft bound to different model memory Select correct model memory on transmitter ModelMatch radios only and disconnect and reconnect flight battery to aircraft Flight battery transmitter battery charge is Replace recharge batteries too low 11 Troubleshooting Guide Gontinued Problem Possible Cause Solution Control surface does Control surface control horn linkage or Replace or repair damaged parts and adjust not move servo damage controls Wire damaged or connections loose Check wires and connections connect or replace as needed Flight battery charge is low Fully recharge flight battery Control linkage does not move freely Make sure control linkage moves freely Controls reversed Transmitter settings reversed Perform Control Direction Test and adjust controls on transmi
20. nstreben Cabane UMX Beast Cabana UMX Beast EFLU4064 UMX Beast 3D EFLUA858 Fuselage Set UMX Rumpf UMX Beast Fuselage UMK Beast Set fusoliera UMK Beast 3D 3D 3D Beast 3D EFLUA860 Tail Surface set Leitwerksset UMX Empennage UMX Set piani di coda UMX UMX Beast 3D Beast 3D Beast 3D Beast 3D EFLUA854 Wheel Pants Set Radschuhe UMX Chapeaux de roues Set carenatura ruote UMX Beast 3D Beast 3D UMX Beast 3D UMX Beast 3D EFLUA055 Landing Gear with Fahrwerk mit Radern Chapeaux de roues Carrello con ruote Wheels UMK Beast UMK Beast 3D UMX Beast UMX Beast EFL U4862 Battery Hatch UMX Akkuklappe UMX Capot UMK Beast 3D Coperchio batteria 86 Beast 3D Beast 3D UMK Beast 3D EFLUA865 Decal Set UMX Dekorb gen UMX Planche de d coration Set adesivi UMX Beast Beast 3D Beast 3D UMX Beast 3D 3D EFLUA863 Canopy hatch UMK Kabinenhaube UMX Verri re UMX Beast Coperchio capottina Beast 3D Beast 3D 3D UMX Beast 3D EFLUPO503 5x2 75 Electric pro 5 x 2 75 UMK Beast 5x2 75 H lice lec Elica 5x2 75 UMX peller UMX Beast trique UMX Beast Beast BL180 Brushless BL180 Brushless BL180 Brushless BL180 motore brush EFLUM180BL2 Outrunner Motor AuBenlaufer Motor acage tournante less a cassa rotante 2500Kv 2500Kv 2500Kv 2500Kv FFLUBA 802520 180mAh 2S AN 180mAh 2S 7 4V 180mAh 2S 7 4V 20C 180mAh 2S 7 4V 20C 20C Li Po 26AWG 20C Li Po Akku Li Po 26AWG Li Po 26AWG EFLUA851 Spinner UMX Spinner UMX C ne UMX Ogiva
21. r Current Protection Bessmeemsueamm mem location to fly your aircraft OCP This feature protects propeller strike the ESC from overheating OCP stops the motor when the transmitter throttle is set too high and the propeller cannot turn The OCP will only activate when the throttle stick is positioned just above 1 2 throttle After the ESC stops the motor fully lower the throttle to re arm the ESC NOTICE Crash damage is not covered under warranty Repairs Repair the Beast 3D using foam compatible CA cyanocrylate adhesive or clear tape Only use foam compatible CA as other types of glue can damage the foam When parts are not repairable see the Replacement Parts List for ordering by item number Place the Beast 3D in position for takeoff facing into the wind if flying outdoors Set dual rates to low position and gradually increase the throttle to 34 to For a listing of all replacement and optional parts refer to the list at the back of this manual full and steer with the rudder Pull back gently on NOTICE Use of foam compatible CA accelerant the elevator and climb to check trim Once the trim on your model can damage paint DO NOT handle is adjusted begin exploring the flight envelope of model until accelerant fully dries the Beast 3D Additional Safety Precautions and Warnings As the user of this product you are solely responsible for operating ina manner that does not endanger yourself and others or re
22. r best performance with AS3X it is important that connector shorter Make the U shape wider excessive trim is not used If the model requires to make the linkage longer excessive trim adjust the linkages and return the trim on the transmitter to neutral position Use of the transmitter sub trims will not correctly center the aircraft control surfaces due to the mechanical limits of the linear servos 1 Make sure the control surfaces are neutral when the transmitter controls and trims are centered The transmitter sub trim must be set to zero Settings for Gontrol Horns The following illustrations show linkage positions chosen for the most balanced aerobatic response Linkage connections on the control horns directly affect aircraft response CAUTION Extreme 3D flying is for advanced modelers Using this setting without proper experience could result in loss of control of your aircraft and a crash causing damage to the aircraft and personal injury Dual Rates We recommend using a DSM radio capable of dual rates due to the aerobatic capabilities of the Beast 3D The settings below are recommended starting settings Adjust according to individual preferences after the initial flight High Rate Low Rate Adjusting Center of Gravity CG The CG location is 19mm back from the leading edge of the bottom wing at the root This CG location has been determined with the 2S 180mAh 7 4V Li Po battery installed with the f
23. r the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural E sources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or where you purchased the product Parts Gontact Information Intaktinformationen fur Ersatzteile Coordonn s pour obtenir de pieces d tach es Recapiti per i ricambi Country of Purchase Horizon Hobby Address Phone Number Email Address Units 1 4 Ployters Rd Staple Tye 44 0 1279 641 097 Harlow Essex sales horizonhobby co uk CM18 7NS United Kingdom Christian Junge StraBe 1 25337 49 0 4121 2655 100 Horizon Hobby GmbH Elmshorn Germany service horizonhobby de 14 Rue Gustave Eiffel 33 0 1 60 47 44 70 France Horizon Hobby SAS Zone d Activit du R veil Matin ii 0 91230 Montgeron infofrance horizonhobby com Replacement Parts Ersatzteile Pieces de rechange Ricambi United Kingdom Horizon Hobby Limited Part e Nummer qe ER Num ro Codice Description Beschreibung Description Descrizione Wing Set UMX Tragflachenset UMX Aile UMK Beast 3D Set ala UMX Beast 3D EFLU4859 Beast 3D Beast 3D Cabane UMX Beast Tragflache
24. r your first flights set your transmitter timer or a stopwatch to five minutes Adjust your timer for longer or shorter flights once you have flown the model NOTICE Repeated flying to LVC will damage the battery Transmitter and Receiver Binding Binding is the process of programming the receiver of the control unit to recognize the GUID Globally Unique Identifier code of a single specific transmitter You need to bind your chosen Spektrum DSM2 DSMX 9 technology equipped aircraft transmitter to the receiver for proper operation Any JR or Spektrum DSM2 DSMX transmitter can bind to the EFLUA864 receiver Due to the aerobatic Capabilities of the UMX Beast 3D it is highly recommended that you use a transmitter with dual rates Please visit www bindnfly com for a complete list of compatible transmitters NOTICE When using a Futaba transmitter with a Spektrum DSM module reversing the throttle channel is required v Binding Procedure 1 Refer to your transmitter s unique instructions for binding to a receiver 2 Make sure the flight battery is disconnected from the aircraft 3 Power off your transmitter 4 Connect the flight battery in the aircraft The receiver LED will begin to flash rapidly Typically after 5 seconds 5 Make sure transmitter controls are neutral and throttle and throttle trim are in low position E 6 Put your transmitter into bind mode Refer to your transmitters manual for binding button or sw
25. ront edge of the battery aligned or slightly forward of the rear edge of the cowl INTERMEDIATE 3D FLYING MM EXTREME 3D FLYING Fe Aileron Elevator Rudder may gt NOTIGE DO NOT SET YOUR TRANSMITTER TRAVEL ADJUST OVER 100 If the TRAVEL ADJUST is set over 100 it will not result in more control movement it will overdrive the servo and cause damage It is normal for linear servos to make noise Noise is not an indication of a faulty servo The oversized battery tray allows for Center of Gravity adjustment Start by placing the front edge of the battery aligned with or slightly forward of the rear edge of the cowl Adjust as needed by sliding the battery back or forward The wire length provides for either front facing or rear facing battery connection Flying Tips and Repairs Flying Failure to lower the throttle stick and trim to the lowest possible positions during a crash could result in damage to the ESC in the receiver unit which may require AWARNING While the Beast 3D may be flown indoors in an open space such as a gymnasium we recommend flying your Beast 3D outside in no greater than moderate winds Always avoid flying near houses trees wires and buildings You should also be careful to avoid flying in areas where there are many people replacement such as busy parks schoolyards or soccer fields The Beast 3D is equipped NE Consult local laws and ordinances before choosing a with Ove
26. sult in damage to the product or the property of others e Always keep a safe distance in all directions around your model to avoid collisions or injury e Always operate your model in open spaces away from full size vehicles traffic and people e Always carefully follow the directions and warnings for this and any optional support equipment chargers rechargeable battery packs etc e Always keep all chemicals small parts and anything electrical out of the reach of children Post m Checklist 1 Disconnect flight battery from ESC Required for Safety and battery life 3 Remove flight battery from aircraft This model is controlled by a radio signal subject to interference from many sources outside your control This interference can cause momentary loss of control so it is advisable to always keep a safe distance in all directions around your model as this space will help avoid collisions or injury e Always avoid water exposure to all equipment not specifically designed and protected for this purpose Moisture causes damage to electronics e Never place any portion of the model in your mouth as it could cause serious injury or even death e Never operate your model with low transmitter batteries 5 Store flight battery apart from aircraft and monitor the battery charge flight plan results planning for future flights m 6 Make note of flight conditions and EN 2 Power off transmitter NC my 4
27. ter DX8 DSMX Transmit Emetteur DX8 DSMX DX8 DSMX Solo SPMR88001AU Only Mode 1 AU ter Only Mode 1 AU 8 voies Mode 1 trasmettitore Mode 1 AU DX8 DSMX Transmitter DX8 DSMX Transmit Emetteur DX8 DSMX DX8 DSMX Solo SPMR88001EU Only Mode 1 EU ter Only Mode 1 EU 8 voies Mode 1 EU trasmettitore Mode 1 EU All Spektrum DX8 transmitters can be set up for modes 1 4 Alle Spektrum DX8 Sender konnen f r Mode 1 4 eingestellt werden Tous les metteurs Spektrum DX8 peuvent tres param tr s dans les 4 modes Tutti i trasmettitori Spektrum DX8 possono essere configurati per i modi 1 4 57 2012 Horizon Hobby Inc E flite AS3X UMK JR Celectra DSM2 DSMX and ModelMatch are trademarks or registered trademarks of Horizon Hobby Inc The Spektrum trademark is used with permission of Bachmann Industries Inc Beast and its design are either registered trademarks or trademarks of Kevin Kimball used under license to Horizon Hobby Inc The trim scheme of the Beast was designed by Mirco Pecorari of Aircraft Studio Design Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan US D578 146 PRC ZL 200720069025 2 US 7 898 130 Other patents pending www e fliterc com Elite ADVANCING ELECTRIC FLIGHT Created 06 12 33095 2
28. tter appropriately Motor loses power Damage to motor or power components Check motor and power components for damage replace as needed Motor power quickly Battery power is down to the point of Recharge flight battery or replace battery that decreases and receiver ESC Low Voltage Cutoff LVC is no longer performing increases then motor loses power Motor ESC is not Over Current Protection OCP stops the Fully lower throttle and throttle trim to arm ESC armed after landing motor when the transmitter throttle is set high and the propeller cannot turn Servo locks or freezes Travel adjust value is set above 100 Set Travel adjust to 10096 or less and or set at full travel overdriving the servo sub trims to Zero and adjust linkages mechanically 12 Warranty and Repair Policy What this Warranty Govers Horizon Hobby Inc Horizon warrants to the original purchaser that the product purchased the Product will be free from defects in materials and workmanship at the date of purchase What is Not Covered This warranty is not transferable and does not cover i cosmetic damage ii damage due to acts of God accident misuse abuse negligence commercial use or due to improper use installation operation or maintenance iii modification of or to any part of the Product iv attempted service by anyone other than a Horizon Hobby authorized service center or v Products not purchased from an authorized Horizo
Download Pdf Manuals
Related Search