AG Neovo C-17P LED display
Contents
1. Safety Information This FCC Class B compliant digital device complies with the Interference Causing C Equipment Regulations of Canada FCC Declaimers This device complies with Section 15 of the FCC listing The operation procedures must meet the following conditions 1 this device must not cause any damaging interference and 2 this device must accept any received interference including any unpredictable interference that may possibly occur Dear users This device has passed the Class B digital device regulations and complies with Section 15 of the FCC listing these are intended to provide reasonable warranty against damaging interference for home use This device will produce use and emit radio frequency energy therefore installation or use without following the instructions given may cause damaging interference to radio communication Nonetheless it is not possible to state with certainty that interference will occur from specific installations If this device has caused damaging interference to radio or TV signals simply turn the device on and off to check if such interference is caused by the device we recommend that you fix the interference using the following methods e Readjust the direction or location of the antenna e Increase the distance between this device and the receiver e Use a different povver source other than the povver source used by the receiver e Consult your local dealer or an experienced r2. Move the OSD up and down on the screen OSD Timer Adjust OSD display time setting Transparency Adjust OSD Transparency ones Select PC GAME MOVIE display mode Audio Volume Adjust the Audio Volume gt Select D SUB signal or DVI signal Select the DCR Mode on or off Reset CR Restore to factory settings C 17P 1000 1 typical Sync Frequency Horizontal 30kHz 80kHz ea Display Mode 31 469 59 940 21175 IJ o VGA 640 x 480 37 861 72 809 37 500 75 000 31 500 35 156 SVGA 800 x 600 Li 48 077 46 875 XGA 1024 x 768 56 476 60 023 Ae EE 60 020 108 000 79 976 75 025 135 000 Display Mode Hori sync kHz Vert sync Hz Pixel Clock MHZz Sync Polarity H V 4
3. adiol TV technician Making changes or modifications to the device vvithout the permission from an authorized dealer may void the vvarranty of this device VVarning VVEEE Information for users applicable in European Union countries The symbol on the product or its packaging signifies that this product has to be disposed separately from ordinary household vvastes at its end of life Please kindly be avvare that this is your responsibility to dispose electronic equipment at recycling centers so as to help conserve natural resources Each country in the European Union should have its collection centers for electrical and electronic equipment recycling For information about your recycling drop off area please contact your local related electrical and electronic equipment vvaste management authority or the retailer where you bought the product Important Safety Instruction 1 Read these instructions thoroughly and keep this user manual for future use 2 Do not use the product near water Never spill liquid of any kind of the products Clean LED monitor when power off Never clean it with liquid cleanness or liquefier Better use clean wet cloth carefully 3 Do not place the product on an unstable cart stand or table Doing so may cause the product to fall which can seriously damage it 4 To ensure reliable operation never block these ventilation slots by placing the product on a bed rug or similar surface this product s
4. display products including LED may have this kind of image stagnation and this is not a kind of defect In order to avoid the phenomenon of image stagnation we suggest that the screen protection program be set when your PC or system is spare 1 Turn off computer and unplug power cord 2 To connect signal cable with 15pin into VGA connector on the back of monitor and to be sure to tighten switches on both ends of signal cable 3 To plug PC and monitor adapter to the nearest socket 4 Turn on PC and monitor image possibility shows successful installation If not please double check all the connections NOTES 1 To connect signal cable and plug adapter to be assure monitor safety on process of installation 2 To avoid monitor damaged please handle the centre part of front cover while it installation E k HR POWER MAMA UI LD 0 y ou Front Panel Controls 4 MENU Press it to open the OSD MENU to select MENU options when the OSD MENU is displayed Hot key to adjust Brightness when the OSD is off Adjust value up selection button Hot key to adjust Contrast when the OSD is off Adjust value down selection button Hot key to automatically optimize positions phase and clock when OSD is not shown VGA only Press this button to turn on or off the monitor LED On Normal LED flicker Power Saving LED Off Power Off Operate Expla
5. hould never be placed near or over a radiator or heat register or installed in any enclosure that prevents proper ventilation 5 Do not place any object on the adapter Do not place this product where persons could walk on the adapter 6 Never push objects of any kind through the ventilation slots at the back of the product To do so could risk fire or electronic shock 7 Do not attempt to service this product by yourself Opening or removing covers may expose you to dangerous voltage that could cause fire or electronic shock Refer all servicing needs to authorized service personnel 8 Unplug this product from the wall outlet and contact authorized service personnel under the following conditions a When the adapter or plug is damaged or frayed b If a liquid has been spilled into or on the product c If the product has been rained or spilled by water d If the product has been dropped or the cabinet has been damaged e If the product does not operate normally when operating instructions are followed and product shows to be maintained Special Notice Only under normal condition can the quality of LED products be assured during operation Normal condition as following Temperature 5 C 35 C Humidity 20 85 No condensation Display image continuously changing image Not freezing image For the LED products the phenomenon of image stagnation may appear when display the freezing image for a certain long time All the
6. nation Your LCD has been adjusted to its optimal status before shipment You can also adjust the image in accordance with the following illustrations and steps e Press the MENU button to start the OSD feature e Click the A or y to select the function to be adjusted e Click the MENU button to access into the function to be adjusted e Click A or W button to change the current setting of the function e To exit OSD MENU or go back to the previous action by AUTO e To repeat above steps for changing the setting of the other function OSD Control e Contrast Press y adjust the Contrast e Brightness Press A adjust the Brightness e Auto phase and clock when OSD is not shown t Source Resoluticinn and Frequency Primary Secondary P Adjust the contrast of the image Col r Brightness Adjust the brightness of the screen Set up the color Temp to be 9300K 6500K 5500K oe Goror Temp USER red green blue to adjust red green blue Auto Adjust Set up to adjust clock phase and position automatically VGA only Color Adjust Adjust the color of the screen VGA only Move the image left and right on the screen VGA only Picture CH Move the image up and down on the screen VGA only Adjust the clock pulse of the image VGA only Adjust the focus of image VGA only Language Select the language you want OSD H Pos Move the OSD left and right on the screen OSD V Pos
Download Pdf Manuals
Related Search