Oregon Scientific RMR202A weather station
Contents
1. the actual display e When disposing of this product ensure it is collected separately for special treatment e Placement of this product on certain types of wood may result in damage to its finish for which Oregon Scientific will not be responsible Consult the furniture manufacturer s care instructions for information e The contents of this manual may not be reproduced without the permission of the manufacturer e Do not dispose old batteries as unsorted municipal waste Collection of such waste separately for special treatment is necessary e Please note that some units are equipped with a battery safety strip Remove the strip from the battery compartment before first use NOTE The technical specifications for this product and the contents of the user manual are subject to change without notice SPECIFICATIONS TYPE DESCRIPTION MAIN UNIT 77 x 41 5 x 116 5mm LxWxH enka 3 03 x 1 63 x 4 59 in 241 g 8 Weight aes without battery 5 C to 50 C 23 F to 122 F 0 1 C 0 2 F Temperature range Resolution Signal frequency 433 MHz Humidity range 25 95 Humidity resolution 1 Power 2 x UM 4 AAA 1 5 V batteries REMOTE UNIT THN132N 96 x 50 x 22 mm LxWxH i 3 78 x 1 97 x 0 87 in Weight Transmission range 62 g 2 22 ounces 30 m 98 ft unobstructed 20 C to 60 C 4 F to 140 F 1 x UM 3 AA 1 5 V batteries Temperature range Power ABOUT OREGON SCIENTIFIC Visit our webs2. OreGcon ENT 1 Cc Fic Tr cyan aa ems eee Oregon SCIENTIFIC Indoor and Outdoor Thermometer with Atomic Time Model RMR202A USER MANUAL Remote sensor reception indicator Clock signal reception indicator Indoor temperature MODE Change settings display 2 bY deactivate clock reception signal Outdoor temperature Time zone Clock with weekday MEM View current temperature humidity 10 Ice alert LED indicator N maximum and minimum 1 C F Select temperature unit 2 RESET Reset unit to default settings LED status indicator Wall mount hole Battery compartment RESET hole CHANNEL switch noe O I RMR202A indd 1 A V Increase decrease setting activate GETTING STARTED 1 Remove the battery compartment 2 Insert the batteries matching the polarities 3 Press RESET after each battery change LD LOCATION MEANING Clock alarm Main unit batteries low Outdoor temperature and humidity area REMOTE SENSOR The main unit can collect data from up to 3 sensors Sensor batteries low To set up the sensor 1 Open the battery compartment see FIG 3 2 Select a channel then press RESET 3 Close the battery door 4 Place the sensor within 30 m 98 ft of the main unit using the table stand or wall mount TIP Ideal placements for the sensor would be in any location on the exterior of the home at a height of not more than 5 ft and wh
3. ay month month day month day and language Select the time zone P Pacific E Eastern C Central or M Mountain NOTE The language options are English E German D French F Italian 1 and Spanish S To select display mode Press MODE to choose between clock with seconds weekday calendar TEMPERATURE AND HUMIDITY To toggle temperature unit Press C F To auto scan between sensors Press and hold W MEM to display each sensor s data for 3 seconds To end press A To toggle between current minimum and maximum records for the selected sensor Press MEM repeatedly To clear the records Press and hold MEM If the channel 1 sensor falls between 3 C to 2 C 37 F to 28 F LED indicator will flash and will stop flashing once the temperature is out of this range RESET Press RESET to return to the default settings PRECAUTIONS e Do not subject the unit to excessive force shock dust temperature or humidity e Do not cover the ventilation holes with any items such as newspapers curtains etc e Do not immerse the unit in water If you spill liquid over it dry it immediately with a soft lint free cloth e Do not clean the unit with abrasive or corrosive materials e Do not tamper with the unit s internal components This invalidates the warranty e Only use fresh batteries Do not mix new and old batteries e Images shown in this manual may differ from
4. equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help The following information is not to be used as contact for support or sales Please call our customer service number listed on our website at www oregonscientific com or on the warranty card for this product for all inquiries instead We Name Oregon Scientific Inc Address 19861 SW 95 Ave Tualatin Oregon 97062 USA Telephone No 1 800 853 8883 declare that the product Product No RMR202A Product Name Indoor and Outdoor Thermometer with Atomic Time Manufacturer IDT Technology Limited Address Block C 9 F Kaiser Estate Phase 1 41 Man Yue St Hung Hom Kowloon Hong Kong is in conformity with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation CE P N 086XXXXX XX 2007 6 21 9 12 49 AM
5. ich can shield it from direct sunlight or wet conditions for an accurate reading NOTE Use alkaline batteries for longer usage and consumer grade lithium batteries in temperatures below freezing To search for a sensor Press and hold MODE The sensor reception icon in the remote sensor area shows the status ICON DESCRIPTION OUT OUT gt Q Main unit is searching for p p sensor s ar Pon at Pot A channel has been p i i found The sensor cannot be found OUT TIP The transmission range may vary depending on many factors You may need to experiment with various locations to get the best results CLOCK This product is designed to synchronize its clock automatically with WWVB 60 signal within 3200km 2000 miles of Fort Collins Colorado To enable disable signal reception Press and hold to enable or W to disable signal reception NOTE Reception takes 2 10 minutes If the signal is weak it can take up to 24 hours to get a valid signal lf signal reception is unsuccessful place your unit next to a window press and hold A to force another signal search Clock signal reception indicator WEAK SIGNAL STRONG SIGNAL NO SIGNAL To set the clock manually disable the signal reception first 1 Press and hold MODE 2 Press A or y to change the settings 3 Press MODE to confirm 4 The settings order is time zone 12 24 hr format hour minute year calendar mode d
6. ite www oregonscientific com to learn more about Oregon Scientific products If you re in the US and would like to contact our Customer Care department directly please visit www2 oregonscientific com service support OR Call 1 800 853 8883 For international inquiries please visit oregonscientific com about international www2 FCC STATEMENT This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the
Download Pdf Manuals
Related Search