Clover Technologies Group LCD0935
Contents
1. 9 Ground Metal NIC O0O00 0 S 2345678 Side View Front View This light is lit in blue when the AC power supply is properly plugged to DC jack refer to 9 Select the CH1 camera by pressing this button in the manual mode or automatic sequential mode Press Down Y button to navigate the submenu Select the CH2 camera by pressing this button in the manual mode or automatic sequential mode Press Up A button to navigate the submenu Decrease audio level by pressing this button Press Left lt 4 button to select values Increase audio level by pressing this button Press Left button to select values Press this button to setup the menus Press and hold this button for 3 seconds to set the unit into playback VCR mode Press this button to place the system into the automatic sequential mode See section 6 4 Press this button to turn the power off Press and hold this button for 3seconds to turn the power on DC power jack Plug the provided AC power supply only Do not use the unproven AC power supply as this can result in fatal damage to the system In case of this the warranty term should be voided 11 Video inputs 6pin Din jack Connect a provided camera to the 6pin Din jack Make sure that the two arrows on the monitor and on the top of the cable should be aimed at each other 12 Audio input RCA jack Audio input port for VCR playing 13 Audio output R2. 2 TFT LCD active matrix System NTSC Pixel pitch 0 108 H x 0 376 V mm Luminance 300 cd m Viewing angle L R T B 45 65 65 65 degrees Power consumption 1 100 mA Operating temperature 5 C to 50 C Dimensions 260 W x 195 H x 40 D mm Weight 2 30 Lbs 7 2 Camera Image pickup device 1 4 C MOS TV system NTSC Array Size 656 x 492 Image Area 4 080 mm x 3 102mm Resolution 450 TV Lines Minimum illumination IR LED S N ratio Gamma characteristics Video output Microphone Exposure Time Range Lens Current consumption Power supply Housing material Operational temperature Dimensions Weight 0 Lux LED on 0 1 Lux F1 2 LED off 30pcs Wave Length 850nm More than 48db AGC off 0 45 1 0Vp p Composite 75 ohms Waterproof C Mic 1 60s 20us 3 6mm fixed lens 400 mA Max LED on DC 12V Regulated not included Die cast aluminum alloy 10 C to 50 C RH95 Max 55 x 95 L mm 1 1 Lbs 8 Appendix System Includes 1 9 2 TFT LCD monitor 1 Mounting bracket for monitor 2 Indoor Outdoor color camera w 60 cable amp mounting bracket 1 AC Power Supply for Monitor DC12V 3 0A 1 Remote Controller 1 Hex head wrench 1 Instruction Manual Limited 1Year Warranty This warranty gives the original purchaser specific legal rights and you may also have other rights which may vary from state to state If our products do not function because of any defect in material or workmanship we will repa
3. ceiling mount application depending on the setting 4 2 Installation of Camera Ceiling Mount Wall Mount 1 Attach the mounting bracket base to the wall or ceiling wherever you want to install the camera Locate a wall stud or ceiling joist and secure the bracket base using the supplied screws 2 Lock the mounting bracket with the locking ring 3 Turn the pivot locking screw with the provided hex head wrench counter clockwise to set the desired angle of camera toward objects and turn it clockwise to secure It can be used for wall mount or ceiling mount application depending on setting this pivot locking screw 4 Loosen the locking screw with the provided hex head wrench and turn the camera clockwise or counter clockwise to upright images on the screen and turn it clockwise to secure 5 Connect the one end of 60 cable to CH1 or CH2 Make sure that the two arrows on the top of 60 cable and on the monitor should be aimed at each other 5 OPERATION 5 1 Automatic Sequential Mode Press AUTO button on the front panel then the monitor will be displayed one camera after another The dwell time can be adjusted from 1 to 60 seconds in the SETUP menu See section 6 4 5 2 Manual Mode Press the desired camera button on the front panel of the monitor to display a full screen when the system is in the automatic sequential mode or manual mode 5 3 DVR VCR Operation Normally this system is in Record mode To rec
4. ec oc gt ec oc oc Com oc 0 OC OM 9 Cc oc oc oc oc oc 0 TM 7ec QA ec OA D 0 CO BCD 00 BCD BLOD BCD 6 CO oc 0C 0C OCD BCD 6 CO oc oc oC oC OCS cc oc oc oc otc om 9 Cc oc oc oc oc om a ec qoc tec ster self D a A cscmocmoca ec ec Tc 0 A 0 AB a o CA 0 CA 9 CO 0 CD 9 CO ec oc COD 2 0 COD A 0 COD D C3 9 CO B C 9 CO 0 a 8 a o 8 O ecm ec ec oc Coomomomomnoca am 6 CO 6 an 6 CD 8 an 6 CD E 0 CO 0 CO 0 CO 0 C oc C9 B CO 0 CO 0 CO 0 CO 8 C9 Ls K 1 L 1 a L E oo E E ao L 1 a C3 9 C0 8 CO 0 CO 8 CO 0 C CO BCD 9 COD BCD Kam B D 00 OD BOD BD BD 6 CH oc ec ec oc OM 0 c oc ec oc 0c oc 6 oc oc oc oc oc 0 ooo oh 0 Oo Oo 0 0c QA BA OTF OC 0 gt C BCD OC BCD oC 8 CO 0c BCD BCD 0C DOC D8 Cc 7c ec ec ec OC 0 1c oc 0c 0c om 0 Cc ec ec 0c oc oc 0 oe oc 0 BA ole BCD BCD BCD oC a BD 0 CO o0 OC oo BCD OC DO Cc BCD 0c oc GLCD OCD 9 O 0c 0c ec oc oc 8 Cc 0c oc oc oc oo oc ome oc oc 800 CD 00 D e o C0 C0 C e C0 CO 8 C BCA oeeo DO 0 DCD 0 BCD ol BCD OC BCD 6 CO 0c 0C BCD OCD BCD 6 o oc oc oc oc OC OO ecoeocmecmeocmocmo s 9 CO n E E n A a A E s E 4 Place the square metal on the top of the mounting bracket into the metal hole 5 on the rear of the monitor as shown illustration above then secure the monitor using the locking ring 5 Turn the tightening knob clockwise to secure the swivel after setting the desired angle of monitor to display It can be used for wall mount or
5. CA jack Audio output port for recording 14 Video input BNC Video input port for VCR playing 15 Video output BNC Video output port for recording Note Audio on the provided cameras is available 3 2 CAMERA 2 1 3 Camera 1 Lens 3 6mm fixed Lens 2 Infrared LEDs 30 Infrared LEDs let you see objects in the darkness 3 CDS sensor Automatically turns the Infrared LEDs on at night 4 Sunshield 5 Mounting bracket 6 60 6pin Din cable 4 INSTALLATION 4 1 Installation of Mounting Bracket for TFT LCD Monitor 1 Turn the tightening knob counter clockwise to disassemble the swivel 2 Place the fixed ring into the swivel as shown illustration above and turn the tightening knob clockwise to secure the swivel Pay attention not to miss the spring 3 Loosen the locking knob and set the proper angle of square metal on the top of the swivel Cc 8 C 0 CD 8 C 0 E C CO 9 C2 0 CO 8 CO 0 a oc CO eco ecm 6 CD 0 CD ec C9 9 CO 0 CO 8 CO 0 a 9 n CO 0 CD 0 0 0 CD B CD Coomomomomoc 9 CD 0 CO o CD 6 CD 8 CD c o E 0 CD 8 CD 0 CD 8 C 8 E 0 CO ol oe oe o 9 O 0 CO 9 CD 0 oo 9 C kam 6 C2 ee 8 CD oe ee C9 im 0 CD 8 CD M M E 8 C L oe eee CO 9 CO 9 CO Ea 0 a 9 C 09 C0 O el ol ee CO 9 CO 0 CO 8 CD 0 an 6 C CO ec gt oc gt ec OCD OC OO Cc ec oc gt oc oC gt oc 9 c oc oc oc oc oc 0 o 0c 7 otf ec aea DCD 9 T3ec jac BA OA B 0 CO BCD oC oC LCD BCD 6 Cc 6c oC ec oC oC o
6. INSTRUCTION MANUAL 9 2 TFT LCD COLOR MONITORING SYSTEM With 2 Indoor Outdoor Color Cameras MODEL LCD0935 Ver 061109 011510 W Wisecomm Copyright 2009 Wisecomm All Rights Reserved 1 IMPORTANT SAFETY PRECAUTIONS To prevent fire or shock hazard do not expose the monitor to rain or moisture To avoid electrical shock do not open the case of this product Operate this product using only the supplied power supply Do not overload electrical outlets or extension cords this can result in fire or electric shock Keep this product away from strong magnetic fields Do not expose this product in direct sunlight or strong reflected rays Do not use thinner or other cleanser to clean the unit Please wipe out the unit with a soft cloth if it gets dirty Refer servicing to qualified personnel only Do not change or modify this product the warranty terms will be voided 2 FEATURES Easy installation 9 2 TFT LCD display Resolution 640 x 480 2Ch line locked sequential switcher 2 two 6pin Din video inputs for included cameras True Day Night cameras built in waterproof C microphone Built in ICR IR Cut Filter Removal Up to 60 IR range depends on scene reflection On screen display Programmable dwell times up to 60 seconds DVR or VCR Recordable 3 CONNECTIONS 3 1 TFT LCD MONITOR 10 15 13 14 12 gt 11 10
7. ir it for free for 1 year on parts and labor from the date of original purchase This warranty does not cover modification abuse incidental or consequential damages unless the state of owner s residence specially prohibits limitations on incidental or consequential damages How to obtain Factory Service Original purchaser must fill out the warranty card and mail it to the factory with the model number serial number and the date of purchase We will repair or replace and return the system to the owner under this limited watranty Please pack the system carefully and securely using the original packing materials and send it prepaid and insured to 13073 E 166th St Cerritos CA 90703 Please include a check for 20 00 to cover the cost of return postage and handling If the system is returned within the warranty period please include a proof of purchase If the system is out of warranty you will receive an estimate of the repair cost for your approval before repair work will be started
8. ons and select the values with the and the buttons To return to the MAIN MENU select the EXIT with the Aand the V buttons and then press the MENU button 6 4 System Menu E Press the MENU button on the front panel to setup the menus Select the SYSTEM MENU icon in the MAIN MENU by using the and the lt buttons Choose an item with the A and the Y buttons and select the values with the and the lt 4 buttons To return to the MAIN MENU select the EXIT with the Aand the V buttons and then press the MENU button Reset Select the Reset in the SYSTEM MENU to reset to the factory default values Blue Select the Blue in the SYSTEM MENU to display in blue when no video signal or weak signal Auto Power Down Choose one among 15 30 45 and 60 to turn the power off automatically after the selected time in minute Sharp Adjust the sharpness of images Panel LR You can view the mirror images or normal images by selecting Panel UD You can view the reverse images or normal images by selecting AUTO SWITCH Select the dwell time for the automatic sequential mode VCR Select VCR in the SYSTEM MENU and press or the lt buttons to set the system in playback mode To return to live mode press CH1 or CH2 6 5 Exit EA To exit the MAIN MENU select the EXIT with the Aand the V buttons and then press the MENU button 7 SPECIFICATIONS 7 1 TFT LCD Monitor Display 9
9. ord connect cables not included to the AUDIO IN OUT and VIDEO IN OUT ports on the monitor and vice versa on the DVR VCR Then press the REC button on the DVR VCR Press the PLAY button on the DVR VCR To play back press the MENU VCR button on the front panel for 3seconds or select the VCR in the SYSTEM menu refer to system menu 6 SETUP THE MENUS It is impossible to setup the menus if images are not being displayed on the screen Press the MENU button on the front panel to setup the menus All the menus will automatically disappear if you don t change values within 10 seconds The remote controller may not control all the functions on the system In case of this please use the buttons on the front panel 6 1 Video Enhancement O Press the MENU button on the front panel to setup the menus Select the VIDEO INHANCEMENT icon in the MAIN MENU by using the gt and the lt buttons Choose an item with the A and the V buttons and select the values with the and the lt buttons To return to the MAIN MENU select the EXIT with the Aand the V buttons and then press the MENU button S21 6 2 Language g Other languages except English are not available on this model 6 3 Audio Volume Ea Press the MENU button on the front panel to setup the menus Select the AUDIO VOLUME icon in the MAIN MENU by using the and the lt buttons Choose an item with the A and the Y butt
Download Pdf Manuals
Related Search