Baumatic MEGA10WD washer dryer
Contents
1. Instruction manual Baumatic Washing Machine Instruction Manual MEGA10WD MEGA10W INSTRUCTION MANUAL m Economic wash system Using artificial intelligence the washer uses minimum energy and water by selecting optimal water level and washing time E Low noise system The washer minimises the washing and spinning noises by sensing the amount of laundry E Child Lock The Child Lock system has been used to prevent children from pressing any buttons to change the programme during operation m Nano silver sterilization washing By applying very fine silver particles on essential parts inside the washer sterilizes up to 99 9 as is done by boiling wash E Air bubble washing This is an advanced technology that generates millions of air bubbles inside the drum during a washing sequence The bubbles dissolve the detergent particles completely and cleanse all the soil in clothes gently and neatly 21060955 CONTENTS Page PARTS AND FEATURES 2 WASHING MACHINE SAFETY 3 INSTALLATION INSTRUCTIONS 4 INLET HOSE CONNECTION 5 ELECTRICAL REQUIREMENTS 7 OPERATING YOUR WASHING MACHINE 8 THE FUNCTIONS OF THE WASHING MACHINE CONTROL PANEL 10 WASHING PROGRAMMES 12 WASHING PROCEDURE AND SELECTION 13 GUIDE FOR OTHER USEFUL PROGRAMS 24 MAINTENANCE 28 HOW TO CLEAN THE FILTER 29 REMOVING STAINS 30 TROUBLE SHOOTING 31 CONDITIONS OF GUARANTEE 32 SERVICE CONTACTS 33 A NOTE TO YOU Thank you for buying a Baumatic appliance Baumat2. These items should have more room to move in the water than heavy items towels jeans Adding detergent 1 Detergent compartment Main wash bre wash Fabric softener 2 Adding fabric softener If desired pour liquid fabric softener into the dispenser using the amount recommended by the manufacturers Do not exceed the maximum fill line Overtilling can cause early dispensing of the fabric softener which could stain clothes Do not open the detergent case when water is supplied e Avoid pouring fabric softener directly on the clothes zz THE FUNCTION OF CONTROL PANEL MEGA10WD Press this button to turn the power ON or OFF Operation and temporary stop is repeated as it is pressed When you want to change a programme while operating Press the Start Pause button Select the programme that you want to change gt Press the Start Pause button again You can select the programme you want and each lamp is turned on when that course is selected As this button is pressed the wash cycle is selected by Quick Wash proper load amount 1 2kg gt Small proper load amount 2 3kg gt Main Wash gt Pre Wash gt Soak gt Quick Wash You can select the rinse time s you want and each lamp is turned on when that course is selected As this button is pressed the rinse time s is selected by 1 gt Rinse Hold gt
3. a bleach that is safe for the fabric e Put the stained area face down on a paper towel or white cloth Apply the stain remover to the back of the stain This forces the stain off the fabric instead of through it Stain removal guide STAIN TO REMOVE Blood Rinse immediately in COLD water If stain remains soak in cold water with an enzyme prewash Chewing gum Use ice in a plastic bag to harden the gum Scrape off what you can and then sponge with white spirits Cocoa Chocolate Sponge with COLD water and soak in an enzyme prewash If stains persist rub in a little detergent and rinse in cold water Coffee Blot up quickly and rinse out in COLD water Rub in a little detergent and wash in the maximum temperature allowed for the fabric type Cream Milk Rinse in COLD water and wash normally Ice cream If stain is still apparent sponge with white spirits Deodorant Rub affected area with white vinegar and then rinse out in COLD water Sponge with white spirits Treat stiffened areas with enzyme prewash Egg Soak in a COLD enzyme prewash rinse and wash normally Fabric Softener Rub affected area with a bar of soap and wash normally Fruit stains Treat as soon as possible by sponging with COLD water Rub a little detergent on the stain and wash normally Grass Sponge with white spirits Rub in an enzyme prewash and wash as normal Grease and oil Lay the affected area face down on an absorbent cloth
4. and work from the back Sponge with white spirits or dry cleaning fluid Wash normally Iron or rust Apply lemon juice and salt and place in the sun Wash normally Lipstick Sponge with white methylated spirits and wash normally Mildew Wash in WARM water and detergent Moisten area with lemon juice dry in the sun and wash normally If stain persists and the fabric allows use bleach Mud Brush off any dry mud Rinse in cold water If stain persists rub in a little detergent and wash normally Paint oil based Scrape off any fresh paint and sponge with a non flammable dry cleaning fluid and wash normally Paint water based Treat while still wet rinse in WARM water and wash normally Scorch marks Dampen a cloth with hydrogen peroxide lay it over the affected area and press with a fairly hot iron 30 TROUBLE SHOOTING Most problems are easily solved if you understand the cause Check the following list for problems before calling for service If error mode such as IE OE UE are displayed on the control panel first open and close the door and then press START PAUSE button PROBLEM CHECK POINT The machine will not operate at all e Is there a power failure e Is the power cord correctly connected to an electric outlet e Did you turn on the power e Did you press Start Hold button e Is there the correct amount of laundry in the washer e Water is no
5. e Water temperature 95 C and Spin speed 1200 are not selected e If you want to add the clothes during operation press the Start Pause and Door unlock buttons then open the Door and put the clothes into the Drum Then close the door and press the Start Pause button again 16 5 HEAVY STRAIN PROGRAMME Put the laundry into the drum Then close the Door In the detergent compartment put the powder into the main wash and prewash Step 1 sections See Diagram Page 9 e Softener should be poured into the middle section of the compartment and be below MAX level Put the detergent into the pre wash section only if you want to add prewash e When you want to use bleach put it into the main wash section with detergent Press the Power button Sepe e The LED shows this signal Select the HEAVY STRAIN programme using the programme selection dial If you press the Start Pause button after pressing the Power button without selecting a programme the NORMAL programme is selected as default programme e Pre wash 3 times rinse 800 rpm spin speed and 40 C water temperature Step 3 are selected automatically e If you want to change the Washing programme Rinse time s Spin speed and water temperature select the programme you want by pressing the relevant buttons Press the Start Pause button Step 4 e The washing machine will start operating by locking
6. gt 30 40T gt 60C gt 95 RINSE SPIN It is used to perform the Rinse and Spin programs only OO TEMP _ RINSE SPIN Use this function when you want to prevent any accident occurring from handling of the washer by a child During operation of the washer press TEMP and RINSE SPIN buttons simultaneously If this mode will be set successfully CHL and remain time will be shown on PCB board alternately In Child Lock mode no button functions except the Power button If you want to set this mode press TEMP and RINSE SPIN buttons simultaneously within 3 seconds And if you want to release this mode press TEMP and RINSE SPIN buttons simultaneously within 3 seconds If you want to change to the desired program while this mode is working 1 Press TEMP and RINSE SPIN buttons simultaneously again during 3 seconds 2 Press the Start Pause button 3 Select the desired program and press the Start Pause buttom again 2 sam 5 Change u amp m the desired PR Tem py JErspin program The Child Lock mode can be set at any time and it is automatically released when operation errors happen Also this mode works when the power is off It you want to open the Door intentionally during operation press the Start Pause button and then press Door unlock button This signal will appear on PCB board then you can open Door after the Tub has cooled inside and the water has drai
7. pressing the Power button without selecting a programme the NORMAL programme is selected as default programme Step 3 e Main wash 2 times rinse 400 rom spin speed and Cold water temperature are selected automatically e If you want to change the Washing programme Rinse time s and Spin speed select the programme you want by pressing the relevant buttons Press the Start Pause button Step 4 e The machine will start operating by locking the Door and supplying water Note e If you want to change the programme setting during operation press the Start Pause button to hold the operation and change to the programme you want by pressing each corresponding button e Water temperature Cold is only selected in order to prevent delicate clothes from becoming damaged e Spin speed 400 and 600 are only selectable e DRY function is not selected optional function e DELAY START is not selected e SOAK and Pre Wash in wash programme are not selected e If you want to add clothes during operation press the Start Pause and Door unlock buttons then open the Door and put the clothes into the drum Then close the Door and press Start Pause button again 19 8 BLANKET PROGRAMME Put the laundry into the drum Then close the Door In the detergent compartment put the powder into the main wash section Step 1 y See Diagram Page 9 e Softener should be below MAX level e When you w
8. speed select the programme you want by pressing the relevant buttons Step 4 Press the Start Pause button The machine will start operating by locking the door S Note e If you want to change the programme setting during operation press the Start Pause button to hold the operation and change to the programme you want by pressing each corresponding button e Water temperature Cold is only selected in order to prevent woolens from being damaged e Spin speed 400 and 600 are only selectable e DRY function is not selected optional function DELAY START is not selected SOAK and Pre Wash in wash cycle are not selected e If you want to add clothes during operation press the Start Pause button and Door unlock buttons then open the Door and put the clothes into the drum Then close the Door and press the Start Pause button again 18 7 DELICATE PROGRAMME Put the laundry into the drum Then close the Door Step 1 In the detergent compartment put the powder into the main wash section See Diagram Page 9 e Softener should be poured into the middle section of the compartment and be below MAX level e When you want to use bleach put it into the main wash section with detergent Step 2 Press the Power button e The LED shows this signal Select the DELICATE programme using the programme selection dial If you press the Start Pause button after
9. supply cord Non use or vacation care Operate your washing machine only when you are at home If you are on holiday or your machine is not being used for an extended period of time you should e Unplug the power supply cord or turn off electrical power to the washer e Disconnect the water supply This helps avoid accidental flooding due to a water pressure surge while you are away HOW TO CLEAN THE FILTER Cleaning the water inlet filter Clean the filter when water leaks from the water inlet Pull the power plug out before cleaning the filter SE Turn off the water supply to the washer and separate the inlet hose Pull the inlet filter out Remove the dirt form the inlet filter with a brush Cleaning the drain filter This drain filter is used to screen the foreign bodies such as threads coins pins buttons etc If the drain filter is not cleaned regularly after every ten washes drainage problems could arise CAUTION Be careful when draining if the water is hot 1 Open the lower cover 1 by 2 Unplug the cap hose 2 allowing 3 Remove any foreign material using a coin Remove the cap the water to flow out At this time from the pump filter 3 After hose 2 to pull out the hose use a vessel to prevent water cleaning tum the pump filter flowing on to the floor When water clockwise and insert the cap does not flow any more tum the hose 2 to the original place pump filter 3 o
10. 2 gt Rinse Hold gt 5 gt Rinse Hold gt 1 You can select the spin speed you want and each lamp is turned on when that course is selected There is a timer control which can delay the start of the wash from one to twelve hours This can be used to adjust water temperature according to types of the load to be washed As this button is pressed water temperature is selected by Cold gt 30 40T gt 60T gt 95 You can select the dry condition you want and each lamp is turned on when that cycle is selected elo TEMP DRY Use this function when you want to prevent any accident occurring from the machine During the operation of the machine press TEMP and DRY buttons simultaneously within 3 seconds If this mode is set successfully CHL and the remaining time will be shown on the display panel alternately In Child Lock mode no button functions except the Power button If you want to release this mode press TEMP and DRY buttons simultaneously again during 3 seconds If you want to change to the desired program while this mode is working 1 Press TEMP and DRY buttons simultaneously again within 3 seconds 2 Press the Start Pause button 3 Select the desired program and press the Start Pause buttom again gt sus gt Change gt soar NEN NE the desired Ni Re pa en program The Child Lock mode can be set at any time and it is automatically released when operation
11. and press Start Pause button again 20 9 RAPID PROGRAMME Step 1 Put the laundry into the drum Then close the Door In the detergent compartment put the powder into the main wash section See Diagram Page 9 Softener should be poured into the middle section of the compartment and be below MAX level e When you want to use bleach put it into the main wash section with detergent Step 2 Press the Power button e The LED shows this signal Step 3 Select the RAPID programme using the programme selection dial e If you press Start Pause button after pressing the Power button without selecting a programme the NORMAL programme is selected as default programme e Main wash 2 times rinse 800 rom spin speed 30 C water temperature and Cupboard dry condition are selected automatically If you want to change the Washing cycle Rinse time s Spin speed and water temperature select the programme you want by pressing the relevant buttons Step 4 Press the Start Pause button e The machine will start operating by locking the Door and supplying water Note e The appropriate amount of laundry is below 3 kg e If you want to change the programme setting during operation press the Start Pause button to hold the operation and change to the programme you want by pressing each corresponding button e Water temperature Cold 30 C a
12. ant to use bleach put it into the main wash room I marking with detergent Press the Power button pepe e The LED shows this signal Select the BLANKET programme using the programme selection dial If you press Start Pause button after pressing the Power button without selecting a programme the NORMAL programme is selected as default programme Step 3 e Main wash 3 times rinse 800 rpm spin speed and Cold water temperature are selected automatically If you want to change the Washing programme Rinse time s and Spin speed select the programme you want by pressing the relevant buttons Press the Start Pause button Step 4 e The machine will start operating by locking the Door and supplying water Note e If you want to change the programme setting during operation press the Start Pause button to hold the operation and change to the programme you want by pressing each corresponding button Water temperature Cold is only selected in order to prevent delicate clothes from being damaged e Spin speed 400 and 600 and 800 are the options available DRY function is not selected optional function e DELAY START is not selected e SOAK and Pre Wash in wash programme are not selected e If you want to add clothes during operation press the Start Pause and Door unlock buttons then open the Door and put the clothes into the drum Then close the door
13. ash Rinse 2 Spin 400 Temp cold Refer to rating label Blanket Blankets curtains etc Cold fixed in order to prevent textile damage Wash main wash Rinse 3 Spin 800 Temp cold Refer to rating Lightly soiled clothes frequently washed items and small amounts of clothing 30 C cold 40 C Wash main wash Rinse 3 Spin 800 Temp cold Dry cupboard Memory Use to memorise program you want Drum Cleaning Use to clean and dry the Tub and Drum 12 Wash soak Rinse 2 Spin 400 Temp cold Dry cupboard a WASHING PROCEDURE AND SELECTION 1 NORMAL PROGRAMME Put the laundry into the Drum Then close the Door In the detergent compartment put the powder into the main wash and prewash Step 1 sections See Diagram Page 9 e Softener should be poured into the middle section of the compartment and be below MAX level e Put the detergent into the pre wash room marking only if you want to add prewash e When you want to use bleach put it into the main wash room I marking with detergent Press the Power button alepa The LED shows this signal Select the NORMAL programme using the programme selection dial If you press the Start Pause button after pressing the Power button without selecting a programme the NORMAL programme is selected as default programme Step 3 e Main wash and 3 times r
14. case of the dual valve model with only the cold water inlet valve connected and the water temperature is selected as hot or warm there may be water leakage from unconnected water inlet valve e This appliance must be earthed a INSTALLATION INSTRUCTIONS Removing transit bolts 1 Before operating the washer remove the 2 Unscrew the 4 bolts with the spanner transit bolts 4 each along with the rubber supplied Keep the 4 bolts and spanner for e If the bolts are not removed it may cause future use heavy vibration noise and malfunction Whenever the appliance is transported the transit bolts must be refitted N Om 3 Close the holes with the Blanking Caps supplied Location of washer e Check the location where the machine will be installed Make sure you have everything necessary for correct installation Do not place or store your washing machine below 0 C 32 F to avoid any damage from freezing e Never place store laundry products on top of the machine Install the washer on the horizontal solid floor If the washer is installed on an uneven floor it could make considerable noise vibrate severely and cause a malfunction If the machine is not level adjust the legs up or down for horizo
15. e guarantee on the original product purchased The guarantee does not cover Sinks and taps Failure to comply with the manufacturers instructions for use The replacement of cosmetic components of accessories Accidental damage or wilful abuse Subsequent loss or damage owing to the failure of the appliance or electrical supply Incorrect installation Losses caused by Acts of God civil war failure to obtain spare parts strikes or lockouts Filters fuses light bulbs external hoses damage to bodywork paintwork plastic items covers baskets trays shelves burner bases burner caps decals corrosion rubber seals In the course of the work carried out it may be necessary to remove the appliance from it operating position Whilst all reasonable care will be taken Baumatic Ltd cannot accept responsibility for damage sustained to any property whatsoever in this process This guarantee is in addition to and does not diminish your statutory or legal rights Contacting Baumatic Ltd Sales Service Spares Technical Advice TEL 0118 933 6900 TEL 0118 933 6911 TEL 0118 933 6922 0118 933 6933 FAX 0118 931 0035 FAX 0118 986 9124 FAX 0118 933 6942 0118 933 6942 For ROI Republic of Ireland please contact one of the numbers below TEL 01 6266798 FAX 01 6266634 Thanks you for buying Baumatic Applies to UK Scotland Wales amp Northern Ireland only Republic of Ireland has 1 year labour amp 1 year parts warranty
16. e using the programme selection dial If you press the Start Pause button after pressing the Power button without selecting a programme the NORMAL programme is selected as default programme e Main wash 3 times rinse 800 rpm spin speed and 95 C water temperature are selected automatically e If you want to change the Washing programme Rinse time s and Spin speed select the programme you want by pressing the relevant buttons Step 4 Press the Start Pause button e The washing machine will start operating by locking the door and supplying water after sensing the amount of laundry automatically Note e If you want to change the programme setting during operation press the Start Pause button to hold the operation and then change to the programme you want by pressing each corresponding button e Water temperature is set only to 95 C e If you want to add the clothes during operation press the Start Pause and Door unlock buttons then open the Door and put the clothes into the Drum Then close the Door and press the Start Pause button again e Sometimes large amounts of suds occur The washing machine will clean away the suds automatically 14 3 ECO WHITE PROGRAMME Put the laundry into the drum Then close the Door In the detergent compartment put the powder into the main wash and prewash Step 1 sections See Diagram Page 9 e Softener should be
17. errors happen Also this mode works when the power is off If you want to open the Door intentionally during operation press the Start Pause button and then press the Door unlock button This signal will appear on the display then you can open the Door after the Tub has cooled inside and the water has drained away Also no button functions except the Power button 10 oo zz THE FUNCTION OF CONTROL PANEL MEGA10W S26 7676 6 WASH RINSE SPIN TIMEDELAY TEMP RINSE SPIN Press this switch to turn the power ON or OFF Operation and temporary stop is repeated as it is pressed When you want to change the program operating Press the Start Pause button gt Select the program that you want to change gt Press the Start Pause button again You can select the course you want and each lamp is turned on when that course is selected You can select the wash course you want and each lamp is turned on when that course is selected You can select the rinse time s you want and each lamp is turned on when that course is selected You can select the spin speed you want and each lamp is turned on when that course is selected It can be used to pre engage time for wash from 1 hr to 12 hrs TEMP It can be used to adjust water temperature according to the types of load to be washed As this button is pressed water temperature is selected by Cold
18. ic washing machines are easy to use save time and help you manage your home better This manual contains valuable information about how to operate and maintain your machine properly and safely Please read it carefully PARTS AND FEATURES The parts and features of your machine are illustrated on this page Do familiarise yourself with all parts and features before using It ARE Sane Sa a eas a aL ee a sla Tae eee cas en a NOTE I The drawings in the book may vary from your particular model They are designed to show the different features of all models covered by this book therefore your model may not include all features RAT T T E E E ere eee ER INLET HOSE D COLD DETERGENT CASE if POWER CORD Ol J CONTROL PANEL Be a e lt p A HOSE DRAIN FILTER COVER AA ADJUSTABLE LEG LOWER PANEL ACCESSORIES gt WASHING MACHINE SAFETY Save these instructions Your safety is important to us To reduce the risk of fire electrical shock or injury when using your washing machine adhere to the following basic precautions Read all instructions before using your washing machine e Flammable fluids dry cleaning solvents etc should not be used or stored in or near your machine Do not add flammable fluids to your wash These substances give off vapours that can create a fire hazard or explosion Do not attempt to open the door after a cycle has started Do
19. ide out to avoid damage the tibres e Tie strings and sashes to avoid tangling Treat spots and stains See Removing stains on page 30 Y Y 3 AE 4 Sy Sorting e Separate heavily soiled items from lightly soiled ones even if they would normally be washed together e Separate dark colours from light colours colourfast items from non colourfast items Soil Heavy Normal Light Colour White Lights Darks Lint Lint producers Collectors Separate clothes according to amount of soil Separate white clothes from coloured clothes Wash lint producers and lint collectors separately Loading For best cleaning and wrinkle free results put clothes into the machine loosely so that they move easily in the water Load machine properly and select correct load size setting Overloading and selecting a setting too small for the wash load can Cause poor cleaning Increase wrinkling Create excessive lint Wear out items faster because of damage to fibres e Mix large and small items in each load Load evenly to maintain washer balance An unbalanced load can make the washer vibrate during spin Reduce wash time when using a small load size setting Loads with only a few small items needs less wash time Use a large load size setting to reduce wrinkling with permanent press clothes and some synthetic garments
20. ing cycle during this procedure by pressing the WASH button 27 MAINTENANCE Proper care of your washer can extend its life This section explains how to care for your washer properly and safely Cleaning your washer Exterior Interior Wipe up detergent bleach and other spills with a soft damp cloth or sponge as they occur Occasionally wipe the outside of the washer to keep it looking like new gt Clean interior with 250ml of chlorine bleach mixed with 500ml of detergent Run washer through a complete cycle Repeat this process if necessary Check all pockets for sharp or metal objects eg keys pins clips money etc They may damage the interior of your machine If any such items are found please do not rest or leave them on top of the machine Winter storage or moving care Install and store your machine where it will not be subject to freezing temperatures as any water left in hoses etc may damage it If you wish to store move your machine during freezing weather please take note of the following To store move the machine To use washer again e Disconnect from mains Disconnect and drain water inlet hoses Run the washing machine on a drain and spin setting see pages 10 11 for 1 minute Unplug the power supply cord e Flush water pipes and hoses Reconnect water inlet hoses Reconnect to water supply Reconnect power
21. inse and 800 rom spin speed and 40 C water temperature are selected automatically e If you want to change the Washing programme Rinse time s Spin speed and water temperature select the programme you want to change by pressing each button Sten 4 Press the Start Pause button ep e The washing machine will start operating by locking the Door and supplying water Note e If you want to change the programme setting during operation press the Start Pause button to hold the operation and then change to the programme you want by pressing each corresponding button e Water temperature 95 C is not selected in order to prevent clothes from being damaged e If you want to add clothes during operation press the Start Pause and Door unlock buttons then open the Door put the clothes into the drum then close the door and press the Start Pause button again 13 2 WHITE PROGRAMME Step 1 Put the laundry into the Drum Then close the Door Put the detergent into the main wash and prewash sections See Diagram Page 9 Softener should be poured into the middle section of the compartment and be below MAX level Put the detergent into the pre wash section only if you want to add prewash e When you want to use bleach put it into the main wash section with detergent Step 2 Press the Power button e The LED shows this signal Step 3 Select the WHITE programm
22. install repair or replace parts on your machine Level adjustment ET ES Fe as N _ N ar 1 If the washer is installed on an Su eam 7 ie 2 er y Heh PER ae uneven floor it could make whys FERNE aD n E SS 7 x ag N Pj considerable noise vibrate and E SY Y A i D u p cause a malfunction Toa aa en ut 2 Adjust the level of the washing machine using the adjustable legs e Please check if there is any gap between the four adjustable legs and the floor e Turn the adjustable legs using the enclosed spanner adjust the level of the machine and make sure that it is stable e Adjust the fixing nuts up tightly so that the machine maintains the adjustment Cc Fixing Nut adjustable leg 3 Make sure that the washing machine does not move when you press down the four corners of the washer s top plate ee Zu ee ee ee ne ed NOTE i There should be no instability of the machine when all the adjustable legs are stuck to the floor closely I OPERATING YOUR WASHING MACHINE To obtain the best washing results you must operate your machine properly This section gives you this important information Preparing clothes for washing e Close zippers snaps and hooks to avoid snagging other items Remove pins buckles and other hard objects to avoid scratching the washer interior Empty pockets and pull them inside out e Turn down cuffs and turn synthetic garments ins
23. ished e A little shrinkage and deformation sometimes happens during drying so check clothes whether dry or not previously If you wish to use the dryer feature immediately following washing after selecting the programme press the DRY button then press the Start Pause button Please note this programme will only function if the wash does not exceed the weight recommended for the dryer 26 RINSE SPIN MEGA10W Put the laundry into the Drum and put softener into the detergent compartment Then close the Door ep Softener should be poured into the middle section of the compartment and be below MAX level Step 2 Press the Power button ep The LED shows this signal Select the programme you want using the programme selection dial Step 3 If you press RINSE SPIN button without selecting a programme the NORMAL programme is selected as the default programme Press the RINSE SPIN button e 1 time rinse 800 rom spin speed and Cold water temperature are selected Step 4 automatically P 400 rom spin speed is selected in the WOOL and DELICATE programme e If you want to change the Rinse time s and Spin condition press each corresponding button Press the Start Pause button Step 5 e The machine will start operating by locking the door and supplying water Note e It is possible during this cycle to select the temperature of the water e You can incorporate the wash
24. lify for your full 24 months guarantee you must register your appliance within 28 days of purchase to be covered under this guarantee This can be done online via www baumatic co uk or through returning the guarantee card which can be found in each new Baumatic appliance In addition your appliance is covered by a 5 year parts warranty Baumatic Ltd will provide free of charge the parts required to repair the appliance only if they are fitted by a Baumatic engineer for any defect that arises due to faulty materials or workmanship within a period of 5 years from the original purchase date An additional to 3 year insurance scheme for labour is available should you wish to extend the warranty period Should any person other than an authorised representative of Baumatic Ltd interfere with the appliance the policy is negated and Baumatic Ltd will be under no further liability The guarantee covers the appliance for normal domestic use only unless otherwise stated Any claims made under the terms of the guarantee must be supported by the original invoice bill of sale issued at the time of purchase This guarantee is transferable only with the written consent of Baumatic Ltd If the appliance fails and is considered either not repairable or uneconomical to repair between 12 months 2 years if registered and five years a free of charge replacement will not be offered The guarantee for any replacement will only be for the remainder of th
25. nd 40 C are selectable e Spin speed 1200 is not selected e All wash programmes are not selected except main wash e If you want to add the clothes during operation press the Start Pause and Door unlock buttons then open the Door and put the clothes into the drum Then close the door and press the Start Pause button again 21 10 MEMORY PROGRAMME Put the laundry into the drum Then close the Door In the detergent compartment put the powder into the main wash and prewash Step 1 sections See Diagram Page 9 Softener should be poured into the middle section of the compartment and be below MAX level e Put the detergent into the pre wash room l marking only if you want to add prewash e When you want to use bleach put it into the main wash section with detergent Press the Power button PR The LED shows only signal Select the MEMORY programme using the programme selection dial If you press the Start Pause button after pressing the Power button without selecting a programme the NORMAL programme is selected Step 3 If you want to memorise the Washing programme Washing course Rinse time s Spin speed water temperature and Dry condition select the programme you want by pressing the relevant buttons and using the programme selection dial Press the Start Pause button Step 4 e The washer will start operating by locking the Doo
26. nd press the Start Pause button again 15 4 SYNTHETIC PROGRAMME Step 1 Put the laundry into the drum Then close the Door In the detergent compartment put the powder into the main wash and prewash sections See Diagram Page 9 Softener should be poured into the middle section of the compartment and be below MAX level e Put the detergent into the pre wash section only if you want to add prewash e When you want to use bleach put it into the main wash section with detergent Step 2 Press the Power button e The LED shows this signal Step 3 Select the SYNTHETIC programme using the programme selection dial If you press the Start Pause button after pressing the Power button without selecting programme the NORMAL programme is selected as default programme e Main wash 3 times rinse 800 rpm spin speed and 40 C water temperature are selected automatically e If you want to change the Washing course Rinse time s Spin speed and water temperature select the programme you want by pressing the relevant buttons Step 4 Press the Start Pause button e The washing machine will start operating by locking the the Door and supplying water Note e If you want to change the programme setting during operation press the Start Pause button to hold the operation and change to the programme you want by pressing each corresponding button
27. ned away Also no button functions except the Power button 11 WASHING PROGRAMS Program Fabric type Colourfast garments shirts night dresses pyjamas and lightly soiled white cottons underwear Proper Temp 40 cold 30 C 60 C Default data Wash main wash Rinse 3 Spin 800 Temp 40 C Maximum Load Refer to rating label First check whether laundry is machine washable white cotton linen towel and sheets Wash main wash Rinse 3 Spin 800 Temp 95 C Refer to rating label Eco White First check whether laundry is machine washable white cotton linen towel and sheets 40 C Wash main wash Rinse 3 Spin 800 Temp 60 C Refer to rating label Synthetic Polyamide Acrylic Polyester 40 C cold 30 C 60 C Wash main wash Rinse 3 Spin 800 Temp 40 C Refer to rating label Heavy Stains Heavily soiled clothes blue jeans climbing clothes ruck sacks sports wear 40 cold 30 C 60 C Wash pre wash Rinse 3 Spin 800 Temp 40 C Refer to rating label Machine washable woolens with pure new wool only Cold fixed in order to prevent textile damage Wash main wash Rinse 2 Spin 400 Temp cold Refer to rating label Delicate Delicate laundry easily damaged silk curtains Cold fixed in order to prevent textile damage Wash main w
28. ngated by stretching e Water drain hose should be mounted at a height of a minimum of 60 cm to a maximum of 100 cm from the ground e The end of the water drain hose may be directly fitted to the waste water outlet connection or to a standalone pipe The standpipe should have a diameter of approximately 38 mm see diagram ensuring there is an air break between the drain hose and standpipe C Baag EIER andre GEN n t zl Wead un ne nun mn en e NEVER attempt to extend the water drain hose by adding additional hosing ELECTRICAL REQUIREMENTS WARNING Electrical shock hazard Failure to follow these instructions could result in death or serious injury An electrical earth is required on this machine If it does not fit the outlet have a proper outlet installed by a qualified electrician Don t earth to a gas pipe Don t change the power supply cord plug Check with a qualified electrician if you are not sure the machine is properly earthed RECOMMENDED EARTHING METHOD For your personal safety this machine must be earthed It is fitted with a supply lead attached to an earthed plug To prevent electric shock occurring this machine must be plugged into the relevant earthed power socket It is the personal responsibility and obligation of the customer to ensure that this is in place before the washing machine is installed PLEASE have only a qualified person
29. not tamper with the controls e The appliance is not intended for use by young children without supervision e If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard e If the appliance is connected to the power supply via an extension lead it should not be positioned where it could be splashed by or become susceptible to water Please e Have only a qualified person install repair or replace parts on washer Ensure your washing machine is regulary maintained and serviced Position your washing machine where it will be protected from the weather and keep it where the temperature will not fall below freezing e Do not install your machine at a place of extremely high humidity It could cause an electric shock or a short circuit e Your washing machine muse be connected to the correct outlet electrical supply water supply and drain supply Understanding your responsibilities Do not use chlorine bleach and ammonia or acid such as vinegar or rust remover in the same wash Hazardous fumes can form e Unplug power supply cord before attempting to service your machine Do not wash fibreglass material Small particles can stick to fabrics washed in following loads and cause skin irritation e Do not spray water on the control panel of the washer It could cause fire or an electric shock In
30. ntal installation Ventilation openings must not be obstructed by carpeting when the machine is installed on a carpeted floor e Leave some space right amp left 2cm rear 10cm 2cm e In case of built in installation the distance between top of the washer and bottom of upper plate approx 2 INLET HOSE CONNECTION The machine should be connected to the water mains using the new hose sets supplied NEVER reuse old hoses Be sure that the water inlet hoses are not folded broken or crushed The washer should be connected to the cold water supply as this gives the most efficient wash results Cold fill washing machines increase washing efficiency when using biological detergents because the enzymes work best at low temperatures PLEASE have only a qualified person install repair or replace parts on your machine CONNECTION TO THE COLD WATER MAINS 1 Connect the water inlet hose to the water supply only tighten the screw connection by hand N J JI I a S amp S 1 Connect the inlet hose to the drain outlet of the washing machine located on the upper right hand corner of the machine by turning it clockwise until it is tight Please check the rubber washer is present inside the inlet hose 3 By slowly opening the water tap before putting the machine into operation check that the connection is free of leaks WATER DRAIN CONNECTION e Be sure that the drain hoses are not folded twisted crushed or elo
31. only es Baumatic You will be mine Headquarters Baumatic Ltd Baumatic Buildings 6 Bennet Road Reading Berkshire RG2 0QX United Kingdom Sales Telephone 44 118 933 6900 Sales Fax 44 118 931 0035 Service Telephone 44 118 933 6911 Service Fax 44 118 986 9124 Spares Telephone 44 118 933 6922 Technical Advice Telephone 44 118 933 6933 E mail sales baumatic co uk technical baumatic co uk Http Internet site www baumatic com Environmental note This appliance is marked according to the European directive 2002 96 EC on Waste electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol on the product or on the documents accompanying the product indicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product o The
32. ot selected e Use this programme without a load ie any clothes in the drum e It is recommended that the cleaning cycle should be carried out once a month 23 a GUIDE FOR OTHER USEFUL PROGRAMMES DELAY START RESERVED WASHING Put the laundry into the drum Then close the Door In the detergent compartment put the powder into the main wash and prewash Step 1 sections See Diagram Page 9 Softener should be poured into the middle section of the compartment and be below MAX level Put the detergent into the pre wash section only if you want to add prewash e When you want to use bleach put it into the main wash section with detergent Press the Power button 2 e The LED shows this signal Select the programme using the programme selection dial If you press Start Pause button after pressing the Power button without selecting a Step 3 programme the NORMAL programme is selected as default programme e Select the Washing cycle Rinse time s Spin speed and water temperature by pressing by pressing the relevant buttons Press the DELAY START button The Time Delay LED will light up Step 4 Select the time you wish to delay your programme from one to twelve hours by pressing the appropriate button e The time displayed shows the time the selected programme will finish Press the Start Pause button Step 5 e If you carry out the above instructions correc
33. packaging materials that Baumatic uses are environmentally friendly and can be recycled o Please discard all packaging material with due regard for the environment Baumatic www baumatiece com
34. pen to the left Close the lower cover sS Cleaning the detergent case After a while detergent and fabric softeners leave a deposit in the drawer It should be cleaned from time to time with a jet of running water If necessary it can be removed completely from the machine by pressing the catch downwards and by pulling it out To facilitate cleaning the upper part of the fabric softener compartment can be removed ba IT T A E A 4 L I t j aas y a S Detergent can also accumulate inside the recess which should be cleaned occasionally with a brush Once you have finished cleaning replace the case and run a rinse A cycle without laundry 29 a REMOVING STAINS Stained heavily soiled or greasy items may need to be prewashed or soaked for best results Soaking helps remove protein type stains like blood milk or grass Prewashing helps loosen soil before washing PLEASE REFER TO CLOTHING CARE ADVICE ON MANFACTURERS LABEL Stain removal rules e Use warm water for soaking or prewashing stained laundry Hot water can set stains e Most stains are easier to remove when they are fresh e Before treating any stain find out what kind of stain it is how old the stain is what kind of fabric it is and whether the fabric is colorfast Check the care label Washing and drying can set some stains e Start with cold or warm water Hot water can set some stains When bleach is recommended use
35. poured into the middle section of the compartment and be below MAX level e Put the detergent into the pre wash section only if you want to add prewash e When you want to use bleach put it into the main wash section with detergent Press the Power button Sepe e The LED shows this signal Select the ECO WHITE programme using the programme selection dial If you press the Start Pause button after pressing the Power button without selecting a programme the NORMAL programme is selected as default programme e Main wash 3 times rinse 800 rpm spin speed and 60 C water Step 3 temperature are selected automatically e If you want to change the Washing programme Rinse time s Spin speed and water temperature select the programme you want by pressing the relevant buttons Press the Start Pause button Step 4 e The washing machine will start operating by locking the door and supplying water after sensing the amount of laundry automatically Note e If you want to change the programme setting during operation press the Start Pause button to hold the operation and then change the programme you want by pressing each corresponding button e Water temperature 40 C and 60 C are only selected e If you want to add the clothes during operation press Start Pause and Door unlock buttons then open the Door and put the clothes into the Drum Then close the Door a
36. r and supplying water Note If you start the memorised programme this data will be saved automatically e If you want to change the programme setting during operation press the Start Pause button to hold the operation and change to the programme you want by pressing each corresponding button e If you want to add the clothes during operation press the Start Pause and Door unlock buttons then open the Door and put the clothes into the drum Then close the door and press the Start Pause button again 22 11 DRUM CLEANING PROGRAMME Step 1 Put the laundry into the drum Then close the Door e If you want to clean the Drum slightly use this programme without bleach e If you want to clean the Drum thoroughly please use detergent only Step 2 Press the Power button e The LED shows only this signal Step 3 Select the DRUM CLEANING programme using the programme selection dial If you press the Start Pause button after pressing the Power button without selecting a programme the NORMAL programme is selected as default programme e Soak 2 times rinse 400 rom spin speed Cold water temperature and Cupboard dry condition are selected automatically Step 4 Press the Start Pause button e The machine will start operating by locking the Door and supplying water Note All programmes are not selectable except rinse time s e DELAY START is n
37. t supplied Error display e Did you connect the inlet hose and open the water tap e Is the inlet hose or the water tap frozen e Is the water supply shut off e Is there any foreign matter blocking up the inlet hose filter The machine will not drain Error display e Is the drain hose frozen or blocked up by dirt e Is the drain hose kinked or deformed Is the end of the drain hose immersed in water e Is there excessive dirt inside the drain filter e The machine will not spin Error display Are the clothes in the drum collected on one side Is the washer installed on an uneven floor or is the vibration serious e Is the door open The lamp 3 will light up in this case e Vibrating and too noisy Is the washer installed on an uneven floor e Have all the transit bolts been removed Note eif EH and 4 error mode are shown on PCB board please contact service centre SEE PAGE 34 35 31 Baumatic Ltd Conditions of guarantee Dear Customer Your new Baumatic appliance comes complete with a free 12 month guarantee covering both parts and labour costs resulting from defective materials or workmanship Baumatic also gives you the opportunity to automatically extend the guarantee period for a further 12 months at no extra cost giving an initial guarantee period of 24 months The extended guarantee period applies to England Scotland Wales and Northern Ireland only To qua
38. the Start Pause button e The machine will start operating by locking the Door and supplying water ONLY SPIN Step1 Put the laundry into the Drum and close the Door Step 2 Press the Power button P The LED shows only signal Select the SPIN CONDITION you want by pressing the SPIN button Step 3 e The NORMAL programme is selected automatically The water temperature is selected as Cold automatically Steb 4 Press the Start Pause button P e The machine will start operating by locking the Door 25 DRYER MEGA10WD Step 1 Put the laundry into the Drum and close the Door Press the Power button als e The LED shows this signal Select the DRY CONDITION you want by pressing the DRY button Step 3 As this button is pressed the dry condition is selected by Cupboard Very gt Time 30 1 00 1 30 OFF gt Low Temp gt Iron gt Cupboard Press the Start Pause button SIRRA e The machine will start operating by locking the Door Note Do not use detergent and softener e After finishing this programme 7357 7 is shown on PCB board alternately and the Easy Iron programme continues for thirty minutes only and automatically stops WOOL DELICATE and BLANKET programmes are not selectable with DRY Be wary of the temperature of the clothes if taking them out of the dryer immediately the drying cycle has fin
39. the the Door and supplying water Note e If you want to change the programme setting during operation press the Start Pause button to hold the operation and change to the programme you want to change by pressing each corresponding button e Water temperature 95 C is not selected in order to prevent clothes from being damaged e If you want to add clothes during operation press the Start Pause button and Door unlock buttons then open the Door and put the clothes into the Drum Then close the door and press the Start Pause button again 17 6 WOOL PROGRAMME Step 1 Put the laundry into the drum Then close the Door In the detergent compartment put the powder into the main wash section See Diagram Page 9 e Softener should be poured into the middle section of the compartment and be below MAX level e When you want to use bleach put it into the main wash section with detergent Step 2 Press the Power button The LED shows only this signal Step 3 Select the WOOL programme using the programme selection dial If you press the Start Pause button after pressing the Power button without selecting a programme the NORMAL programme is selected as the default programme e Main wash 2 times rinse 400 rpm spin speed and Cold water temperature are selected automatically e If you want to change the Washing programme Rinse time s and Spin
40. tly only the Time Delay and Lock LED s will be displayed Note e If you want to check the selected programme press the Start Pause button again e Before starting Time Delay Load laundry and close Door Put the detergent and fabric softener into the detergent compartment e The finishing time may vary from your selected time as it may be dependent upon your water supply and or selected water temperature WOOL and DELICATE and DRUM CLEANING programmes cannot be selected with select Time Delay e Adding clothes during Time Delay operation is not allowed 24 ONLY WASH Put the laundry into the Drum and put the detergent and softener into the detergent Step 1 compartment Then close the Door Step 2 Press the Power button e The LED shows this signal Step 3 Select the WASH CYCLE you want by pressing the WASH button e The NORMAL programme is selected automatically Step 4 Press the Start Pause button e The machine will start operating by locking the Door and supplying water ONLY RINSE Put the laundry into the Drum and put the detergent and softener into the detergent Step 1 compartment Then close the Door Step 2 Press the Power button e The LED shows this signal Step 3 Select the RINSE time s you want by pressing the RINSE button e The NORMAL programme is selected automatically Step 4 Press
Download Pdf Manuals
Related Search