Sun Blade 100 Product Notes
Contents
1. Sun 1394 Camera Support This information updates the Sun Blade 100 Getting Started Guide The Sun Blade 100 system supports the Sun Visual Collaboration Kit the Sun 1394 Camera and any Solaris ready 1394 compliant device Sun Blade 100 Specifications Tables A 1 and A 3 in Appendix A of the Sun Blade 100 Service Manual incorrectly list some of the system specifications Sun Blade 100 Product Notes September 2002 Tables A 1 and A 3 below list the correct system specifications and environmental requirements TABLE A 1 Sun Blade 100 System Physical Specifications Specification U S A Metric Height 4 6 in 11 8 cm Width 18 0 in 45 70 cm Depth 17 6 in 44 6 cm Weight 34 2 Ib 15 5 kg TABLE A 3 Sun Blade 100 System Environmental Requirements Environmental Operating Nonoperating Temperature 41 to 95 degrees F 4 to 140 degrees F 5 to 35 degrees C 20 to 60 degrees C Relative 40 to 80 noncondensing 30 to 90 noncondensing humidity at 95 degrees F 35 degrees C at 140 degrees F 60 degrees C Altitude 10 000 ft 3 km 40 000 ft 12 km DIMM Speed and Timing Section C 6 2 of Appendix C in the Sun Blade 100 Service Manual incorrectly lists the DIMM types and performance ranges The following information corrects the service manual The Sun Blade 100 uses PC133 compliant SDRAM DIMMs The motherboard can support up to 2 GBytes of memory with a 512 MByte DIMM in each of four slots The DIMMs must compl2. 3 IEC 950 1991 2nd Edition Am 1 2 3 4 Evaluated to all CB Countries CB Scheme Certificate No JPTUV 001881 Supplementary Information This product was tested and complies with all the requirements for the CE Mark S S Dennis P Symanski DATE Peter Arkless DATE Manager Compliance Engineering Ouality Manager Sun Microsystems Inc Sun Microsystems Scotland Limited 901 San Antonio Road MPK15 102 Springfield Linlithgow Palo Alto CA 94303 4900 USA West Lothian EH49 7LR Scotland United Kingdom Tel 650 786 3255 Tel 0506 670000 Fax 650 786 3723 Fax 0506 760011 11 12 Sun Blade 100 Product Notes September 2002
3. 100 system to help hold the PCI cards in place See FIGURE 1 FIGURE 1 Riser Board PCI Card Guide When installing long PCI cards make sure they seat properly into the guide Documentation Changes Preinstalled Software Notices Some preinstalled software was not listed in the Restoring the Preinstalled Software section of the Sun Blade 100 Getting Started Guide 8 Sun VTS SunVTS is the Sun online Validation Test Suite SunVTS is a comprehensive software diagnostic package that tests and validates hardware by verifying the connectivity and functionality of most hardware controllers devices and platforms You can find more information about Sun VTS in the following guides which are preinstalled on your system in the Sun Hardware Collection SunVTS 4 x User s Guide describes how to install configure and run the Sun 5 diagnostic software SunVTS Quick Reference Card provides an overview of how to use the SunVTS CDE interface m SunVTS 4 x Test Reference Manual provides details about each individual SunVTS test Sun PCi II The software driver for the Sun PCiTM II coprocessor card is preinstalled on your system The Sun PCi II card enables you to run Microsoft Windows applications on your Sun workstation concurrently with Solaris operating environment applications Workman This software enables your system CD ROM drive to play audio CDs This software is not supported by Sun Microsystems Inc
4. IS AND ALL EXPRESS OR IMPLIED CONDITIONS REPRESENTATIONS AND WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT ARE DISCLAIMED EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID Copyright 2002 Sun Microsystems Inc 4150 Network Circle Santa Clara California 95054 Etats Unis Tous droits r serv s Sun Microsystems Inc a les droits de propri t intellectuels relatants a la technologie incorpor e dans le produit qui est d crit dans ce document En particulier et sans la limitation ces droits de propri t intellectuels peuvent inclure un ou plus des brevets am ricains num r s http www sun com patents et un ou les brevets plus suppl mentaires ou les applications de brevet en attente dans les Etats Unis et dans les autres pays Ce produit ou document est prot g par un copyright et distribu avec des licences qui en restreignent l utilisation la copie la distribution et la d compilation Aucune partie de ce produit ou document ne peut tre reproduite sous aucune forme parquelque moyen que ce soit sans l autorisation pr alable et crite de Sun et de ses bailleurs de licence s il y ena Le logiciel d tenu par des tiers et quicomprend la technologie relative aux polices de caract res est prot g par un copyright et licenci par des fournisseurs de Sun Des parties de ce produit pourront tre d riv es des syst
5. PRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE A UAPTITUDE A UNE UTILISATION PARTICULIERE OU A L ABSENCE DE CONTREFA ON LD mom Ca Adobe PostScript Contents Installing a Previous Version of the Solaris Operating Environment 1 Checking Your Motherboard Part Number 1 Smart Card Reader Availability 2 Further Assistance 3 Software Changes 4 Installing the Solaris 8 7 01 Operating Environment 4 Setting the Default Console Display 4 Reinstalling the Solaris 8 10 00 or 8 1 01 Operating Environments and Patches 5 Power Management for the Sun Blade 100 When Using Solaris 8 10 00 or Solaris 81 01 Software 5 Hardware Changes 7 Riser Board PCI Card Guide 7 Documentation Changes 7 Preinstalled Software Notices 7 Sun 1394 Camera Support 8 Sun Blade 100 Specifications 8 DIMM Speed and Timing 9 Declaration of Conformity 10 Sun Blade 100 Product Notes September 2002 Sun Blade 100 Product Notes The following product notes summarize late breaking changes to Sun Blade 100 software hardware and documentation These changes became known after the product was released Installing a Previous Version of the Solaris Operating Environment If you intend to install a previous version of the Solaris software Solaris 8 10 00 software Solaris 8 1 01 software Solaris 8 4 01 software and your Sun Blade 100 motherboard is part number 375 3106 you need to follow a particular proced
6. hanges Installing the Solaris 8 7 01 Operating Environment The Solaris 8 7 01 operating environment has been preinstalled on your Sun Blade 100 system with all the necessary patches You can find more information about Solaris releases at http www sun com software solaris Setting the Default Console Display This information updates Appendix C of the Sun Blade 100 Service Manual If a PCI graphics card is installed such as the Sun Expert 3D Lite graphics accelerator the default monitor console switches to the installed PCI card You can override this behavior and set the on board M64 graphics device as the default monitor console 1 At the ok prompt type the following to display a list of the installed graphics devices ok show displays a pci lf 0 SUNW m64BG 13 b pci lf 0 pci 5 SUNW Expert 3D Lite l1 q NO SELECTION Enter Selection q to quit 2 Type the letter of the graphics card to select it as the default console display In this example type a to select the on board M64 graphics device Enter Selection q to quit a pci 1f 0 SUNW m64BR13 has been selected Type Y Control Y to insert it in the command line e g ok nvalias mydev Y 4 Sun Blade 100 Product Notes September 2002 3 Set the selected device as the console device by typing ok setenv output device y Control y Note You do not need to press the Shift key and you might not see
7. ion GUI 108909 12 108909 12 CDE dtsession updates 109354 14 109354 14 Opencard properties file 109695 03 Smart card core updates 109887 13 109887 13 109887 13 Internal card reader updates 110457 05 110457 05 110457 05 Note The smart card reader is not functional with any releases of the Solaris operating environment prior to the Solaris 8 7 01 software Sun Blade 100 Product Notes September 2002 v Installing the Patches 1 Check your Solaris 8 release date 2 cat etc release grep So Solaris 8 2 02 82858 7 088 SPARC In this example the release date is 2 02 2 Check your installed patches showrev p nawk print 2 sort This command lists all installed patches in ascending numeric order 3 If any patches are outdated or missing go to the SunSolve M web site at http www sunsolve sun com 4 Click the Patches link in the left column 5 Search for and download the latest versions of the patches Newer patches are signified by a higher dash number 6 Install the patches as superuser with the patchadd command For example patchadd M download directory 109887 13 110457 05 Where download directory is the directory to where you downloaded the patches Further Assistance If you are unable to use the smart card reader for your application after installing the reguired software contact your Sun service representative Software C
8. mes Berkeley BSD licenci s par l Universit de Californie UNIX est une marque d pos e aux Etats Unis et dans d autres pays et licenci e exclusivement par X Open Company Ltd Sun Sun Microsystems le logo Sun Sun PCi SunVTS Sun Blade SunSolve et Solaris sont des marques de fabrique ou des marques d pos es de Sun Microsystems Inc aux Etats Unis et dans d autres pays Toutes les marques SPARC sont utilis es sous licence et sont des marques de fabrique ou des marques d pos es de SPARC International Inc aux Etats Unis et dans d autres pays Les produits protant les marques SPARC sont bas s sur une architecture d velopp e par Sun Microsystems Inc L interface d utilisation graphique OPEN LOOK et Sun a t d velopp e par Sun Microsystems Inc pour ses utilisateurs et licenci s Sun reconnait les efforts de oa de Xerox pour la recherche et le d veloppment du concept des interfaces d utilisation visuelle ou graphique pour l industrie de l informatique Sun d tient une license non exclusive do Xerox sur l interface d utilisation graphique Xerox cette licence couvrant galement les licenci es de Sun gui mettent en place l interface d utilisation graphique OPEN LOOK et qui en outre se conforment aux licences crites de Sun LA DOCUMENTATION EST FOURNIE EN L TAT ET TOUTES AUTRES CONDITIONS DECLARATIONS ET GARANTIES EXPRESSES OU TACITES SONT FORMELLEMENT EXCLUES DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE Y COM
9. s for disabling Energy Star power management 6 Disabling Hard Drive Power Management When the system is in low power mode the hard drive eventually spins down to conserve power Later when you perform a task that accesses the hard drive the hard drive spins up again You might have to wait a few seconds for the hard drive to spin up to full speed If you find that the delay is inconvenient you can turn off Energy Star hard drive power management As superuser edit the etc power conf file to add the following line device thresholds dev dsk c0t0d0s0 always on Run the command usr bin pmconfig This procedure tells the power management framework to keep the hard drive powered up all the time regardless of drive usage You can completely turn off all power saving features of the workstation using the following procedure Disabling All System Power Management You can disable the Energy Star power management feature by using the dtpower application At the system prompt type usr openwin bin dtpower The dtpower application is displayed 2 Under the Current power saving scheme menu select Disabled 3 Press the OK button Sun Blade 100 Product Notes September 2 Hardware Changes Riser Board PCI Card Guide This information supplements the Sun Blade 100 Getting Started Guide and the Sun Blade 100 Service Manual A PCI card guide has been added to the riser board of the Sun Blade
10. sS amp SUN microsystems Sun Blade 100 Product Notes Sun Microsystems Inc 4150 Network Circle Santa Clara CA 95054 U S A 650 960 1300 Part No 816 1796 13 September 2002 Revision A Send comments about this document to docfeedback sun com Copyright 2002 Sun Microsystems Inc 4150 Network Circle Santa Clara California 95054 U S A All rights reserved Sun Microsystems Inc has intellectual property rights relating to technology embodied in the product that is described in this document In particular and without limitation these intellectual property rights may include one or more of the U S patents listed at ttp www sun com patents and one or more additional patents or pending patent applications in the U S and in other countries This document and the product to which it pertains are distributed under licenses restricting their use copying distribution and decompilation No part of the product or of this document may be reproduced in any form by any means without prior written authorization of Sun and its licensors if any Third party software including font technology is copyrighted and licensed from Sun suppliers Parts of the produet may be derived from Berkeley BSD systems licensed from the University of California UNIX is a registered trademark in the U S and in other countries exclusively licensed through X Open Company Ltd Sun Sun Microsystems the Sun logo Sun PCi SunVTS Sun Blade S
11. the Control y characters after you press the keys 4 Power off the system connect your monitor cable to the on board VGA connector at your system back panel and then power on the system Refer to the Sun Blade 100 Getting Started Guide for powering and cabling procedures Reinstalling the Solaris 8 10 00 or 8 1 01 Operating Environments and Patches This information supplements the Restoring the Preinstalled Software section in the Sun Blade 100 Getting Started Guide If you decide to reinstall the Solaris 8 10 00 or the Solaris 8 1 01 operating environment for any reason you must use a special set of installation CD ROMs in addition to the Solaris Media Kit To obtain the installation CD ROMs order the following part number from a Sun Authorized Reseller 595 6084 01 You can download and find information about software patches for both the Sun Blade 100 system and the Solaris operating environment at http www sunsolve sun com Power Management for the Sun Blade 100 When Using Solaris 8 10 00 or Solaris 8 1 01 Software This information supplements the Activating the System From Low Power Mode section in the Sun Blade 100 Getting Started Guide Hard drive and system power management are adjustable with the dtpower application in the Solaris 8 7 01 release However the power management features were not present in Solaris 8 10 00 and Solaris 8 1 01 releases The following two sections describe other method
12. unSolve and Solaris are trademarks or registered trademarks of Sun Microsystems Inc in the U S and in other countries All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International Inc in the U S and in other countries Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems Inc The OPEN LOOK and Sun Graphical User Interface was developed by Sun Microsystems Inc for its users and licensees Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry Sun holds a non exclusive license from Xerox to the Xerox Graphical User Interface which license also covers Sun s licensees viho implement OPEN LOOK GUIs and otherwise comply with Sun s written license agreement The Energy Star logo is a registered trademark ofEPA ars As an Energy Star partner Sun Microsystems Inc has determined that configurations of this 7 product that bear the Energy Star Logo meet the Energy Star guidelines for energy efficiency Use duplication or disclosure by the U S Government is subject to restrictions set forth in the Sun Microsystems Inc license agreements and as provided in DFARS 227 7202 1 a and 227 7202 3 a 1995 DFARS 252 227 7013 c 1 ii Oct 1998 FAR 12 212 a 1995 FAR 52 227 19 or FAR 52 227 14 ALT ID as applicable DOCUMENTATION IS PROVIDED AS
13. ure and configure certain patches as part of the installation Checking Your Motherboard Part Number Type the following command as a user of the system prtconf vp grep model head 1 If the command displays the part number 375 3106 for example model SUNW 375 3106 Follow the procedures described in Sun Blade 100 Motherboard Update and Sun PGX64 Patch Procedures 816 7660 You can find this document online at http www sun com documentation Click the following links Additional Hardware Documentation Desktop amp Workstation Sun Blade Workstations Sun Blade 100 You also need the Sun PGX64 Patch Kit Contact your Sun Microsystems representative for assistance If the command displays a different part number for example model SUNW 375 3092 You can install the previous version of the Solaris software as described in the Solaris documentation 2 Smart Card Reader Availability As stated in the Sun Blade 100 Getting Started Guide 806 3415 and the Sun Blade 100 Service Manual 806 3416 the smart card reader in the Sun Blade 100 is functional with the installation of newer Solaris operating environment software and software patches The required software patches are listed according to the system s Solaris release date TABLE1 Required Patches According to Solaris Release Date Patch Description Solaris 8 7 01 Solaris 8 10 01 Solaris 8 2 02 Smart card administrat
14. y with the following parameters TABLE C 6 DIMMs Performance Range Frequency tCK tRC tRAS tRP 133 Mhz 7 5 ns 67 5 ns 45 ns 20 ns Declaration of Conformity This information updates the Declaration of Conformity in the Sun Blade 100 Service Manual The correct Declaration of Conformity for the Sun Blade 100 system is as follows 10 Sun Blade 100 Product Notes September 2002 Declaration of Conformity Compliance Model Number 202 Product Name Sun Blade 100 EMC USA FCC Class B This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This equipment may not cause harmful interference 2 This equipment must accept any interference that may cause undesired operation European Union This equipment complies with the following requirements of the EMC Directive 89 336 EEC EN55022 1998 CISPR22 1997 Class B EN55024 1998 EN61000 4 2 4 kV Direct 8 kV Air EN61000 4 3 3 V m EN61000 4 4 1 0 kV AC Power Lines 0 5 kV Signal amp DC Power Lines EN61000 4 5 1 kV AC Line Line amp Outdoor Signal Lines 2 kV AC Line Gnd 0 5 kV DC Power Lines EN61000 4 6 3 V EN61000 4 8 1 A m EN61000 4 11 Pass EN61000 3 2 1995 w Am 1 2 Pass EN61000 3 3 1995 Pass Safety This equipment complies with the following requirements of Low Voltage Directive 73 23 EEC EC Type Examination Certificates EN60950 1992 2nd Edition Am 1 2 3 4 11 TUV Rheinland Certificate No 5
Download Pdf Manuals
Related Search