Siemens Fujitsu SCENIC D (D810E
Contents
1. A26361 D1170 Z120 5 7419 English 18 Glossary Glossary The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations Not all technical terms and abbreviations listed here are valid for the described system board Industrial Standard Architecture Power Management Interface Attachment Central Processing Unit Communication Network Riser C RIMM Continuity Rambus Inline Memory Module DIMM Dual Inline Memory Module Error Correcting Code FDC EEPROM Electrical Erasable Programmable Read Only Memory Floppy Disk Controller First In First Out FIFO First In First Out Front Side Bus Hub Accelerator EC Inter Integrated Circuit Instantly Available Power Managed Desktop PC Design 1 O Controller Hub Intelligent Drive Electronics IPSEC Internet Protocol Security 14 English LAN LSA MCH MMX P64H Interconnect PXE RAM Analogue Converter Rambus Dynamic Random Access Memory RIMM s i Rambus Inline Memory Module RTC Real Time Clock SB Soundblaster SDRAM Synchronous Dynamic Random Access Memory Access Memory Br ee SIMD Streaming Mode Instruction SVGA i eee Super Video Graphic Adapter USB Bez Universal Serial Bus Video Graphic Adapter Wake On LAN RDRAM A26361 D1170 Z120 5 74192. Technisches Handbuch Technical Manual co FUJ ITSU COMPUTERS SIEMENS Sie haben technische Fragen oder Probleme Wenden Sie sich bitte an e _ Ihren zust ndigen Vertriebspartner Ihre Verkaufsstelle Weitere Informationen finden Sie in den Handb chern Sicherheit und Ergonomie Aktuelle Informationen zu unseren Produkten Tipps Updates usw finden Sie im Internet http www fujitsu siemens com Are there any technical problems or other questions you need clarified Please contact e _ your sales partner e your sales outlet You will find further information in the manuals Safety and Ergonomics The latest information on our products tips updates etc can be found on the Internet under http www fujitsu siemens com Dieses Handbuch wurde auf Recycling Papier gedruckt This manual has been printed on recycled paper Ce manuel est imprim sur du papier recycl Este manual ha sido impreso sobre papel reciclado Questo manuale stato stampato su carta da riciclaggio Denna handbok r tryckt p recyclingpapper Dit handboek werd op recycling papier gedrukt Herausgegeben von Published by Fujitsu Siemens Computers GmbH Bestell Nr Order No A26361 D1170 Z120 1 7419 Printed in the Federal Republic of Germany AG 0602 06 02 A26361 D1170 Z120 1 7419 Deutsch English Mainboard D1170 Technisches Handbuch Technical Manual Ausgabe Juni 2002 June 2002 edition
3. 4 1 3 Location bank 2 for main memory 10 English A26361 D1170 Z120 5 7419 Add on modules Installing and removing processors gt Pull the lever in the direction of the arrow 1 and lift it as far as it will go 2 Remove the old processor from the socket 3 gt Insert the new processor in the socket so that the angled corner of the processor matches the coding on the socket A with regard to the position 4 The angled corner of the processor may be covered by the heat sink In this case let yourself be guided by the marking in the rows of pins on the underside of the processor gt Push the lever back down so that it snaps into place A26361 D1170 Z120 5 7419 English 11 Add on modules Upgrading main memory These slots are suitable for memory modules with 16 32 64 128 and 256 Mbyte of the DIMM format Therefore the memory capacity of one component on the memory module may not exceed 128 Mbit 16 MB Memory modules with different memory capacities can be combined You may only use unbuffered 3 3 V memory modules Buffered memory modules are not supported SDRAM memory modules must be designed for a clock frequency of 100 MHz meets PC100 specification Installing a memory module gt Push the holders on each side of the memory compartment outwards gt Insert the memory module into the location Watch the coding of the memory module when doing so gt Atthe same time flip the latera
4. Intel Pentium und Celeron sind eingetragene der Intel Corporation USA Microsoft MS MS DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation PS 2 und OS 2 Warp sind eingetragene Warenzeichen von International Business Machines Inc Alle weiteren genannten Warenzeichen sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen Inhaber und werden als gesch tzt anerkannt Copyright Fujitsu Siemens Computers GmbH 2002 Alle Rechte vorbehalten insbesondere auch auszugsweise die der bersetzung des Nachdrucks der Wiedergabe durch Kopieren oder ahnliche Verfahren Zuwiderhandlungen verpflichten zu Schadenersatz Alle Rechte vorbehalten insbesondere f r den Fall der Patenterteilung oder GM Eintragung Lieferm glichkeiten und technische Anderungen vorbehalten Dieses Handbuch wurde erstellt von cognitas Gesellschaft f r Technik Dokumentation mbH www cognitas de Intel Pentium and Celeron are registered trademarks of Intel Corporation USA Microsoft MS MS DOS and Windows are registered trademarks of Microsoft Corporation PS 2 and OS 2 Warp are registered trademarks of International Business Machines Inc All other trademarks referenced are trademarks or registered trademarks of their respective owners whose protected rights are acknowledged All rights including rights of translation reproduction by printing copying or similar methods even of parts are reserved Offenders will be liable
5. Z120 5 7419 Features Features e System board in micro ATX format e Intel Celeron processor with 66 MHz 100 MHz Front Side Bus for PGA 370 socket and Pentium III with 100 133 MHz Front Side Bus for PGA 370 socket Intel Celeron and Pentium Ill processors support MMX technology and Intel Streaming SIMD Extensions The size and frequency of first level cache and second level cache are dependent upon the processor used e Intel chipset 810E consisting of GMCH 82810E ICH 82801 and FWH82802 e AC 97 Audio Codec internal Stereo CD In Stereo AUX In external Mono Micro In Stereo Line In Game Midi Port Stereo Line Out max 2 x 0 5 W 8 Q e 2DIMM slots for 16 to 512 Mbyte main memory SDRAM memory modules meet the PC100 specification without ECC e Flash BIOS e Energy saving functions ACPI and APM Switching on off standby mode suspend mode via on off switch Switching on off via software Wake on RTC Wake on LAN Wake on PCI Cards e Security functions System Setup and Keyboard password parallel and serial ports can be deactivated Cover monitoring cover monitoring reports when the cover has been opened without authorisation Write protection for floppy disk drive Boot hard disk virus warning function A Flash BIOS and EEPROMs on the memory modules virus protection function e 4 PCI slots PCI slots support 3 3 V main voltage e IDE hard disk controller connected to PCI
6. bus for up to four IDE drives e g IDE hard disk drives ATAPI CD ROM drives The IDE hard disk controller are ATA33 66 ultra DMA capable and support PIO modes 0 4 e Floppy disk drive controller possible formats 720 KB 1 44 MB 2 88 MB e The system board supports booting from a 120 MB IDE floppy disk drive e 2D 3D graphics processor 24 bit 230 MHz RAMDAC e Monitor connector Sub D A26361 D1170 Z120 5 7419 English 3 Features e 1external parallel interface ECP and EPP compatible e 1external serial port 160550 compatible with FIFO This port does not support the ring indicator signal e 1 internal chipcard reader interface As an alternative the chipcard reader interface can also be used as a second serial port 16C550 compatible with FIFO This port does not support the ring indicator signal e 1 internal WOL interface e 2external PS 2 interfaces for keyboard and mouse e 2external USB ports e Real time clock calendar with integrated battery backup 4 English A26361 D1170 Z120 5 7419 Features Interfaces and connectors ess 0000000000 0000000000 DIMM 2 DIMM 1 ka PCI 3 9a9b9c 12 PS 2 mouse port 5 Serial port 1 2 PS 2 keyboard port 6 Parallel port 3 2 USB port 2 7 VGA port 4 USB port 1 8 Game Midi
7. for damages All rights including rights created by patent grant or registration of a utility model or design are reserved Delivery subject to availability Right of technical modification reserved This manual was produced by cognitas Gesellschaft f r Technik Dokumentation mbH www cognitas de Contents Settings with switches Hecovering System BIOS switch 2 A26361 D1170 Z120 5 7419 Introduction Depending on the configuration chosen some of the hardware components described may not be available on your system board You will find further information in the BIOS Setup description Further information about drivers is provided in the readme files on the hard disk on the supplied drivers diskettes on the Drivers amp Utilities or on the ServerStart CD Notational conventions The meanings of the symbols and fonts used in this manual are as follows Pay particular attention to text marked with this symbol Failure to observe this warning endangers your life destroys the device or may lead to loss of data D Supplementary information remarks and tips follow this symbol Text which follows this symbol describes activities that must be performed in the order shown This symbol indicates that you must enter a blank space press the Space Bar at this point J This symbol indicates that you must press the Enter key Text in this typeface indicates screen outputs Text in this bold typeface indica
8. l holders upwards until the memory module snaps in place Removing a memory module Flip the holders to the right and left of the location outwards gt Pullthe memory module out of its location 12 English A26361 D1170 Z120 5 7419 Add on modules Installing network board with WOL gt Install the network board as described in the operating manual for your unit gt Push the WOL cable onto the WOL plug connector of the system board auxiliary voltage of at least 1 A If the system board was not already incorporated in a device when you bought it you must check whether your power supply can provide the auxiliary voltage D To use the WOL functionality of a network board the power supply must provide a 5 V You may find further information in the supplied description of the network board Replacing the lithium battery N Incorrect replacement of the lithium battery may lead to a risk of explosion The lithium battery must be replaced with an identical battery or a battery type recommended by the manufacturer CR2032 Do not throw lithium batteries into the household waste They must be disposed of in accordance with local regulations concerning special waste Ensure that you insert the battery the right way round The plus pole must be on the top gt Liftthe contact 1 a few millimetres and remove the lithium battery from its socket 2 gt Inserta new lithium battery of the same type into the socket 3
9. port 9a Audio Line Out 9b Audio Line In 9c Audio Micro In A26361 D1170 Z120 5 7419 English 5 Features ooopoocooo 0005000000 DIMM 2 ac i lmj Chipcard reader port optional or serial port 2 Power supply IDE drives 3 and 4 secondary Floppy Disk Drive Connector for control panel and loudspeaker IDE drives 1 and 2 primary E ll C140 rn 6 rc a PI eg 7 Fan 2 e g for the processor 8 Wake On LAN 9 CD audio input 10 AUX audio input 11 2 Fan 1 e g for the processor 12 Cover monitoring The components and connectors marked are not necessarily present on the system board Hard disk connection An ultra ATA 66 hard disk must be connected with a cable especially designed for the ATA 66 mode gt Connect the end of the cable marked with blue to the system board 6 English A26361 D1170 Z120 5 7419 Features PCI bus interrupts The following table shows which PCI bus interrupts are assigned on the system board PCI bus interrupt Component on system board PCI bus slot 1 PCI bus slot 2 PCI bus slot 3 PCI bus slot 4 USB controller Graphics processor SMBus AC 97 Screen resolution Depending on the operating system used the screen resolutions in the following table refer to the system boa
10. rd screen controller If you are using an external screen controller you will find details of supported screen resolutions in the Operating Manual or Technical Manual supplied with the controller Screen resolution Refresh rate Hz Horizontal Max number of rate kHz colours 640x480 31 5 43 3 256 640x480 31 5 43 3 65536 640x480 31 5 43 3 16777216 800x600 35 1 53 7 256 800x600 35 1 53 7 65536 800x600 35 1 53 7 16777216 1024x768 48 8 68 7 256 1024x768 48 8 68 7 65536 1024x768 48 8 68 7 16777216 1152x864 54 4 76 9 256 1152x864 54 4 76 9 65536 1152x864 54 4 76 9 16777216 1280x1024 64 0 91 1 256 1280x1024 64 0 91 1 65536 1280x1024 64 0 91 1 16777216 1600x1200 75 0 93 8 256 no 16 colour mode Horizontal values tolerance 0 3 kHz A26361 D1170 Z120 5 7419 English 7 Settings with switches Settings with switches se El esesessese 0000000000 3323 593 c DIMM 2 ac 3 DIMM 1 UL eee PC 3 een es Li Switch 1 2 must be set to off Switch 3 Write protection for floppy disk Switch 2 System BIOS recovery Switch 4 must be set to off n The clock frequency of the processor is set automatically 8 English A26361 D1170 Z120 5 7419 Settings with switches Recovering System BIOS switch 2 Switch 2 enables recovery of the old sys
11. tem BIOS after an attempt to update has failed To restore the old system BIOS you need a Flash BIOS Diskette please call our customer service centre On The System BIOS executes from floppy drive A and the inserted Flash BIOS Diskette restores the System BIOS on the system board Off Normal operation default setting Write protection for floppy disks switch 3 Switch 3 is used to define whether floppy disks can be written or deleted in the floppy disk drive To write and delete floppy disks the write protection in BIOS Setup must be disabled in menu Security the field Diskette Write must be set to Enabled On The floppy disk drive is write protected Off Floppy disks can be read written and deleted default setting A26361 D1170 Z120 5 7419 English 9 Add on modules Add on modules Exit Suspend mode switch off the device and remove the power plug from the mains supply before carrying out any of the procedures described in this chapter Even when you have switched off the device parts e g memory modules AGP and PCI extension boards are still supplied with power All PCI slots have bus master capability and support 3 3 V 0000000000 0000000000 DIMM 3 DIMM 1 PCI 1 Socket for processor with heat sink 4 Lithium battery 2 Location bank 1 for main memory 5 PCI slots 2 3
12. tem board There is a danger of burns replacement of system expansions Information on which system expansions you can i The warranty is invalidated if the device is damaged during the installation or use is available from your sales outlet or the customer service centre Information about boards To prevent damage to the system board or the components and conductors on it please take great care when you insert or remove boards Take great care to ensure that extension boards are slotted in straight without damaging components or conductors on the system board or any other components for example EMI spring contacts Be especially careful with the locking mechanisms catches centring pins etc when you replace the system board or components on it for example memory modules or processors Never use sharp objects screwdrivers for leverage Boards with electrostatic sensitive devices ESD are identifiable by the label shown When you handle boards fitted with ESDs you must under all circumstances observe the following points e You must always discharge static build up e g by touching a grounded object before working e The equipment and tools you use must be free of static charges e Remove the power plug from the mains supply before inserting or removing boards containing ESDs e Always hold boards with ESDs by their edges e Never touch pins or conductors on boards fitted with ESDs 2 English A26361 D1170
13. tes the entries you make via the keyboard Text in italics indicates commands or menu items Quotation marks indicate names of chapters or terms Important notes Store this manual close to the device If you pass the device on to third parties you should pass this manual on with it i Be sure to read this page carefully and note the information before you open the device You cannot access the system board components without first opening the device How to dismantle and reassemble the device is described in the Operating Manual accompanying the device Please observe the safety information provided in the Important notes chapter in the device s operating manual Incorrect replacement of the lithium battery may lead to a risk of explosion It is therefore essential to observe the instructions in the Add on modules Replacing the lithium section A26361 D1170 Z120 5 7419 English 1 Important notes The shipped version of this board complies with the requirements of the EEC directive 89 336 EEC Electromagnetic compatibility Compliance was tested in a typical PC configuration When installing the board refer to the specific installation information in the Operating Manual or Technical Manual for the receiving device Connecting cables for peripherals must be adequately shielded to avoid interference Components can become very hot during operation Ensure you do not touch components when making extensions to the sys
Download Pdf Manuals
Related Search