Kobe RA3836SQ Under Cabinet Range Hood
Contents
1. lights or any type of appliance Open all doors and windows to disperse the gas If you still smell gas call the Gas Company and Fire Department right away CAUTION 1 For general ventilation use only Do not use to exhaust hazardous or explosive materials and vapors 2 To reduce the risk of fire use only metal ductwork 3 Follow the heating equipment manufacturer s guideline and safety standards such as those published by the National Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE and code authorities 4 Activating any switch on may cause ignition or an explosion WARNING T amp ELECTRICAL SHOCK HAZARD Can result in serious injury or death Disconnect appliance from electric power before servicing If equipped the fluorescent light bulb contains small amounts of mercury which must be recycled or disposed of according to Local State and Federal Codes 5 Must keep all material for returns or refunds Range Hood Box Duct Cover Box Sold Separately A KOBE Range Hood F KOBE Duct Cover Model No RA1020DC B Warranty Registration Card G Screws Package C Instructions Manual H Duct Cover Mounting Bracket D Oil Containers Round 1 Hood Mounting Bracket E Oil Containers Oval F Inner Duct Cover Outer Duct Cover B 3 16 x 3 8 mm 6 pcs 4 x 8 mm 8 pc2. Failure to do this could result in the carrier refusing to honor your claim The carrier will furnish you with necessary forms for filing a claim DAMAGES CAUSED DURING TRANSIT ARE NOT COVERED UNDER OUR WARRANTY PLEASE INSPECT CONTENTS OF PACKAGE S CAREFULLY UPON RECEIVING We must be notified in writing of any damages and or missing parts within the allocated days upon receipt of package s Contact your local KOBE dealer or distributor or call KOBE for the time limit CLAIMS WILL NOT BE ACCEPTED AFTER THE ALLOCATED DAYS NOTE ITEMS WERE THOROUGHLY TESTED AND CAREFULLY PACKED IN OUR FACTORY Products must be returned in good working condition with ALL original parts and documentation packed in ALL original cartons fillers and shipping cartons A restocking fee of 25 will be charged for all approved return s EXCHANGES OR RETURNS MAY NOT BE ACCEPTED IF ANY PACKAGING IS MISSING MAKE SURE TO INSPECT THE HOOD FOR DAMAGES AND DEFECTS BEFORE INSTALLATION Appearance flaws of the hood found after installation and not affecting hood performance is not covered under our warranty for returns or exchanges Service visits not covered under warranty will carry a service charge A Before Installation Return for exchange or refund please see above for acceptable returns B After Installation NO exchange or refund 19 KOBE Range Hoods Inc warrants all products manufactu
3. Figure 2 Measure and create access opening for electrical wires under the cabinet ELBOW Figure 1 Figure 2 Hood Installation CAUTION If required to move the cooking range to install the hood turn off the power on an electric range at the main electrical box SHUT OFF THE GAS BEFORE MOVING A GAS RANGE 1 Puncture the knockout holes Refer to Figure 3 Figure 3 2 NOTE Be careful when using electrical screwdriver damage the hood might occur Unscrew the six screws on the bottom casing Remove the bottom casing as shown on Figure 4 If necessary arrange the electrical wire to run through the 1 diameter hole the hood 3 Using references on Table 1 and measurement on page 16 center the hood in place beneath the cabinet and flush with the front of the cabinet Refer to Figure 5 Figure 4 Figure 5 4 Draw electrical wires through cabinet access opening 5 Place screws not provided into the exact center of each hole Make sure all screws are in place before tightening screws CAUTION MAKE SURE THE HOOD IS SECURE BEFORE RELEASING Ductwork Installation 6 Use aluminum or steel pipe to connect the plastic exhaust on the hood to the ductwork above Use duct tape to make all joints secure and air tight Wiring to Power Supply 7 Connect the electrical wires necessary to hide the electrical wire connections push wires back into the hood Access the wire connections underneath the hood by remo
4. manufactured tested and inspected to the standards required by KOBE Range Hoods PLEASE MAIL IN YOUR WARRANTY REGISTRATION CARD AND PROOF OF PURCHASE TO KOBE Range Hoods Inc 4934 Walnut Grove Avenue Suite 202 oan Gabriel CA 91776 RECORD THE FOLLOWING INFORMATION FOR YOUR RECORD Model No Serial No Purchased Date Purchased From IMPORTANT PLEASE KEEP A COPY OF YOUR SALE RECEIPT OR INVOICE HANDY WHEN REQUESTING FOR SERVICE 22
5. 39 0 47 0 QuietMode Low High 330 480 720 1 0 2 8 4 8 House Test Static Pressure 0 One sone is equivalent to sound of a refrigerator at 40 decibels Specifications information is subject to change without notice 14 5 1 8 130 MEASUREMENTS amp DIAGRAMS All inch measurements are converted from millimeter Inch measurements are estimated All measurements in are millimeters FOR UNDER THE CABINET 30 Knockout Holes A 36 Knockout Holes A amp B FOR STAND ALONE WITH OPTIONAL DUCT COVER 44 3 4 1136 MAX Hood Mounting Bracket 3 4 20 v6 9L LL 4 1 16 104 4 1 16 104 9 3 8 238 15 PARTS LIST MODEL NO RA3830SQ RA3836SQ NO DESCRIPTION MODEL SIZTE PARTNO 1 6 Round Plastic Exhaust C1 0505 0001 2 Capacitor 1227 1 040 02 44 3 Transformer Light 127 C1 0402012040 2 4 Screw 4x6mm 10708 0000 2 5 j Scew Ax6mm 12 C1 0708001 2 6 PowerCord 127 C1 0406001200 amp X 7 Scew TS4x18mm A A A4A 21C1 0708000 8 Plastic Plate 72 1 557 201 2 2 OS QUOTE 1065380 10 Screw 3167578 7 15 0704 04 Halogen Light 12V 20W Max 10403 0101 12 Air Chamber 15 Turbine Impeller Left C1 0251 0092 01 Lx 16 Turbine Impeller Right 12 Cf 0251 00202 2 17 Oil
6. 4x8 mm screws provided as shown on Figure 14 Fasten outer duct cover to plastic plate on the hood with four 4x8 mm screws provided 9 Attach Together Figure 14 Wiring to Power Supply ASAFETY WARNING RISK OF ELECTRICAL SHOCK THIS RANGE HOOD MUST BE PROPERLY GROUNDED MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES BEFORE CONNECTING WIRES SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY Connect three wires black white and green to house wires and cap with wire connectors Connect according to color black to black white to white and green to green Test the operation of the hood before moving on to next step Make sure power is supplied to the hood Install Accessories 10 Place the oil container round into keyhole under each safety screen Turn clock wise until firmly in place Refer to Figure 15 11 Slide oil container oval into plastic slot behind each safety screen Refer to Figure 16 Figure 15 Figure 16 Final Assembly 12 Turn power ON in control panel Check all lights and blower operation 13 Make sure to leave this manual for the homeowner 10 INSTRUCTIONS This KOBE hood is equipped with four switch control two powerful centrifugal turbine impellers with safety screens two bright 12 volt 20 watt halogen lights an
7. KORBE KOBE Brand Range Hood Model RA3830SQ RA3836SQ RA 038 SERIES 5 HEIGHT INSTALLATION INSTRUCTIONS AND OPERATION MANUAL READ AND SAVE THESE INSTRUCTIONS CONTENTS Important Safety InstrucliOris oues soa once zo trac 1 Components 7 2 77 2 3 ON PEE ESENTIUM 4 Under the CabpinetdTnstallalioh 2 route da Dub meris 5 Stand Alone 2 2 2 72 7 2 2 2 22 2 2 8 o 11 12 SD SCINGCAUONS 14 Measurements amp Diagralmis 15 PT PECES 16 Gres MBIe on E DO OT LIMES 18 LTS GIANNI Mic ba Le lcve e ig M PLI 19 VUES IRE IRI PEPERIT EIE 20 V 22 READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES O 221547 IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THIS SECTIO
8. N CAREFULLY BEFORE INSTALLATION WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY OBSERVE THE FOLLOWING 1 Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards including fire rated construction 2 When cutting or drilling into wall or ceiling be careful not to damage electrical wiring or other hidden utilities 3 Ducted fans must be vented to the outside a Before servicing or cleaning unit open the light panel and SWITCH POWER OFF AT SERVICE PANEL b Clean fan optional filter and grease laden surfaces frequently To reduce the risk of fire and to disperse air properly make sure to vent air outside DO NOT vent exhaust air into wall spaces attics crawl spaces or garages NOTE This warranty is invalid without an authorized agent s receipt or if unit is damaged due to misuse poor installation improper use mistreatment negligence or any other circumstances beyond the control of KOBE RANGE HOODS authorized agents Any repair carried out without the supervision of KOBE RANGE HOODS authorized agents will automatically void the warranty KOBE RANGE HOODS will not be held responsible for any damages to personal property or real estate or any bodily injuries whether caused directly or indirectly by the range hood WARNING TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF ARANGE TOP GREASE FIRE Keep fan filter if a
9. OR SERVICING Preparation before Installation NOTE TO AVOID DAMAGE TO YOUR HOOD PREVENT DEBRIS FROM ENTERING THE VENT OPENING Decide the ductwork and locations Refer to Figure 8 Decide the location of the venting pipe from the hood to the outside straight short venting run will allow the hood to perform more efficiently Try to avoid as much transitions elbows and long run as possible This may reduce the performance of the hood Use duct tape to seal the joints between pipe sections necessary prepare back wall frame with cross framing lumber for secure installation Using references on Table 2 and measurement on page 16 decide the level of the lumber Refer to Figure 9 WALL STUDS DUCT COVER Figure 8 Figure 9 Hood Preparation before Installation Temporarily wire the hood to test for proper operation before installing Peel protective film off the hood and the duct cover if any Attach the hood mounting bracket behind the hood with 3 16x3 8 mm screws provided as shown on Figure 10 Hood Installation CAUTION If required to move the cooking range to install the hood turn off the power on an electric range at the main electrical box SHUT OFF THE GAS BEFORE MOVING A GAS RANGE 1 If necessary attach two rubber stands provided with two 4x8 mm screws provided to the back of the hood Using references on Table 2 and measurement on page 16 decide the le
10. Tunnel Seal 10200 1 Cf052031 002 18 jOiTume 14022 1 502009 22 19 Bottom Casing B101 0330 09 RA3836SQ B101 0392 09 24 C1 0503 0101 Safety Screen Screw 1 0705 0001 1 0704 0004 1 0251 0001 screw 3 16 x 5 8 Impeller Plastic Cover 0405 0511 C1 0405 0213 C1 0511 0211 C1 0708 0006 ee 7 25 On Off Switch 1 0405 0211 Im gj E 4 Optional Duct Cover NO DESCRIPTION MODEL SIZE PART NO Screw 3 16 x 3 87 T61 0707 0004 BENE Hood Mounting Bracket C1 0221 0330 35 RoundHeadScew TS4x8mm A 10708 0008 36 Round Head Screw TS 4 x 8 mm C1 0708 0006 37 Duct Cover Mounting Bracket 1 1 50203002 2 383650 MODEL 8 3059 17 CIRCUIT DIAGRAM MODEL No RA3830SQ RA3836SQ og ae ENSE e 5 BR iD L 22 P w w U Ak a TRANSFORMER BL BR Y BR W BK BK W KEY CODE Blue Black Brown Red White Green Yellow Orange High Low QuietMode Halogen Light 18 DISCLAIMER 1 CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT REQUEST NAME AND SIGNATURE OF THE CARRIER S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM Upon acceptance of items owner assumes responsibility for its safe arrival Damages should be reported to carrier and a claim filed
11. d four oil containers The four control switches are Light Control Speed Control QuietMode Control and the Power Control On Off Refer to Figure 17 Figure 17 Light Control 5 Power Control Speed M ode Control Low High Turn On Press Power Control switch to turn on the power Press the Speed Control Low Off High or QuietMode Control to select the desired speed Once the Power Control is turned on the previous switch selections will turned on Press the QuietMode Control to turn on QuietMode Speed Control will automatically be disabled when QuietMode is turned on Press Light Control switch to turn halogen lights on Turn Off Press the Power Control switch to turn off all power Note The Power Control switch is the main power controller If disable QuietMode speed will revert to its prior Speed Control 11 MAINTENANCE CAUTION NEVER PUT YOUR HAND INTO THE AREA HOUSING THE FAN WHILE THE FAN IS OPERATING For the optimal level of operation clean the range hood surface safety screens and oil containers regularly To Clean Hood Surface CAUTION NEVER USE ABRASIVE CLEANERS PADS OR CLOTHS Regular care will help preserve its fine appearance 1 2 3 4 5 6 Use only mild soap or detergent solutions Dry surfaces using soft cloth If hood looks splotchy stainless steel hood use an orange base cleaner to clean the surface of the hood Avoid c
12. e the safety screen screw and slide the safety screen out Wash with warm soapy water Dry completely before returning into place Top rack dishwasher safe 12 To Replace Light Bulb CAUTION HALOGEN LIGHT UNIT MAY BE HOT WAIT UNTIL UNIT IS COOL 1 2 3 4 5 Make sure all control switches are off and range hood is unplugged Use a flat head screwdriver to pop out the protective covering as shown on Figure 18 Gently pull out the defective light bulb and discard Light bulbs should be 12V 20W maximum Refer to Figure 19 Push bulb securely into light socket Replace protective cover Plug in range hood Figure 18 Figure 19 13 SPECIFICATIONS MODEL SIZE COLOR VOLTAGE NUMBER OF MOTORS DESIGN FAN TYPE EXHAUST CONTROLS HALOGEN LIGHTS HOOD DIMENSION W x D x H OPTIONAL ACCESSORIES W x D x H WEIGHT SPEED Air Capacity cfm oone RA3830SQ 30 8 3650 36 430 Commercial Grade Stainless Steel 120V 60Hz 2 18 Gauge Seamless Twin Turbine Impeller 6 Round Three Speed QuietMode Low amp High 12V 20W x 2 RA3830SQ 29 3 4 x 20 1 2 x 5 1 8 RA3836SQ 35 1 4 x 20 1 2 x 5 1 8 1 Two Piece Adjustable Duct Cover RA1020DC 10 5 8 x 9 1 8 x 20 5 8 39 5 8 2 30 Stainless Steel Back Panel SSP30 30 x 1 10 x 32 3 36 Stainless Steel Back Panel SSP36 36 x 1 10 x 32 Net Gross RA3830SQ 37 0 43 0 RA3836SQ
13. eriod applicable C for failure of light bulbs d for physical damage e for surfaces damaged by use of improper chemical cleaning agents f if the appliance has been i subject to misuse abuse negligence accident incorrect installation or failure to follow the operating instructions ii connected to improper inadequate or faulty electricity service or exhaust ducts or flues or operated using incorrect or contaminated lubricants iii installed maintained or operated otherwise than in accordance with the instructions furnished by KOBE Range Hoods including the improper use of detergents bleaches or cleaners g for damage to range hood during transit delivery installation or removal h for damage by or resulting from attempted repairs conducted by anyone other than our Authorized Service Agent 20 3 The purchaser shall be responsible for expenses involved making range hood readily accessible for servicing and where the range hood is installed outside the main sales territory of the retailer or service territory of the nearest approved KOBE Range Hoods Agent as applicable for any traveling expenses and any costs of transporting the range hood or parts thereof to and from the dealer or Service Agent 4 The purchaser must produce proof of purchase together with this warranty certificate when making the claim 5 Damages caused during shipment are not covered under our warranty CONSEQUENTIAL DAMAGE T
14. he warrantor is not responsible for any consequential damage SOME STATES DO NOT ALLOW THE EXCLUSION OF CONSEQUENTIAL DAMAGE SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU IMPLIED WARRANTIES STATE LAW Any implied warranties including the implied warranty of merchantability and fitness for purpose imposed on the sale by the laws of the state of sale are limited to two year from the date of original purchase Some states do not allow limitations on the duration of implied warranties This warranty gives you specific legal rights and may also have rights which vary from state to state SERVICE For service contact KOBE Range Hoods Inc 4934 Walnut Grove Avenue Suite 202 san Gabriel CA 91776 U S A Tel 626 309 1356 Fax 626 309 1366 Email customerservice koberangehoods com www KobeRangeHoods com 21 PRODUCT REGISTRATION Register Your Product Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable Keep proof of purchase original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner is protected until expiration of the original purchaser s warranty See warranty section for complete warranty coverage information This appliance has been
15. leaner to get on the control switches Only spread a light coating over the surface of the hood and leave on for a few minutes do not leave on too long or this may cause damage to hood finish Use soft towel to wipe off the cleaning solution gently rubs any stubborn spots Use a slightly damp towel to get rid of any cleaning solution Use dry soft towel to dry the hood To bring the glow back into a stainless steel finish use a stainless steel cleaner DO NOT allow deposits to remain for long periods of time DO NOT use ordinary steel wool or steel brushes Small bits of steel may adhere to the surface causing rust DO NOT allow salt solutions disinfectants bleaches or cleaning compounds to remain in contact with stainless steel for extended periods Many of these compounds contain chemicals which may be harmful Rinse with water after exposure and wipe dry with a clean cloth To Clean Oil Containers Safety Screens and Impellers CAUTION DRAIN OIL CONTAINER BEFORE OIL CAN OVERFLOW 1 2 3 Normal Cleaning Turn on high speed and spray a mild degreaser into the fan Liquid residue will accumulate in the oil containers Cleaning Oil Containers Remove the oil container round by turning counterclockwise for cleaning Remove the oil container oval by sliding forward for cleaning Wash with warm soapy water Dry completely before returning into place Top rack dishwasher safe Cleaning Safety Screens Remov
16. ny and grease laden surfaces clean e Always turn hood ON when cooking at high heat e Use high settings on cooking range ONLY when necessary Heat the oil slowly on low to medium setting Do not leave cooking range unattended when cooking Always use cookware and utensils appropriate for the type and amount of food prepared Use this unit only in the manner intended by the manufacturer Before servicing switch power off at service panel and lock service panel if possible to prevent power from switching on accidentally e Clean ventilating fans frequently Grease should not be allowed to accumulate on fan safety screens and oil containers What to Do In The Event Of a Range Grease Fire SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray and then turn off the burner KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES the flames do not go out immediately EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911 NEVER PICK UP A BURNING PAN You may get burned DO NOT USE WATER including wet dishcloths or towels a violent steam blast will result Use an extinguisher ONLY if a You have a Class A B C extinguisher and know how to operate it b The fire is small and contained in the area where it started c The fire department has been called d You can fight the fire with your back to an exit What to Do If You Smell Gas Extinguish any open flame Do not try to turn on
17. red or supplied by it to free from defects in workmanship and materials Its obligations pursuant to this warranty are limited to period of two years from the date of purchase and to the repair or replacement at its option and subject to the terms and conditions stated below of any component part which its examination shall disclose to be so defective TWO YEAR WARRANTY SERVICE PERIOD Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable Keep proof of purchase or original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner is protected until expiration of the original purchaser s warranty CONDITIONS The following conditions apply only in relation to the warranty expressly given in this certificate 1 This warranty applies only a within U S A and Canada b to range hoods used for PRIVATE SINGLE FAMILY USE if used for COMMERCIAL or MULTIPLE FAMILY USE or other purposes warranty is void 2 Repair of any fault to be provided under this warranty shall not be provided a if the identification number attached to the range hood has been altered rendered illegible or removed b if notice of the defect has not been given within the p
18. s Rubber Stand 2 pcs INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation Calculate the length of the installation before installing the hood All calculation is measure in inches FOR UNDER THE CABINET TABLE 1 A Height of Floor to Ceiling B Height of Floor to Counter Top Standard 36 C lt Preferred Height of Counter to Hood Bottom Recommended 27 to 30 D Height of Hood E Height of the Cabinet TABLE 2 A Height of Floor to Ceiling B Height of Floor to Counter Top Standard 36 C lt Preferred Height of Counter to Hood Bottom Recommended 27 to 30 D Height of Hood E Height of Duct Cover F D F Height of the Hood Installation A B C UNDER THE CABINET INSTALLATION ASAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING CLEANING OR SERVICING Preparation before Installation NOTE TO AVOID DAMAGE TO YOUR HOOD PREVENT DEBRIS FROM ENTERING THE VENT OPENING Decide the location of the venting pipe from the hood to the outside Refer to Figure 1 Temporarily wire the hood to test for proper operation before installing Peel protective film off the hood if any For installing under the cabinets with recessed bottom attach 4 inch wide wood filler strips not included on each side Refer to
19. veling point of the hood Position two mounting screws not provided on the wall leaving 1 8 away from the wall as shown on Figure 11 Align hood mounting bracket to the two screws on the wall and hook hood into place Tighten screws to secure hood to the wall CAUTION MAKE SURE THE HOOD IS SECURE BEFORE RELEASING Hood Mounting Mounting Screws Bracket Figure 10 Figure 11 Duct Cover Installation 4 Mark the position of the duct cover mounting bracket Use calculation E from Table 2 for reference Attach and secure duct cover mounting bracket with two screws not provided Refer to Figure 12 NOTE Inner duct cover will cover the duct cover mounting bracket Connect electrical wires Refer to Wiring to Power Supply If necessary to hide the electrical wire connections push wires back into the hood Access the wire connections underneath the hood by removing the bottom casing from the six screws Before reattaching the bottom casing make sure wires do not slip between motors impellers or any moving parts to prevent any damage Use aluminum or steel pipe to connect the exhaust opening on the hood to the ductwork above Use duct tape to make all joints secure and air tight Slide the inner duct cover up 2 inch before sliding the entire duct cover onto the hood Refer to Figure 13 Figure 12 Figure 13 Adjust the height of the inner duct cover to the duct cover mounting bracket Secure inner duct cover with two
20. ving the bottom casing from the six screws Before reattaching the bottom casing make sure wires do not slip between motors impellers or any moving parts to prevent any damage ASAFETY WARNING RISK OF ELECTRICAL SHOCK THIS RANGE HOOD MUST PROPERLY GROUNDED MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES BEFORE CONNECTING WIRES SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY Connect three wires black white and green to house wires and cap with wire connectors Connect according to color black to black white to white and green to green Test the operation of the hood before moving on to next step Make sure power is supplied to the hood Install Accessories 8 Place the oil container round into keyhole under each safety screen Turn clock wise until firmly in place Refer to Figure 6 9 Slide oil container oval into plastic slot behind each safety screen Refer to Figure 7 Figure 6 Figure 7 Final Assembly 10 Turn power ON in control panel Check all lights and blower operation 11 Make sure to leave this manual for the homeowner STAND ALONE INSTALLATION installation only applied with the purchase of a duct cover ASAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING CLEANING
Download Pdf Manuals
Related Search