Mars MARS-10 Remote Starter User Manual
Contents
1. 20 Gauge Gray Wire is NOT Used Wire Harness the 20 Gauge Brown Wire is NOT Used Programming the Yellow Green Wire peration Locate and open the small access panel n the top of the control module case Place the umper as shown on the pins below the removable anel on the control module The factory setting is Accessory le center Ignition 2 position Ignition 2 Wiring 3 Wire Connector Satellite Relay Port The Red satellite relay port can be used if needed to configure optional relays to energize additional Ignition or Starter circuits and Omega OEM security bypass interfaces also plug into this port Prewired dual relay sockets are available and a plain 3 wire harness is provided to use this port 22 Gauge Green Wire 500mA Starter Output Connection If Needed This 22 gauge Green wire is a 500mA Negative output having basically the same operation as the 12 gauge Green Starter output wire If two or more Starter wires are present in the vehicle an optional relay is needed connected to satellite port Green wire as shown in the diagram 22 Gauge Red Wire Output For Optional Relay Coil Connection If Needed The Red wire supplies constant 12 Volts that can be used to power the relay s coil only DO NOT use this Red wire for the optional relay s power input pin 87 e Feature 3 is Single or Double Pulse Activation The Double Pulse AD option allows the MARS 10 in certain vehicles to activ2. Features 1 has a daily use benefit to the vehicle operator e Feature 1 is Engine Running Time When MARS remotely starts the engine the run time before automatic shut off is adjustable A 10 minute run time is the factory setting with options of 20 30 or 40 minutes When programming press the brake pedal 1 time for the default set 10 minute run time or press the brake 2 times for 20 minutes 3 times for 30 minutes or 4 times for 40 minutes e Feature 2 is Starter Cranking Time which sets the base starter cranking time for the Smart Start voltage sensing engine detection method page 34 When using Smart Start a longer starter cranking time may be used for engines which do not start on the first remote start attempt Programming choices are 5 second LOCK the default setting 75 second UNLOCK 1 25 second START and 1 5 second TRUNK 22 Gauge Blue Wire 500mA Ignition Output SE Connection If Needed ctay This 22 gauge Blue wire is a 500mA Negative output which has the same operation as the 12 gauge Blue Ignition output NOTE If an additional Acc To Additional 499 Starter Circuit N3 Fused constant 12 Volts To Additional Red Ignition Circuit essory output is e 3 pin needed use the Harness programmable built in relay Yellow Green wire Optional Relay Fused constant 12 Volts Wiring Connections 12 Wire Harness NOTE On the 12
3. Guarantee Or Insurance Policy Against Loss The Company neither assumes nor authorizes any person or organization to make any Warranties or assume any liability in connection with the sale installation or use of this product This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation The manufacturer is not responsible for any radio TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment One or more of these patents may apply to this product 5 612 669 5 654 688 5 663 704 5 729 191 5 818 329 5 612 578 5 739 747 382 558 385 878 5 750 942 5 739 748 5 719 551 406 107 701 285 5 973 592 5 982 277 5 986 571 6 011 460 6 037 859 6 049 268 6 130 605 6 130 606 6 140 938 6 140 939 6 150 926 6 144 315 6 184 780 6 188 326 6 243 004 6 249 216 6 275 147 6 297 731 6 320 514 6 320 498 6 346 876 6 346 877 6 366 198 6 392 534 6 429 768 6 433 677 6 480 095 6 480 117 6 480 098 Foreign Patent 199700312 EP0817734B1 98906445 6 2 320 248 701 285 08 05 MA_MARS10 11 OPERATING amp INSTALLATION MARS INSTRUCTIONS gt IMEGA RESEARCH AND DEVELOPMENT MARS 10 uMARS 1 1 Add on operation
4. module wires will be used Most installers will list these CEN wires then map out the installation by locating and noting the target wires in cl the vehicle This will also determine the best location for the MARS control module which is mounted upon completion of the installation The MARS remote starting unit duplicates the actions that occur within the ignition switch when you use your key to start the engine Because of this most of the main wiring harness connections will be made at the ignition switch harness The ignition switch wires usually are high amperage circuits which means that high reliability connections must be made soldering of all connections is recommended Caution Avoid the Airbag circuit Especially avoid any harness or wires encased in Yel low or Red tubing or sleeves Do not use a standard test light as it can deploy an airbag or damage on board computers and sensors Main Module The MARS Main Module should be mounted in a location close to the ignition switch where many of the wiring connections are made typically hidden behind the driver s side dash Valet Switch and Status Light Carefully select locations in which the Valet Switch may be easily reached and the Status Light may be easily seen by the driver Both locations will need clear space behind the panel Drill a 15 64 hole for the Status Light and a 17 64 hole for the Valet Switch Mount these items and carefully route their wires to
5. with Stand Alone or Add on existing transmitters operation with dedicated function transmitters REMOTE STARTER FOR AUTOMATIC TRANSMISSION VEHICLES ONLY COPYRIGHT OMEGA RESEARCH amp DEVELOPMENT 2005 D Contents Operation Guide Introduction A Safety Considerations cccceeceeseeeeeeeeeeeeeeeseeeseeeeeeeseaeeeeeeeaeeeneeeeas tho Activate Remote Startas oreraa oak edie ool tin Rare eerie Deactivating Remote Grat Valet MOGG MEE cc sesestcidesddccadecdicssas dt E E T Programming Transmitters MARS 11 only Limited Lifetime Warranty AN Programming Features seisseen onra asediate oa eaa aiaa iae oi pi erai 8 10 About the Programmable Features 10 11 Installation Instructions Installation Considerations Cautions and Warnings sssssssssssresseneerrnsennesenne 12 13 Malu MOGUle Ze a ee sheet At 13 Valet Switch and Status Light 0 ccceeceeeeeeeeeeeeeeeeeeeeeeseaeeseeeseaeeseeeeaeesieeseneeeneeeaas 13 Wining Dagia aae a a a a E aa EE 14 15 MARS 11Receiver Module 16 6 Wire Main Ma e a EE A AAE E E E E TE 16 18 3 Wire CONNECIOR onnaa ees et ein et eee Se 18 19 12 Wire Harness ccccccccccecececeeessseceeeeeeeceeaneeesseseceeseeeeeauaeaaseceeeeeecetsnaaaaaeseeeess 19 26 9 ez prevents accidental starter grind should the key be turned while the remote starter is in operation Additionally the Orange wire also provides the vehicle immobilizing feature for the Anti Carjacking ope
6. Car Starter into a manual transmission vehicle Doing so could cause serious property damage personal injury and will void all warranties Be aware of and avoid any airbag circuitry Due to the fact that an installer may not be in a normal upright seated position severe injury may occur in an accidental airbag deployment The use of a Digital Multimeter DMM or Volt Ohm Meter VOM instead of a standard testlight is required This can greatly reduce the risk of an acciden tal airbag deployment or on board computer damage Battery gases are explosive Avoid sparks and do not smoke while working near the vehicle s battery Always protect wires routed through the firewall from sharp metal edges and hot parts of the engine Always fuse positive wires at their source Installation Considerations This entire booklet should be read before starting the installation An understanding of which control module wires are to be used and their functions is essential Installations will vary from car to car as some control module wires are required while others are optional Before starting the installation it should be deter the 3 pin Red port to energize the second Starter wire KE Note H a security system is present which utilizes a starter interrupt circuit zl the Green wire must be connected to the Starter Motor side of the interrupt 12 Gauge Yellow Wire Ignition Output Connection Required Connect the Yellow wire to the vehicle s I
7. LIMITED LIFETIME WARRANTY Products manufactured and sold by OMEGA RESEARCH amp DEVELOPMENT INC the Company are warranted to be free from defects in materials and workmanship under normal use If a product sold by the Company proves to be defective the Company will repair or replace it free of charge within the first year and thereafter all parts to be repaired will be free with only a nominal charge for Omega Research and Development Inc s labor and return shipping to the original owner during the lifetime of the car in which it was originally installed All products for warranty repair must be sent postage prepaid to Omega Research amp Development Inc P O Box 508 Douglasville Georgia 30133 with bill of sale or other dated proof of purchase This warranty is nontransferable and does not apply to any product damaged by accident physical or electrical misuse or abuse improper installation alteration any use contrary to its intended function unauthorized service fire flood lightning or other acts of God This warranty limits the Company s liability to the repair or replacement of the product The Company shall not be responsible for removal and or reinstallation charges damage to or theft of the vehicle or its contents or any incidental or consequential damages caused by any failure or alleged failure of the product to function properly Under No Circumstances Should This Warranty Or The Product Covered By It Be Construed As A
8. STARTER OUTPUT EE N Light A RECEIVER PORT VALET SWITCH PORT Program Jumper inside case below removable door STATUS LIGHT PORT
9. ate remote starting by Y locking the vehicle doors two times with the original keyless entry transmitter Exact operations and vehicle suitability varies consult with the installer for specific details Feature 4 is Gasoline or Diesel Engine When programming press brake pedal once for the Gasoline setting Diesel engines have three options pressing the brake twice selects Monitor Glow Plug Wire by which the MARS delays engaging the starter until its glow plug input wire detects the glow plugs turning off and two preset delay periods before starter engagement 10 seconds press brake 3 times and 20 seconds press brake 4 times Feature 5 is Reset and returns all Programmable Features to their factory default settings To do this enter programming mode select Feature 5 and press the brake pedal once The MARS will acknowledge resetting the features turning off the parking lights flashing the Status Light once and then immediately exiting programming mode with the normal confirmation of 2 short and 1 long Status Light flashes and turning off the parking lights Note When a Programmable Features Reset is used any feature which needs to be in a setting different from the default setting will have to be reprogrammed D Installation Instructions After reading this manual start the installation by affixing the WARN ING DECAL to a visible area in the engine compartment Do not attempt to install this Remote
10. eature has been chosen if needed reenter the Valet Switch presses 4 Once the feature has been confirmed press the brake pedal 1 time for the first default setting choice or press the brake pedal 2 3 or 4 times to select the second third or fourth settings feature 3 only has two settings see chart on previous page The Status Light will flash on the same number of brake presses and the parking lights will flash off the same number Once these flashes occur the feature is set e More features to program Go to step 5 e Only needed to program the one feature Allow MARS to exit Programming Mode 5 Select another feature by again making a new entry of Valet Switch presses repeating step 3 and again setting the newly chosen feature with the transmitter as in step 4 K Exiting Programming Mode ka Simply allow the MARS to time out of Features Programming Mode by not perform ing any programming actions for 15 seconds or turn the ignition On to immediately exit the programming mode The MARS indicates its exit from Features Programming Mode with 2 short and 1 long Status Lights flashes and the parking lights turning off About the Programmable Features Of the five MARS Programmable Features four are strictly installation related and one is operational in nature Installation related features adapt the MARS to certain vehicle situations these are to be utilized at the time of the installation only Only
11. ever the MARS has an unlock output or its remote start operation is activated 20 Gauge Yellow Red Wire OEM Arm Output Connection If Needed This output may be used to arm a factory installed alarm or if the vehicle is equipped with a Retained Accessory Power circuit this output can be used to spike the door pin switch wire which will turn off the Retained Accessory Power circuit To arm a factory alarm after remote start engine run stops connect the Yellow Red wire to the vehicle s factory arm wire This wire will show Negative polarity when a key is held in the lock position in the door key cylinder This wire can usually be located in either kick panel in the wiring harness from the door as it is routed between the door key cylinder and the factory alarm To use this wire to turn off Retained Accessory Power locate a vehicle wire within the door or doorjamb which shows Negative when the door is open Should such a wire be found which is positive a relay is needed to reverse the Yellow Red wire s Negative output to Positive The Yellow Red wire produces a Negative pulse output whenever the system turns off the engine after it has been remotely started 20 Gauge Pink Black Wire Start Activation Input Connection If Needed The Pink Black wire allows for alternative devices such as an ez 1 Connect the Black Yellow wire to the vehicle s tach wire which is found in the I engine compartment although in many cases
12. gine Gasoline Diesel Monitor 10 20 Press brake pedal 1 time to reset D 5 Reset All Features To Default all features to the default setting 20 Gauge Black Yellow Wire Engine Detect Input G Connection Required The Black Yellow wire is the engine detect wire The 7 MARS unit utilizes two different methods of monitoring the vehicle during the remote start ing process Consider both methods before selecting one to use and then connect the Black Yellow wire accordingly Either connection method must be performed at the completion of the installation after all other wiring connections are made Smart Start sensing is more commonly used for its ease of installation The unit as received has Smart Start selected Smart Start reads the vehicle s battery voltage level via the Black Yellow wire to determine engine running status To use Smart Start 1 Connect the Black Yellow wire to constant Battery 12 volts This may done at the ignition switch harness or at the battery itself for better sensitivity 2 Switch the selector slide switch on the MARS control module to the left toward the module corner see the wiring diagram and the markings on the control module 3 Adjust Smart Start by starting the engine and turning the left adjustment screw on the control module slowly clockwise until the indicator LED starts flashing Turn the adjust ment until the LED is flashing in a consistent and regular manner 4 Test
13. gnition wire also known as Primary Ignition This wire will show 12 Volts when the ignition key is in the Run and Start positions and no voltage in the Off and Accessory positions This wire is found in the ignition switch wiring harness Note If two Primary Ignition wires are present use the Yellow Green wire for the second or configure an optional relay to the 3 pin Red port 12 Gauge White Wire Accessory Output Connection Required Connect the White wire to the vehicle s Accessory wire This circuit supplies power to the Heat Ventilation and Air Conditioning HVAC system This wire will show 12 Volts when the ignition key is in the Run and Accessory positions and No voltage in the Start and Off positions The connection point for this wire is also found in the ignition switch wiring harness 12 Gauge Yellow Green Wire Programmable Output Connection If Needed The Yellow Green wire is an additional output which can be programmed to operate as an Ignition output Accessory output or Starter output As re ceived it is programmed as an Ignition 2 output This wire may be used in cases where the vehicle has more than one of any of these three circuits 46 MARS 11 Receiver Module The MARS has a plug in window mount Receiver Module Optimum performance is obtained by mounting this module high and unobstructed on the vehicle s glass such as the windshield behind the rearview mirror Make sure the glass surface
14. is clean and free of dust grease or debris Peel the backing off of the adhesive tape and affix the Receiver Module Carefully route the receiver s 3 wire ribbon cable to the control module plug the cable into the Black 3 pin port on the rear of the module Wiring Connections 6 Wire Main Harness Two 12 Gauge Red Wires Constant 12 Volts Input Connection Required Connect both Red wires to constant 12 Volts The source used must supply adequate amperage The most common sources are the battery terminal or the ignition switch wiring harness Good reliable connections and use of the included fuses are a must Note that some ignition switches have the electrical switch as part of the mechanical switch others have the electrical switch lower on the steering column and connected to the mechanical switch by a linkage The ignition switch wiring harness is the best source for these wires and the Starter Ignition 1 and Accessory wiring connections 12 Gauge Green Wire Starter Output Connection Required Connect the Green wire to the vehicle s Starter wire This wire will show 12 Volts only when the ignition key is in the Start position This wire is also found in the ignition switch wiring harness Some vehicles have a second Starter wire known as a Cold Start wire When this is encountered two options are available program the Yellow Green wire as a second starter output or use an optional relay configured to mined which control
15. it may also be located inside the ve hicle To use a multimeter to verify the correct tach wire set it for AC Volts scale The correct wire will read 1 to 6 volts AC at idle and will increase with engine speed 2 Switch the selector slide switch on the MARS control module to the right toward the 12 pin secondary harness see diagram or the markings on the control module 3 Adjust the tach signal by starting the engine and turning the right adjustment screw on the control module slowly clockwise until the indicator LED lights solid 4 Test the operation by remote starting and checking that the indicator LED slights solid The starter engagement is long enough for the engine to start but without grinding If needed adjust the crank time by turning the adjustment screw clockwise for more signal sensitivity and counterclockwise for less 20 Gauge Green Red Wire Glow Plug Input Connection If Needed The Green Red wire allows the MARS to be used with diesel engines operates only if programmed feature 13 and is also polarity programmable Connect the Green Red wire to the wire in the vehicle which powers the glow plugs or the wire which illuminates the Wait To Start light on the instrument panel When connected the unit will not engage the starter if the Green Red wire has 12 Volts in other words using this wire simply delays the units engagement of the starter If the Wait To Start light in the vehicle has a Negative s
16. n of this circuit 20 Gauge Blue Wire Hood Input Connection Required The Hood Safety Switch must be installed and the Blue wire must be connected This prevents operation of the unit if the hood is open The Blue wire s second function is being a sensing wire to trigger the alarm if the MARS is armed Carefully install the included pin switch so that it is open pin down when the hood is shut and closed pin up when the hood is open Connect the Blue wire to the pin switch and carefully route this wire through the firewall using an added or existing grommet avoiding any hot or moving parts Instead of using a pin switch to monitor the hood s open or shut status an Omega AU 46 Mercury Tilt Switch may used Connect one of the AU 46 s wires to Negative Chassis Ground and connect the remaining wire to the Blue wire How to program features 1 Turn the ignition key On then Off D B 2 Within 7 seconds press the Valet Switch 5 times The Status Light will flash twice then turn off The parking lights flash twice and then stays on while in programming mode 3 Select the feature to be changed by pressing the Valet Switch the same number of times as the feature number example feature 3 3 presses The Status Light will flash the same number as the Valet Switch presses just entered The parking lights will flash off the same number then come back on Count the number of flashes to confirm that the desired f
17. nfirm exiting valet mode Programming Transmitters MARS 11 ONLY The MARS 11 can be operated by additional transmitters up to four total Additional or replacement transmitters must be programmed to operate the MARS 11 e Have present all of the transmitters which are to operate the MARS 11 Whenever a transmitter is programmed to the system any existing ones are automatically erased for security Therefore all of the transmitters which are to operate the system must be programmed at the same time 1 Turn the ignition key On and leave it on 2 Within 7 seconds press the Valet Switch 5 times The parking lights flash once and the system Status Light turns on steady 3 Within 15 seconds press the first transmitter s button The MARS will acknowledge the transmission by momentarily turning off the Status Light and flashing the parking lights once e Another transmitter to program Go to step 4 e Only needed to program the one transmitter Allow MARS to exit programming mode factory alarm system Connect the Yellow Green wire to the wire in the vehicle G which is connected to one of the doorlock key cylinders The typical OEM alarm S has an electrical switch in the key cylinders which switches Ground when the key unlocks the door This wire can usually be located in the vehicle in either kick panel area in the wiring harness which is routed into the cab from the door The Yellow Green wire has a Ground pulse when
18. on and also independently operate the MARS 11 system with B position If a MARS 2 way controller is programmed to operate the MARS 11 it will operate it activating remote start but the MARS 11 can not transmit a signal back to the controller therefore the 2 way controller will not have the confirmation operation that remote starting has occurred O Installation It is highly recommended that this system be professionally installed as the sophistication of the modern automobile and the complexity of this type of product installation is often beyond the abilities of most do it yourselfers The remainder of this booklet is comprised of the Installation instructions which includes the programming of features Programming Features The MARS 10 11 has 5 programmable features which are installation related in that they set parameters or make allowances for certain conditions which may be set by the vehicle the system is installed in or by the remote start activation means There is only one programmable feature feature 1 Engine Run Time which is of any benefit or inter est to the vehicle owner or system user Otherwise the programmable features should not be changed after installation FEATURE DEFAULT A OPTION Se wel 1 Engine Running Time 10 Minutes 20 30 40 Min 2 Starter Cranking Time 5 Second 75 1 25 1 5 Sec 3 Single or Double Pulse Activation Single Double 4 Gasoline or Diesel En
19. pedal will turn the engine off e To stop the engine by remote control simply press the same button s used to start it e Otherwise after the preset programmable time the MARS will turn the engine off e Opening the hood will turn the engine off If the hood is open when an activation attempt is made the MARS will only flash the parking lights 4 times but will not start the engine e Pressing the Valet Switch will also stop the engine The preset engine running time is 10 minutes and 20 30 and 40 minutes are optional Valet Mode The MARS may be placed into a valet mode which prevents the remote start feature from being activated Valet Mode should always be used when you do not wish for the remote starter to be operated such as when you have your vehicle serviced or leave it with someone else The Valet Switch a small push button is used check with the installer for the location of this switch e At any time simply press the Valet Switch for 5 seconds the Status Light will light steady to indicate Valet Mode and stay illuminated continuously while the system is in Valet Mode gt Once the MARS is in Valet Mode an attempt to remote start will instead be ac zl knowledged by the parking lights turning on then flashing rapidly then 3 slow flashes but no engine starting attempt will occur e To turn off Valet Mode simply press the Valet Switch until the Status Light turns off and the parking lights flash once to co
20. ration Connection instructions are included with op tional starter interrupt socket and relay Introduction es Congratulations for choosing the Modular Advanced Remote Starter and Security System and enjoy the luxury of starting your vehicle s engine from the comfort of your home or office MARS is a complete series of convenience and security systems this version is remote starting only although the flexibility of its design allows its use in two distinct forms e The MARS 10 is operated by use of an existing keyless entry or alarm system e The MARS 11 is operated by its own dedicated transmitter device Both MARS 10 and MARS 11 systems utilize a Status Light for visual indicators and a Valet Switch to turn the system off and to program it The MARS 11 has a small window mountable receiver unit in addition to its single button transmitter Safety Considerations v This unit is for vehicles with an automatic transmission only Installation in a vehicle equipped with a manual transmission can result in property damage or personal injury v This unit is for fuel injected gasoline or diesel engines y Children should not be left unattended in or be allowed to play with the activating trans mitter device of any remote starter equipped vehicle v Do not use the remote starter feature in an enclosed garage or other structure The MARS is a very flexible system It has capabilities and features which may or may not be utilized in your ins
21. tallation It also has programmable features which can affect its operation While these are explained as thoroughly as possible in this guide your Omega dealer or installer is the best source for information about your system D To Activate Remote Start MARS 10 MARS 11 Press the necessary button or Press the blue START button combination on the button on the MARS host system s transmitter system s transmitter The parking lights will flash 3 times The MARS will turn on the ignition circuit turn the parking lights back on steady and the system s interior Status Light will also start flashing Within a few seconds the parking lights will turn off and the starter will engage The engine will start run and the starter will be disengaged The parking lights will turn back on and remain on while the MARS is controlling the engine The status light will pause and then continue to flash slowly Should the engine stall the MARS will make two attempts to restart it The MARS 10 is an add on unit operated by use of an existing keyless entry or alarm system transmitter The MARS 11 is operated by its own dedicated single button transmitter Therefore the MARS 10 remote start activation proce dure will vary in some cases the host transmitter may have an open button which can be used for remote starting in other cases pressing the host transmitter Lock button 2 times within 5 seconds will activate remote start Consult wi
22. th the installer diagrams The correct wire will show 12 Volts only when the headlight switch is in OB the Parking Light and Head Light positions This wire can usually be found at Y the headlight switch and various other locations within the vehicle such as the rear body harness or firewall connector Caution When such a wire is located be sure to also test that it is non rheostated While metering the wire operate the dash light dimmer control The correct wire will show no change in voltage when the dimmer is operated Some vehicles have a parking light relay which is triggered by a Negative signal from the headlight switch In these vehicles the White wire must be connected after the relay usually at the Fuse Junction Block Do NOT connect the White wire directly to the vehicle s headlights An external relay is re quired Vehicles having a split parking light system must be diode isolated with two IN4006 diodes as shown Right Side Circuit Hal E Control Two IN4006 Diodes 2 D H c White Wire Switch S Diode Isolation Of Split Parking Light Systems 20 Gauge Orange Wire Anti Grind Output Connection If Desired The function of the Orange wire is to provide a 500mA Nega tive auxiliary output which may be used to operate a starter motor Anti Grind relay which OR existing keyless entry or alarm system to activate the remote start operation If the J Pink Black wire recei
23. the Main Module Yellow Green Programmable Output Battery Red amp Red 12 Volts eS OPTIONAL Relay For Anti Grind WIRING DIAGRAM Orange Output When Activated Green Starter Parking Lights Ignition Fo Light Switch White Parking Light Output Hood Pin Switch Blue Hood Switch Pink Black Start Activation Green Red Glow Plug Input Black Yellow Tach Wire Smart Start To Battery To Coil Red Black Brake Gray NOT USED Brown NOT USED TOL Amp Yellow Green OEM Disarm Yellow Red OEM Arm Smart Start v Tach Wire Black Ground Tach Smart Wire Start Adjust Adjust Adjustment J Valet cl Switch Led Receiver 415 Unit MARS 11 ONLY Status SMART START TAcHWwIRE SWITCH YELLOW RED OEM ARM OUTPUT BLACK YELLOW ENGINE DETECT INPUT RED BLACK BRAKE INPUT YELLOW GREEN OEM DISARM OUTPUT GRAY NOT USED BLUE HOOD INPUT ORANGE ANTI GRIND OUTPUT PINK BLACK START ACTIVATION INPUT BROWN NOT USED GREEN RED GLOW PLUG INPUT WHITE PARKING LIGHT OUTPUT BLACK CHASSIS GROUND PARKING LIGHT PROGRAM JUMPER GLOW PLUG PROGRAM JUMPER SATELLITE RELAY PORT RED 12V INPUT YELLOW GREEN PROGRAMMABLE OUTPUT YELLOW IGNITION OUTPUT RED 12V INPUT WHITE ACCESSORY OUTPUT GREEN
24. the operation by remote starting and checking that the indicator LED shows the same consistent flashing good voltage signal learned and that the starter engage ment is long enough for the engine to start but without grinding Turn clockwise for more crank time and counterclockwise for less crank time Tach Wire sensing is generally more reliable and preferable in cases were the engine normally starts inconsistently or is hard to start With this method the Black Yellow wire reads the engine speed tach information directly from a wire in the vehicle To use the Tach Wire method 20 18 Gauge Black Wire System Ground Connection Required Connect the Black wire to a very good clean chassis ground A recommended connection is to an existing machine thread bolt either in the driver s kick panel steering column area or a major structural member behind the dash Small dash braces are not adequate and the area must be clean bright metal 20 Gauge Red Black Wire Brake Input Connection Required The Red Black wire must be connected It is part a critical safety feature which disables the unit whenever the brake pedal is pressed Connect the Red Black wire to the brake switch wire which shows 12 Volts when the brake pedal is pressed The brake switch is typically located above the brake pedal and usually mounted to the brake pedal support bracket Make this connection securely for long term reliability and thoroughly test the operatio
25. ves a Negative pulse the MARS unit will start the vehicle s engine provided that all safety circuits are in the proper status After the engine has been started by remote control another Negative pulse on the Pink wire will turn the unit off stopping the engine The Pink Black wire can be connected to an available auxiliary output of an existing Re mote Security System and the unit s remote control may also be used to activate the remote start operation 18 Gauge White Wire Parking Light Output Connection Recommended The White wire is a programmable output to the vehicle s exterior parking lights to visually confirm system operations 12 Volt or Nega tive output may be selected by the Black jumper next to the doorlock port Connect the White wire to the vehicle s 12 Volt parking light circuit as shown in the accompanying Typical Parking Lights Connection Dash Board Control Note output D Lights Module polarity is selectable D Jumper Dimmer White Wire Parking Lights Parking Lights When you leave your vehicle simply set the climate controls for what you would O like to have operating upon remote starting the heater defroster or air conditioning Upon entering the vehicle place the ignition key in the switch and turn it to the On posi tion and then deactivate the MARS Do not turn the key to the Start position Deactivation e Stepping on the brake
26. witching circuit change the position of the White Glow Plug Select Jumper on the module to reverse the Green Red wire s polarity input 20 Gauge Yellow Green Wire OEM Disarm Output Connection If Needed f needed the Yellow Green wire allows the MARS to disarm a 4 Within 15 seconds press the next transmitter s button The Status Light turns off and the parking lights flash once Repeat this action for each remaining transmitter e o Exiting Transmitter Programming Mode Simply allow the MARS to time out of the programming mode by not transmitting for 15 seconds or turn the ignition Off to exit immediately The MARS indicates its exit from programming mode by turning off the Status Light If it is allowed to time out the ATV display shows the number of operating transmitters for 10 seconds afterward The MARS 11 can also be operated by the multi button 1 way transmitter or the 2 way controller which are used in other MARS systems The transmitter and controller used in other MARS systems has an A B switch for multi car operation To program another multi button transmitter or controller to operate the MARS 11 enter programming mode reprogram the original 1 button transmitter and then program the multi button transmitter or controller by pressing its Start button with the A B switch in the B position The transmitter controller will operate its original system with A positi
Download Pdf Manuals
Related Search