Electrolux 2020 D Ventilation Hood User Manual
Contents
1. l Remove the metal cover by unscrewing the four self tapping screws 2 Connect the Push Fit connectors coming from the fan assembly to the canopy 3 Position the terminals as illustrated under the cover and replace the cover with the four self tapping screws 4 Once the electrical connection has been completed check that the worktop lighting fan motor and the speed selection is working properly 5 Replace the charcoal filter if the hood is to be used in the recirculation mode and the metal grease filter cassette S07_34 19 Dir 89 336 CEE 73 23 CEE 4329477 01 0010132. If the hood is to be fitted in conjunction with wooden shelves or cornice see the separate installation instructions before fixing the hood in position lt gt Fixing the hood to the wall Whichever type of installation is to be carried out if the a j hood is to be fitted in conjunction with wooden shelves y I 1 N these will require drilling before the hood can be StL Racal installed m Drilling the shelves Bottom Shelf OS 1 Use the cardboard template provided to mark the hole positions on the shelf 2 Using hole B as a reference point drill the shelf along the centre axis for the chimney to pass through E es lal INSTALLING INSTRUCTIONS 3 Slide the chimney through the hole in the shelf before fixing it to the canopy Top Shelf The top shelf only requires drilling if the hood is to be installed with the air outlet turned upwards 1 Use the cardboard template provided to mark the hole position on the shelf 2 Using the hole B as a reference point drill the shelf along the centre axis for the chimney to pass through gt Installation in the recirculation mode The cooker hood is specified for installation in the recirculation mode with the charcoal filter fitted ie Draw a vertical line on the wall from the centre of the cooking appliance using a spirit level and marking pen This is to ensure the correct vertical alignment of the appliance 2 Using the card
3. environment plus those which are the subject of rental agreements Products of AEG manufacture which were not marketed by AEG This guarantee is in addition to your statutory and legal rights EUROPEAN GUARANTEE If you move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications e The guarantee starts from the date you first purchased your product e The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products e The product is installed and used in accordance with our instructions and is only used domestically i e a normal household The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care centre listed below to give them details of your new home They will ensure that the local Service organisation is aware of your move and able to look after you and your appliance France Senlis 33 0 3 44 62 29 99 Germany Nurnberg 49 0 911 323 2600 Italy Pordenone 39 0 01678 47053 Sweden Stockholm 46 0 8 738 79 50 UK Slough 44 0 1753 219899 INSTALLATION INSTRUCTIONS A N It is dangerous to alter the specifications or attempt to modify this product in any way Technical Information DIMENSIONS ELECTRICAL SUPPLY POWER CONSUMPTION FAN MOTOR LAMP SUITABLE FOR INSTALLATION ABOV
4. the canopy fixing holes 1 which is calculated by measuring the lenght of the chimney required for the installation plus 15mm to equal Z 16 10 11 INSTALLING INSTRUCTIONS Using a 8mm masonry bit drill the holes for the canopy and fan assembly and insert the rawl plugs ready for the fixing screws The hood is supplied with the air outlet facing the rear To rotate the extractor to face left or right proceed as follows Loosen the screws V1 turn the extractor 60 to the left or right as required then tighten the Screws To fix the bracket S select the left or right hand screw holes and using the screw V2 secure the bracket Unscrew the four self tapping screws and remove the plastic surround Fit the ducting spigot R using the four self tapping screws and replace the plastic cover Fix the round eyelet screws provided tightly into holes 1 and hook on the canopy C ensuring the hooks are located into the eyelets before releasing the canopy Unscrew the self tapping screws from the back of the fan assembly and remove the plastic surround Fit the ducting flange F onto the fan assembly utilising the same fixing holes and self tapping screws Insert the 4 2x44 4mm screws provided for fixing the fan assembly and chimney into the wall and tighten about two thirds Lower the fan assembly and chimney onto the fixing bracket S then fully tighten the screws 17 INSTALLING INS
5. 2020 D Cooker Hood Operating and Installation Instructions For the User Important Safety Information Your Appliance Operating Instructions Cooker Hood Controls To Operate Recirculation Extraction Maintenance and Cleaning External Cleaning Metal Grease Filter To Remove the Grease Filter Cassette Charcoal Filter To Remove Replace the Charcoal Filter Worktop Lighting Replacing the Light Bulb Something Not Working Service and Spare Parts Guarantee Conditions For the Installer Installation Instructions Technical Information Electrical Connections Electrical Requirements Electrical Connection Installing the Cooker Hood Installation Requirements Unpacking Clearance Height Selecting the Type of Installation Fixing the Chimney to the Canopy Fitting the Hood to the Wall Drilling the Shelves Bottom Shelf Top Shelf Installation in Recirculation Mode Installation with Air Outlet Turned to the Wall Installation with Air Outlet Turned Left or Right Final Fixing and Adjustment of Hood Ducting Recirculation Electrical Connection and Working Test Guide to use the instruction book The following Symbols will be found in the text to guide you through the instruction book A Safety instructions is Step by step instructions IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety Ensure that you understand them all before installing or using this appliance Yo
6. E HEIGHT CANOPY HEIGHT CHIMNEY WIDTH CANOPY WIDTH CHIMNEY GROSS NET 2x20W HALOGEN 35 mm GUA ELECTRIC HOB GAS HOB SLOT IN GAS COOKER SLOT IN ELECTRIC COOKER 73mm 450 850 mm 898 mm 200 0270 mm 24 00 kg 19 40 kg 220 240 V 50 Hz 215 W 175 W 40 W 7 KW 10 KW 13 5 KW 12 4 KW Note CE Marking certifies that this appliance complies with the requirements laid down in EEC directive 89 336 Electromagnetic compatibility and subsequent modifications and Low Voltage directive 72 23 E ELECTRICAL CONNECTIONS A This appliance must be earthed Electrical Requirements Any permanent electrical installation must comply with the latest E E Regulations and local Electricity Board regulations For your own safety this should be undertaken by a qualified electrician e g your local Electricity Board or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting NICEIC Electrical Connection This appliance is fitted with a 3 core mains cable and must be permanently connected to the electricity supply via a double pole switch having 3mm minimum contact gap on each pole A Switched Fuse Connection Unit to BS1363 Part 4 fitted with a 3 Amp fuse is a recommended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions Before connecting to the mains supply ensur
7. GUARANTEE CONDITIONS Standard Guarantee Conditions We AEG undertake that if within 12 months of the date of the purchase this AEG built in appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials the company will at our option repair or replace the same FREE OF ANY CHARGE for labour materials and carriage on condition that e The appliance has been correctly installed and used only on the electrical supply stated on the rating plate e The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s operating and maintenance instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us e All service work under this guarantee must be undertaken by an AEG Service Force Centre e Any appliances or defective parts replaced shall become the property of this company Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged EXCLUSIONS This Guarantee does not cover e Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic e Costs incurred for calls to put right appliances improperly installed or calls to appliances outside the United Kingdom e Appliances found to be in use within a commercial
8. TRUCTIONS gt Final fixing and adjustment of the hood Two adjustable connectors are provided at the rear of the hood a Turn the screws V1 until the screws V2 align with the screw holes F2 b Adjust the vertical and horizontal alignment using screws V2 c Turn the screw V1 to secure the hood to the wall d Insert the plastic grommets provided into the screw holes F2 e Tighten the screws fixing the canopy C to the chimney A gt Ducting and recirculation fitting Ducting 1 When ducting to the outside the charcoal filter is not required and must be removed and destroyed 2 When ducting from the rear outlet using 125mm round ducting it will be necessary to fit the 120 125mm ducting collar onto the spigot F before connecting the ducting to ensure an air tight fit This appliance must not be connected to ducting with a smaller diameter than 120mm 3 When ducted from the left or right hand side it will be necessary to fit the 60x204mm adapter W for use with flat channel ducting to the spigot R Recirculation 1 The hood is supplied in the recirculation mode with the charcoal filter and the recirculation grille G fitted over the outlet in the top of the fan assembly ready for use 2 The charcoal filter will have to be removed during installation to allow for electrical connection 18 INSTALLING INSTRUCTIONS A N Electrical connection and working test
9. board template provided mark the hole position 1 on the wall 100mm either side of the vertical line ensuring they are level and that the distance between the lowest point of the hood and the cooking appliance beneath meet the clearance requirements quoted in the paragraph titled Clearance Heights 3 Using the cardboard template mark the hole positions to be used for fixing the chimney 30mm either side of the vertical line The holes must be drilled at a distance of X from the horizontal line running through the centre of the canopy fixing holes 1 which is calculated by measuring the lenght of the chimney required for the installation plus 15mm equal Z 4 Using a 8mm masonry bit drill the holes for the canopy and the fan assembly and insert the rawl plugs provided ready for the fixing screws 650 yo S07_05 14 INSTALLING INSTRUCTIONS 5 Fix the round eyelet screws provided tightly into the holes 1 6 Fix bracket S to the fan assembly T The hood is supplied in the recirculation mode with the recirculation grille G fitted over the outlet in the top of the fan assembly ready for use 8 Insert the 4 2x44 4mm screws to be used for fixing the fan assembly into the rawl plugs and tighten about two thirds Lower the fan assembly and chimney onto the fixing bracket S Ensuring the screws locate into the fixing bracket than tighten the screws fully gt Installation w
10. e that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood This appliance conforms to BS 800 1988 and interference 10 EEC Directive No 78 308 regarding suppression of radio and television INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown All installations must comply with the local authorities requirements for the discharge of exhaust air Incorrect installation may affect the safety of this cooker hood Installation Requirements Before installation check the wall to which the cooker hood is to be fitted for electric cables water pipes or gas The cooker hood is designed to be fixed to any rigid vertical surface over a cooking area and can be used in the extraction ducted to the outside or recirculation internal recycling mode The Installation work must be undertaken by a qualified and competent person The manufacturer disclaims any responsibility to damages due to incorrect installation of the cooker hood or if the cooker hood is not installed in compliance with relevant regulations controlling this type of installation Unpacking Before unpacking the cooker hood position the carton with the arrows pointing upwards as illustrated on the carton The canopy is supplied with the following components for installation 1 No Canopy including controls and worktop il
11. e machine washed in a dishwasher gt To Remove the Grease Filter Remove the metal grease filter cassette by pushing inwardly on the two steel handles replace making sure the handle has sprung back into position and is completely visible Charcoal Filter The charcoal filter cannot be cleaned it should be replaced approximately every three months or more often if the hood is used for more than three hours per day MAINTENANCE AND CLEANING ISS To Remove the Charcoal Filter Push inwardly on the two retaining clips to disengage the security fixing and remove This appliance can be a fire hazard if the A grease and charcoal filters are not cleaned and replaced as recommended Worktop Lighting The lamps should be replaced with a 220 240V 20W halogen spot lamp gt To Remove the Lamps Unscrew the two screws to release the metal surround Remove a lamp from the holder by pulling the lamp downwards When fitting the new lamp ensure the two pins are correctly inserted into the slots in the lamp holder Charcoal filters grease filters and lamps can be obtained from your local Service Force Centre SOMETHING NOT WORKING If having followed these instructions carefully your cooker hood fails to work properly please carry out the following checks Symptom The cooker hood will not start The cooker hood is not working effectively The cooker hood has switched off during operation lf after all the
12. hood is designed to extract unpleasant odours from the kitchen it will not extract steam To obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking and leave it running for approximately 15 minutes after finishing Cooker Hood Controls V1 Push to engage the low speed for use with one burner or simmering V2 Push to engage the medium speed for normal cooking up to four pans V3 Push to engage the high speed for use when frying or cooking foods with strong odours L Push to switch on the worktop illumination lamps OPERATING INSTRUCTIONS This cooker hood can be used to recirculate or extract contaminated air Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted The contaminated air is cleaned by passing through the filters and than back into the kitchen The activated charcoal filter absorbs odours arising from cooking In use it will slowly become saturated in grease and less effective The filter normally requires changing after at least every three months or more frequently if the hood is used for more than three hours per day S07_29 Extraction The contamined air enters the cooker hood passing through the grease filter and out through the ducting into the atmosphere When used in the extraction mode the charcoal filter is not required and must be removed Never do flamb cooking
13. ith the air outlet turned towards the wall ie Draw a vertical line on the wall from the centre of the cooking appliance using a spirit level and marking pen This is to ensure the correct vertical alignment of the appliance 2 Using the cardboard template provided mark the hole positions 1 on the wall 100mm either side of the vertical line ensuring they are level and that the distance between the lowest point of the hood and the cooking appliance beneath meet Aj yy the clearance requirements quoted in the x ra a ee paragraph titled Clearance Heights an aie 00 100 B 3 Using the cardboard template mark the hole i positions to be used for fixing the chimney 30mm either side of the vertical line The holes must be drilled at a distance of X from the PE horizontal line running through the centre of the TA canopy fixing holes 1 which is calculated by measuring the lenght of the chimney required for the installation plus 15mm to equal Z as illustrated opposite 4 Using a 8mm masonry bit drill the fixing holes for the canopy and the fan assembly and insert the rawl plugs provided ready for the fixing screws 15 INSTALLING INSTRUCTIONS 5 Mark the position on the wall and drill the hole for the ducting To calculate the centre of the hole on the wall for the ducting draw a horizontal line D through the vertical line 80mm above line X The round ducting to be u
14. its flue must be of the room sealed or balanced flue type If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room When the hood is used in conjunction with appliances supplied with energy other than electricity the negative pressure in the room must not exceed 0 04mbar to prevent fumes being drawn back into the room by the hood The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose Do not install above a cooker with a high level grill Child Safety The appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the appliance During Use This appliance is for domestic use only Never leave frying pans unattended during use as over heated fats and oils might catch fire Never do flamb cooking under this cooker hood Do not leave naked flames under this hood Maintenance and Service This appliance can be a fire hazard if the grease and charcoal filters are not cleaned or replaced as recommended Under no circumstances should you attempt to repair the appliance yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Refer to your local Service Force Centre Always insist on genuine spare parts YOUR APPLIANCE 450 850 OPERATING INSTRUCTIONS This cooker
15. lumination C 1 No Telescopic chimney stack complete with fan motor A 1 No Flange 120mm F 1 No Collar 120 125mm 1 No Venting grille G 1 No Spigot R 1 No Ducting conversion bend W 1 No Support Rod B 11 INSTALLING THE COOKER HOOD Clearance Heights The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated provided the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications If the output of the appliance below the cooker hood exceeds the maximum outputs quoted please refer to the cooker manufacturer s installation instructions A minimum clearance height of 650mm 25 1 2 ins is required when installed above a built in electric hob or 700mm 27 1 2 ins when installed above a built in gas hob A minimum clearance height of 685mm 27 ins is required when installed above a slot in electric oven or 787mm 30 1 2 ins when installed above a slot in gas oven When installed between adjoining wall cabinets the wall cabinets must not overhang the hob and the distance beetween the underside of the cabinet and the worktop must be 450mm If the height of the wall cabinet is less than 450mm a gap of 50mm must be maintained either side of the hob This cooker hood must not be installed above a cooking appliance with a high level grill Selecting the type of installation The extraction unit at the top
16. of the chimney can be installed in one of three ways 1 Air outlet turned upwards recirculation only fig 2a 2 Air outlet turned towards the wall extraction only fig 3 3 Air outlet turned left or right extraction only fig 4a and 4b 12 A Built in Electric Hob 650mm minimum clearance B Built in Gas hob 700mm minimum clearance C Slot in Electric Cooker 685mm minimum clearance D Slot in Gas Cooker 787mm minimum clearance INSTALLING INSTRUCTIONS gt Fixing the Chimney to the Canopy 1 Remove the metal grease filter cassette by pushing inwardly on the two steel handles 2 To remove the charcoal filter push inwardly on the two retaining clips to disengage the security fixing and remove 3 Align the fixing points on the chimney with the corresponding fixing points on the canopy Ensure the guide in the two chimney sections is positioned at the back to face the wall 4 Fixing the chimney stack Insert gasket G1 found in the accessory bag on the base of chimney stack A so that it adheres perfectly to the shape of chimney stack A Then fix chimney stack A to the hood unit C using four of the screws provided E 5 Connect the supply cable from the canopy marked with adhesive tape to the cable from the fan motor by pushing together the two male and female connectors The metal grease filter and charcoal filter should not be refitted until after the hood has been fixed to the wall
17. se checks the problem persists contact your local Service Force Centre quoting the model and serial number Please note that it will be necessary to provide proof of purchase for any in guarantee service calls Check the hood is connected to the electricity supply Check that the fan speed control is set to 1 2 or 3 The fan speed is set high enough for the task The grease filter is clean The kitchen is adequately vented to allow the entry of fresh air If set up for recirculation check that the charcoal filter is still effective If set up for extraction check that the ducting and outlets are not blocked The safety cut out device has been tripped Tum off the hob and then wait for the device to reset In guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown SERVICE AND SPARE PARTS If you require an engineer or wish to purchase spare parts contact your local Service Force Centre by telephoning 08705 929929 Your telephone call will be routed to the Service Force Centre covering your postcode area For general assistance with your appliance or for information on other AEG products please contact our Customer Care Department Customer Care Department AEG 50 77 High Street Slough Berkshire SL1 1DZ Telephone 08705 350350 calls to this number may be recorded for training purposes
18. sed must be 125mm 6 Fix the round eyelet screws provided tightly into holes 1 and hook on the canopy C ensuring the hooks are located into the eyelets before releasing the canopy T Unscrew the self tapping screws from the back of the fan assembly and remove the plastic surround 8 Fit the ducting flange F onto the fan assembly utilising the same fixing holes and self tapping screws 9 Insert the 4 2x44 4mm screws provided for fixing the fan assembly and chimney into the wall and tighten about two thirds Lower the fan assembly and chimney onto the fixing bracket S than fully tighten the screws Le Installation with the air outlet turned left or right 1 Draw a vertical line on the wall from the centre of the cooking appliance using a spirit level and marking pen This is to ensure the correct vertical alignment of the appliance 2 Using the cardboard template provided mark the hole positions 1 on the wall 100mm either side of the vertical line ensuring they are level and that the distance between the lowest point of the hood and the cooking appliance beneath meet the clearance requirements quoted in the paragraph titled Clearance Heights 3 Using the cardboard template mark the hole positions to be used for fixing the fan assembly 107 5mm on the left or right of the vertical line The holes must be drilled at a distance of X from the horizontal line running through the centre of
19. under this A cooker hood Take extra care when frying and never leave frying pans unattended during use as over heated fats and oils can catch fire Do not leave naked flames under the cooker hood Ensure the hood is switched on before using the hob Ensure heating areas on your hob are covered with pots and pans when using the hob and cooker hood simultaneously Ensure not to damage the charcoal filter when cleaning or replacing as the activated charcoal inside is saturated with grease which will stain if it comes into contact with clothing or furnishings MAINTENANCE AND CLEANING f Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply The cooker hood must be kept clean a build up of grease or fat can be a fire hazard External Cleaning The metal casing grille and chimney should be cleaned at least once a month to keep it looking like new Wipe over the hood with a soft cloth wrung out in mild soapy water and then dry thoroughly Never use scouring pads or abrasive cleaners as they may scratch or damage the surfaces A Always wear protective gloves when cleaning the hood Never use scouring pads or abrasive cleaners Never use excessive amounts of water when cleaning particularly around the control panel Metal Grease Filter The metal grease filter should be cleaned at least every month The filter may be washed by hand using mild soapy water or can b
20. ur safety is of paramount importance If you are unsure about any of the meanings of these warnings contact the Customer Care Department Installation Any installation work must be undertaken by a qualified electrician or competent person This hood must be installed in accordance with the installation instructions and all measurements adhered to If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Code of Practice BS 6172 BS 5440 and BS 6891 natural gas and BS 5482 LP gas 1994 the Gas Safety Installation amp Use Regulations the Building Regulations issued by the Dept of the Environment the Building Standards Scotland Consolidated Regulations issued by the Scottish Development Department The fan motor of the cooker hood incorporates a cut out device which will operate if the cooker hood is installed below the minimum height recommended in the Technical Information section or if the motor becomes overheated If the cut out device is activated switch off the motor and allow the hood to cool The cut out device will reset itself when the fan motor has cooled Itis dangerous to alter the specifications or modify this product in any way When installed between adjoining wall cabinets the cabinets must not overhang the hob If the room where the hood is to be used contains a fuel burning appliance such as a central heating boiler then
Download Pdf Manuals
Related Search