Acer ALN-201 Network Card User Manual
Contents
1. Green Link BNC Port Boot HOM LED Indicators E There is one LED on the bracket to indicate the link status LED color Green LED ON the 10Base T link connection is successful LED OFF the 10Base T link is NOT successful Remote boot ROM socket their is a ROM socket on this adapter card to support remote boot ROM 2 Quick Installing Guide Follow these steps to install the card 1 Power off PC amp remove cover 2 Plug in adapter card amp connect cable to BNC or RJ 45 3 Replace the cover amp Power on PC 4 Check the system s BIOS setup Configure the appropriate PCI setting 5 Reset PC amp configure your network system 3 Connecting Network Cables Connecting a Twisted Pair Cable Insert one end of the twisted pair cable into the RJ 45 connector on this adapter card Orient the cable terminal jack correctly and push it into the connector until you hear a click Note The other end of the twisted pair cable has to be connected to an Ethernet hub or switch Connecting a 10Base 2 Thin Ethernet Coaxial Cable 1 Connect thin Ethernet cables to both ends of a BNC T type connector For both cables press the T type connector and cable connector together then twist the cable connector clockwise to lock the connector 2 Attach the T type connector to the BNC connector of this adapter card Press the T type connector and BNC connector together then twist the T t2. PCI Ethernet Adapter Card User Guide P N 49 80316 001 Acer Federal Communications Commission Frequency Interference Statement This equipment generates uses and radiate radio frequency energy If not installed and used in accordance with the instructions in this manual may cause interference to radio communications This equipment has been tested and found to comply with the limits for a Class A computing device pursuant to Part 15 of the FCC rules which are designed to provide reasonable protection against radio interference when operated in a commercial environment CE Declaration of Conformity This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 class A for ITE and EN 50082 1 This meets the essential protection requirements of the European Council Directive 89 336 EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility Package Contents One Adapter Card This User Guide One Driver Diskette One T type Connector for BNC connection 1 Product Overview This series card is an Ethernet interface adapter with Peripheral Component Interface PCI local bus It is fully compatible with the IEEE 802 3 CSMA CD Carrier Sense Multiple Access with Collision Detection 10Mbps standard and includes two media interfaces twisted pair RJ 45 connector 10Base T and thin Ethernet cable BNC connector 10Base2 Rear Bracket
3. able BNC connector 10Base T Twisted pair Ethernet RJ 45 connector Thin Ethernet Max segment length 185 meters BNC connector Min distance between two RG 58 cable Nodes 0 5 meters Max number of nodes per segment 30 Twisted pair Ethernet Max cable length to hub 100 RJ 45 connector UTP meters 3 UTP 5 cable Trademarks All company brand and product names are trademarks or registered trademarks of their respective companies
4. ype connector clockwise to lock the connector 3 If your computer is located at the end of a 10Base2 segment connect the thin Ethernet cable to one end of the T type connector and attach a 50 Ohm terminator to the other end of the T type connector 4 Configuration amp Diagnostics With this PCI adapter card you do not need to configure the card manually unless you wan to Enable Disable Full duplex Enable Disable Boot ROM The program file ACERSET EXE in driver diskette can be run to do the above configurations amp the diagnostics of this adapter card 5 Network Drivers The driver diskette contains all the software driver programs supported by the adapter The drivers for different network operating systems are found in separate sub directories See Readme txt file for detailed description NetWare DOS and OS 2 client NetWare server 3 x and 4 x NDIS 2 X MS LAN Manager OS 2 LAN server and client PATHWORK Banyan Vines LANtastic NDIS 3 X WFW3 11 Windows 95 Windows NT 3 5 NDIS 4 0 Windows 95 osr2 a Boot ROM Driver Netware RPL Windows NT 3 5 OS 2 LAN server v3 0 v4 0 LAN manager 2 X 6 Specifications tem Specification System Interface PCI local bus I O address Automatically configured by the system Power requirement 5W at 5V Transmission protocol IEEE 802 3 CSMA CD protocol Software compatibility NE2000 compatible Two media interfaces 10Base2 Thin Ethernet avail
Download Pdf Manuals
Related Search